Search Documents

By Vijaya Bhushan Rao, Ali Semercioglu, Jason Redgers

Large diameter steel water tanks with high storage capacities impart heavy loads deep into the ground, generally requiring deep foundations to adequately support them. The use of ground improvement as a sustainable and cost effective alternative is tempting but the design of the foundations for such heavily loaded, thin-shelled structures have to meet several performance requirements such as bearing capacity, limiting the specified total settlements, typically limiting the radial differential settlement to 13mm over 10m along the circumference and dishing settlement from edge to center of 1/120 as per standard API 650 Appendix B as well as the mitigation of liquefaction induced settlement risk. Any inadequacy in the soil investigation, geotechnical design, or misrepresentation of stresses of the foundations may lead to serviceability compromise or potentially catastrophic failures. Therefore, the selection of the foundation is dependent on the availability of suitable ground report and the limitations imposed by operational requirements. Two such case studies are evaluated and compared in this paper, with tank diameters ranging from 41 to 106m in the Kingdom of Saudi Arabia, (KSA) which were founded on two types of soils and supported on deep foundations i.e., stone columns and bored cast-in-situ piles.

Oct 1, 2022

By A Seneviratne, Y Li, N Udugampola, X Ai, B Li

LoRa (Long Range) is a low-power, long-range wireless communication technology that has gained significant research interest for its potential use in multi-hop linear wireless sensor networks (LWSNs) for underground mines. These networks deploy LoRa-enabled sensor nodes in underground mines, together with LoRa repeaters placed along mine tunnels to relay sensor data to a LoRa gateway, which connects to a backend network for application-level processing. Since the packets generated by sensor nodes farthest from the gateway have to hop through many repeaters, their probability of successfully reaching the gateway is significantly lower due to the higher chance of packet collisions compared to sensor nodes closer to the gateway, resulting in a lack of network fairness for the sensor nodes. In this paper, we first present an algorithm to improve the fairness of a LoRa LWSN by grouping neighbouring nodes and adjusting the number of packet re-transmissions and transmission intervals for each group. Then, we demonstrate that the fairness of a simulated LoRa LWSN can be improved by approximately 500 per cent by applying our algorithm. We verify our algorithm with network simulations under different network traffic levels and grouping strategies, obtaining fairness improvements in each scenario. Our algorithm and results will pave the way towards developing highly fair LWSNs for underground mining applications.

Sep 1, 2024

By Jeff LeBlanc, George Gutierrez, Carl Pitzer

The Bay Park Conveyance Project was one of the largest microtunneling and rehab projects in the United States at the time of completion. The completed project conveys treated water from the South Shore Water Reclamation Facility located in Nassau County, New York, which currently discharges an average of 50 million gallons per day (MGD) of treated water into Reynolds Channel, to the Cedar Creek Water Pollution Control Plant (WPCP) ocean outfall pipe. The pipe carrying treated wastewater was installed approximately 20–60 feet below the surface. The treated wastewater is conveyed via microtunnel construction of a 2-mile long force main from the South Shore Water Reclamation Facility to an existing aqueduct under the Sunrise Highway, the rehabilitation of an 7.3-mile stretch of the aqueduct via sliplining, and construction via microtunnel of a 1.6-mile-long force main to connect the rehabilitated aqueduct to the existing Cedar Creek Water Pollution Control Plant (WPCP) outfall, which discharges and diffuses treated water three miles offshore in the Atlantic Ocean. This paper will review the Design-Build requirements, the chosen innovative solutions during planning for the micro tunneling portion of the project and review the microtunnel construction on the project.

Jun 23, 2024

By Miguel Ângelo Menezes, Carlos Alberto Alves Viana

O presente trabalho possibilita o entendimento e a análise dos processos de conformação a quente dos metais. Isto, pela validação experimental do modelo de Johnson-Cook, para descrever o comportamento dos materiais no regime plástico, para grandes deformações, às altas taxas de deformações e nas altas temperaturas. Um entendimento dos parâmetros do modelo, utilizando-se um método analítico numérico simples, rápido e confiável foi desenvolvido anteriormente pela linha de pesquisa em Conformação Plástica dos Metais na UNESP – Campus de Ilha Solteira, obtendo-se as constantes empíricas do modelo referido. É proposto nesse trabalho a validação experimental do método simplificado para determinação dos parâmetros empíricos do modelo de Johnson-Cook através de um ensaio de tração a quente, considerando as propriedades mecânicas dos materiais analisados experimentalmente e/ou de dados de materiais disponíveis na literatura. De maneira geral, os resultados experimentais foram satisfatórios para o aço AISI 1045 à temperatura de 500 ºC, ensaiado à taxa de deformação de 1000 s-1, quando comparados aos resultados teóricos previstos pelo modelo proposto por SCADUTO e MENEZES. Particularmente, foi possível evidenciar erros máximos de 1,33% para o parâmetro n, 13,15% para o parâmetro B, 295,00% para o parâmetro C e 4,14% para o parâmetro m.

