Search Documents

The care necessary to ensure a reliable estimate of average value from the individual values of a series of bore holes sunk in any alluvial deposit containing coarse gold was well exemplified in checking over the mining returns from a previously bored deposit in Central Otago, N.Z. While the working returns are always liable to vary considerably from bore values in any particular sub-section of an area, still, over any considerable area, the two must check within small limits, if profits are to be calculated and capital raised on the average value given by boring.The present figures have probably more value than those from, dredge returns since accurate measurements are difficult to obtain in irregular water-filled dredge paddocks, whereas in the case under review the paddock walls stood almost perpendicular, and, as the measurements were taken and checked in the empty rectangular excavation, the yardage estimate may be taken as substantially exact.NATURE OF DEPOSITThe area consists of a narrow valley deposit of fluvio-glacial origin, the original deposit having been eroded and the gold reconcentrated by post glacial rivers. The wash is between 80 and 90 ft. deep, and is formed in two distinct layers:(i.) The top layer from surface to 70 ft. or 80 ft. consists of about equal quantities of gravel mixed with glacial drift, and a small amount of clay. The gravel is typical discoid glacial stone of a maximum size of about 4 in. diam. by 1 in. thick, and consists of soft micaceous schist and laminated slate. This upper layer of wash contains no coarse gold whatever, and very little fine; indeed, in mining, the top 30 ft. is discarded without being passed over the boxes.(ii.) The lower layer of wash to bedrock is similar to the upper, except iihat it contains about 10% of larger discoid stone up to 12 in. diam. by It in. thick; 90% of the gold is concentrated in this bottom layer.

Jan 1, 1929

By Sibabrata Patnayak

A major problem during shovel excavation in oil sand mining is the variability of material diggability resulting in varying mechanical energy input, cycle time, energy consumption, wear, and stress loading of shovel dipper-andtooth assembly. This variability greatly influences the mining equipment performance. Different approaches such as empirical ground classification systems, analytical methods, and performance monitoring that are used to determine diggability of groundmass are reviewed. It is concluded that the existing empirical diggability classification systems are site specific and mostly based on rock and therefore, cannot be used for shovel excavation in oil sands. The O&K wedge test is a simple and useful index test for establishing correlations between cutting resistance and geotechnical properties of coal and other soft rock overburden material. But this test, when performed on small size unconfined oil sand samples, may not give reliable indication of diggability because of the boundary conditions on the specimens. Digging predictions made using analytical and laboratory digging models need to be verified with performance monitoring data to better understand the digging effort in oil sands.

Apr 1, 2005

By John M. Hill

Automation technology has many facets, some well tested and proven, some yet to be put to the acid test of economic reality. In this paper, we will limit our purview to the former. Consider, if you will, an automated handling system combining high-speed conveyors and automatic devices on-line which not only provide signals for routing and sorting, but also format those signals for the production of manufacturing, inventory, shipping and billing paperwork. This is not futuristic, but practical and a realistic accomplishment. Therefore, the following discussions will address today's challenges not with tomorrow's solutions, but rather, with an established technology which is playing an increasingly prominent role in materials handling systems. Until recently, relatively modest importance has been attached to the timeliness of information feedback from the production or assembly line, warehouse or distribution center. Thus, initial applications of automatic identification equipment focused almost exclusively upon the control of materials flow - that is, routing, sorting, etc. However, these systems have performed successfully and quietly established an enviable track record as reliable materials control tools.

Jan 1, 1973

By Motyka J, Adamczyk AF, Witczak S

A case study of migration of a paper factory fluid wastes, on the distance of 5 km from an underground disposal site to an ore mine is presented. The ore mine in question, situated in SW Poland is pumping 3.5 m3/s (ca 300 000 m3/day) of groundwater, producing a cone of depression about 150 m deep and several kilometers wide. The migration of wastes (pollutant) occurs within the carbonate karstic aquifer of Triassic age. The aquifer is about 100m thick and is characterized by the coefficient of hydraulic conductivity equal to 8 m/day on the average. The results of systematic measurements carried out for 13 years enabled to estimate the mean breakthrough curve of the pollutant. On this basis and taking into account the coefficient of hydraulic conductivity as well as the mean hydraulic gradient between the disposal site and the ore mine, the migration parameters of the polluting material, i.e. the real flow velocity, the effective porosity and the longitudinal disper- sivity have been calculated. As the measurements considered a long migration distance of the pollutant, the obtained hydrodynamic dispersion constant (dispersivity), in the authors opinion, is reliable enough to be applied for regional groundwater calculations, regardless of the "scale effect".

