Search Documents

By Clarence E. Sims, George A. Moore

INTRODUCTION IN previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficient time is allowed. For precise work, the method claims preference because the equipment for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the transformation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approximately 2 hr. While it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual error may be more or less constant between samples. For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temperature process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and evolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1948

By R Hindstr÷m

The demand for iron ore has increased dramatically in the last years and is forecast to remain on a stable high production level for years to come. ItÆs expected that the world economy is facing a stable continuous growth of iron ore to two billion tonnes and more over the next decades (Beddows, 2007). Furthermore it is expected that the existing and known high-grade ore resources will decline, and the iron ore industry will be forced to implement more and more advanced beneficiation plants. As a consequence of the more complex beneficiation requirements, there will be a need for modern solutions for iron ore dewatering that are reliable mechanically as well as cost effective and with high capacity per unit at the same time. Conventional vacuum filtration methods have been the most prevalent in fine iron ore dewatering. Product quality needs, lower ore grades, complex mineralogy and energy costs have resulted in iron ore producers seeking better solutions for dewatering, in particular pelletising feed. New advanced filtration methods have been introduced to the market. This paper describes how these modern methods are answering the needs of the industry. Performance of advanced dewatering technologies (pressure filtration and ceramic capillary action filtration) for iron ore applications has been studied, and the findings are based on both industrial and pilot scale experiences on different materials. For example, the results show that the cake moisture content of iron ore pelletising feed can be optimised more effectively by using modern filtration technologies. By selecting the most suitable and adjustable equipment, the effects of variations of feed material on downstream processes can be minimised and the possibilities of processing more difficult raw materials to high-quality pellets are better. The Larox Corporation develops, designs and manufactures industrial filters and is a leading technology company in its field. Larox is a full service solution provider in filtration for separating solids from liquids. As such, this paper compares the new developments in this market area with the prevailing known vacuum filtration technology, but focuses on a comparison between capillary action filters and rotary vacuum disc filters (RVDF). The trade name CeramecG is used to differentiate the Larox filter from the generic term.

Jan 1, 2007

By Kenny Lo

"SummaryFor more than a century, ground freezing has been a construction technique used in stabilization of ground by means of lowering the temperature of surrounding soil strata. This technique is used in circumstances where conventional grouting method is unable to achieve the degree of consolidation required to prevent settlement and water ingress during the execution of underground excavation. Whilst ground freezing is effective in imparting self-supporting characteristics to the excavation profile, it poses significant challenges when it comes to the New Austrian Tunneling Method (NATM) where sprayed concrete is used to support the freshly excavated ground. Sprayed concrete, if used in an appropriate manner, provides a fast, efficient and structurally-reliable means of supporting the structure, especially in underground construction. The evolvement in sprayed concrete technology is attributed to the development of concrete know-how, improvement of spraying technique with the use of automation spraying equipment, more in-depth understanding of sprayed concrete behavior and enhancement of materials used in production of high quality sprayed concrete Not only has this markedly escalated the prominence of sprayed concrete on wider perspective,. the positive development has also pushed sprayed concrete beyond its boundaries, enabling it to be embarked on area of application not considered possible decades ago. Nevertheless, sprayed concrete, for all its placement versatility, still depends largely on the technicality provision very similar to concrete to achieve the required quality. Parameters such as raw material grading composition, curing temperature and cement quality are some of the factors that can easily sway the quality of concrete from one extreme to another. Conducive ambient temperature is critical in ensuring optimum hydration of concrete. This is more important in sprayed concrete where temperature plays a pivotal role in influencing the early strength and long term strength development. The low temperature imposed by ground freezing is everything but ideal for competent hydration to take place. This paper outlines how the innovative use of sprayed concrete helps to overcome the adverse ambient temperature in the construction of a 110m underground pedestrian walkway utilizing ground freezing technique in Hong Kong."

