Search Documents

By Craig H. Olson

"A new ship dock at a Philadelphia area refinery will be capable of docking the largest tanker to travel the Delaware River, the Stena V-MAX, which will induce significant lateral loads. The loads at the dock, a system of mooring dolphins and platforms, will be resisted by over 150 pipe piles, including some 20- and 30-in diameter, reinforced, concrete-filled pipe piles and H-piles. Construction included driving the pipe piles to the required ultimate capacity, flushing the pipe pile casing clean of overburden materials, followed by drilling rock sockets into the underlying Wissahickon Formation. The Wissahickon Formation is a complex subsurface that includes variations in depth to bedrock, rock quality, degree of weathering and the presence of very hard quartzite lenses or inclusions. Because of the problematic subsurface, the designers and client requested extensive pile dynamic analysis (PDA) testing by TRC Engineers (TRC).Before beginning, the contractor requested that TRC perform the WEAP (wave equation analysis program) to evaluate the proposed hammer (APE D30-32 open-end diesel) to drive the piles into the proposed bearing strata while maintaining allowable compression stress levels. The WEAP provided a prediction of blow counts and stresses for various ultimate capacities, and showed that for the HP14x89 piles with a required ultimate capacity of 480 kips, a blow count of at least four blows per in at a stroke of 8.0 ft was necessary.New Approachway RampThe PDA testing began at the new dock approachway ramp, parallel to the existing one. The new structure is a 300-ft-long by 21- ft-wide concrete deck supported on seven bents; each has two 24- ft-diameter steel open-ended pipe piles. Every pipe received an HP 14 x 89 x 80-ft pile that was later driven beyond the pipe pile tip to create a composite pile. The pipe piles were later cleaned of overburden materials and finally filled with concrete and rebar. At each bent, a cap was installed on top of each pair of pipe piles, and then a prefabricated concrete deck was added."

Jan 1, 2008

By C. Sunderman, R. Jacksha

"Mine monitoring through various sensors is a vital component of successful miner safety and health programs. Data from environmental, geotechnical, infrastructure, and other types of sensors are increasingly being used to discover and mitigate health and safety concerns in underground mines. In many smaller underground mines, as well as in new development headings of larger underground mines, leaky feeder communication systems may be the only available means to transport crucial monitoring data. In addition, data transport is increasingly being delivered using Internet Protocol (IP) while older forms of serial communication are being retired. This paper presents the selection, configuration, and testing methodologies that were employed by researchers from the National Institute for Occupational Safety and Health (NIOSH) to integrate commercially available land mobile data radios into an existing leaky feeder communication system to provide Internet Protocol data transport. INTRODUCTION To enhance the health and safety of their mining workforce, mine owners and operators are increasingly installing environmental monitoring and control systems in underground mines. Real-time, mine-wide monitoring is becoming a reality with the implementation of the Industrial Internet of Things (IIoT) into the underground mining industry [1]. However, not all underground mines, especially smaller mines and new development headings in larger mines, have the information technology (IT) infrastructure in place to handle the data transport requirements for the newer IP-based technologies that are part of IIoT. This was the case with a mine in the Western United States; it lacked the infrastructure to perform critical monitoring in remote headings. The mine partnered with the U.S. National Institute for Occupational Safety and Health’s (NIOSH’s) Spokane Mining Research Division (SMRD) to develop and evaluate a cost-effective solution for real-time monitoring of geotechnical conditions in relatively remote sections of the mine. This paper describes SMRD’s solution to leverage the mine’s existing leaky feeder system to achieve IP data transport using commercially available land mobile data radios. DATA RADIO SELECTION The primary selection criteria for the data radios were network data format, modulation type, and radio channel spacing. The network data format decided upon was Internet Protocol. This format allowed for straightforward integration between the IP-enabled data acquisition system located in a remote heading and the network switch located in the control room. It also eliminated the added complexity of additional network hardware such as Ethernet to Serial converters. IP additionally provided a direct path to integration into higher bandwidth networks, such as fiber optic, should they become available."