Jan 1, 1988

By Dirk Claessens

The term ?cost? is too small when describing the destructive power of safety incidents for mining companies. Breaches in employee or environmental safety are felt way beyond the bottom-line: human life can be taken; ecosystems tarnished; the ire of peoples, media and government inflamed; significant halting of production; and high levels of legal and financial challenges. According to a recent survey of Mining executivesi, ?ensuring workforce safety? was the most important issues identified above any other, with a plurality of 31 percent, reigning above capital projects, product efficiency, and equipment reliability. We accept that safety is a most paramount issue, yet for many reasons we keep approaching the problem the same way we have in the past. We need to stop doing the same things decade over decade and try something new. New innovations are significantly changing the fundamentals of how mining companies explore, excavate, produce, refine and distribute their valuable commodities. Technologies such as visualization, analytics, location awareness, and gaming simulation are making these enterprises smarter. Now, attention turns to an area we?ve long held as integral to our business: safety. By using the same breakthrough technologies that are changing our business, we can now boldly imagine ? and credibly strive for ? a world of zero incidents.

Aug 1, 2013

Most coal mines in Chongqing Area are highly gassy mines and liable to outburst of coal cnd methane. In order to harness mine environment and raise the Prodction capacity, methane predrainage is generally taken as a main preventive measure against outburst by all mines. In the recent ten years, the drainage volume per year has increased from 38.25 million m3 to mote than 100 million m3 with a volume over 12 m3 per tome of coal. In some mines, the draining rate is approaching to 50 percent, the rate in mining districts is up to 60 to 70 percent. The predrainage volume accounts for one fourth of total drainage volume. All these have effectively prevented the occurrence of coal and methane outbursts.This is the current situation of methane predrainage in coal mines in Chongqing area, the methods of predrainage to prevent outbursts and related parametres comprise:1. methods, technologies, supervision and effect of predrainage in different geological and mining conditions,2. the change of methane parametres pre-and post-drainage and the analysis of the effect of methane predrainage to prevent outbursts, and3. ways to improve the effect of methane predrainage.Thus the safety, reliability and production of Changqing Coal Mines will be enhanced.

Jan 1, 1991

The phrase "Total-Energy" has, during the past few years, become widely used to describe a wide range of very different operations. However, if accurately described they all have one basic factor in common - energy usage is optimised with the prime mover being powered by gas or oil to generate shaft horsepower and the products of combustion being put to some use. The item which distinguishes a Total Energy system from any other engine or turbine driven project is that orate pains are taken to utilize the waste heat, whether this be in the form of exhaust gases and/or engine jacket ling water. n areas where grid supplies of electricity are readily available, the economics of most projects undoubtedly hinge upon the successful application of waste heat. However, there has been a growing awareness of other benefits, such as reliability of supply, which can be incorporated into the system. In particular these factors sway managements of hospitals and companies with complex computer facilities to examine closely the feasibility of Total Energy, Consequently, in America for example, where many systems have proved themselves the list of applications is wide - shopping centres, apartment blocks, office buildings, airline terminals, universities, schools, motels. And these do not cover the industrial sectors where the range is wider. The total number in North America is now approximately 500 and this to some extent-speaks for itself. In Australia, the real work involved in carrying out feasibility studies for Total Energy is only just beginning. 'in some quarters, the concept is not well received in that it is too new. Therefore, a typical approach is to play safe and wait until some other company has proved its operation "under Australian conditions". This is certainly a realistic approach when considering something revolutionary but as far as Total Energy.is"concerned all the individual components and sometimes combinations, (engines, generators, boilers, air-conditioning units) have been in operation for many years. The only innovation is that they are now all being brought together under one roof. This should not be forgotten when the question "where can I see something like this operating?" is asked.

