Search Documents

By David J. Forrester

Light metals, most commonly aluminum, magnesium and titanium, and alloys containing them, are used in many industrial applications where lightness, hardness, ductility and resistance to corrosion are needed. However, these metals and their alloys can be potential ignition sources in underground coal mines. There have been documented cases in the past where coal mine explosions have been attributed to firedamp/coal dust ignitions involving light metals or their alloys. When light metals and their alloys are brought into contact with oxygen bearing material, such as iron oxide (rust) in the presence of heat, then a "thermite" reaction can occur. This source of heat can be generated from frictional contact or from merely a glancing blow. This paper outlines the hazards associated with light alloys, how to address the hazard and regulatory aspects.

May 1, 2001

By Z. Smieszek, Z. Szota, P. Gajowski

"A new method for measuring the total quantity of suspensions contained in the electrolyte during copper electrorefining has been developed by the Institute of Non-Ferrous Metals, Gliwice. Electrolyte purity, and the suspensions content in particular, is of essential importance for the quality of electrolytic copper produced during the process. Suspensions contribute to the increase of slime impurities in electrolytic copper and increase losses in noble metals. Up to now, the laboratory method has been used for the· process control which provides analytical results with considerable time delay. Therefore, it is useless for the process control.The measuring method developed enables continuous measurements of a suspensions content directly within the stream of the flowing electrolyte. The principle of measurement is based on changes in optic properties of the electrolyte with varying suspensions content.1. IntroductionIn copper electrorefining, it is essential that the final product quality be maintained. If suspensions are present in electrolyte, the content of slime impurities in electrolytic copper, (such as Pb, Ag, Bi, Sn, Sb, and As), increases which can result in the occurrence of the so-called slime dendrites on cathodes, thus debasing the quality of the product. As a normal suspension content in electrolyte, the contents in the order of several mg/l are considered, usually not more than 5-6 mg/l, while contents exceeding 20 mg/l are referred to as an alarm state. Suspensions present in an electrolyte are usually a light fraction of anodic slime whose main components are metallic silver, lead sulphate, complexes of antimony and arsenic, and sometimes even calcium sulphate; they are mainly composed of very small particles of lead sulphate and antimony complexes. Sometimes - - in case of alarm states - - the so-called ""wandering slims"" can be observed, which are composed mainly of arsenic and antimony complexes. These ""wandering slims"" make a serious technological disturbance. In normal operating conditions of the electrorefining plant, an increase of suspension content can result from such reasons as crack of filter cloth in a slime filter, turbulent flow of the electrolyte, anodic passivation, aeration of the electrolyte, and improper servicing of an electrolytic tank. It is necessary to continuously control the suspensions content in electrolyte for proper electrorefining."

Jan 1, 1989

By Tianzu Yang, Weifeng Liu, Shu Bin, Lin Chen, Wanda Bin

"Vanyukov Process has been mainly applied for processing copper and nickel sulfide ore for more than 30 years. Based on the understanding of the Vanyukov Process, researchers from China introduced the technology into the areas of lead, antimony and bismuth extraction by changing the furnace structure and technical flow, which greatly extended the application area and raised the processing efficiency, thus developed the oxygen-rich side-blow bath smelting (OSBS) technology in 2000. This contribution reviews the history of OSBS technology from four respects: the quantity, the furnace structure, the process flow and the application area. Its potential research direction and industrial application are also summarized.IntroductionVanyukov bath smelting furnace and related bath smelting technology were developed by researchers from Soviet Union who devoted comprehensive research on fundamental theory as well as engineering technology [1,5]. Vanyukov process has been applied for large industrial production since the 1970s and it is still one of the major methods in modem pyrometallurgy process. The appearance ofVanyukov double district furnace and joint double furnace in the past ten years, which are applied for copper smelting, is the most valuable advances of the Vanyukov process [7,8,9]. However, the application ofVanyukov process was limited in copper and nickel sulfide ore smelting, and few countries adopted this process except Soviet Union."

