Search Documents

By Goran Mathisson

PLASMARED is a process in which one well established and one new advanced technology have been merged into a practical tool for production of high quality direct reduced iron at lowest energy consumption and costs. Before describing the process, we have to reiterate the simple fundamentals of making metallized iron from iron ores: The main components necessary are: - Iron oxide - Carbon and/or hydrogen - Heat

Jan 1, 1982

By J. Raatikainen, I. Auranen

"INTRODUCTION Sorting technology has advanced rapidly recently. Of the two possibilities particle sorting has advanced especially in introducing new sensors and the use of multiple sensors. The analyzing and computing lead times have also shortened. This has made it a viable technology option for many applications but not for the most important sorting task at a mine; the run-of mine ore. Bulk sorting, however, has advanced in smaller steps, even if the technology has the capability to tackle the run-of-mine ore and offers a high potential to bring mines substantial economic benefits. The sensors, which are useful are restricted by the difficult operating conditions or by the ore characteristics. One of the important features of run-of-mine sorting technology is the major material handling infrastructure required. The capital expenditure can be substantial requiring good understanding of the sortability curve (grade-recovery curve) behavior of the ore. This paper discusses one industrial case, where substantial amount of data measured from the ore feed belt has been obtained. This data was then analyzed for the grade recovery curves obtainable from that ore with sorting. EXPERIMENTAL The XRF measurement used was the FCA device from IMA Engineering (Fig.1). It is a specially built version of XRF designed to operate with coarse material. The measurement was situated at the main belt conveyor taking ore from the primary crusher to the stockpile. The crushed ore was about 80% -300 mm at a capacity of 1100-1200 tph (Fig.2). Measurement times were varied from 30 seconds to a minute. Measurements were obtained over several months.As the XRF is a surface distribution measuring technique, the measurement was first tested upon accuracy and reproducibility against plant daily wet chemical assays and against on-line Courier feed analysis. As there is a varying delay in the ore stockpile, the delay time was used as a variant in the validation. Different measurement times were tested for accuracy. A one minute measurement time gave a total measurement relative standard error, which was both for Cu and Ni below 3%. The results showed also very robust correlations; for Cu, the correlation coefficient was R > 0,94 for one minute measurements over three months and R > 0,86 for Ni respectively. Fig 3. Shows a measurement period of two hours showing substantial feed grade variations (given as relative value; 1.0 represents the mean value during the measurement month)."

Jan 1, 2018

By D. W. Dean, J. A. Ryder

"A computer system designed to assist in maintenance scheduling and costing, and in monitoring the performance of equipment, is described. The emphasis is on the information retrieval and implementation aspects of the system.INTRODUCTIONThe cost of the maintenance of equipment can account for a substantial proportion of the total costs of any large industry. These costs are made up of the following elements:(i) capital expenditure,(ii) maintenance labour,(iii) maintenance spares,(iv) maintenance overheads,(v) production losses.Control of these cost elements cannot be achieved without a system which maintains and retrieves the necessary infor¬mation efficiently.The system should provide engineering management with the information necessary to:(i) establish the cost of maintaining items of equipment,(ii)establish the economic life of equipment,(iii) determine breakdown patterns for the establishment of optimum inspection, service and overhaul frequencies,(iv) establish work schedules for those responsible for the maintenance of equipment,(v) establish the optimum maintenance labour complement,(vi) establish the optimum stockholding of maintenance stores items,(vii) improve the performance of equipment,(viii) justify the selection of a particular type and make of equipment,(ix) establish the reasons for any abnormal usage of materials and labour, and to(x)reduce the dependence on the human element for the control of equipment maintenance activities.Many industries have comprehensive and numerous equipment maintenance records but they experience great difficulty in retrieving the required information in the time available and with the labour available. Many industries do not bother to maintain meaningful records, because of this difficulty."

Jan 1, 2014

By M. R. Shadnam

This contribution provides an assessment of research and development efforts to optimize SOx, NOx and mercury capture in flue gas. Coa, characteristics and combustion conditions in a power plant have an impact on the types and concentration of flue gas pollutants. These factors can also affect the amount of pollutant removed. This contribution would also provide a comparative study of the technologies that holistically aim remova, of SOx, NOx and mercury altogether in coal-fired power plants. A portion of this contribution provides background information on regulatory drivers.