Jan 1, 1970

At many locations in Australia the decommissioning of mining operations will require the disposal of excess water. If the water is contaminated its disposal may be restricted by government guidelines. The timing of water disposal may be critical to the schedule of close-out. The uncertainty of the annual rainfall input to the water storage and disposal system may determine the success or failure of close-out. The uncertainty associated with any outcome can be used to determine the reliability of the system, or inversely its risk. The technique of Monte Carlo simulation, using the uncertainty in annual rainfall, is applied to quantify the risks associated with water disposal as part of the requirements for close-out in two case studies. In both case studies it is assumed that water disposal is via evaporation only. The first case study is the Nabarlek operation, located about 270 km east of Darwin. This project is required to complete the engineering work associated with its close-out by December 1995. The second study investigates the situation of close-out for the Ranger Uranium Mine, about 250 km east of Darwin. It should be noted that the Ranger mine was examined as part of the annual update of its contingency rehabilitation plan and the probability of implementing the plan is extremely small. The probability of success for the Nabarlek case varied from less than ten per cent to greater than 95 per cent depending on the management strategy. Four possible strategies were investigated for the Ranger mine with the chance of success varying between 20 and 95 per cent. The estimation of the evaporation rate and the area allocated to evaporation was critical in both cases. By applying seasonally based evaporation pan coefficients determined on site, rather than an average monthly value of 0.75, the chance of success was improved by up to 35 per cent for Ranger. Simulation modelling is able to provide information on the likely response of mine water management systems and the level of risk. This information is required to efficiently plan and manage the disposal of water for close-out.

Jan 1, 1994

By Luis Giraldo

Rock bolt installation characteristics near roof falls have been identified as contributing to failure. One documented and regularly occurring failure mechanism is loss of anchorage between the grout and the rock wall of the bolt hole. Key contributors to the integrity of the grout interlocking with the rock mass are the diameter of the hole relative to the diameter of the bolt, resin versus cement type grouts, rock type, and condition of the hole. Smooth bolt holes consistently exhibit less rock bolt load bearing capacity than rough walled holes. The goal of this study was to quantify the benefits of borehole conditioning and develop a systematic approach that would allow improvement of roof bolt performance. A new rock drilling technology, the Helical Drag Bit (HDB), was used in the early stages of this project to condition the borehole. The HDB cuts a prescribed helical groove in the borehole wall. When a bolt is grouted into a hole that has been conditioned using the HDB, the grout fills the helical groove and provides a stronger, more reliable mechanical lock between the rock and the grout. This paper presents results of a series of tests conducted in the laboratory and in the field. Short encapsulation pull out tests have demonstrated considerable increase in pull out strength and more consistent bolt performance when hole geometry is modified using the HDB. The results have also shown that greater load bearing capacity improvements are obtained in mines with weak roof rock, where it is most needed. Additionally, bolts recovered for examination suggest that hole conditioning during roof bolting reduces the effects of finger gloving. Therefore, mines with stronger roof rock could also benefit from hole conditioning. A new roof bolt that uses the HDB principle has been designed and tested. The new system works with existing bolting equipment requiring minimal modifications to the traditional procedure used for installation of fully grouted rebar bolts. The use of these higher anchorage capacity bolts will allow mines to reduce severe injuries and fatalities resulting from ground failures while maintaining or increasing productivity.