Jan 1, 2013

By P. J. Best

Due to its low mine production costs, competitive rail rates and low sulfur content, the Southern Powder River Basin (SPRB) now commands 30 percent of the U.S. utility coal market. In 1996, production exceeded 260 million tons, a growth of 110 million tons since 1989 and 15 million tons over 1995. Continued growth is expected as the second phase of the Clean Air Act Amendments (CAAA) looms. This growth will be the greatest in the southern part of the basin, where coal quality is higher. This article is an overview of supply and demand issues affecting markets for SPRB coal. It reviews the current markets for SPRB coal and addresses future prospects for market expansion.

Jan 1, 1998

By H. Somekawa

The fracture toughness and deformation structures an AZ31 magnesium alloy processed by equal-channel-angular extrusion (ECAE) were investigated. The average grain sizes of as-ECAE and annealed-ECAE alloys were 4.0 and 16.3 µm, respectively. The plane-strain fracture toughness, Kip, in as-ECAE and annealed-ECAE were estimated to be 27.3 and 23.5 MPam1/2, respectively, by stretched zone analysis. The fracture toughness indicated higher value with grain refinement. From optical microstructural observations in samples after fracture toughness tests, although deformation twins were observed in annealed-ECAE, no deformation twins were observed in as-ECAE. From TEM observations, the dislocations on basal and non-basal planes were activated in as-ECAE. With grain refinement, the activations of dislocations on both basal and non-basal planes were possibly related to the reduction in formation of deformation twins in as-ECAE. In addition, in comparison with direct extruded process, ECAE process was more effective method to improve the fracture toughness in magnesium alloys.

Jan 1, 2006

By B. Zeytuncu, O. Yucel, O. H. Celik, M. H. Morcali

"The Taguchi method was used as the experimental design to determine the optimum conditions of cementation behavior of the ruthenium chloride solution. Cementation was carried out using metallic zinc powder. The experimental conditions were studied in the range of 25-45°C for reaction temperature (A), 30--60 min for reaction time (B), 0.5-1.5 for pH of solution (C), and 30--50 mg for zinc powder (D). Experimental parameters and their levels were determined in the light of preliminary tests. Orthogonal array (OA) L9(34) consisting of four parameters each with three levels, was chosen. The optimal conditions found for ruthenium, such as a reaction temperature, reaction time, pH of the solution and mass of zinc, are respectively: 45°C, 45 min, 1.5 and 50 mg. Under these conditions, the ruthenium cementation efficiency obtained by theoretically and experimentally was in good agreement, which were 99.8% and 99.7% respectively."

Jan 1, 2013

By Keenneth Huachaca

Durante los últimos años, en las operaciones mineras subterráneas surgió la necesidad de contar con diversos mecanismos de control operativo orientados a la mejora de los procesos productivos. Actualmente estos mecanismos tienen muchas dificultades, principalmente en las comunicaciones, debido a la volatilidad de las labores, costos altos de instalación y daños físicos a los medios de comunicación existentes (fibra óptica, cables coaxiales y leaky feeder), lo que dificulta principalmente la extracción de datos de los equipos móviles livianos y pesados. En este trabajo se presenta un nuevo medio de comunicación que se adapta a la volatilidad de las labores mineras, tiene bajo costo de instalación y está exento de sufrir daños físicos en su trayecto, por lo que garantiza una alta disponibilidad y fiabilidad de la transferencia de información del subterráneo hacia los centros de control existentes, donde la información es procesada, a la vez que facilita la aplicación de los mecanismos de control para la optimización de los procesos productivos.

Sep 20, 2019

By Arcy P., D&apos Banister

Several gold-antimony geochemical anomalies were outlined near Stibnite, Idaho, using the humus sampling technique. Several hundred reconnaissance humus samples were collected and analyzed by a combination fire-assay atomic absorption method. The results partially outlined several gold-antimony anomalies and are very encouraging for further work in this part of Idaho.

