Search Documents

By J. B. Littlefield

The Greenburg-Smith impinger was developed at the Bureau of Mines in cooperation with the United States Public Health Service in 1922 in the course of an investigation of dust-sampling instruments available at that time. Although it is not used extensively outside of the United States, it is now soused in this country to collect samples for the determination of any dustiness, and most of the information correlating degree of dustiness with physiological effect has been obtained by the impinger method. The chief disadvantages in the use of the regular impinger, especially in mines and other places accessible with difficulty, are its bulk, weight, and power requirements. It requires a source either of electricity or of compressed air, which necessitates connections and extension of existing supply lines to each sampling point; the only alternative is the use of a relatively large pump hand-operated with considerable effort.

Jan 1, 1937

By Jörg Wallner

In order to limit SO2 emissions, the Montanwerke Brixlegg AG has installed a desulphurisation plant with the primary aim of reducing the peak emissions from the copper converter that are of particular ecological concern. The author discusses the process requirements, the desulphurisation process selected and the results achieved.

Jan 1, 1996

By Krishnendu Mandal

"For a multi-story building project in Kolkata, a pile load testing program was conducted to minimize pile performance uncertainty resulting from variable subsurface conditions and to verify the pile load vs. settlement response. The program consisted of performing five (5) instrumented load tests on augured cast-in-place (ACIP) pre-production test piles. Vibrating-wire strain gages and extensometers were installed in the test piles at strategic locations to enable measurements of the load vs. deformation behavior of the test piles. This paper presents a description of site subsurface conditions, test pile installation, instrumentation setup for a maintained load test (MLT), static compression pile load test results, and pile instrumentation result interpretation. Average mobilized unit shaft resistance values are calculated.2.0 INTRODUCTIONThe project site is located in Kolkata, near river Ganges, and the proposed development plans consist of constructing six (6)25-story (G+25) towers; see Fig. 1 and Fig. 2 below for approximate site location and proposed development layout, respectively. The buildings were designed to be supported on ACIP piles. A field load test program was implemented to verify sub-surface conditions and pile design. The test program consisted of installing Five (5) instrumented test piles numbered LP1A and B through LP6A and B, and performing static compression load tests on these piles. The piles were instrumented with vibrating-wire strain gauges and extensometers, so that the pile shaft resistance distribution along pile length and the pile toe resistance could be interpreted using direct instrumentation measurements."

Jan 1, 2015

By Ker-Chang Hsieh

Four three-phase equilibria and one two-phase equilibrium in the FeNi- S-0 quaternary system in the vicinity of 1023 K and Pso2 = 1 atm were studied using the following emf cell 2 Pt,o2 (air)Zr02 .CaO/Pso2 = 1 atm, mixture of phases, Au The four three-phase equilibria are sp + (Fe,Ni )S + Ni 3s2, sp + Ni 3s2 + NiO, sp + NiO + N1S04 and Fe2 o3 + sp + (Fe,NOS04 -Y:he two-phase equilibrium is sp + (Fe,Ni)S. The two-.phase equilibrium was measured by using mixtures containing a major portion of one phase and a minor portion of the other. The results are presented in terms of oxygen potential as a function of YNi = nNi/(nN1+nFe) at constant temperature and pso2 = 1 atm. The stability diagram was also calculated using appropriate thermodynamic models for all the pertinent phases. The calculated diagram is in accord with the measured ones.

Jan 1, 1985

By Gary N. Greenfield

This morning, gentlemen, I should like to discuss resin anchors of a type introduced to North America approximately 2-1/2 years ago. We shall also briefly review the basics of mechanically anchored rockbolts so that a general comparison may be made. Previous efforts with synthetic resins were aimed at aiding a mechanical Or "point" anchor, obtain a better purchase in the rock mass. Resin cartridges of the type to be described in this paper are capable of achieving point anchorage or full encapsulation of mine roof or rockbolts. Of significance, therefore, is that unlike a mechanical bolt, placed and tensioned, celtite rockbolts may be fully grouted and tensioned or left untensioned in the installation sequence. Our principle effort has been to offer this system to mining and civil engineers who have encountered difficult rock conditions and wish to reinforce strata to achieve a greater degree of permanence and safety.

Jan 1, 1972

By J. M. Cooper

The HBMS reverb furnace in Flin Flon was originally designed in the late 1920s. Throughout the decades campaign life has been increased due to operational practices, technological changes and brick quality improvements. In recent decades the campaign life had been extended such that a complete rebuild was scheduled every 3 years. The latest furnace rebuild and start up has been after a campaign life of nearly 6 years. Brick construction methods and techniques along with furnace operational practices allow the present campaign to be double that of the historical campaign length.