Jan 1, 2016

By A. B. Hildebrandt

P. B. Baxendell is to be complimented for an exccllent piece of work. To our knowledge there has been no previous publication of field data on the flow of oil and gas through the annulus of a well. It is certainly gratifying to see this work on annular flow confirm the previous published correlation procedure on tubing flow. It extends considerably the range under which reliable gas-lift calculations can be made. Baxendell discussed this work with us about a year ago and was kind enough to send a large scale plot of his correlation. We had been designing gas-lift installations on flow through the annulus, assuming that the original correlation of the f factor based on tubing flow' was valid as long as we stayed within the same mass velocity range on which the correlation was based. Doing this work necessitated the use of an equivalent diameter for the annular flow. The equivalent diameter is defined as area' of stream cross section wetted perimeter and for the case of an annulus is D, — D,. Substituting this in the basic equation correlating energy loss along with the area to flow required to convert the velocity, to volumetric flow rate, D (Baxendell's Eq. 7) becomes dell's expression, D,). Similarly, the D in 1.4737 X 10 (M&/D) becomes (D, + D;) for annular flow. On receipt of Baxendell's data, we. of course, recalculated it to put it into the form we were using, and to see how well it agreed with the correlation based on tubing flow. Fig. 1 shows the results, which were certainly gratifying. For low values of (D, - D,) pv, the data coincide with the data on flow through tubing, whereas at high values the data on flow through the annuli appear to be leveling off to a constant value. For very high rates of flow where the turbulence is very high, one might expect the value f to level out and become constant. A bulletin published in 1914 by the U. of Wisconsin presented results of a large number of laboratory teats in air lifting water through short lengths of 1.25-in. tubing. It was possible to correlate a random sampling of

By Morris Muskat

Although the problem of well spacing is one of the most important involved in the production of oil, it must be considered at the present time as still subject to further development. The published literature on this question is so voluminous that we cannot enter here into a review of it, except to refer to the recent papers by L. L. Foleyl and E. A. Stephen-son,2 where other references are cited. However, a decisive and conclusive answer to the problem of well spacing in any general form does not seem to have been developed. And while we shall be unable to present the desired solution in the present paper, it is nevertheless felt that the material to be given here not only provides the physical ground work for the ultimate solution, but shows qualitatively the essential factors that enter the well-spacing problem. Field studies of the well-spacing problem, in which the ultimate recoveries from different fields with different well spacings have been compared, have generally suffered from the lack of knowledge as to the similarity of the inherent characteristics of the producing reservoirs being compared, such as the sand volumes, the sand porosities, the sand permeabilities, the original reservoir pressures, the presence or absence of gas caps, the presence or absence of effective water drives, and the economic limits of production rates at which the various fields were considered to have yielded their ultimate recoveries. Certainly no one who is evaluating originally the economic significance of any oil reservoir would deliberately ignore these phases of the problem. And it is equally certain that no one would reasonably expect the ultimate recoveries from two reservoirs, even with the same well spacing, to be identical regardless of these other factors. More reliable results might be expected from comparisons of the recoveries obtained from different leases with different well spacings, but producing from the same reservoir sand. Unfortunately, however, even conclusions for such studies may be subject to serious errors. The reason simply is that however much one may insist that an operator is entitled only to the oil immediately underneath his surface acreage he will nevertheless drain the surrounding properties as long as his reservoir

Jan 1, 1940

By Bruce R. Sutherland, Jim B. Ramsden, Gerry L. Bolton

Conductive metal powders are important building blocks for today's micro-electronic circuitry. Formulated into inks, they provide the interconnects needed to complete a complex integrated circuit and the means to enter the world of miniaturization. Traditionally, the inks have been based upon expensive metals such as silver, palladium, platinum and gold because of their excellent electrical conductivity and resistance to corrosion and oxidation. The use of a copper based ink, as an alternative to precious metal inks, recently has received considerable attention. Instability in the prices and limited supply of certain precious metal systems have driven up production costs, making the development of a lower cost copper system more attractive to manufacturers. However, lower production costs are on1 y real ized if performance and reliability can be maintained. While the development has been driven by cost, copper does offer some significant performance advantages over noble metal systems: conductivity as good as silver and 4W better than gold; leach resistance better than silver and equal to gold; stability at high frequencies better than gold or silver; strong film bonding characteristics; and compatibility with most solders. These benefits, however, do not come without cost. The inherently reactive nature of pure copper, while providing unique performance properties, makes it difficult to process. Unl i ke precious metals which can be fired in air, copper would oxidize and so requires special furnaces and atmospheres. Despite these difficulties, the transition from precious metal thick film systems to copper is gaining momentum. Manufacturers of high density, high performance circuitry are exploring the performance advantages of copper over gold and silver and the manufacturers of consumer products are considering the potential cost savings of copper over silver-palladium. Sherritt has developed a fine copper powder for this industry. Through association with the ink manufacturers, it has been found that performance properties of the ink vary with the physical and chemical characteristics of the powder. Production Process The production of very fine copper powders at Sherritt is based upon the disproportionation of cuprous ions as outlined in Equation [1] (1).