Jan 1, 2018

By D Yan, D Connelly

Beneficiation of magnetite is an integral part of the future of iron ore processing. Historically, the focus of Western Australian producers has been on exporting direct shipping ore (DSO) namely haematite. The future for new DSO resources is limited so companies are changing their emphasis into processing the very large, undeveloped magnetite ores in Western Australia (WA), using beneficiation to produce shippable magnetite concentrates. These magnetite resources require higher cost processing techniques such as fine grinding and beneficiation to produce saleable concentrates. This distinct difference, from the DSO ores, has led to the development of a number of new technologies. This paper reviews: the different techniques used for magnetite beneficiation and provides some case studies in the WA industry; the use of mineral liberation analysis (MLA) to describe the nature, grain size, occurrence and associations of the mineralisation;the consideration of coarse cobbing as a critical upgrading; the application of high pressure grinding rolls (HPGR) to save energy; how the field of magnetic separation has resulted in new machines with higher field strength (SLon Separators); ultra fine grinding requirements of magnetite concentrates; andthe application of reverse flotation to reduce silica in the concentrates.

Jan 1, 2009

By J. Oliver, J. Cleason

"With maintenance costs rising and an increasing demand for higher production, the use of sealed spherical roller bearings can reduce maintenance costs while providing increased production uptime. The sealed spherical bearing has increased bearing life by slowing the ingress of contamination. This paper will describe how contamination and bearing wear is reduced by reviewing case histories from coal and metal mines that improved their production by decreasing downtime using sealed spherical roller bearings. INTRODUCTION The spherical roller bearing (SRB) is a robust rolling element bearing that can accommodate high radial loads, low to moderate axial loads, and misalignment with no loss in carrying capacity. (i.e. Figure 1) Because of these characteristics, it is a favorite in mining applications and many other heavy industry applications. Primary applications are the various pulleys on conveyors. Coal and hard rock mines have hundreds of miles of conveyor lines and countless head, tail, drive, and idler pulleys. Maintaining the bearings on these pulleys and replacing bearings that have failed can be a huge expense to a mine in components, labor and downtime. Ideally, the bearings are replaced when the pulley is changed out according to the maintenance cycle, about every 4 years. Reality, however, causes the bearings to be changed out every year, or sooner. These premature bearing replacements can cause production shut downs for as long as 8 hours. Conveyor pulleys have been targeted at many mines as the single biggest maintenance pain point.The primary reason for replacing conveyor bearings is internal wear from fine, solid particle and water ingress through the bearing housing seals. (i.e. Figures 2 & 3) Traditionally, the bearing is mounted in a split pillow block housing (SAF, FSAF, SDAF or SNL are typical industry styles) with only labyrinth seals (LER/LOR) for protection against the ingress of contaminants. The bearings are lubricated with grease. A common way to extend the MTBR is to purge the bearing system with large quantities of grease to flush out the contaminants. If the bearing, and thus the housing seals are not frequently purged with grease, fine solid contaminants enter the housing and bearing through the labyrinth cavities."

Jan 1, 2015

By G. Beckstead, L. Gormely, R. Zimmer, K. Hanneman, B. Nethery

As part of the EIS and permitting activities for the Pogo Mine in Alaska, a risk assessment study for the water management plan was carried out. The basis for the study was a site water volume and contaminant balance model. Probabilistic modeling was carried out using the @Risk Monte Carlo simulation package to investigate the frequency, quantity, and quality of discharges under varying assumptions. The results were used in discussions with regulatory officials as part of the permitting process for the project. The simulation allows probabilistic modeling of key environmental parameters based on input frequency distributions involving both quality and quantity of flow. When combined with predictions of water treatment plant capacities and removal efficiency, this was very useful for defining the likelihood of important regulatory outcomes. Based on the model, certain project modifications were made. Using the simulation as a basis, ongoing dialog with regulators led to consensus that all potential risks have been considered and mitigated for the Pogo Mine according to their likelihood and severity, and that regulatory requirements would be achieved. The paper describes the model and some of the applications for which it was used.

Jan 1, 2005

By Jewel A. G. Gomes

Lead has long been an USEPA priority pollutant and an important environmental and health concern because of its toxicity at ppb levels. In light of health and exposure data for lead, the EPA has set standards for Maximum Contaminant Level (MCL) and a MCL Goal (MCLG) as 15 ppb and 0 ppb, respectively. An accurate and rapid measurement of lead in the field remains a technical challenge. In this work, a relatively new method of deploying a nanoband electrode system using anodic stripping voltammetry has been optimized by changing deposition potential, electrolyte, and plating time used for the measurement of Pb(II) in water samples. Green rust has been proven to be an efficient intermediate matrix for removal of lead contaminants. We also report here the removal efficiency of lead using green rust produced by electrocoagulation, both directly and indirectly. Lead containing floc was also characterized through XRD, SEM, and EDAX techniques.