Jan 1, 2007

By R Ibarra, H Solis, G Teowee, B E. Papillon

The authors have previously described a piezoelectric-based system to measure the dynamic pressure during actual detonation in the field. This technique is used in a water hammer test set-up where a donor detonator is fired first, with the pressure sensor and an acceptor electronic detonator placed underwater in a water tank, and maintained at a fixed distance away from the donor detonator. The functioning and timing of the acceptor detonator are captured using a customised microcontroller board called the water hammer timer. Using such water hammer testing, the effect of dynamic pressure was studied as a function of the magnitude of pressure during the electronic timing countdown. Data obtained indicate there is no significant impact in the timing of the electronic detonators in contrast to what has been reported in non-electric detonators.CITATION:Teowee, G, Solis, H, Papillon, B E and Ibarra, R, 2015. Effect of dynamic pressure on electronic detonator timing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 575–578 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Q. W. Jiang

This paper presents a new process for producing industrial magnesium sulphate using waste water from titanium white plant and magnesium oxide from calcinations of magnesite ore as raw materials. With the laboratory experimental equipment, the waste liquid and magnesium dioxide react effectively at ambient temperature and under atmosphere pressure. Via the press filter, a clear liquid predominately containing magnesium sulphate is obtained. It is further evaporated and crystallized by cooling, separated by centrifuge and dried. Consequently a high quality of industrial magnesium sulphate is achieved as the final product. In the course of process, as the majority of valuable component (SO42-) is recovered in the final product, most of impurities from waste acid is being removed into the by- product. With the simple operational process, it is possible for titanium dioxide plant to resolve the environmental problem completely and benefit from the industrial magnesium sulphate product as well. The filter cakes containing valuable elements such as Mg, S, Fe, Mn, V, Ti are by-product proposed to be used for manufacture of agriculture fertilizer particularly for peanut planting.

Jan 1, 2014

By Pierre Gouvin

"This paper discusses real time monitoring of utility vaults during the reconstruction of the Elliot Bay Seawall in Seattle. The project, undertaken because deterioration of the old wall posed increasing risks to property and lives, impacts businesses, ferry terminals, a rail line, and electrical utilities that distribute power to much of the downtown area. The project, which has been fast tracked to minimize risk and commercial impacts, involves multiple contractors with heavy machinery working in an area one mile long and only a few hundred feet wide. This presented challenges to monitoring of the utilities, as will be discussed in the paper.INTRODUCTIONThe Elliot Bay Seawall (EBSW) was built in over a period of 18 years, starting in 1916. It consisted of a vertical concrete wall placed on a timber pilings and timber relieving platform. The seawall also retained fill that served as the foundation for a road known as the Alaskan Way. The seawall has performed well over the years, but now cracks in the concrete have allowed loss of fill, and the timber piles and support structures have been weakened by marine boring insects.The project to replace the seawall was undertaken because deterioration of the old wall posed increasing risks to property and lives. Because the project impacts businesses, tourism, ferry terminals, and a rail line, it was given a compressed timeline - 36 months from start to finish. In addition, construction activities have been staged carefully to minimize disruption of Salmon and other wildlife living in Puget Sound. In fact, will incorporate several habitat improvements to promote sea life, such as a nature-imitating textures in the surface of the wall and a glass deck structure that allows sunlight to reach the water. (Fig. 1) shows a schematic of the planned new wall.The sheet piling, concrete piles, jet grouting, drilled shafts, ground freezing, and demolition activities are all taking place in the narrow corridor that holds the subsurface ducts and vaults protecting Seattle’s electrical power distribution. If the network of duct bank and vaults were to experience differential settlement during work here, then most of downtown Seattle would be in the dark. Thus it was important to provide real-time displacement monitoring of these utility structures."

Jan 1, 2017

By Thomas Kilpatrick

The liability created by building this railway is the great financial problem before the people of British Columbia at the present time. In dealing with the subject, I propose to divide it into three periods: The Past - The Present - and The Future. The Past The primary objects in building the railway were to provide an independent and direct route for the Grand Trunk Pacific railway into the city of Vancouver, and to open the central and north-eastern portion of the province.. This vast territory, almost one-half the entire area of British Columbia, has great wealth in fruit, agricultural, and grazing lands; timber, coal, water-power and minerals of all kinds, including some of the richest placer deposits in the world. Rivers and lakes teem with fish. Big game, including moose, elk, caribou, deer, grizzly and black bear, mountain goat and sheep, is plentiful and there is an abundance of small game and fur-bearing animals. In addition, its scenic attractions are unsurpassed in Canada. To develop these resources it was considered necessary to build a railway from south to north as a main artery of transportation and, if necessary, branch lines to carry heavy .shipments of coal or other commodities. Lighter freight may be handled by motor trucks from distant points to the railway.