Jan 1, 2010

By J. N. Baloyi

"In atomic emission and atomic absorption spectrophotometry, the sample is heated to a high temperature and thereby decomposed into atoms and ions that absorb or emit visible or ultraviolet electromagnetic radiation at energies characteristic of the elements involved. The flame test is a very simple form of this technique. The yellowing of a flame by the addition of salt, for example, occurs because the sodium in salt emits strongly in the yellow portion of the visible spectrum. These methods are especially useful for low concentrations of metallic elements in both qualitative and quantitative analysis.Interference on Iep-OES has not always been considered a serious problem, especially in the beginning, when compared with Atomic Absorption Spectroscopy. This was due to the euphoria created by the new technique. It meant that criticism was subdued. The Iep was vastly superior to the Atomic Absorption technique, that the interferences suffered by the Atomic Absorption technique dwarfed the little interferences suffered by the rep-OES technique. This is how rep-OES has had a reputation as an interference free technique."

Jan 1, 2014

By W. Fergusson

This paper takes a look at the use of rubber to provide corrosion resistance and wear resistance in the mining industry. The longer life and reduced down time involved with the use of rubber are stressed, and examples are given of applications in grinding mills, skips, discharge chutes and screens.

Jan 1, 1979

By John Gross

"Introduction.Southern Illinois and Kentucky are credited with approximately 90% of the fluorspar production of the United States. A small amount of high-grade acid, spar is obtained from the ore by band sorting; the greater part, however, is recovered by jigs and tables as gravel spar containing approximately 85% calcium fluoride. In the jigging and tabling operations, galena is recovered, and enough silica and calcite are removed to raise the calcium fluoride content of the gravel spar to 85%. However, the removal of silica and calcite results in a large loss of spar. With increasing depth in the mines, zinc sulphide, sphalerite, is encountered in increasing quantity and the removal of this has become a serious problem. While the sphalerite can be fairly well removed from the spar by present milling methods, a marketable zinc concentrate can not be made. The experiments described below were made on fluorspar ore from Southern Illinois, by the mining experiment station of the U. S. Bureau of Mines, at Rolla, Mo., in cooperation with the Missouri School of Mines and Metallurgy.The ore tested contained. 7.3% lead, 27.9% zinc, 35.7% calcium fluoride, 9.5% silica and 4.7%. calcite.Tests and Results. In some preliminary tests it was noticed that a portion of the finely crushed ore adhered strongly to the sample pans, and upon investigation it was found that the adhering material was practically clean spar. By utilizing this property of adhesion 46.8% of the spar was recovered as a product containing 98.3% calcium fluoride. This suggested the possibility of using electrostatic separation."

Jul 1, 1921

By George A. Hill

WE of the oil industry, devoted to freedom of initiative, free competitive enter- prise, and free American institutions, applaud, with one voice, affirmation by the President of the national will and purpose to preserve and to protect, against all aggressors, "our American way of life with our individual and national freedom." We subscribe utterly and completely to this guiding declaration and seek its further definition as applied to the oil industry. Fortunately for all, the policy of the Government, after adequate study and deliberation, has been given precise definition. The National Defense Advisory Commission, with its patriotic, highly qualified, and distinguished personnel, has unanimously agreed to and adopted twelve general principles governing national defense contracts and also fair labor standard requirements. The President of the

Jan 1, 1940

By Sherwin F. Kelly

NEW trend in geophysics has been uncovered in these depression years, made evident through the thinning cloak of commercial activity, which, in better times, would have completely obscured it. I refer to the increasing use of these methods for geological investigations by federal and state geological surveys. This is a trend that has been gathering momentum not alone in the United States, but abroad as well. Thus, in Poland, the Geological Survey has been playing an increasing role in geophysical work since 1927, and now has- its own geophysical department. The government petroleum producing organization of Argentina has its Geophysical Commission; Brasil boasts a completely equipped geophysical department in its Mineral Production Service; the government of Chile has contracted with commercial companies for geophysical surveys; Peru is planning an intensive program of geophysical prospecting in its petroliferous regions; and Canada has, for several years, cooperated with

Jan 1, 1935

By Jack White

This paper gives details of the results - of careful testing carried out on two types of ball mills, conical trunnion overflow and cylindrical grate discharge, on identical ore. The object of the test work was to determine which ball mill was the most economical to install for future extensions to the Mufulira concentrator.