Jan 1, 2008

By Olga A. Gomon, Alexey N. Lozhko

The technology of heat treatment for metal frequently includes multiple fast heating and cooling of the products surface. If the product is heavy-weight or long-size, its moving from a zone of cooling to a zone of heating and return require a long time. Other important condition of ensuring qualitative surface at heat treatment is intensification of cooling phase. It is known that turbulization of a flow activates heat exchange and increases efficacy of cooling without increasing volume flow rate of water. Additional difficulty is to ensure the regularity of heating and cooling on length of a product. The technology of cyclic heat treatment of rolling products, at which mobile zone of turbulent heat exchange is formed on the surface of a product, was developed and realized. The submission of water occurs through to face spray systems. Each of the systems has six long-range atomizers, which are located circularly. Two flows of water move towards one another along a surface of a product. When they collide, the right zone of turbulent heat exchange creates heat transfer in this zone of 10-15 time more intensive than on other surface of a product. The effect of moving turbulent zone on length of a product is reached by changing the proportion of volume flow rate of water, which is created by face sprays. The speed of movement for turbulent zone along a surface of a product is chosen so, that the cooling takes place on a small depth only. Then after passing the turbulent zone over a determined site of a surface, its temperature recovers fast owing to hot internal layers. The parameters of process were determined by mathematical simulation of cooling in an installation. The equations for dynamics of movement of collision point of flows, which were received this way, are interesting supplementary products of research. The experiments show that frequency of movement of turbulent zone is an important technological parameter. It defines mechanical properties of a surface and should be chosen depending on a profile of product and metal grade. The results of comparison of mechanical properties of a surface of various rolling products, which were received by developed and conventional technologies, are described in this report. Dependence of regularity of mechanical properties on frequency of movement of turbulent zone is adduced.

Jan 1, 1998

By D. Sancho, M. Weber

"At the start of a new shaft project, a specific number of ground investigations are performed. However, it is not uncommon that the ground conditions during shaft sinking may differ from the designed ones. Therefore, it is extremely important to use tools which minimize discrepancies and to include a monitoring system in the shaft design to collect sufficient data. The paper presents an overview of existing monitoring techniques and discusses future works required to improve, not only the construction during shaft sinking, but also the lining design methodology. INTRODUCTION In most cases, the investigations performed at the start of a new shaft are based on the analysis of rock and soil probes obtained from boreholes. In practice, such analysis performed on a single core often leads to different results when conducted by various experts. The discrepancy in core analysis influences further rock mass assessment and design assumptions. It is not uncommon that the ground conditions during shaft sinking may differ from the designed ones, which affects the estimated stress and strain state of the shaft lining. Therefore, it is extremely important to use tools which minimize such discrepancy and to include into the shaft design a monitoring system to collect sufficient data, which enables control of important phenomena, not only during shaft sinking but also during the life of the shaft. Furthermore, the information collected during shaft sinking, while it is important for proper shaft lining design and updates to the shaft lining due to the local mining and geological conditions, it is also important after shaft sinking. In the whole shaft lifetime, it is not uncommon that the shaft lining is damaged and the liner needs to be renewed (Figure 1) due to various reasons. For this purpose, detailed information collected during construction can be extremely important."

Jan 1, 2019

By M. A. Boucher

The purpose of my presentation is threefold: a) to make you aware of what is available in Canada in terms of refractory minerals. b) indicate the mineral deposits that have potential for development. c) show the advantages of Canada as a supplier of electrical energy necessary for the production of electrofused minerals. Canada is a producer of natural refractory minerals, electrofused minerals, and synthetic refractory minerals. Several deposits also have good potential for development. The natural refractory minerals produced in Canada are shown in Table 1. The major minerals by decreasing order of importance in terms of tonnage and values are: dolomite, graphite and magnesite.