Jan 1, 1990

By J. Moore Samuel

INTRODUCTORY BEFORE the year 1909, no measurements of dust losses and flue gases had been made at the Copper Queen Reduction Works, at Douglas, Ariz. At that time the "unaccounted" loss of the smelter had reached a figure, that drew attention to the possibility of large stack losses. The measurement of dust losses had not been studied much at that time, and estimates of dust losses, with a few exceptions, were the results of tests by what has been termed "chemical methods," that is, the aspiration and filtration through cotton, wool or some similar medium of a few liters of gas, the dust being weighed on a chemical balance, and the volume of gas computed from the volume of aspirator water. The possible error of this method is enormous, and the probable error much too large for reliable results. Since the object of these tests was to discover not only the extent of the dust losses, but also the possibility of profitably reducing the same, it was decided that the method adopted must have the following characteristics: 1. The sample of gas taken for filtration must be representative of the whole volume of gas, that is to say, it must have the same dust content. This condition will be fulfilled in all cases if the gas sample is drawn off without change of rate of flow. Then it will contain the same proportion of entrained or suspended particles of dust as the original gas. In the case of flue gases which contain only fume, at a temperature above or near the sublimation point, this condition need not be adhered to since the fume will not behave as entrained particles, but more nearly as a true gas. Consequently the gas sample in this case only may be drawn off at any rate of flow. 2. The gas sample taken must be large enough (a) to yield sufficient dust to permit of accurate chemical and physical examination; (b) so that the ratio of the total volume of gas passing through the flue to the volume of gas sample taken shall not be too large.

Jan 6, 1916

By W. J. Carlson, I. lwasaki

Manganese and silica in nonmagnetic tailings from the direct reduction-magnetic separation step were so closely associated that no physical concentration methods were effective. Dilute sulfuric acid dissolved manganese and iron rapidly; manganese in the form of silicates was virtually insoluble in sulfuric acid solutions, thereby governing the maximum extraction attained by leaching. Autoclave leaching at elevated temperatures and at high oxygen pressures reduced the iron extraction to less than one tenth without affecting the manganese extraction. There was an indication that autoclaving solubilized the manganese silicates appreciably. Elimination of iron from leach solutions was carried out by aerating the solution in the pH range of 6.5-7; a platinum-calomel electrode pair provided a reliable indicator for the end point of iron removal. The purified leach solutions were free of interfering impurities for the recovery of manganese as metal, dioxide, or carbonate. Manganiferous iron ores of the Cuyuna Range, Minn., are too low in iron content to be directly useful as iron ores, and too low in manganese content to be termed manganese ores. Common methods of physical beneficiation such as gravity concentration and flotation have not been successful in upgrading this material. The R-N process, when applied to manganiferous iron ores,1'2 produces sponge iron by direct reduction of iron oxides, while leaving manganese as manganous oxide. From fine grinding and magnetic separation of the reduced ore, a tailing is produced which is relatively rich in manganese and low in iron content. The nonmagnetic tailing can readily be leached with acids and then further processed to recover manganese in various forms. In this way, two processes, neither of which would be an economic solution to the Cuyuna ore problem by itself, may be combined to produce two marketable products, thereby rendering the over-all process economically more attractive. This article reports on the results of a leaching study on the nonmagnetic tailings, both in a batch agitation vessel and in an autoclave; on the problems involved in the purification of leach liquors by aeration; and on the recovery techniques used to produce manganese metal by electrolysis, manganese dioxide either by electrolysis or by autoclaving, and