Jan 1, 1970

Jan 1, 1924

By Bora Derin

The partial pressure ratios of sulfur and oxygen for several copper flash smelting plants were derived using the Reddy-Blander (RB) model and predicted dissolved sulfur contents available in the literature. The sulfide capacities (Cs) of six different flash smelting plants (FeO-CuOo.5- CaO-MgO-FeOu-AlO15-SiO2) slags were calculated. The log (PO2/PS2) versus matte grades of various industrial processes was determined. The PO2/PS2 ratio increased with an increase of copper grade. The calculated partial pressure ratios for the copper flash smelting are in good agreement with those of the experimental data.

Jan 1, 2003

By Bruce Macdonald

Operational monitoring of slope stability can be achieved by space based InSAR monitoring platforms. Natural and man-made rock slopes are monitored using a novel stack-based InSAR method that exploits both persistent point scatterers (PS) as well as coherent distributed scatterers (DS) such as areas of pavement and sparsely vegetated surfaces. The new method, Homogenous Distributed Scatterer (HDS)-InSAR identifies InSAR targets by using adaptive multilooking of statistically homogenous pixel neighbourhoods combined with thresholding the differential temporal coherence of each target candidate with respect to its surroundings. HDS-InSAR preserves PS and therefore forms a direct generalization to our proven DualScale-PSI method. The density of HDS exceeds that of PS by more than an order of magnitude often providing essentially continuous coverage over urban and industrial landscapes featuring a mix of infrastructure with mostly bare soils or rock surfaces. The improved coverage enables better definition of surface motion and underlying geology, which will lead to superior interpretation of the geophysical mechanisms causing the surface deformation, e.g. through improved integration with 3D deformation modeling. We illustrate the performance of our new HDS-InSAR method compared to DualScale-PSI using displacement results from Vancouver, Canada; Bingham mine, USA; and the Palabora mine, South Africa.

Jun 1, 2012

"Increasing demand and market economics have pushed the mining industry to adopt improved mining practices and minimize losses. Simulation, in this regard, has proved to be an efficient tool to help in decision making purposes. We present the development of a discrete event simulation model for a large-scale open pit mine to run experimental scenarios for near optimal decision making. A mixed integer linear goal programming (MILGP) optimization model is also presented for shovel allocation optimization. The mathematical model will be coupled with the simulation model at the dispatching stage for shovel allocation optimization and thus it will act as the link to optimal short-term schedule to assist in achieving better mine plan compliance across short-term and operational planning time horizons. The main contribution of this work so far is the development of the MILGP model and development, implementation and verification of the simulation model on a large scale oil sands open pit mine case study. The results obtained so far are promising and have been validated against the historical data of the mine, proving the applicability of the model for experimental scenario analysis. INTRODUCTION It is essential for mining operations to adopt efficient operational methods and technologies to cope with market demand and economics. Mining operations, on the other hand, being capital intensive, find it risky to bring in any changes. Simulation is a tool that can help in this regard for better decision making purposes with an improved and quantitative measure of confidence. A true representative model that satisfies the objectives set for the simulation is essential to achieve its applicability for decision making purposes. A similar simulation model is presented in this paper for analyzing the operational KPIs of a large scale oil sand open pit mine with truck-shovel operations. This paper is aimed at providing an overview of the development of the model and the statistical outcomes validating its applicability for experimental scenario runs and thus for better decision making purposes. A mixed integer linear goal programming (MILGP) optimization model is also presented in this paper that acts as an upper stage in a multi-stage dispatching system. The optimization model is proposed to be linked with the dispatching logic in the simulation for optimal shovel assignments and target productions by reading available mining faces directly from the short-term extraction schedule. This model is aimed at bridging the gap between operations and short term extraction schedule; and may help achieve better compliance between the two."

Jan 1, 2015

By Greg Wyartt

"At an Australian iron ore open-cut mine, 129 separate blast patterns (consisting of 38.5 million tonnes /42.4 million US tons, equaling 28% of annual blasted tonnes) were initiated using electronic detonators. 87 patterns were designed as per site methodology using ‘vectorial’ initiation timing sequences (blast direction and relief specified only), while the remaining 42 patterns were designed with interactive initiation timing sequences - hole by hole sequencing based on the measured site specific primary shock wave (P-wave) velocity and distance between blast-holes. The intention of this project was primarily to reduce material size presented to the crushing circuit, and also to determine if productivity benefits could be obtained by the use of interactive timing."