Jan 1, 1925

By Robert M. Dreyer

The first time that a geologist is confronted with the necessity of evaluating a lateritic ore deposit, he may feel that nothing could be easier. Why should there be any problems in making an economic evaluation of a relatively flat-lying, surficial ore body? After several hundred thousand dollars worth of frustrating work often culminating in a series of non-reproducible data - the evaluator may be a sadder and wiser man. This paper will try to illustrate why the evaluation of lateritic bauxite and nickel deposits is among the most difficult problems confronting an economic geologist - and, more especially, how this problem can be solved. Volumes have been published on descriptive and genetic studies of lateritic ores. Obviously, there is time today only for the briefest description of such an ore body. The laterite is a soil formed under tropical conditions and resulting in the concentration, within the soil zone, of certain tri-valent metals.- especially, aluminum and nickel. The soil zone is divided into two parts: (a) the true soil or lateritic zone and (b) the zone of, partially altered bed rock or saprolite. It is important to remember that, whereas bauxite generally is confined to the laterite zone, nickel deposits occur in both the laterite and

Jan 1, 1977

By Paulo Chaves, Márcia Gonçalves, João R. S. Carvalho, Fernando J. A. S. Barriga, Edgar Carrolo, Tiago Luna, Ricardo Rato, Anabela Bento

INTRODUCTION For the last decades, deep-sea marine resources such as seabed massive sulfides (SMS), polymetallic nodules and ferromanganese crusts (Fe-Mn crusts) have received an ever- increasing amount of attention worldwide for their abundance in critical metals and potential commercial value. This interest has mostly been driven by the growing world demand for raw materials, in particular for high- and green-technology applications (e.g., hybrid and electric cars, batteries, photovoltaic solar cells, cell phones, super magnets), as well as by industrialized countries governments other than BRICS states need to secure a more diversified supply of metals, resulting in a new deep ocean exploration boom. Since the oceans and its resources are increasingly seen as indispensable for humans needs and their challenges in the decades to come, this boom increments pressure on marine areas, either in international or within countries economic exclusive zone (EEZ). Since 2002, the International Seabed Authority (ISA) has signed up 29 contracts with several entities and national governments from multiple countries (e.g., Japan, China, Germany, France, Russia, India, Rep. of Korea, UK, Canada, Brazil) for exploration for deep-sea mineral resources in international waters, either for scientific or commercial proposes, which together cover over 1.3 million km2 [1]. In turn, over 300 exploration licenses, covering more than 650,000 km2, have been granted within the EEZ of Pacific countries such as Papua New Guinea, Tonga, Fiji, Solomon Islands and Vanuatu [2, 3]. This number is expected to increase very rapidly, as 77 countries have proposed to the United Nations the extension of their continental shelf in order to extend their EEZ and jurisdiction over potential deep-sea mineral resources [4]. Its estimated that 42% of the potential areas for SMS occurrences, 54% for cobalt-rich Fe-Mn crusts, and 19% for polymetallic nodules lie within the EEZ of coastal countries [5]. In addition, a huge amount of seafloor is yet to be explored and evaluated. Combined, the size of the granted exploration areas represents less than 10% of the overall area thought as most favorable for the occurrence of the 3 types of deep-sea mineral resources above mentioned. This means that today’s assessments on deep-sea mineral resources are only a rough approximation.

Jan 1, 2018

By V. Alexandrov

This paper presents the results of theoretical investigations of the energy requirements of the hydraulic lifting of mined materials from the seabed to the sea surface in the deep-sea mining of solid minerals such as manganese nodules in the Clarion-Clipperton region of the Pacific, situated on the sea floor in water depths of 4,500 m or more. The principal element of the developed underwater transport system is the Underwater Chamber, which is connected by flexible pipeline to a mining machine that gathers nodules from the seabed, mixes them with seawater, and feeds them into a flexible pipeline. In this paper, we discuss the question of the optimum water depth for placement of the Chamber, the interior of which is designed to maintain a 1-atmosphere pressure. We present a method for calculating this depth as it relates to the mechanical characteristics of solid particles, the shapes and size distributions of the particles, particle and slurry density, and other properties. These investigations were carried out in hydro-transport laboratory of the Saint-Petersburg Mining Institute and the hydraulic laboratory of Faculty Environmental Engineering in Wroclaw Agricultural University. KEY WORDS: deposit, nodule, flexible pipeline, pressure drop, concentration, hydromixture