Jan 1, 1968

By C. E. Sims, G. A. Moore

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

By L. J. Murphy

The production of crude oil in the United States is exceeding consumption by one-quarter million barrels per day and, with the possibilities of West Texas, this condition of overproduction, unless controlled, is likely to continue for some time. The resulting low price of oil has caused the operator to observe closely his lease operating costs. The installation of more efficient and reliable machinery has followed and it can well be said that the art of producing oil is on the threshold of a new era. In this advancement electricity has played a leading part. This paper covers only the problem of electricity as applied to lease operation and does not consider other phases of the industry, such as drilling and pipe-line pumping, in which electric power has been utilized economically. In considering electrification of pumping wells, the first question the operator asks is whether or not his costs will be reduced and the second question is whether or not the production will be increased. The third question, although in effect it is closely allied to the first, is the cost of power. The last question can be answered only after a thorough analysis of operating conditions and a study of the power rates prevailing in the particular field under consideration. Within the past few years, the power companies have realized the desirability of a steady 24-hr, pumping load, have made their rates for oil-field service particularly attractive, and in general have shown splendid cooperation in assisting the oil companies in the satisfactory application of electric power to their leases. When everything is taken into consideration, the first cost is practically the same for electric drive as for gas engines when pumping on the beam with individual motors. This cost, at prevailing prices, should aver-age approximately $2200 to $2400 per installation when using 15 to 35-hp., two-speed pumping equipment, including motor and control, countershaft, motor house, belt, installation charges, and a prorated portion of the cost of transmission lines and transformers for serving a number of wells. Since there is practically no difference in the cost of the two installations, it is evident that electricity, to justify its consideration, must have a lower operating cost or produce more oil.

Jan 1, 1928

By Harry T. Davis, Jasper L. Stuckley

The object of this paper is to record and interpret field and laboratory observations made by the writers during five years of study of the barite deposits of North Carolina. Deposits of barite are known to occur in three localities in North Carolina (Fig. 1) two of which—the Hot Springs and Kings Mountain —contain material of economic value. The Hot Springs area begins near Bluff, some 6 miles south of Hot Springs, and continues northeast by Stackhouse; a total length of 7 miles. The Kings Mountain deposits lie along a belt that extends from the north end of Crowders Mountain in a southwestward direction, along the east side of this and Kings Mountain, to Kings Creek, South Carolina. The third locality is 3½ miles southeast of Hillsboro, Orange County, a short distance west of the highway leading from Hillsboro to Chapel Hill. It is not known when barite was first discovered in North Carolina, but production from the Hot Springs area began some 50 years ago. The state has never produced large quantities of barite—usually there have been less than three producers—and definite figures are not available, but reasonably reliable estimates indicate a total production of 300,000 tons. From 1901 through 1920 barite mining was on a seemingly prosperous basis and a large tonnage was shipped from the Hot Springs and Kings Mountain areas. With the depression of 1920 the industry began to decline and production practically ceased in 1926. Geology of the Barite Areas In the Hot Springs area barite is found in the Max Patch granite of Archean age and the Snowbird formation of Cambrian age. The Max Patch granite is of two varieties, one gray to whitish and the other red. The gray granite is coarse, at times porphyritic, and composed of quartz, orthoclase and plagioclase feldspar, with a little biotite and muscovite. The red granite is also coarse and differs from the other only in having conspicuous pink and red feldspar. Both varieties have been much metamorphosed and weathered in places, so that they contain secondary

Jan 1, 1935

By P. I. Page

In mineral exploration the place that yields the first significant result is marked and two questions are posed immediately. Where should the next sample be drawn and how big should it be? At present the answers are arbitrary and ad hoc. They depend on personal experience and sentiment?that is hunch. The thought processes involved in reaching the decisions are unsatisfactory and unsatisfying for professionals. This paper proposes guidance on choosing sample spacing and sample size. The guidance is obtained from the grades of the samples. The grades also imply the extent of influence of each sample assay. Thus sampling and assay are integrated. The integration is achieved by changing the unit of value in which assays and grades are expressed and by exposing meanings and functions of grade beyond that of measuring rock value. The proposals are extended to guide comminution of particle size in sample size reduction and to deal with the problem of erratic high assays. Also, elucidation becomes possible of the computation of a reliable figure for average grade as a statistical weighted mean.