Jan 1, 1992

By Michael E. Stout

M.A. Industries, Inc. has developed and is now offering on a commercially available basis, complete systems to recover and recycle lead from spent SLI batteries. The system begins with the breaking and separation of the component parts of the batteries and subsequent treatment of the effluent water produced by this operation. The recyclable materials recovered from this process are metallic lead, lead paste and polypropylene. The lead paste is introduced into a process to convert it from a lead sulfate to a lead carbonate. The process also regenerates the salt solutions into reusable carbonate. The lead carbonate is then leached into an acid bath where it is later recovered by a proprietary electrolytic process. The metallic lead is recovered in a short rotary furnace producing metal for further refining and alloying. The polypropylene is further washed and then introduced to a reclaim extruder along with the proper modifiers and additives. The resulting resin can then be sold on the open market to injection molding processors. This complete system greatly reduces the amount of waste to be disposed of and completely complies with all applicable EPA guidelines.

Jan 1, 1993

By G. Keizer

Cortez Gold Mine (C.G.M.) is located in Lander County, Nevada, approximately 80 miles southwest of Elko, Nevada. It is accessed via Nevada State Highway 306 south from Interstate 80. This operation is a joint venture between Placer Dome U. S. Inc. (60% operator) and Kennecott Corporation (40%). The claims which supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka Counties. These include the Cortez and Horse Canyon deposits all operated by C.G.M. Joint Venture. Other deposits outside the C.G.M. claim area include; Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain/Eureka Trend.

Jan 1, 1993

By C. Patrick

Project scheduling is a deterministic technique utilizing single estimates of activity durations. In reality, activity durations are stochastic and can be better represented by probability distributions. This paper describes the development and utilization of a project scheduling simulation which combines analytical scheduling with stochastic activity durations. The purpose is to provide a method to analyze the sequencing of mining production processes and predict the effect of any planned changes. The simulation is demonstrated through realistic examples, such as longwall face-to-face transfer sequencing and the effect of varying advance rates on longwall development sections. Statistical data, to make more informed production decisions, are generated in the form of project activity/path criticality and project duration distributions.

Jan 1, 1995

By Neal Lee, Braden T. Lusk, Brendan McCray

"Selection of a blasting agent for optimum performance is based on many variables. Often, a decision is made with regard to product cost and field testing. Defining optimum performance can be difficult, since downstream effects of fragmentation on loading, haulage, processing, and energy consumption are not immediately clear. Many operations are beginning to optimize their blasting programs “on the bench,” by utilizing information generated downstream at the loader and/or crusher. During the evaluation of a blasting agent, factors such as velocity of detonation, gas production, and sensitivity are typicallyconsidered. Alternatively, brisance (“the shattering power of an explosive material distinguished from its total work capacity”1) is not. Brisance affects the immediate area surrounding a borehole. Fractures produced here during the shock phase of detonation are believed to have an important effect on rock movement and fragmentation. "

Jan 1, 2017

By T. Gollaher

The use of paste thickeners for mineral tailings has gained increasing acceptance by the mining industry throughout the world and in the U.S. during the last five years. Advantages of water recovery and environmental sustainability are the driving forces for paste as an alternative to conventional thickening and the slurry pond. This paper presents a summary of the differences between paste and conventional tailings thickeners, along with recent examples of full-scale paste thickener installations.

Jan 1, 2010

By G. France

The Blair Athol Coal Mine (BAC) is a large open cut operation in the Bowen Basin of Queensland, Australia. Current mine capacity is about 11 million tonnes per annum (Mtpa) of export coal. On-line analysis at BAC consists of two Coalscan 9500s installed directly on the output of the crusher plant and immediately before the product stockpiles, while a third Coalscan 9500 is installed on the transfer conveyor feeding the train loading bin. The two product Coals cans have a dual purpose. The first is to provide real time coal quality data directly back to the mining operations. The second is that of modeling the product stockpile with accurate on-line information. This modeling enables both production and coal quality personnel to accurately examine the coal quality of each stockpile with a degree of resolution which previously had never been achieved.

