Search Documents

By E. Busse

"Heath Steele Mines Ltd. operates a lead-zinc-copper mining and milling complex in New Brunswick.• During the past seven years, as ore reserves increased, the mill capacity was first expanded to 1,600 tpd and then to 3,000 tpd. In the last expansion, instead of building a completely new 3,000-tpd mill, or adding to existing installations, Heath Steele retained service facilities, buildings, ore bins, Jab, etc., and removed and replaced almost all existing process facilities. Requiring a complete mill shutdown, the expansion had to be carried out in minimum time. Also, new equipment had to fit into existing space. Critical path networks of the project were prepared, a tight schedule for construction was mapped out and progress charted daily to detect problems before they could interrupt the schedule. Heath Steele supervised the purchasing, handling and storage of new equipment, maintained liaison with the engineering contractor and became a sub-contractor, using its own staff to install all flotation equipment and process piping. The 1,600-tpd installation was dismantled and a 3,000- tpd unit was successfully put onstream in 5 months - on time and within budget. One benefit stemming from the expansion: production increased 87 per cent while operating and maintenance labour rose only 8 per cent."

Jan 1, 1972

By A. B. Walker

The effects of the injection of dry limestone additives into boilers for the sorption of sulphur dioxide have been studied in pilot and full-scale systems. The effects of such injections on boiler mass particulate emissions as well as collectability characteristics of the fly ash and reaction products are presented. Implications of the effects on the design and economics of particulate collectors, in particular electrostatic precipitators, are discussed.

Jan 1, 1971

By B. S. Kim, Y. D. Kim, T. S. Kim, T. B. Kim, H. J. Chae

"The Nd-Fe-B scrap was placed in Fe crucible with pure Mg in an Ar atmosphere, and the scraps were melted using an induction heating method. The effects of experimental parameters such as melting temperature (range of 993K to 1073K) and holding time (15min-600min) on the ability of extraction were investigated. The microstructure and diffusion layers were analyzed by Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS), and the constituent phases were characterized using XRay Diffraction (XRD). Diffusion of Nd through the Nd-Fe-B scrap into liquid Mg was described, and the diffusion coefficient of Nd in liquid Mg was estimated.INTRODUCTIONNd-Fe-B magnets are usually produced either from comminuted melt-spun ribbons as bonded magnets or hot pressed bulk magnets, or by sintering in conjunction with prior green compaction in an applied magnetic field (Sagawa et al., 1984). These magnets have been widely used for various electromechanical and electronic devices such as voice coil motors (VCMs) and magnetic resonance imaging (MRI) (Samardzija et al., 2012; Matsuura et al., 2006). The production of the Nd-Fe-B magnets is increasing by about 20% per year because of their excellent magnetic properties. However, the expansion of Nd-Fe-B magnet market induced a concern for the scarcity of Nd at the aspect of natural resource. Therefore, the development of an effective recycling process for Nd-Fe-B magnet scraps is an extremely important issue from the viewpoint of resource and energy conservation. Several recycling processes for the Nd-Fe-B magnets have been proposed (Uda et al., 2002; Lyman et al., 1993]. It has been reported that the best separation of rare-earths from the Nd-Fe-B magnets is obtained by sulfuric acid dissolution followed by precipitation of recyclable rare-earth salts. However, this process can make a large amount of waste water including dangerous solutions. Recently, (Xu et al., 2000) have reported a technique to extract Nd from 18Nd-72.4Fe-0.9B-1.82Pr-5.3Dy (wt.%) magnet scrap by using liquid metal extraction (LME) processing. However, these techniques seemed to be difficult for application, because the scraps consist of an infinitesimal amount of other minor elements (Pr, Dy, Cu, Al and Tb), and these minor elements can make a new intermetallic compounds with Mg. Also, some oxides or the plated Ni metal can be preventable to reaction between solid-liquid (S/L) interfaces. For these reasons, the substantive reaction mechanism between Mg and Nd-Fe-B scrap is not clear. In this study, the simple composition of 33Nd-66Fe-1B (wt.%) magnet scraps were prepared using an induction melting process. The effects of the experimental parameter on the diffusion properties between Mg and scraps were investigated to determine whether these methods could be used in industrial application in a liquid metal extraction (LME) process."

Jan 1, 2012

By D. C. Martin

Stability analysis and design of open pit slopes is generally based on an assessment of rock cores and rock exposures on surface or in underground workings. Until recently, core for such assessments has been readily available from exploration drilling programs. In recent years, many exploration programs have reduced the amount of coring and rely more heavily on less expensive rotary or percussion drilling programs where drill cut-tings are sampled for geological evaluation and assay. This paper describes a technique whereby costs of the geotechnical investigation are reduced by using rotary percussion drilling information to assess geotechnical properties of the rock mass. A limited number of core holes are required to establish basic relationships between the mechanical properties of core and the characteristics of the percussion chips. These properties are used as a basis to extrapolate the coring information to encompass the entire area of the rock mass for which percussion drilling information is available.