Jan 1, 2005

By N. L. Hayward, V. H. Ness

In the past decade Australia has seen the development, construction and commissioning of three complex processing plants for the treatment of lateritic nickel ores. These have all been based on high pressure acid leaching (HPAL) for extraction of nickel and cobalt into solution, followed by solid liquid separation in a CCD circuit. However, flowsheets for separation and purification of the nickel and cobalt diverge markedly. The existing plants have been commissioned with varying degrees of success, with a variety of problems ranging from materials of construction to inadequate design. While the process problems are not insurmountable, there is much room for improvement. Currently there are several new HPAL plants at the feasibility or financing stage. All of these have adopted one of the existing flowsheets. Most of the enhancements have focused on increasing autoclave size. It is now time to assess the success and failures of the three existing plants and incorporate this experience in a design for productivity, efficiency and reliability. Towards this end, this paper discusses aspects of flowsheet optimization, materials of construction and engineering design.

Jan 1, 2001

By Andreas Stieben, Pierre Lutomski, Wolfgang Bleck, Martin Fischer

"For steel investigation and development, exact knowledge about the microstructural state is required. The information gained from 2D images often can't properly reflect the real 3D microstructural properties. In order to gain reliable information for meaningful models, simulations and correlations, it is necessary to accompany standard metallography with 3D information, which, unfortunately, is very difficult to access. This article presents a procedure for serial sectioning in combination with light optical microscopy. Only standard metallographic tools are employed in combination with image manipulation freeware. 3D microstructural data were extracted from three multiphase steel grades and in two cases virtual 3D-models of microstructural phases were generated.Three Dimensions Of MicrostructuresSince the invention of steel, craftsmen, inventers and engineers tried to improve its properties and tailor them to the requirements of new developments. For systematic development and enhancement of steels, the capability to investigate its inner structure is highly important, because it represents the linchpin between material production and properties. By having an in-depth understanding how production conditions form the microstructure and also how the microstructural state determines the material properties, steel design can be drastically improved. With this knowledge, microstructures can be designed to provide target material properties and process conditions can be identified that form these structures. Due to the key role of microstructure, the capability to gain accurate information about it is indispensable. It is the task of metallography to access and extract descriptive quantitative microstructural data like fractions, sizes, shapes and distributions of the different constituents. The most commonly used investigation tool in metallography is the light optical microscope (LOM). Besides this tool, additional high resolution techniques like Scanning Electron Microscopy (SEM) or Transmission Electron Microscopy (TEM) have become increasingly important. With these and other available methods, extensive information on the microstructural state of a material can be gained. Unfortunately, most metallographic methods have a major loss of information systematically built in. Analyses of microstructures are usually performed on surfaces, i.e. on 2D areas that emerge by cutting through the 3D material structure. This means, a complete dimension of information is not taken into account. How serious this reduction of information is and how it can affect interpretation of structures is exemplarily demonstrated in figure 1, which displays the planar structure emerging from a random cut through a simple 3D structure. It is very difficult to deduce or even imagine the original spatial structure from which this projection emerged and it is impossible to reconstruct it with absolute certainty without further information. The image has emerged from a random cut through a 3D structure of stacked cubes that is displayed in figure 2. The area shown in figure I is outlined. Although artificially constructed, this example demonstrates how distorted and misleading the view on structures can become by ignoring a spatial dimension."

Jan 1, 2012

By Michael B. Bever, Carl F. Floe

The solubility of hydrogen in molten copper-tin alloys is of both practical and theoretical interest. From a practical standpoint, data on the equilibrium solubility as a function of temperature, pressure and alloy composition are valuable for a better understanding of porosity problems in bronze castings. From the theoretical point of view the determination of the hydrogen-copper-tin equilibrium is of interest since it extends the laws governing the solution of gases in metals. This paper presents the results of an investigation of the solubility of hydrogen in representative compositions of the copper-tin system at temperatures ranging from above the liquidus to I300°C. and at pressures from less than 50 mm. of mercury to about atmospheric. Review of Previous Work The solubility of hydrogen in copper was determined by Sieverts and Krumbhaarl in 1910 and by Roentgen and Moeller2 in 1934. Their values are in fair agreement. In 1926 Iwasé3 reported results that were very much higher. The published data on the solubility of hydrogen in tin do not agree. Smithells4 states that no reliable data are available According to Sieverts and Krumbhaar,5 hydrogen is insoluble in tin. Bircumshaw,6 on the other hand, found a definite solubility at 800°C. The latter's experimental procedure did not provide for stirring of the metal and in his opinion he failed to reach equilibrium. Iwasé3 again reported large solubility values. For copper alloys, Sieverts and Krumbhaar5 distinguished between alloying elements that do not markedly affect the solubility of hydrogen, elements that increase the solubility, and elements that reduce it. They named gold, tin, and aluminum as examples of this last group and reported hydrogen solubility data at 1225°C. for the copper-rich side of these alloy systems at atmospheric pressure. Without giving experimental results, they stated that the amount of hydrogen dissolved by liquid copper alloys is proportional to the square root of the pressure as in pure metals. These authors suggested that in a limited way the effect of an alloying element on the solubility of a gas is related to the constitution diagram for the alloy system. Sieverts7 also called attention to the fact that the curve of hydrogen solubility versus composition of copper-tin alloys shows a sharp change of direction at the composition of Cu3Sn and suggested that this compound persists at least to some extent in the molten state. Iwasé3 reported large hydrogen solubility values for several compositions of copper-tin alloys, which appear to be in error.