Jan 1, 2005

By Y. Nakada, E. J. Fasiska, A. S. Keh, L. Zwell

DURING an investigation of solid-solution hardening of nickel by carbon,' we found that there were no reliable data on the dilating effect of dissolved carbon on the unit cell of nickel. Bernier2 reported an increase in lattice parameter of nickel (3.523A) when an unknown amount of carbon was introduced into solid solution (3.536A). Similarly KG, Tsien, and Misek3 found an increase from 3.523 to 3.531A when nickel was carburized. strong4 studied the variation of nickel lattice constant as a function of dissolved carbon. However, in his case carbon was introduced into nickel by solidifying the melt at 65 kbar. Therefore, his carbon concentrations were much above the highest equilibrium solubility limit5 (2.7 at. pct C at 1 atm). Knowledge of the lattice mismatch between solute and solvent is essential in understanding the mechanism of solid-solution hardening. Therefore, we decided to determine the dilation of the nickel lattice by carbon under the more usual conditions of atmospheric pressure. The material used was Inco Electrolytic Nickel of 99.95 pct purity, as specified by the supplier. The impurity contents in wt pct were: Fe, 0.01; Cu, 0.01; Co, 0.03; 0, 0.005; C, Si, S, N, trace. To this base material various amounts of AUC-grade high-purity carbon were added during vacuum induction casting. Ingots, 2 in. in diam, were heated in a muffle furnace at 1000°C for i hr., hot-rolled to 1/2-in. thickness, and quenched into brine. All ingots with carbon concentration greater than 0.98 at. pct were enclosed in a cast iron box during the heating to minimize decar-burization. Small pieces were then either swaged down to 0.028-in.-diam wire or cold-rolled to 0.010-in.-thick sheets. After the final cold reduction in area of 50 pct, the specimens were recrystallized by heating in evacuated capsules at 1100°C for 60 to 80 sec and then quenched into brine. The final grain size was 50 to 100 µ. The carbon contents of the alloys, Table I, were determined by a combustion method

Jan 1, 1969

By J. L. Huitt

Some of the problems associated with the acid treatment of oil wells are related to the control of the composition of formation treating acid. One test usually made at the well site is the determination of the acid concentration. Heretofore, the concentration of the acid delivered to the well site usually has been interpreted from a hydrometer measurement of the specific gravity of the acid solution. Experience has shown that this indirect measurement of acid concentration can give erroneous results. More reliable results are, of course, obtainable by the titration method; however, this method is not easily adapted to well-site testing. To overcome these objections, a device was developed for use in the field which permits determination of the concentration of treating acid both quickly and accurately at the time of the acid treatment. Its purpose was three-fold, namely, to determine: (1) the concentration of the fresh treating acid, (2) the concentration of the spent acid returning from the well, and (3) the solubility of formation samples in treating acid. The device was designed to operate on the principle of the stoichiometric relation between the calcium carbonate—hydrochloric acid reaction and the carbon dioxide gas resulting from the reaction. By confining the carbon dioxide gas within a reaction cell of the type shown in Fig. 1, the pressure inside the cell is increased. Since the pressure is an indication of the quantity of carbon dioxide gas produced, it may be used to estimate the concentration of the acid, provided an excess of calcium carbonate is used. From information on the volume of the reaction cell, the volume of acid used, and the pressure and temperature of the gas after the completion of the reaction, the concentration of the treating acid may be computed. The reaction cell is essentially a pressure vessel equipped with a pressure gage, temperature indicator. pressure release valve, and a special sample holder. Plastic and metal construction makes the cell both rugged and acid-resistant. The sample holder is so designed that a sample of calcium carbonate (or sample of carbonate rock) can be dropped into the acid

Jan 1, 1956

By C. Wert, P. Bunn

Determination of the solid solubility of gases in metals is usually done by one of two methods. The first is an additive method, in which measurement is made at temperature of the maximum amount of gas absorbed by an initially degassed piece of the metal. Gas additions are made until the dissolved gas first comes into equilibrium with a compound. This method is most useful at relatively high temperatures where the amount of gas absorbed is relatively large and where equilibration of the dissolved gas with the gas atmosphere can be achieved in a relatively short time. The second is a precipitation method. A supersaturated solution of the gas in the metal is held at temperature until equilibrium is established between the gas atoms in solution and a compound. The quantity of dissolved gas is then determined by some physical measurement which is sensitive only to the gas in solution. This method is generally useful in low temperatures. This paper describes measurement of solubility of nitrogen in tantalum whereby measurements at low temperatures using internal-friction methods are plotted together with existing measurements at high temperatures. The solubility is thereby known from less than 0.5 at. pet at 350°C to near 13 pet at 2300°C. Several measurements have been reported of the solubility of nitrogen in tantalum. These are collected in Fig. 1. Three single determinations by Ke,1 Andrews,2 and Brauer and zapp3 are plotted along with a series of measurements by Vaughn, Stewart and schwartz4 and Gebhardt, Seghezzi, and Fromm.5 Although not much doubt exists about the solubility being in excess of 10 at. pet above 2000°C, the solubility indicated at low temperatures depends on whose data are selected as being most reliable. The variation is enormous, being at least an order of magnitude at 500°C. Accordingly, a measurement was begun to examine this discrepancy. The method of measurement finally selected was that of internal friction. A solid solution of nitrogen in tantalum was prepared by heating a tantalum wire in a dilute at-