Jan 1, 2017

By H. Staton, V. Suontaka, E. Sharifi

"Flotation circuits are typically controlled using on-line elemental assays obtained from the slurry lines. In base metal applications, X-ray fluorescence (XRF) analyzers are the most common instruments for elemental analysis of the slurries. Eagle Mine has been utilizing a Courier XRF Analyzer since 2014. Typically, in XRF analysis, the sampling rate is 10-25 minutes which is good enough for manual process control. In 2018, Eagle Mine upgraded the Courier XRF analyzer with the Rapid Measurement module that is based on reflectance spectroscopy. This option reduces the sampling rate to 10-15 seconds, while maintaining the superior accuracy of the XRF analyzer. This paper presents the results from implementation of Rapid Measurement at Eagle Mine.INTRODUCTION Eagle mine is an underground mine producing nickel and copper concentrates. Eagle Mine is owned by Lundin mining and located in the Upper Peninsula of Michigan, USA. The Humboldt Mill, previously an iron ore processing facility, was refurbished in 2014 and is used to process the ore and produce separate nickel and copper concentrates. Approximately 2,000 metric tonnes of ore is milled per day. Ore is processed using a conventional crushing followed by single stage ball mill and flotation. Nickel and copper concentrate are transported to facilities in North America via rail car. A bulk copper-nickel concentrate is produced by separating the copper and nickel minerals from gangue material by flotation. The copper-nickel bulk concentrate is reground, followed by one stage of cleaning to reject further gangue minerals. The bulk cleaner concentrate is then subjected to a final flotation stage where the copper and nickel minerals are separated from one another through the addition of lime. Final concentrate grades are 14% Ni and 2% Cu in the nickel concentrate and 31% Cu and 0.8% Ni in copper concentrate."

Jan 1, 2019

By Gurubasayya Swamy

This paper presents the performance study of sag mill in the processing of gold ore. Deterioting ore grade and high demand of metals has tremendously influenced the SAG mills. Today?s high capacity Semi-autogenous grinding (SAG) mills expand vast amounts of energy and in doing so consume tons of shell liners and steel balls, while processing ore. Semi-autogenous (SAG) mill performance is influenced by ball charge, feed properties, shell, grate, and pulp lifter design. In the performance study of SAG mill, based on the results obtained it can be observed that SAG mill performed better at feed size +4 inch and grinding media consumption 0.90kg/mt. In the present study the effect of crusher bypass on SAG mill performance, an immediate drop of throughput ranging from 10-20tph is observed. Keywords: sag mill, pulp lifters, grinding media, energy, consumption, throughput

Sep 1, 2012

By C. K. Skokan

Various geophysical tools have been tested over the last eight years to evaluate their usefulness in defining damaged rock zones in an underground facility at the WIPP site in New Mexico. These tools include direct current and frequency domain electrical methods and seismic tomography. The electrical measurements show a "drying rind" to exist around older excavations. Seismic tomography confirms that a rind of lower velocity has developed along walls. In combining these tools, a monitoring program has been proposed to observe long-term changes in bedded salt. Results from the monitoring of electrical data over a 2-year time period illustrate the applicability of the technique in an underground environment.