Nov 11, 2019

By K Knorr

Desktop X-ray powder diffraction using a D2 PHASER equipped with fast linear detector was performed on several iron ore and mill scale samples. Data were analysed using cluster analysis and Rietveld quantitative phase analysis. The quantitative mineralogy of both materials could be established. Thus the input is provided for understanding the energy consumption and the CO2 emission during iron production. Furthermore, tabletop XRD allows to distinguish iron ore from mill scales and to quantify their mixtures.

Jul 11, 2011

By Jiachen Wang, Nan Wang, Yang Li

The close-multiple coal seam is an important component of China’s coal resources and plays a key role in total coal reserves. However, the overburden movement in the mining process of close-multiple coal seams is usually extensive, which is seriously affected by overmining. It is therefore essential to study the mechanism of roof breakage, the relationship between the shield and the surrounding rock, and the mechanism of overburden movement to ensure the safe operation and the efficient exploitation of close-multiple coal seams. This work first proposes a technical route for intelligent ground control. Second, the principle of cooperative control between the shield and overburden roof is revealed, and the shield support capacity calculation method is summarized. Third, the quantitative criterion for disturbance degree of key stratum (KSDD) is proposed based on the key strata theory. Finally, several intelligent evaluation and analysis systems have been developed in terms of overburden breakage and shield support capacity, multi-information analysis of ground control, and disturbance degree of overburden. The research results may provide an essential reference for the development of intelligent ground control in the mining process of close-multiple coal seams

Jul 1, 2023

By J Bohm, B Csoke, I Tarjan

In process technology, especially in coal preparation, it is often necessary to have a continuous knowledge of the average density of granular material in order to achieve both quality control and process control. The paper presents a new method and means supported by laboratory measurements for the rapid, practically continuous, determination of the average density of continuously supplied granular material through frequent sampling.

Jan 1, 1993

By Winfried Rosenstock, Carlos Orlandi

Along the Pacific West coast of Latin America there are several large operations of metal mining activities. To mention only a few: Chuquicamata in Northern Chile moving daily approximately one million t of copper ore and waste, Cerro Verde near Arequipa in Peru, or lanaccocia. Apart from the coal deposits in north-east Columbia it is mainly to deal with metal-mining, which has due to geographical reasons relatively high cash-cost. This sector of mining is traditionally severely depending on the world-market.There are reasons to believe that the world-market will remain on a low price level and some analysts predict that in general the price-level will continue on low basis for the next decade. The cash-cost factor becomes therefore even more important as it already is. The goldprice development during the year 1999 illuminates that market changes can quickly lead to a severe crisis which forces the shutdown of mines with cash-costs close to or above the present market price per ounce. The breakdown of the cash-cost shows, however, that there are ways to overcome even the crisis like it struck the low-grade open pit goldmines around the world. Especially hitherto the “Electronic Option” is the only solution as the possible reduction using advanced technology based on the application of electronic detonating systems and newly developed special ignition procedures. The electronic option will lead to tremendous cost reductions similar to the results of research operations Thiess Contractors, Brisbane, Australia have carried out in Australia in 1998 and 1999. The electronic option allows a comprehensive integration of side effects of the blasting process which in the past could not have been achieved so far. Electronic initiation can achieve secondary effects which have an additional and positive impact on the level of costs. Appropriate application can enhance the production of material which will reduce the primary crusher costs or even make a primary crusher operation obsolete.

Jan 1, 2000

By M. Kuchta

A linear integer programming (MIP) model to solve the long-and short-term production-scheduling problem for sublevel caving operations is presented. The MIP model is designed as a multi-time-period problem to provide monthly schedules that meet production, blending and sequencing requirements. One of the most important issues during the development of the MIP model was the requirement of sequencing between blocks. In this mathematical model, unique constraints that ensure sequencing of the production from sublevels are developed. A suggested method of handling a large number of variables is also given. The MIP scheduling model was implemented on a data set obtained from the Kiruna Iron Ore Mine located in northern Sweden. The initial MIP model implementation was successful and provided a solution that optimized resource recovery while meeting monthly and yearly production constraints. The scheduling results obtained based on the Kiruna Mine are further presented and discussed.

Jan 1, 2003

By Robert Horwood, Richard Harvey

The copper stave was a development of the Blast Furnace cooling system intended to utilise the high heat transfer properties of copper within a fully covered shell cooling solution. They were originally conceived as being able to provide a permanent cooling lining for use primarily in the higher heat zones of the Blast Furnace. Despite a large number of campaign successes around the world the everlasting concept has not proven universal, with some plants having suffered issues in two particular areas: stave bending (leading to water leaks at back of the stave) and stave wear (erosion on the hot face). Primetals Technologies have in the past been approached to provide assistance to a number of Blast Furnace operators who were experiencing operational issues with the copper stave furnace cooling systems of others. Through knowledge gained resolving these issues, and with the positive experiences of their own copper stave designs, Primetals Technologies have worked towards developing a new concept in copper stave design capable of providing a more robust solution to cope with the greater productivities of modern ironmaking. This paper will provide an outline to the concepts that have driven the design of this new technology.

