Search Documents

Several major impediments threaten the successful delivery of tunnel and under-ground construction projects. In addition to technical design and construction risks associated with tunnel projects, many of which are well understood, budgetary pressures, funding constraints and the complexity of procuring, administering and executing multiple concur-rent projects in a large program could also have a catastrophic impact on the program?s objectives. Contributing factors often include poorly managed design, procurement, construction, managerial, organizational, market and stake-holder risks, as well as nonconforming inputs or outputs to the costs and schedule, or any other potential inabilities to deliver the required or desired results. A strategy to prevent ?failure? of a project requires a proactive and holistic approach to risk management. Through planning, identification, analysis, management, monitoring and control of the project?s risks (both threats and opportunities), attention to management of risk will in-crease the probability and impact of positive events and decrease the probability and impact of events adverse to a project?s objectives.

By T D. H McGrath, O Baker, W P. Staunton, C Ypelaan

"The carbon-in-pulp process has been used extensively in the gold industry since the late 1970s to recovery leached gold from solution. Despite more than 30 years of experience in operating carbon circuits, average gold solution loss has remained at an average of 0.02–0.03 ppm (mg/L), higher than the ‘best practice’ target of 0.01 ppm.Process modelling, such as SIMCIL developed by the Curtin Gold Technology Group (GTG), can provide information on optimum set points; however, manual control of the circuit limits the potential benefits.An automated carbon measurement device, the Scout Carbon Meter, has been developed to allow for automation of carbon concentration measurement, and automated control of the carbon transfer pumps. This paper describes the results from the evaluation of the first two prototypes of the meter.Citation:Staunton, W P, McGrath, T D H, Ypelaan, C, Baker, O and Eksteen, J J, 2016. Optimising Carbon Management - Increasing Gold Recovery and Decreasing Costs with the Carbon Scout, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 225–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By P. Hale

"The trend to drives of more than 10,000 hp on large-capacity ball and autogenous mills for increased operating efficiency has been limited by factors in the conventional drive system. A solution to this problem, using modern developments in static converter technology, is the concept of driving the mill directly without gearing using a low-speed, low-frequency synchronous motor with a cyclo-converter power supply.This paper presents various practical arrangements of mill and low-speed motors giving the specific advantages of each system. The means of controlling inrush currents on starting and of spotting by the use of variable-frequency control are outlined in general form. Several gearless ball mill drives are scheduled for start-up in European cement plants and further orders have been placed."

Jan 1, 1970

By D. R. Derry

This paper up-dates an earlier paper by the author on the rate of new Canadian mineral discoveries and the exploration methods which were principally responsible for these finds. He concludes that the ratio of exploration expenditure to production value must be increased if we are to provide sufficient new reserves for the future.

Jan 1, 1970

By P. A. Riveros, R. Molnar, F. J. Baša

"An acidification circuit was installed and operated at the Agnico-Eagle Silver Division refinery in Cobalt, Ontario, for treating ~300 m3 of a concentrated cyanide waste solution with the purpose of recovering its cyanide and metal values. The acidification circuit was designed from parameters determined experimentally at CANMET. Available refinery equipment was assembled according to a flowsheet developed by Agnico-Eagle Mines. The process produced a regenerated cyanide solution containing >15 g/L of free cyanide, which was used for leaching gold ore at another Agnico- Eagle operation. It was estimated that the value of the recovered cyanide offset the treatment cost. BackgroundThe Silver Division of Agnico-Eagle Mines needed an economic and effective method for disposing of ~300 m3 of a concentrated cyanide waste solution that had remained in the plant after the operation was shut down in 1989. As a result of extensive recycling and evaporation, the solution had become practically saturated with metals, cyanide, thiocyanate, sulphate and other components, and was, therefore, an environmental liability for the company. A partial analysis of the solution is presented in Table 1. Initially, the use of cyanide destruction methods was considered by Agnico-Eagle, but the estimates indicated a considerable cost with no credits to be gained. A research project carried out by CANMET showed that a simple procedure consisting of acidification, filtration and reneutralization was the most attractive option, because it enabled the recovery of a substantial portion of the cyanide. Furthermore, the metals would be recovered in the form of a solid precipitate. The research showed that conventional AVR was not applicable because of excessive cyanide degradation and low HCN volatilization obtained with this particular solution (Riveros et al., 1996). This paper describes the procedure used to treat the concentrated cyanide waste solution and the operating practices of the large-scale acidification circuit run at the Agnico-Eagle refinery."