Jan 1, 2005

By Dietrich Gross

This paper describes an advanced oxy-fuel combustion technology for re-melting aluminum that significantly reduces energy consumption and emissions. This oxy-fuel combustion technology developed by Jupiter Oxygen is a patented process for combustion of fossil fuels with pure oxygen while excluding air, thereby creating an undiluted high flame temperature and increased efficiency for process heating in industrial furnaces. This unique process has led to improved heat transfer and longer residence time while maintaining the same process temperatures as with air combustion. The energy efficient combustion process allows aluminum companies to operate at a substantially lower cost due to a dramatic fuel savings of up to 70% for natural gas and waste oil (1). The results of more than 10 years of day-to-day experience utilizing the Jupiter Oxygen Corporation oxy-fuel combustion technology licensed to Jupiter Aluminum Corporation in the aluminum re-melting business are discussed.

Jan 1, 2008

By Bradley V. Nelson

A number of improvements in the ventilation system at the Henderson Mine have been made during the past several years. A key to these improvements was the installation of a computerized monitoring and control system. Employees can determine the status of any of hundreds of devices in seconds through the use of this monitoring system. Mine dewatering pumps, the water treatment system, the ore haulage system, electric power usage as well as other devices are controlled and/or monitored. Ventilation parameters which are monitored include air flow volumes and carbon monoxide as well as the status of main surface fans, mine doors, and ventilation raise doors. Main underground fans are also constantly monitored and can be controlled remotely. These underground fans can be programmed to automatically start and stop to follow work schedules, optimizing air quality while reducing power cost. Mine air heating costs have been reduced by replacing an electrical resistance heating system with a direct fired natural gas heating system at the portal of the ore haulage tunnel.

Jan 1, 1995

By B. C. Lewis

The mining industry has experienced a general trend toward an increasing number of longwall operations, an increasing percentage of underground coal being mined by longwalls, and increasing productivity from the longwalls. Longwall operators have not yet reached a state of mining euphoria. Competitiveness both within the industry and from alternate fuel sources is forcing continued pursuit of higher productivities and lower costs. The following graphics present trends in the industry. Longwall mines, as defined for this presentation, are those reportedly having longwall installations in each of the respective years. Production from both the continuous miner and longwall units is included in the longwall mines. Non-Longwall mines are all other underground mines. Productivity calculations are based on total employee-hours associated with the operation.

Jan 1, 1990

By D. C. Edwards

In an age where customer service and quality drive today's industry and business, no service or product is exempt from these demands. Industry and business are streamlining everything from people to equipment and today have a heavier reliance on the performance and quality of their assets and equipment, (one of the keys to staying competitive). In the mining process industry, the centrifugal slurry pump is a key piece of equipment that keeps product moving and aids in generating revenue for its owner. The continued improvement and customer success lies in a team effort between the mining industry and the pump manufacturers. We, the pump manufacturers, need to keep improving our designs to further extend the life of our pump with fewer failures and promote to our customers proper maintenance of the pumps to continually keep unexpected failures to a minimum. Strict equipment maintenance, as thoroughly demonstrated by the military, is key to the long life and success of any piece of equipment. In the often harsh duty of the centrifugal slurry pump, maintenance is something that requires "attention to detail". No area of the pump is exempt from attentive maintenance. Here, discussions will focus on the areas of the mechanical drive end, wet end, seals, and extended pump shut down and start up. There has not been a slurry pump designed to maintain or repair itself. So in effect, each pump warrants able bodied maintenance persons to maintain them who continually observe all the rules of safety. Prior to any maintenance discussion or action, the issue of safety should always be addressed. Here, as with everywhere, the same rules apply. Work at a safe pace, note all safety precautions, use associated safety equipment and personal protective attire, observe all tagout and lockout procedures, and most importantly, be aware.