Jan 1, 1999

By Theodore H. Boggs

The battle of the gold standard is not limited to one country alone, or even to a single group of countries. It is being waged merrily in many important commercial and industrial quarters. Though it is not always a practical issue calling for immediate attention, it is none the less, quite widely, engaging the thought of bankers and other students of finance. The controversy arises, in the last analysis, because of the desire of men to secure a stable currency. There are two ways of restoring a reasonably stable currency system: (1) the re-establishment of the gold standard, or (2) the deliberate and artificial management of a paper currency. Both systems are well known. The gold standard was in use prior to the war in the principal commercial countries. A currency of inconvertible paper has been at times employed in the past in various countries; for example in Britain from 1797 to 1821, and in the United States from 1862 to 1879. The gold standard, as all are aware, implies the selection of gold as the standard of value. The unit of value is a fixed weight of gold and, so long as the standard remains unimpaired, all other means of payment are maintained at a parity with standard gold coins. And gold coins alone constitute the standard money, inasmuch as their value as bullion equals their value as coins. Under the gold standard this would not be true of any other form of money, although all other varieties of money, including bank notes, government notes and silver coins would be freely convertible into gold money. Strictly speaking, the gold standard also implies that the gold money in turn shall itself be freely convertible, through melting, into gold bullion and freely exportable.

Jan 1, 1925

By L. M. Gochioco

The U.S. coal industry is under-going dramatic changes to meet the challenges of the keenly competitive fuels market. The application of innovative technologies is needed to improve safety and to increase productivity in order to make coal more competitive as a fuel. As more coal companies shift into capital intensive longwall mining, there is a clear need to invest more in exploration before mine plans are made. Coal seam anomalies may create adverse mining conditions. The early detection of these anomalies could make the longwall mining safer and more productive through improved planning. A standard exploratory drilling program can provide only limited geologic information. The seismic reflection technique can be used to detect coal seam anomalies and is effective in reconnaissance surveying. Recent advances in the quality of coal seismic data have increased the success rate of seismic surveying. Therefore, surface seismic surveys, coupled with selective drilling, will come to play an integral role in coal exploration in the 1990s.

Jan 1, 1990

By Abb Raymond

Finely processed industrial minerals in "powdered" form have long been utilized by the plastics, paint, rubber, paper, ceramics, and adhesives industries as fillers, extenders, coatings and special additives. These minerals, primarily calcium carbonate, talc, kaolin, titanium dioxide, and the like, have provided economic, uniform and consistent base materials which have, in turn, been used by the referenced industries to manufacture quality products. The focus of this paper will be the development of equipment and systems at ABB Raymond for the dry processing of such non-metallic minerals in order to meet what have become increasingly stringent requirements of the producers of these minerals. Changes in these requirements seem to have been accelerating rapidly during the last ten years, and it is expected this process will continue into the 1990's.

Jan 1, 1990

By Richard E. Barrett

SOME YEARS AGO I was associated with a mining operation which, because of its isolated location, burned wood for heating purposes. Year after year the tractors and tucks hauled the cordwood in from the edge of the ever-growing clearing. Each year the cartage costs became greater. The degree to which transportation distances affect the economics of fuels obviously varies with many factors, but the main criterion is the amount of heat a unit weight of the fuel will produce. For in-stance, wood is limited in most cases to a haulage distance of a few miles. Coal can be shipped hundreds of miles, whereas petroleum and gas ?can be transported thousands of miles. The world is now on the brink of having a new fuel -uranium. It has the virtue of being so concentrated that transportation costs can, for all practical purposes, be disregarded.

Jan 1, 1958

By E. W. Shaw

The past year (1950) has been a big one for the oil industry in Canada, with new records being set in almost every phase of exploration and development activity. New highs were reached in acreage holdings, in geophysical activity, in wildcat drilling, and in field development and production. The only item that did not show a substantial increase over recent years was the amount of reserves added by new discoveries. This was not due to a decrease in the number of new discoveries, however, hut rather to the fact that most of the discoveries were made during the later months in the year and could not be fully evaluated by the year end. The foregoing remarks pertain mainly to activity in Western Canada. In Eastern Canada, operations continued on a modest scale. with exploration drilling down slightly from the previous year but with development drilling and production at about the same level. Returning to Western Canada, it is observed that the general exploration play was one of expansion and intensification. The issuing of new petroleum and natural gas regulations by the province of British Columbia precipitated a moderate entry of companies into the northeastern part of the Province.

Jan 1, 1951