Jan 1, 1964

By N. G. Cook, N. C. Joughin, A. J. A. White

The rate of face advance in the gold mines is between 3 and 10 m a month, with a median value of about 5 m a month; it follows that faces are blasted less frequently than is planned. There are many advantages in the use of short holes for stoping to give face advances of from 0,7 to 0,8 m per blast. This has the potential for so increasing the frequency of blasting that monthly rates of face advance could be improved significantly. Cleaning with face scrapers is too slow to permit the maximum achievement of a complete clean, drill, and blast cycle for each shift. Short-hole blasting, combined with the use of mechanical conveyors for face cleaning, offers the possibility of completing two such cycles each day, yielding monthly rates of face advance of up to 35 m. Experiments aimed at developing safe, unitized explosive charges well-suited to produce reliable face advances of 0,7 to 0,8 m per blast under a wide range of gold-mining conditions have been notably successful. A novel method of assessing the effectiveness of a blast based on the percentage of holes that leave socket lengths of 5 cm or less was used. Unitized charges of 60 per cent Ammon gelignite, 600 mm long by 25 mm in diameter, appear to be near optimal. The explosive is de-sensitized to obviate detonation by chance mechanical impact, but requires only a 6D detonator for initiation; it has good water-resistance. Means have been developed for producing these cartridges automatically, but the necessary machines will have to be built specially and the cartridges are not yet available in large numbers. A second experiment by way of an extended pilot production trial using these cartridges in holes 0,9 m long is now under way. Preliminary results indicate that drilling and explosive efficiencies and productivity are well above average, even though face scraping is being used. Unitized charges of this type are likely to prove even more advantageous when mechanical face conveyors come into use.

Jan 1, 1975

In the 1890s, The Goldfields Water Supply Department in Western Australia commissioned the diamond drilling of two deep artesian exploratory water bores near Coolgardie (Blatchford, 1899). At the time, in spite of strongly-worded advice to the contrary from the Government geologists, there was a wide popular belief that you could obtain artesian groundwater virtually anywhere providing you drilled deep enough. The first Coolgardie hole was drilled to over 900 m, despite the fact that the bore penetrated granite from a depth of 5 m below the surface. Drilling proceeded for more than 16 months, between July 1896 and November 1897. A small quantity of salt water was struck at a depth of 36 m. The second bore was mercifully terminated at a depth of 50 m, also in granite, with again only a small inflow of salt water. Such were the desperate lengths that were pursued to obtain a reliable water supply for the influx of people in the Eastern Goldfields gold rush. The WA Goldfields continued to rely on huge condensers for water supply until that great engineering feat, the construction of a water pipeline from Mundaring Weir to Coolgardie, was completed in 1903. An enormous network of rail tracks penetrated outwards from Kalgoorlie and Coolgardie for the collection of timber, principally to feed the condensers. Remnants of the rail network are still visible today. The acute shortage of fresh water led to great deprivation, disease and death among the early miners. Today, the water problems faced by the mining industry are thankfully not as severe, but they are nevertheless no less challenging. The southern part of the WA Goldfields is a notoriously difficult area for finding potable quality groundwater. Even as recently as the 1990s, there were occasional serious efforts to find potable groundwater in that area, some very imaginative and innovative. One mining company, working south of Southern Cross, spent many months experimenting with recovery of potable quality water from a shallow freshwater lens overlying hypersaline water in a low permeability weathered granite aquifer. They used very low capacity pumps manufactured from car windscreen washer pumps powered by solar panels.