Jan 1, 1950

By Detlef Ehlert

Energy efficiency is coming to the center of attention in the metallurgical and rolling mill industry due to increasing energy costs, limited resources and political requirements. Also, a green image and energy efficient production is a clear competitive advantage. SMS Siemag, being familiar with automation and measurement equipment, provides an energy data management system which gives transparency over the energy consumptions. All energy relevant media including electricity, gas, water, compressed air and further more can be recorded. The system is manufacturer-independent and allows the use of already installed measuring technology with the possibility of subsequent extension. So potentials for improvement can be recognized and energy savings can be estimated and proven after the implementation of the measures. Being familiar with the processes in the metallurgical and rolling plants, the system by SMS Siemag allows the assignment of the energy data to the production and plant data. Only by this connection, the data can be reduced to key performance indicators allowing authoritative evaluation of energy efficiency. The results are clearly represented on dashboards and support the continuous improvement process. The system also supports the energy controlling with an automatic reporting system, cost center assignment and in support with certification according to ISO 50001.

Jul 30, 2018

By Mario Teruo Enju

Soluções flexíveis, com baixo custo de implantação e manutenção, de sistemas de controle de processos e informação utilizando tecnologias de ponta desenvolvidas em plataforma .Net Framework. Focadas inicialmente em área Metalúrgica, onde eficiência em custos e alta confiabilidade tem relevância fundamental para sua viabilização econômica, estas soluções podem também ser aplicadas em áreas Siderúrgica, Petroquímica e demais segmentos. Integração das informações do chão de fábrica com o sistema de gestão da empresa com objetivo de facilitar a tomada de decisões estratégicas. Banco de dados relacional é o principal repositório de dados para compartilhar informações com a rede corporativa, gerenciado por uma ferramenta de software em tempo real para as lógicas de negócios e camada de apresentação. Maior performance, facilidade de operação, disponibilidade de dados, OEE, manutenção simplificada, acesso e ações remotas são viabilizados, permitindo menor custo e maior eficiência.

Jul 30, 2018

By Simon Chiartano

A global reflection on the design of blast furnace main runner was investigated in this paper. TRB Company used its skills and expertise to understand what the best option for this sensitive component is, including some innovative tools: intelligent block design for safety lining, thermal & thermomechanical numerical simulation, immersive measurement by thermocouples, IR thermal camera, 3D laser scanner.

Oct 1, 2019

By B Beale

Bow-tie analysis is a commonly used tool in the Major Hazard Facility sector to identify, display and control risks that have the potential to pose serious harm to personnel. It is a simple but powerful risk management tool that displays traditional risk assessment outputs as easily interpreted ‘bow-tie diagrams’. These are an effective and versatile communication format that can be applied to any type of risk (eg safety, environmental, assets etc) and as such show great benefit in managing operational hazards in mining.

May 5, 2022

By A Fern, A Hawkes, o, W Smith, K Mee

Serious Injury and Fatality (SIF) prevention remains a priority focus within high-risk industries sector. A major mining operation sought to strengthen their approach to the management of high-risk activities through an in-depth review of all historical incidents that had serious injury or fatality potential (SIFp) events (sometimes known as hi-potential events). The analysis found that the organisation invested a disproportionate level of resources, time and effort on low consequence incidents with a high proportion of SIFp incidents going under the radar. It was found that 76 per cent of SIFp incidents were rated in moderate or lower risk categories and conversely, almost half of those incidents with a ‘serious risk’ rating had little or no potential for a serious outcome. As a result of this project, the operation engaged in a renewed focus on critical risk management and enhanced its operating cadence in critical risk for the workforce. This included bow tie analysis, an update to critical risk standards and increased workforce engagement in the use of critical control verifications in the field. Data analytics with lead and lag indicators continue to provide senior leadership team and risk owners with an understanding of exposure for SIFp and control effectiveness. The audience will take away learnings from a real-world case study that provides data-driven insights of the human, local and organisational factors contributing to incidents with SIF potential. In addition, participants will understand the steps taken to categorise and analyse this incident data and the initiatives currently being implemented by the organisation as a result.