Jan 1, 1998

By C. Perez

In mineral processing plants it is important to estimate rock composition, size and grindability to improve control of the grinding process. It is well known that variation in ore grindability and size distribution directly affects mills power consumption and throughput. This paper extends a general machine vision approach for on-line estimation of rock mixture composition using color information. Our proposed rock lithological recognition method requires the following steps: division of each image into sub-images, color feature extraction using the Binary Quaternion-Moment-Preserving thresholding technique (BQMP) and support vector machines (SVM) for classification. The BQMP thresholding technique splits the image in two and chooses representatives of each half using the histogram as features. The statistical parameters of the color data can be expressed using the quaternion moments into the representatives. This method can be recursively applied to the sub-images, obtaining 5x2n features in n iterations. Once the feature vector has been computed, each vector is assigned to one of three classes using a classifier. The method was tested on a database containing 20480 sub-images (64x43 pixels) of five ore types as follows: massive sulphide (MS), disseminated sulphide (DS), net textured (NT), gabbro (G), and peridotite (P). These ore types were assigned to three grindability classes: soft (MS), medium (DS and NT) and hard (G and P). The database was divided in 2 subsets: 15360 sub-images used for training and cross validation and 5120 sub-images used for test. The classification accuracy was compared with a method previously published based on a mixture of principal components analysis (PCA) for color, and wavelet texture analysis (WTA) for texture feature extraction. WTA-PCA approach reached a 76% accuracy in test while our BQMP method reached 90% of classification accuracy using only color features. Experimental results show that our proposed method yields excellent results compared to previously published results. Keywords: rock classification, lithological classification, grindability estimation

Sep 1, 2012

By M Gerards, M Steinberg, T Graham

The quality and quantity of Australia’s secondary deposits, which include tailings streams and tailings dams, are higher than most countries’ primary deposits. In addition, these secondary deposits have already been mined and processed, meaning that the recovery of high-grade product requires low capital and operating costs.The most widely used process for the recovery of these valuable fine and ultra-fine hematite iron particles is the wet high-intensity magnetic separation technique, originally developed by Dr Jones over 55 years ago. Many of the original machines are still working today.The aim of this paper is to demonstrate the capabilities in terms of grade and yield of using sophisticated magnetic separation modules. All results and figures are obtained from test work and design and engineering work with material from the Pilbara. In addition, consideration is given to dewatering of iron ore product and tailings.Two types of tailings have been identified for processing. Firstly, tailings that have already been deposited in a tailings storage facility, and secondly, live tailings streams from an existing wet iron ore beneficiation plant. In both cases, the technical and practical results are shown along with relevant flow sheets and plant layouts. Finally, this paper highlights the total predicted power and water consumption, capital requirements and projected operating expenses.The results show that the operating costs are significantly lower than the mining and processing operations that are required for an equivalent amount of iron ore. The recovery of iron depends on various factors but is within the 30–50 per cent range at an equivalent grade to the mainstream product. Another significant benefit is that the magnetic separation process is water positive, meaning that water is released rather than added in the process.The processing of the Pilbara’s secondary deposits will therefore result in an overall reduction in operating costs, an increase in product yield from a plant, extend the life-of-mine and offer environmental benefits by reducing the tailings footprint and water usage.The quality and quantity of Australia’s secondary iron ore deposits and tailings are such that many other countries would judge these as equivalent to primary deposits. Furthermore, these tailings are already mined, available and liberated to such an extent that the recovery of a valuable product is highly economical in terms of capital expenses and operating expenses.CITATION:Steinberg, M, Graham, T and Gerards, M, 2015. Recovery of iron ore fines and ultrafines from tailings by using wet high-intensity magnetic separation – JONES WHIMS, in Proceedings Iron Ore 2015, pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By T. G. Joseph

ABSTRACT: The Canadian oil sands provide some of the harshest mining conditions in the world. Asoperations demand ever bigger tools, the toll on large mobile mining equipment is high, with structural life often half of that expected. Soft ground conditions predominantly lead to fatigue failure scenarios, poor stability, and inconsistent payload evaluations. These challenges are not solely a concern for Canadian oil sands mines; there are far-reaching implications for surface mining equipment in any poor ground-operating environment. This paper focuses on the basics of payload evaluation, motion response, and a simple estimate of structural life for haulers.