Oct 1, 2019

By Roger Ferreira da Silva

O método de ensaio não destrutivo baseado na análise do ruído magnético Barkhausen (RMB) possibilita a obtenção de informações a respeito da microestrutura do material examinado e do estado de tensões presente no mesmo. Devido às particularidades do método, as medições devem ser realizadas mantendo-se constante a geometria entre a sonda e o objeto examinado, de forma a assegurar a confiabilidade das mesmas. Quando realizado manualmente, o processo de medição é demorado e sujeito a erros de posicionamento da sonda. Em trabalhos industriais ou em laboratório, esses erros podem resultar em interpretações incorretas, devendo ser reduzidos ao mínimo possível. Visando à redução do tempo de execução das medições e de análise e a eliminação de possíveis erros de posicionamento da sonda de inspeção, este trabalho propõe a automação do processo de medição de RMB em corpos de prova do tipo chapa. Compreende a construção de um dispositivo de movimentação XYZ acionado por motores de passo e do software “Plate Barkhausen”, com uma interface amigável, para controle da movimentação e da medição, além da análise dos dados.

Jul 30, 2018

By Guo Chen, Jin Chen, Jinhui Peng

In this study, the influences of the green evaluation variables on the characterization of microwave shaft furnaces were systematically investigated. These variables include: resource consumption, environment impact, production cost, processing time and quality of microwave shaft furnaces. A greenness evaluation index, evaluation system and evaluation model of microwave shaft furnaces were established. The analytic hierarchy process and fuzzy comprehensive evaluation were applied to the evaluation process. Resource consumption and environment impact had a statistically significant effect on the green evaluation of microwave shaft furnaces. The results indicated that green evaluation techniques can be applied effectively and efficiently to the process manufacturing of microwave shaft furnaces.

Jan 1, 2015

By D. Bessinger, J. Rabe, J. Zietsman, C. Coetzee, P. H. Lamont, J. Muller

The UCAR® CHILL-KOTE? freeze lining concept combines wall cooling with carbon and graphite refractories of higher thermal conductivities to ?chill? the refractory lining by transferring heat from the refractory lining. Effective sidewall water cooling, together with the efficiency of the heat dissipating conductive refractories, lowers the temperature of the lining to below that of the molten process materials. This causes a layer of slag and process metal to solidify or ?freeze? and form a protective ?skull? which completely coats the refractory hot face. Once formed, the slag skull insulates the refractories, reducing heat loss and protect the lining from erosion, chemical attack, thermal shock, and other stresses. The result: extended life and greatly improved refractory performance. The Ilmenite smelting process depends on the presence of a solidified slag skull to protect sidewall refractory material from chemical attach by molten slag. No known refractory material is able to withstand this corrosive material. To date, UCAR has not applied their Chill Kote ? technology in the ilmenite smelting industry. This paper revolves around the results obtained from conducting an ilmenite smelting campaign on a 500kW DC open-arc furnace with a UCAR designed refractory system. The purpose of this test was to establish the effects such a lining has on refractory wear and the reduction-smelting process. Proper thermo-couple management enabled the authors to monitor lining wear for the duration of the campaign. Prior to the pilot-scale campaign, modeling work was completed to evaluate the feasibility of applying UCAR® CHILL-KOTE? technology to ilmenite smelting furnaces. The successful operation of a pilot-scale furnace equipped with the UCAR® CHILL-KOTE? lining as well as concise modeling suggest that it should be a viable option to consider for an industrial-scale furnace.

Jan 1, 2007

By T Arena

To maintain copper recoveries and maximise production at the Sepon Copper Operation it is crucial to control the amount of copper entering the leaching circuit. This requires close control of blending of the multiple ROM stockpiles to achieve the desired head grade. Grade variability in the ROM stockpiles can lead to significant variation in the processing plant copper feed grade.Head grade sampling from the milling circuit at Sepon is complicated due to milling in leach solution to preserve the water balance. Copper is present in both liquid and solid forms and copper in the added milling solution has to be accounted for. This leads to difficulties in manual head sampling which also introduces delays due to sample preparation and assay turnaround. On-stream analysis is complex because of the solution and solid copper and the need to account for recycled copper solution.This paper describes the complexity of feed grade management at Sepon and the application of on-belt analyser technology to assist in the control of copper metal throughput.