Jan 1, 2000

By Peter Heine

Diavik Diamond Mines Inc. (DDMI) has treated systems development as an integral part of the construction project when it built Canada?s second diamond mine. Fully aware that the proper collection and processing of operational data is needed to drive business decisions during production and planning, key Performance Indicators (KPIs) were defined to effectively manage operations when the mine went into production. The Production Information Management System (PIMS) allows KPIs to be measured, reported, and transferred to other systems in a reliable and convenient manner. PIMS provides a mechanism to collect real time production data from the various control systems around the site and acts as a tool to ?drill-down? and establish the important cause-effect relationships that impact the value of a KPI. Thus PIMS provides a data collection, storage, management, and an environment in which cause-effect relationships can be analysed and statistically verified. This understanding of the real cause-effect relationships, close to the source of the data and in the context of the operation, can be used to improve both operations and maintenance performance. The PIMS includes the PI Database implementation, its associated external interfaces with the various Control Systems, Cleaning Packaging Weighing System, Environmental System, Enterprise Asset Management (EAM) System, and Diamond Tracking System (DTS), as well as laboratory data collection, custom applications (downtime tracking, data reconciliation) and user clients. The interface with the EAM system provides material flow quantities and equipment availability on which the plant performance reports are based. The transfer of equipment usage to the EAM system is fed into the maintenance notifications and work orders functionality in the EAM. The environmental system interface provides the mechanism for capturing water consumption data required to generate the various regulatory reports. The interface to the cleaning-packaging-weighing system provides the mechanism for capturing batch data for transfer to the DTS for diamond product tracking at the production splitting facility in Yellowknife. The PIMS lab application provides a means of getting sample data into the system for critical metallurgical metrics, and the data reconciliation application provides a means of manually verifying the data before it is published or passed onto other systems.

May 1, 2003

The complete life cycle of a production facility has many phases requiring many different skills and many different personalities. It is not unlike the life cycle of a person and many parallels can be drawn from it. I leave some of these analogous situations to your fertile minds. The author, having worked in operations, plant design, plant commissioning, marketing and many other interesting situations through the industry has drawn from this experience and examples given by many associates in the industry.The phases seen are as follows: Concept Studies û someone has a bright idea of how to make a dollar. Scope Studies û what possible processes/options that could make a dollar. Prefeasibility Study û the æviableÆ scope options are studied to develop feasible options. Feasibility study û defines the concepts that should be designed to make a viable project thus enabling financing and project commitment to be made. Detailed Design û an intermediate step that consolidates the inputs to give a robust plant that can be constructed.Construction û people can see what they thought was going to occur and start to understand the plant. Commissioning û the hand-over of æownershipÆ from the conceiverÆs to the operators. Operations û the ætoyÆ has become reality and money must be made. De-commissioning û the plant has seen out the useful life of the ore deposit, it now goes through a further process required by society.Across these phases of plant design run several countervailing management requirements that can influence the outcome of the plant design. Some of the management rigours that have to be applied to the various phases are as follows: costing basis of the various phases; operational and maintenance reviews; sustainable development; risk assessment; reliability reviews; equipment availability; commissioning time; and environmental review.This paper endeavours to awaken people to the phases that projects require for a successful outcome and the management rigour that has to be applied throughout the phases to ensure the correct intellectual horsepower is applied at the right time to ensure the best outcome.Many of you would be parents and realise this is not unlike the development of children, teenagers, adults, retirees and ongoing.

Jan 1, 2002

By S. B. Flagg, J. F. Barkley

In the past few years an awakened activity in power-plant econ- omies has resulted in a marked improvement in the equipment for generating and utilizing steam. Although the improvement in design and construction of steam-driven prime movers has been greater than that of the steam-generating equipment, the economies obtained with the more efficient engines and turbines have stimulated interest and activity in eliminating unnecessary boiler and furnace losses. Much attention has been given to the boiler room in efforts to obtain proper combustion of the coal, because of the importance of the coal item in costs of power production. As evidence of this increasing interest may be cited the record of the development within the past few years of new apparatus for the analysis of flue gases. Many new forms of apparatus have appeared, including those for the determination of carbon dioxide, oxygen, and carbon monoxide, and others for indicating and for recording the content of carbon dioxide only, as carbon dioxide content is usually a good indicator for the control of furnace operation. Because of the large number of steam-power plants operated by the Federal Government and the number of CO, recorders used therein the Bureau of Mines undertook to collect information regard- ing the practical application of such recorders. Articles published from time to time concerning CO, recorders have been mostly descrip- tive, giving little reliable information as to the results that could be expected from the various types of instruments in ordinary prac- tice, and most of the tests made have been of a laboratory nature. Tests of several different types of recorders were made under service and laboratory conditions in order to obtain needed information. The purpose of the Bureau of Mines in publishing the results is to show the factors which may affect the accuracy of a CO, recorder and the manner in which a recorder should be tested. Readers should note that the remarks on different recorders apply to the instruments tested and not to later instruments of the same makers. In the course of the tests the following details were determined: 1. The lag in recording changes of composition of a flowing gas. 2. The accuracy of each type of recorder.