Apr 16, 2024

By B Murphy

Seeking to reduce the likelihood of uncontrolled personnel entry into the operating footprint of a dragline, Coronado Global Resources initiated a review of proximity detection systems currently available and equipment interactions in and around dragline operational areas. At the time of the assessment, there were no established personnel proximity detection systems in compliance with functional safety standards for large machinery in Australia. Our primary objective was to guarantee a functionally safe outcome, particularly by implementing a performance-level-rated system in accordance with AS4024 (Safety of Machinery series of Australian Standards). Applying appropriate detection technologies, the goal was to reduce the residual operating risk for machine-to-machine and machine-to-personnel interactions. A comprehensive analysis of available or in-development technologies was conducted, and a layered approach (demonstrated in Figure 1) was adopted to achieve the desired risk reduction by segregating the sensing zones into distinct areas using diverse and disparate technologies consisting of radar (short); light detection and ranging (LiDAR) (medium); and optical (long). To address the potential limitations of each technology, overlapping layered sensing zones were designed. With LIDAR and optical using two distinct artificial intelligence (AI) systems to classify detections, these were specifically trained to handle the unique environments of a mining operation.

Sep 1, 2024

By A. Miller, M. McNinch, R. Jacksha

Each year, hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The U.S. National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s two-phase implementation of an IoT-based intelligent machine monitoring system.

Caterpillar recently held two, two-day demonstration programs for its mining customers. The event, billed as MineDemo by Caterpillar, consisted of two sessions held on consecutive weeks at the company's Tinaja Hills proving ground south of Tucson, AZ. The program included several classroom sessions that focused on Caterpillar equipment applications, including the VIMS (vital information management system) and the CAES (computer-aided earthmoving system). Also included were field demonstrations and the opportunity to test drive mining-related heavy equipment, including dozers, trucks, graders, shovels and loaders. Featured at the event were the recently upgraded 785, 789 and 793 C-Series trucks. Caterpillar recently announced the availability of the 136-t (150-st) 785C and the 177-t (195-st) 789C. The upgraded haulers have replaced the respective B-Series models. The 218-t (240-st) 793C was introduced in 1996. It, too, has been upgraded but retains the C-Series designation. While attending the press event, the author had the opportunity to test drive the 793C at the Tinaja Hills test site. It was amazing how well the machine handled. The operation was smooth and the braking system was precise. The cab was extremely comfortable. To see a C-Series truck in action, the author also visited Newmont Mining's Mesquite Mine, located in Cali¬fornia, across the border from Yuma, AZ. The Mesquite Mine operates a new model 785C truck. At the mine, temperatures have been measured as high as 58° C (138° F) in the pit. Needless to say, the ability to operate dependably in extreme heat is an important consideration for the mine operators. An interview with the driver and later with management confirmed that the 785C has worked out well. The driver praised the comfort of the cab and the ease of operation. Management reported significant fuel savings and was impressed by the truck's maintenance features.

Jan 1, 1999

.MAX ROESLER, Firmeza, Oriente, Cuba (communication to the Secretary?).-It is substantially admitted by all who have recently been in touch with these deposits that the orebodies lie in the fine-grained dark-green rocks, called diorite by most writers and diabasic by myself. The three points of disagreement concern the agency of included limestone blocks as causes of deposition, the agency of the

Jan 5, 1917

By Arif Emre Dursun

The aim of this study is to present hazard classifications of location, type and causes of accidents in the Turkish coal-extracting industry using the analytic hierarchy process (AHP). In this study, fatal mine accidents were analyzed by pairwise comparison and weighting, and the most important hazards were identified by determining the effective main and sub-criteria among location, type and causes of accidents. For this purpose, first-, second- and third-level hazards consisting of location, type and causes of accident were determined by using the data of fatal mine accidents in underground and openpit coal mining in Turkey between 2010 and 2020.

May 1, 2024