Aug 8, 2011

By M Sparrow

The Victoria Park Tunnel project is an inner-city alliance project in central Auckland, New Zealand. The existing two-directional viaduct will be modified to single-direction flow, and a new northbound 440 m cut and cover tunnel will be constructed beneath Victoria Park. Three-dimensional (3D) visualisation media were used to communicate key design innovations to stakeholders and the general public. The 3D visual material has proven a useful tool for informing motorists of a new safety barrier method adopted for traffic management.This presentation will explain how 3D visualisation was incorporated in the project and will showcase the 3D visualisation media created for the project.

Mar 8, 2011

By D. N. Hedges

This paper discusses the actual recovery and installation of a longwall in a bituminous coal mine in western Pennsylvania. The coal bed mined is in the Lower Freeport seam, which averaged 1.07 m (42 in.) in height locally. Drainage from the mine is about 13.25 ML/day (3.5 million gal per day) of water. This water deteriorates the mine's predominately fire clay bottom making it extremely difficult to move equipment. Support removal is accomplilshed by pulling the 5.44 t (6 st) shields out under their own hydraulic power and transporting them by track 8.05 km (5 miles) to the next longwall panel. This paper also discusses the changes that will be made to aid in the succeeding longwall recoveries and installations.

Jan 1, 1985

By Michel Bustamante

The Arbre viaduct, 200 metres long, is the most important structure on the Belgian portion of the High Speed Train line between Paris and Brussels. The particular geotechnical conditions of the soil with carboniferous limestone affected by karstic phenomena, has prompted the designer to found the viaduct on systems of high capacity vertical and batter micropiles. The design of the working micropiles was validated by full scale tests performed on instrumented micropiles. The size of the structure and the deformation criteria to be met when HS trains are crossing the viaduct, together with the lack of references for such innovative structure, called for monitoring the movements of the piers as soon as the link was open to traffic. The authors report on the results of loading tests on micropiles and the results of settlement structure monitoring for a period of 4 years. Settlement of the foundation is estimated taking into account the group effect.

Jan 1, 2002

By Adrian Fleming

Adrian Fleming is Executive Vice President of Exploration for Golden Star Resources Ltd., Denver. Adrian is an Australian who graduated in 1973 with an honors degree in geology from Newcastle University, New South Wales. His extensive international experience has spanned exploration, project development, and operations for both large and small companies in Australasia, Southeast Asia, North and South America, and Africa. Adrian has been with the Golden Star group of companies for four years and he is responsible for all exploration activity. ABSTRACT Golden Star acquired the rights to the Omai prospect in 1985 at a time when the country of Guyana was out of favor with the exploration fraternity. Subsequently in the late 1980s and early 1990s, Golden Star acquired exploration properties in Suriname and French Guiana well ahead of its competitors. Golden Star's strategy entailed identifying windows of opportunity and aggressively pursuing them. We also recognized that the Guiana Shield hosted a significant area of highly prospective greenstones which were comparable in metallogenic potential to similar terrains in eastern Canada, western Australia and west Africa. The geological skills Golden Star developed and the exploration techniques employed to explore deeply weathered rocks are described. The paper highlights the key elements of Golden Star's strategy and illustrates how some of the milestones reached by the company led Golden Star to establish an enviable portfolio of gold and diamond properties in the Guiana Shield.

Jan 1, 1998

By Chris Groccia, Damodara R. Chinnasane

Vale is in the process of resuming mining in the lower 810 ore body (810 OB) below 4130L at Copper Cliff Mine – South Side. Production in the lower 810 OB had continued until it was temporarily ceased in 2017 to allow for the execution of activities associated with Copper Cliff Mine Phase 1 project. While mining the stopes in both the lower and mid part of the 810 OB, a seismic response was experienced that resulted in rockbursts and challenging mining conditions. The majority of the rockbursts experienced in the past were associated with stopes mined in a bottom-up mining sequence under a diminishing pillar situation between 3350L and 3540L. The current mining plan is comprised of both top-down and bottom-up mining fronts using a center-out chevron sequence of long hole open stopes to manage induced stresses. Numerical modeling assessments have been carried out to forecast the response of the rock mass due to the planned mining. Seismicity and stress induced damage surrounding excavations are anticipated, and areas requiring extra attention have been identified. A tactical approach is being used to prepare the area for production, including replacement of ground support elements that are damaged or have insufficient residual capacity, and installation of dynamic support in areas anticipated to experience bulking and/or dynamic loading that would exceed the current support system’s capacity. A series of monitoring programs are being put in place to confirm current conditions, and to monitor the response of the rock mass to proactively implement ground control tactics should the need arise. This paper provides a summary of the approach used to forecast, monitor, and manage the behavior of the 810 OB rock mass response to continued mining at depth.

Apr 26, 2022

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES

Lithium-ion battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12 V, 24 V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicated that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

May 4, 2023