Jan 1, 1996

By D. I. Bardos, A. M. Bardos, Paul A. Beck

The approximate effective silicon radii in ternary Laves phase alloys with transition elements and silicon were found to range between 1.16 and 1.21A, i.e., considerably smaller than the atomic radius calculated for elemental silicon. The atomic radii were found to increase with the size of the transition element atoms in the structure. It has been noted by Aronsson1 that silicon in solid solution in iron, cobalt, and nickel has an effective CN 12 atomic radius of approximately 1.20Å, a value very much smaller than the CN 12 radius of 1.34Å derived from the interatomic distances in elemental silicon.7 The unusually short metal-silicon interatomic distances in transition element monosilicides and disilicides have been also pointed out by various investigators.1 A similar tendency was observed by Nevitt in Cr3O type silicides.2 Recent work on Laves phases in ternary systems of silicon with transition elements4"8 suggested that extensive Laves phase fields may occur in such systems.8 It has been pointed out by Laves7 that the MgCu2 and MgZn2 type structures lend themselves particularly well for the determination of the effective radii of the component atoms. In these AB2 phases the B atoms are arranged in close packed straight lines, and their distances are related in a simple manner to the lattice parameters.8 The present work was undertaken in order to find out whether or not the B transition element in such AB2 Laves phases can be replaced to an appreciable extent by silicon. In cases where extensive substitution proves to be possible, the "average atomic radius for the B site" at various silicon contents was to be determined, and the effective atomic radius of silicon calculated by extrapolation to complete replacement of the B component by silicon. The following ternary systems were studied: Ti-Mn-Si, Ti-Fe-Si, V-Co-Si, V-Ni-Si, Nb-Fe-Si, Nb-Co-Si, Ta-Fe-Si, Ta-Co-Si, and Mo-Fe-Si. In all of these alloy systems, the Laves phase solid solutions were found to extend over a considerable range of silicon content. As previously reported,4"8 in the V-Co-Si, V-Ni-Si, and Mo-Fe-Si ternary systems Laves phases do occur, even though there are no corresponding binary Laves phases. In stabilizing the Laves phase, silicon acts as if it were decreasing the effective electron concentration of the alloy.8 A more detailed study of the boundaries of the Laves phases in the V-Co-Si and V-Ni-Si systems has been made and will be published elsewhere. In both cases, the elongated Laves phase fields extend parallel to the B-Si side of the composition triangle, clearly showing that silicon is substituting for cobalt, respectively, nickel over a wide range of compositions. The binary Laves phases NbCo2 and TaCo2 have the cubic MgCu2-type structure. It was found that, in both ternary systems with silicon, again the MgZn2-type hexagonal Laves phase is stabilized and that this phase extends to high-silicon contents. In each ternary system at least three Laves phase alloys of the composition A(B1_xSix)2 were used, x here denoting the fractional substitution of the B-transition element atoms by silicon. The alloys, listed in Table I, were prepared by arc melting in argon. Each specimen was water quenched after a homogenizing anneal of 3 days at 110(FC, except for the Mo-Fe-Si alloys, which were annealed at 1200°C. Metallographic examination showed that most of the homogenized alloys consisted of a single phase, although some had minor amounts of a second phase, as shown in Table I. X-ray diffraction patterns were prepared using an asymmetrical focusing camera of large resolution and Fe Ka radiation. The patterns were indexed, and the lattice parameters of the hexagonal Laves phases were determined from the available diffraction lines of highest indices: (213), (205), and (313). The lat-

Jan 1, 1963

By Josh Savit

Corporate responsibility already encompasses safety and compliance. No longer will companies be able to use differing standards of care to miners based on the country in which they are working. This is not only an issue of social license, but one of global risk management.

Mining is a global industry. The conference is a good example of this, as itÆs jointly organised by professional associations from Canada, Australia and South Africa, and has attracted speakers and delegates from around the world. I commend the organisers for their initiative. I am pleased to be asked to participate in this panel û although I would hasten to add I see myself as perhaps an informed observer rather than an expert. It wonÆt be news to most in this room that AustraliaÆs mining sector is booming. As one of the most productive and diversified mineral regions in the world, this activity is also something that has not escaped the attention of CanadaÆs largest mining companies! This means that I follow what is happening in the industry and more specifically what might be occurring here. Two-way investment between Canada and Australia stood at $9.8 billion in 2005 with Canada as the seventh largest overall investor in Australia with $8.22 billion in investments. The majority of this investment is by Canadian minerals and metals companies. In recognition of the importance of Canadian investment in this sector in Australia, I maintain close contact with our companies. By way of example, in the past two months I spent a week in Western Australia visiting Perth and meeting with companies for example, like Teck Cominco and LionOre as well as seeing various Barrick Gold operations in Kalgoorlie. I attended the opening of AlcanÆs new Asia Pacific Headquarters in Brisbane in August and just two weeks ago was in Cowal, NSW for the opening of BarrickÆs new mine there. Having met with BHP Billiton in Vancouver, IÆm equally aware of active Australian mining interests in Canada. This is not designed to indicate how active I am but rather to demonstrate the dynamism in the mining industry and the diversity of Canadian mining interests in this country and Australian interests in Canada.

Jan 1, 2006