Jan 1, 1916

By Y Cai, B Hebblewhite

In this paper, the Australian thick coal seam underground mining potential is highlighted and the characteristics are investigated by analysing a thick seam database. It is clear that thick coal seam resources should be mined with a high recovery, productive, efficient as well as a safe and reliable mining method. Longwall Top-Coal Caving (LTCC) is the most recent thick coal seam mining method which has been developed and extensively used in China for the last ten years. The successful applications indicate that this method has a very high recovery and productivity rate and less development cost in comparison with any other thick coal seam mining method. One of the aims of the current study is to seek potential for the application of LTCC as a thick seam mining method in Australia. In this paper, preliminary results of investigation on Australian thickseam potential are given and results of data analysis for potential LTCC seams in Australia are described. The outcome of this study shows a great promise for the application of LTCC in Australian coal industry.

Jan 1, 2002

By F. E. Bash

A GREAT many industrial operations require the application of heat to carry on or complete processes, in which cases the temperatures must often be controlled within very narrow limits. For the lower temperatures, this control is not, as a rule, difficult as a number of types of reliable pyrometers are available for the work; for example, the mercury and resistance thermometers and the thermocouple. For temperatures above a red heat, thermocouples, platinum resistance thermometers, and total radiation and optical pyrometers may be used, depending on conditions. It is often undesirable, and sometimes impossible, to take temperatures of material by immersing the pyrometer in it or by placing the temperature-measuring device in a position in which it will attain the temperature of the material. The pyrometer may contaminate the product; the temperature may be so high that the pyrometer will not hold its calibration, clue to ineffectual protection and consequent contamination; the object may be inaccessible, as a lamp filament, etc. In such cases, a total radiation or optical pyrometer must be used. The disappearing-filament, or Morse, type of optical pyrometer works on the following principle: An objective lens, Fig. 1, focuses the image of the object whose temperature is desired in the plane of the lamp filament at F, which is at the principal focus of the ocular lens shown in the eye-piece. By this arrangement the eye will not have to accommodate itself first to the lamp filament and then to the object at a distance, and the lamp filament will appear superposed on the object. To balance the instrument, the current is adjusted by means of a rheostat until the tip of the lamp filament just disappears against the object as a background. Figs. 2, 3, and 4 show the appearance of the filament when too cold, too bright, and just balanced.

Jan 8, 1919

By P. B. Liebermann

THE resistance to motion offered by mine cars is caused principally by: Rolling friction, flange friction, bending rails, bearing friction and wind resistance. With proper construction and with a fair amount of attention and care, that is, under favorable conditions, the first three items cannot be greatly improved. The wind resistance ordinarily is negligible on account of the slow speeds commonly used. The bearing friction, however, is a variable item, depending upon the design, the bearing material, the lubrication, the location (whether in wheel-hub or on car-body) and the alignment. Under the most favorable conditions the bearing friction will reach a lowest possible value. By the development of a successful anti-friction mine-car bearing this lowest value has been improved to such an extent as to affect the whole system of mine haulage. After being satisfied of their durability and certainty of operation, any investigation into the advantages of anti-friction bearings for mine cars will have to be based upon reliable information as to the saving in power of such bearings. While numerous tests have been made in this direction, the results have not always been convincing, principally because of the rather crude methods that were employed. These crude methods are the main cause of the wide variations existing in regard to the exact amount of the frictional resistance. Frequently an ordinary spring balance is used and the pull necessary to move a certain car or train of cars is obtained by a number of readings. Such spring balances necessarily have a coarse graduation and the continuous vibration and fluctuations to which they are subjected make them highly dependent upon the individual observer. Further, they must be frequently calibrated. Sometimes these tests were made without regard to acceleration, speed or even grade.

Jan 6, 1916