Jan 1, 1944

By C. W. Green-Halgh

The accuracy with which grade and tonnage of a mineral deposit may be calculated from diamond-drill assays is dependent upon: (1) the reliability of core and sludge samples and (2) the validity of methods used in grade and tonnage calculations. Limitations imposed by drilling and sampling preclude elaborate methods of computation. In adjusting core and sludge assays the importance assigned the core and sludge samples may be based on either the respective weights recovered or the respective volumes represented by each. Only when core and sludge recoveries arc poor do discrepancies between adjusted assays calculated by these two methods develop, in which case the "weight" method gives emphasis to the core sample and the "volume" method gives emphasis to the sludge sample. When the sludge suffers classification within the drill hole, the weight method gives more accurate results; when the sludge sample suffers no classification, the volume method gives more accurate results. Any drilling campaign offers a compromise between desired accuracy on the one hand and expediency, limited time, money. or facilities on the other. Since the determination of grade and tonnage is an approximation at best, a proper basis for their computation requires a knowledge of the limitations imposed by all phases of work upon which the calculations depend A rational basis for coordination of these phases of work requires determination of: (I) the degree of accuracy desired, as a function of the object of examination; (2) the degree of accuracy attainable, as a function of the limitations imposed in the drilling and sampling program; and (3) the validity of method to be used in calculating grade and tonnage from core and sludge assays. This paper presents results of a comparison made between two commonly used methods of adjusting core and sludge assays, the assumptions upon which these methods are based, and the interrelationship of the phases of work upon which these calculations are dependent. Object of Examination The Purpose of prospecting any mineral deposit is to secure sufficient samples from which Ore grade and tonnage may be calculated. Any mine examination, preliminary or formal, has a definite purpose, although its scope may be limited or broad. The type of examination to be conducted is dependent, therefore, 'pan the reason for instituting the investigation; its scope and thoroughness are directly related to economic considerations. It is highly desirable, therefore, that before starting a drilling campaign a complete understanding of the extent of examination and desired degree of accuracy be determined as a means of simplifying the drilling program and unifying the relative degree of

Jan 1, 1946

By Carl F. Floe, Michael B. Bever

The solubility of hydrogen in molten copper-tin alloys is of both practical and theoretical interest. From a practical standpoint, data on the equilibrium solubility as a function of temperature, pressure and alloy composition are valuable for a better understanding of porosity problems in bronze castings. From the theoretical point of view the determination of the hydrogen-copper-tin equilibrium is of interest since it extends the laws governing the solution of gases in metals. This paper presents the results of an investigation of the solubility of hydrogen in representative compositions of the copper-tin system at temperatures ranging from above the liquidus to I300°C. and at pressures from less than 50 mm. of mercury to about atmospheric. Review of Previous Work The solubility of hydrogen in copper was determined by Sieverts and Krumbhaarl in 1910 and by Roentgen and Moeller2 in 1934. Their values are in fair agreement. In 1926 Iwasé3 reported results that were very much higher. The published data on the solubility of hydrogen in tin do not agree. Smithells4 states that no reliable data are available According to Sieverts and Krumbhaar,5 hydrogen is insoluble in tin. Bircumshaw,6 on the other hand, found a definite solubility at 800°C. The latter's experimental procedure did not provide for stirring of the metal and in his opinion he failed to reach equilibrium. Iwasé3 again reported large solubility values. For copper alloys, Sieverts and Krumbhaar5 distinguished between alloying elements that do not markedly affect the solubility of hydrogen, elements that increase the solubility, and elements that reduce it. They named gold, tin, and aluminum as examples of this last group and reported hydrogen solubility data at 1225°C. for the copper-rich side of these alloy systems at atmospheric pressure. Without giving experimental results, they stated that the amount of hydrogen dissolved by liquid copper alloys is proportional to the square root of the pressure as in pure metals. These authors suggested that in a limited way the effect of an alloying element on the solubility of a gas is related to the constitution diagram for the alloy system. Sieverts7 also called attention to the fact that the curve of hydrogen solubility versus composition of copper-tin alloys shows a sharp change of direction at the composition of Cu3Sn and suggested that this compound persists at least to some extent in the molten state. Iwasé3 reported large hydrogen solubility values for several compositions of copper-tin alloys, which appear to be in error.