Jan 1, 1993

By Chen Zhiqiang, Luo Chuansheng, Chen Ziqiang, Liu Jianguo, Rao Jinshan

To comprehensively utilize the valuable resource in tailings, increase the economic benefit of mine, reduce the amount of tailings, prolong the service life of tailing dam, the comprehensive utilization of tailing resource is arousing the attention of more and more mines. Research of comprehensive recovery of feldspar and silica from Cu-Mo floatation tailings has been furthered. Technology of "De-sliming-Magnetic Separation-Reverse Flotation-Feldspar and Silica Separation" has been developed to utilize the resource. Slime is removed and reagents cost is reduced by de-sliming. The specific effective collector ZL is used in gangues reverse flotation, and GZ-818 is the collector in feldspar and silica separation. The grinding operation is vital to ensure the liberation degree of feldspar and to eliminate the reagents pollution on minerals surface. To a Cu-Mo flotation tailing assaying K2O 5.22%, Na2O 2.22%, Fe2O3 1.95%, Al2O3 12.05%, SiO270.66%, superfine K-feldspar and silica concentrates can be produced. The feldspar concentrate productivity is 29.67% assaying K2O 8.99%, Na2O 2.86%, Fe2O3 0.16%, Al2O3 16.99% and SiO2 68.92%. The silica concentrate productivity is 14.20% assaying 0.17% K2O, 0.04% Na2O, 0.01% Fe2O3, 0.55% Al2O3 and 98.17% SiO2. The technology provides technological reference model for the similar mines.

Jan 1, 2014

By Jorge Alberto Soares Tenório, Flávia Paulucci Cianga Silvas, Bianca Medeiros, Denise Crocce Romano Espinosa, Ivo André Homrich Schneider, Daniella Cardoso Buzzi, José Roberto de Oliveira

"AMD is one of the main problems associated with mining activities and the techniques used in their treatment may be the biosorption. The aim of this work was to study the rice husk as a biosorbent for the AMD treatment keeping constant: pH (2.6), biomass concentration (1g.L-1), temperature (25°C) and agitation (175rpm). And varying the contact time of 5, 20, 60 and 240 minutes. Rice husk samples will be characterized before and after the biosorptives tests through analysis of SEM and IR. The micrographs indicate the occurrence of micro-precipitation and changes in biomass physical structure. Since the infrared spectra indicate changes in functional groups present in the biomass before and after the biosorptives tests. AMD synthetic solutions will be analyzed by ICP in order to quantify the metals concentration captured by biomassIntroductionThe preoccupation for the environment has led the industry in general, to treat their waste. As the only industrial activity is increasing, the pollutants generated must undergo treatment processes aimed at reducing pollution, and therefore, less aggression ecosystems.In mining there is waste water with accumulation of heavy metals, and these are harmful to health of living beings, thus being one of those industries responsible for some pollution of the environment. These wastewater in contact with oxygen to generate an acidic water is called acid mine drainage (AMD). This aqueous solution has a pH below 3 and varieties of dissolved metals. When this solution comes in contact with water, generates a series of environmental problems, so there is a need to recover the metals present in the DAM."

Jan 1, 2012

By The Staff

"SummaryDetermination of uranium in ores may be made by measurement of their radioactivity.The method most commonly used is that of measuring beta radiations with the tray-type beta counter. This will give an accurate uranium determination provided the sample does not contain thurium and that the beta and gamma activities have not been disturbed from their natural state of equilibrium. Such a loss of equilibrium will result from mining the ore or from the weathering of the surface rock.A method is described which eliminates errors due to loss of equilibrium. The beta and gamma activities are measured simultaneously in one simple operation. This method is recommended for assaying samples of products from milling operations and its use is limited only by the presence of thorium in a ratio greater than one part of thorium to twenty parts of uranium.A third method is recommended for the analysis of exploration samples and diamond drill cores, which may be assayed in the uncrushed state.Rapid determinations of a large number of samples is possible with the pressure ionization chamber, which is sensitive to gamma activity."

Jan 1, 1950

By T. K. Bose

According to the Intergovernmental Panel on Climate Change (IPCC), the average global temperature has risen over the last century. If this trend continues over the next century, the IPCC projects a significant increase in temperature and a rise in sea level. The changes in climate could adversely impact human health, agriculture, water resources and ecosystems. Most national and international agencies have concluded that our use of carbon-rich fuel is responsible for global warming through the greenhouse effect. In the future, the situation may get worse if the increased need for energy in countries like China, India and Brazil is fulfilled by burning fossil fuel. Advanced natural gas-fuelled vehicles have the potential to reduce carbon monoxide and reactive hydrocarbon emissions substantially compared to gasoline vehicles. Further environmental benefits can be realized by using a blend of natural gas and hydrogen. Such an approach will help create an infrastructure for an eventual transition to hydrogen.

Jan 1, 2005