Jan 1, 2011

By Stanislatv Pawlowski

New, large sulphur deposits were discovered in Poland in 1953, the result of investigations by the National Geological Institute. All deposits occur in a widespread Miocene evaporite unit in the Carpathian foredeep. The gypsum underlying impermeable Sarmatian clays was altered to limestone and native sulphur where penetrated by hydrocarbons and bacteria. All deposits occur in Miocene structural uplifts. The early determination of the genesis of the sulphur deposits and their occurrence in elevated blocks led to an exploration program that successfully located new deposits.

Jan 1, 1978

By L. Tikasz

The primary purpose of ore hauling model studies is to capture the variability of the ore delivery ? stockpiling process in order to improve the estimation of equipment capacities and achievable throughputs. The operation of a mine-to-site ore delivery system is the subject of a number of challenges. Typically, ore is hauled by a given combination of trucks, conveyors and trains. In addition, ore loading, ore transferring to another means of delivery, stockpiling, reclaiming, and further deliveries involve many other types of equipment. The concurrent operation of all these units is scheduled; nevertheless, they are subject to planned maintenance and random breakdowns. To support our engineering design work on ore hauling operation, discrete event type models were built for each specific task. Then, due to recurring demands, an ore hauling library was gradually compiled. The now available model library allows fast and efficient simulation of various mine-to-site hauling arrangement, adaptable to various mining and mine construction operations (e.g. bauxite, iron ore, copper ore and coal).

Aug 1, 2013

By Björn Saxen

Outotec atmospheric Direct Leaching has so far been implemented for zinc production capacities of around 100,000 t/a. Lately, there has been growing interest for small scale direct leaching plants, producing circa 30,000 t/a of Zn. Such small leaching plants can provide extra front-end capacity in existing roaster-based plants and enable treatment of feed materials not suitable for roasting. In small scale plants the proven OKTOP® 9000 Direct Leaching reactors are not readily applicable, due the large size. For smaller installations a modular approach is proposed providing multiple advantages, such as reducing the construction time and amount of the site work required causing less disturbance to regular plant operation with reduced cost. In this paper, we present advantages that can be achieved by using modular OKTOP®C reactors and discuss also process design when connecting a small scale direct leaching process to an existing zinc plant. Also benefits of direct leaching expansion are presented.

By Tiejun Chun, Marcus Emrich, Jian Pan, Deqing Zhu, Vinicius Mendes

"Joint projects of studies of hematite acid pellet have been implemented to develop technological solutions for using Vale hematite pellet feed in Chinese palletizing plant. Beneficial improvements on the pellets quality were achieved by adjusting the blends composition and using new technology of pre-treating the blended pellet feed with HPGR (High Pressure Grinding Roller) on rotary kiln pellet technology. The drop strength of green balls increased from 3.4 to 6.0 times from 0.5m height, at the same time, the bentonite dosage decreased from 1.5wt% to 0.7wt%. The compressive strength of roasted pellets reaches 2500 N/pellet. The reduction swelling index of roasted pellets is below 15%.IntroductionWith the fast development of steel industry in China, the production of pellets has been further expanded. Pellets are used as a high quality charge for blast furnace and the annual output is around 80Mt pellets [1]. According to the developmental trend, sinter will be replaced by pellets due to the larger environmental impact of sintering plants when compared to pelletizing plants. For example, the specific CO2 emission in sintering process is around 2.5 times higher than in pelletizing process. However, the steel industry of China has been confronted with a serious shortage of domestic pellet feed due to the low iron grade of Run-of-Mine ore despite of huge reserves of iron ores [2]. Therefore, more pellet feed, mainly hematite, has been imported to make pellets."

Jan 1, 2011

By K. J. Maggs

The U.S. Bureau of Mines has investigated the chemical vapor deposition of diamond films on tungsten substrates. The effects of deposition parameters on the adhesion of the films was determined. The films were produced using a hot filament chemical vapor deposition system. Parameters investigated were substrate temperature and methane concentration in the feed gas. Film quality, morphology, and composition were characterized by scanning electron microscopy and Raman spectroscopy. Adhesion testing was performed using an indentation technique, and the results were quantified by relating adhesion to interface fracture toughness. Diamond films with well-faceted crystalline morphology with grain size greater than 1 µm had poor adhesion properties regardless of substrate temperature or methane concentration. Diamond films with smooth morphologies consisting of rounded clusters of small (<0.2 µm) diamond crystallites and amorphous carbon phases displayed much higher adhesion, although the conditions that led to the growth of these films are not understood.