Jan 1, 1944

By L. D. Wooddy, Robert Moscrip

The simultaneous solution of the volumerric balance and the unsteady-state equation has been used for several years to make performance calculations for combination drive reservoirs. This method makes possible the calculation of volumetric changes of fluids in the gas cap, oil zone, and aquifer which occur as a result of withdrawals and reservoir pressure changes. It does not provide a means for the determination of reservoir fluid distribution changes corresponding to these vollrmetric changes. A knowledge of the fluid saturation distribution in the reservoir at various stages of depletion is important for the determination of the efficiency of gas and water as oil-displacement media and, therefore, for the reliable predicrion of ultimate oil recovery. To provide this knowledge, the displacement equations are solved simultaneously with the volumetric balance and unsteady-state equations. The described calculation procedure has been used satisfactorily to analyze the past performance and to predict the future behavior of combination drive reservoirs under both primary and pressure-maintenance operations. INTRODUCTION The three basic mechanisms by which oil is displaced from a reservoir are: (1) dissolved gas drive—the displacement of oil by the expansion of liberated solution gas, (2) water drive—the displacement of oil by water which enters the oil zone from the aquifer, and (3) gas cap drive—the displacement of oil by gas which ex- pands into the oil zone from the gas cap. The action of gravitational forces may be effective in increasing the efficiency of the basic drive mechanisms. Gravitational forces favor the segregation both of gas and oil and of oil and water, thus tending to shorten the transition zone between oil and displacing fluids. Most reservoirs produce under the influence of a combination of these drives and are designated "combination drive reservoirs". Fig. 1 is a cross section of a typical combination drive reservoir. A calculation procedure for analyzing the performance of combination drive reservoirs has been developed by combining the displacement equations' with the volumetric balance equation' and the unsteady-state equations. The pressure-production performance and the positions of the gas-oil and oil-water contacts are calculated for several stages of reservoir depletion by solving these equations simultaneously, thus affording a basis for: 1. Determining instantaneous and ultimate oil, gas, and water production under various operating conditions. 2. 'Establishing a maximum efficient rate of production, 3. Determining the advantages of pressure maintenance and unitization, and 4. Designing surface installations necessary for primarv and pressure-maintenance operations. DEFINITIONS The calculation procedure for combination drive res-

Jan 1, 1957

By T. Scheldt, M. Lu, A. Myrvang

Abstract: In this paper both continuous and discontinuous modelling are utilised in order to analyze the stability of the Gjøvik Olympic Mountain Hall. The large span cavern (62 m) was built for the 1994 Winter Olympic Games at Lillehammer, and is a unique case study because of the large amount of available input data, through a comprehensive pre-investigation, stress and deformation monitoring program before, during and after the excavation. Phase2, a two-dimensional non-linear finite element program, and the Discontinuous Deformation Analysis (DDA) are used as representative tools for continuous and discontinuous modelling, respectively. The analysis results are compared and discussed taking the reliability of the models, time-consumption and costs into consideration. Some guidelines for the total modelling process, from field measurements to final results, are also presented. Zusammenfassung: In diesem Artikel werden sowohl kontinuierlich als auch diskontinuierlich Modellierung verwendet, um die Stabilität, der in den Berg gebauten Olympiahalle in Gjøvik zu analysieren. Die Olympiahalle wurde 1994 zu den Olympische Spielen in Lillehammer errichtet. Ihr Dach erstreckt sich über eine Breite von zweiundsechzig Meter. Für den Bau wurden umfangreiche Daten durch Voruntersuchungen, und Überwachung von Gebirgsspannungen und Deformationen bevor, während und nach Exkavation eingesammelt. Auf Grund dieser großen Datenmenge stellt die Olympiahalle ein herausragendes Beispiel für den Bau ähnlicher Projekte dar. Für die kontinuierlichen Modellierungen wurde „Phase2“, ein zwei-dimensionales, nicht lineares „endlich Element“ Rechnerprogramm angewandt. Die diskontinuierlichen Modellierungen erstellte man mit Hilfe von der „Diskontinuierliche Deformations Analyse“ (DDA). Die Analysenergebnisse sind mit Rücksicht auf die Zuverlässigkeit der Modelle, Zeitverbrauch und Kosten verglichen und diskutiert worden. Im Artikel werden Richtlinien für den Modellierungsprozess von Dateneinsammlung bis Schlussfolgerung gegeben. Résumé: Dans cet article la modélisation continue et discontinue sont utilisés pour analyser la stabilité de Gjøvik Olympic Mountain Hall. Cette caverne de grande portée (62 m) a été construite pour les Jeux Olympiques d’Hiver de 1994 à Lillehammer, et est une étude de cas unique grâce à la grande quantité de données disponibles, de par un programme de pré-investigation compréhensive, monitorage des contraintes et déformations avant, pendant et après l'excavation. Phase2, un code d’éléments finis non linéaire à deux dimensions, et l’Analyse en Déformations Discontinues (DDA) sont utilisés comme outils représentatifs de la modélisation continue et discontinue, respectivement. Les résultats d'analyses sont comparés et sont discutés, prenant en compte la fiabilité des modèles, la consommation en temps de calcul et les coûts. Quelques indications pour le procédé total de modélisation, des mesures sur place aux résultats finaux, sont aussi présentées.

Jan 1, 2003

By Paul Averitt

The U. S. Geological Survey has been actively engaged in work on coal for more than 50 years. During this long period we have released more than 300 publications containing information about coal and coal reserves, including details on the thickness, distribution, and quality of coal, and the structure and stratigraphy of the coal-bearing rocks. We have also cooperated with state surveys on many similar publications. For many areas these reports are the only reliable published data on our resources of coal. During the last several years we have substantially increased our activities above the wartime low. We now have field work in progress, or reports in preparation, on 13 detailed mapping projects distributed as follows: 1. Pennsylvania anthracite field 2. Casselman Basin, Md. 3. Leslie County, Ky. 4. Deep River field, N. C. 5. Coosa field, Ala. 6. Powder River field, Mont. 7. Spotted Horse field, Wyo. 8. Yampa field, Colo. 9. Paonia field, Colo. 10. Trinidad field, Colo. 11. Durango field, Colo. 12. Chaco River area, N. M. 13. Lewis and Thurston County fields, Wash. For two of these areas; the Paonia field, Colo., and the Coosa field, Ala., we have published recently preliminary reports, and final reports are in preparation. In addition, we are nearing completion of a coal reserve study of Montana, and are beginning similar studies in several other states, as part of a program of revising our estimate of national coal resources on the basis of presently available data. Factors Involved in Making Estimates Our responsibilities include detailed field mapping to secure information on areas of outcrop of coal beds, their range in thickness, nature of roof rock, amount of overburden, correlation of the beds, stratigraphy and structure of the coal-bearing rocks, and the preparation of coal reserve figures based on these data. The computation and estimation of resources of coal in the ground, like that of resources of other mineral commodities, involves consideration of many additional purely geological factors that can be appraised best through such regional studies. Regional variations in the thickness and texture of rocks overlying and underlying coal beds, for example, give evidence as to the probable position of the edges of the basin of coal deposition, or may aid in the delineation of sand-filled channels that sometimes cut out coal beds. It is apparent that the detailed field studies, in which data are gathered, are the basis for coal reserve studies, and in our present program these two phases of work are being carried on together. Previous Coal Reserve Estimates For many years we have been aware

Jan 1, 1950