Jan 1, 2010

By R. Pot

"IntroductionTHE PURPOSE of this paper is to discuss briefly the main logging and testing devices presently at our disposal, to point out some of their limitations, and to suggest possible improvements of the techniques.Some of the more important devices .are those that are used in:(1) Coring(2) Formation testing(3) Electric well logging(4) Radioactive well logging(5) Measuring of bottom hole pressures(6) Sampling of reservoir fluidsThe first four of these procedures are concerned with the well while it is in the process of drilling. The last two are carried out as soon as possible after a well has been brought into production and .at intervals during its life. My remarks will be concerned mostly with certain aspects of formation testing. The reservoir engineer is dependent on the information derived from these operations in order to obtain a clear picture of the conditions in a reservoir and to enable him to assess and forecast its future behaviour.Since any calculation is no better than the data on which it is based, not enough emphasis can be placed on the necessity for the testing and logging equipment to be of the highest quality and for the analysis of the results obtained to be thorough."

Jan 1, 1952

By Peter N. Calder

The orientation of planes of inherent weakness (joints) with reference to an excavation in rock is the critical factor determining stability. The purely frictional 'residual' strength remaining following the breakdown of initial cohesion is the only strength which can be counted on to resist sliding for the long term. A simple method of resolving driving and resisting forces in three dimensions along joint intersections 'undercut' by the excavation is presented. Contrary to the case of slope failure in soils, it is shown how significant changes in the slope angle sometimes have no effect on the degree of stability pre-sent in rock slopes. Wall control by reorientation of the slope, the use of cable bolts and water diversion are briefly discussed.

Jan 1, 1970

By Michael G. Zabetakis

The autoignition temperatures (A.I.T.&apos;s) of natural and synthetic lubricants in air were generally found to decrease with increasing pressure. Of the two types of fluids, synthetic and natural, studied in some detail, the phosphate esters had higher A.I.T.&apos;s at any pressure between 1 and 200 atmospheres than the mineral oils. Most of the A.I.T. data obtained in this study obeyed the relationship predicted by Semenov&apos;s theory of ignition.

Jan 1, 1962

By Jack E. Fraley

Magnesium oxysulfate cement has been specially formulated as a sealant in underground coal mines for reducing sloughing of shale roofs and coal ribs, for reducing air losses through block stoppings, for constructing sprayed stop-pings over approved jute cloth or metal lath, and for reducing combustibility of polyurethane foam. A standard spray machine (Mining Enforcement and Safety Administration (MESA) approved) was used for the underground testing. Our research shows that a 1/2-inch coating reduces shale and coal sloughing, reduces air losses through block stoppings, and prevents fire propagation through a metal tunnel lined with polyurethane foam. During the underground tests, excess mixing water was used to improve pumping the slurry to the spray nozzle. This was later found to increase shrinkage cracks in the cured coatings. Controlling excess water is important to an acceptable coating.

Jan 1, 1976

By Stanley M. Jarrett

Gentlemen, I am pleased to address this gathering of engineers and operation managers representing a large and important segment of the metal and nonmetallic mining industry. Since you know from the printed program that the theme of my paper is the furthering of safety in open pit mines, perhaps you will have guessed that I will also comment upon the image created in the public mind by the industry&apos;s safety record and the potential consequences thereof in national health and safety legislation. Operators of surface mines have some cause to congratulate themselves on the basis of figures issued by the national safety council which show that lost-time accidents per-million-man-hours in surface mining (11.18), is lower than that of all other mining. Moreover, the accident frequency in surface mining is only slightly above the median accident rate for all American industry (8.87). That is a good record.

Jan 1, 1972

By Phillip W. Holland

The U.S. Bureau of Mines has developed a mass spectrometer method for determining helium in the parts-per-million to 10% range to an accuracy of ± 1%. The method employs a mass spectrometer, an inlet system utilizing a chromatographic gas-sampling valve, and an activated coconut charcoal trap cooled with liquid nitrogen. Gravimetrically prepared standards of helium in nitrogen were used to demonstrate the linearity of the method over the concentration range of 10 ppm to 10.66% helium.

Jan 1, 2010

By Salustio s. Guzman

The standard .free energies of formation of tin chlorides were estimated with reviewed and estimated basic thermodynamic data, and measured reversible potentials for the disproportionation of tin dichloride into metallic tin and tin tetrachloride. Values for cºp, Sº, Hº?-Hº 298, -(Gº - Hº298) /T,.Hºf, Gºf, and log Kp are given in tabular form, these estimations are compared with estimations reported in the literature.

Jan 1, 1985