Jan 1, 1990

By Martha Gellner, Lutz Wuschke, Hans-Georg Jackel, Urs A. Peuker

"Electric vehicles are an alternative to the existing combustion engine driven cars. According to the EU Battery Directive a substantial recycling rate of at least 50 wt.-% has to be met for aged batteries since 2006. Existing recycling techniques are based on energy intensive pyro- and hydrometallurgical process, which are not able to recover all components. Aluminum and lithium for instance are slagged. The EU-Project “ABattReLife” investigated possibilities for a mechanical processing in order to create a sustainable process and a closed material loop from grave to cradle. After a sufficient liberation of the Li-ion batteries, components like the doped carbon black fraction (mainly lamination of electrode foils), the separator foil and the housing material can comparatively easily be separated from the other components by screening and air sifting. The remaining mixture consists of anode and cathode foils which have a similar free-settling ratio and are more difficult to separate from each other. A second comminution and compaction step modifies the particle size and shape as well as the degree of delamination. These changes influence the density of the electrode foils in order to improve the separation efficiency. Yield and purity of the generated metal concentrates were parameters to show if the separation was successful. The specific energy consumption for the different methods of processing was estimated in order to benchmark the cost-benefit ratio for each one.The studies have been accomplished with a zig zag sifter (model TUBAF), a hammer mill (model HM 340 Jehmlich) and with a Petkus-Sifter. Finally a process flow sheet was developed for a Li-ion battery recycling plant in pilot scale."

Jan 1, 2016

By P. N. Calder, D. B. Apel, S. D. Butt

Mine-wide (MW) microseismic systems use widely spaced transducers to determine the source location and parameters of stronger microseismic events, while high frequency (HF) systems use fewer transducers to monitor local areas for the weaker events that can precede stronger events. Previous monitoring at the Creighton Mine indicated that an HF transducer located 120 m away from an active stope recorded two types of activity in response to production blasting: the first occurring at the same time as the production blasts and associated with the passage of the direct seismic waves from the blast through the local area, and the second occurring several hours later and associated with the arrival of a slower moving stress change through the rock mass (which was identified by the mine’s MW system). Interpretations of locally increased stress levels, based on analysis of the recorded HF events, correlated with the nearby occurrence of two strong seismic events. These results were applied to a similar monitoring trail at the Kidd Creek Mine where the transient stress changes induced by several development blasts were monitored. It was observed that increases in HF activity corresponded with the occurrence of MW events near the transducer location, and that fewer HF events were recorded the longer this occurred after the blast. Local geological features appeared to influence the number and occurrence of both HF and MW events.

Jan 1, 2000

By A. Collings, A. Farmer

Power ultrasound may be used in the processing of mineral suspensions to clean the particle surfaces of oxidation products and fine coatings, mainly through the large, but very localised forces, produced by cavitation. This effect may be utilised in lowering the level of iron contamination in silica sand used for glass making, in improving the sharpness of electrostatic separation of heavy mineral concentrates, in shortening the time of leaching of minerals and in improving the selectivity and recovery of flotation processes. Parameters affecting the efficiency of these processes, such as input power and levels of reagent addition, are discussed. In particular, we present data showing the relationship between power input and the particle size of surface coatings removed, which can be explained by the Derjaguin approximation for the energy of interaction between a sphere and a flat surface. Pilot scale studies, using commercially available components, are currently being used to assess process viability and will be compared with laboratory scale results.

Jan 1, 2003

By E. L. Chanturiya

During the mineral processing of pyrites sulphide ores of some deposits of Russia loss of gold with tailings and pyrite concentrates amounts up to 40%~90%. The problem of selective allocation of gold-bearing pyrite is crucial. There are 4 mineralogy-technological groups of pyrite determined in copper-zinc sulphide ores, based on the increase of contents of gold in pyrite. The gold associated with group 4 pyrite contents of 85% the total mass of gold found in the pyrite. The flotation behaviour of the enriched fractions of pyrite (98%), of the allocated from the ore of Gay deposit, were studied essentially in various conditions ?? and the charge of Butyl xanthogenate of potassium (ButX). Some products of selective pyrite flotation were investigated by methods of scanning electronic microscopy, energy-dispersive and X-ray spectral microanalyses, definition of specific resistance and thermoelectric moving force.

Jan 1, 2014

By T P. Medhurst

In many cases mine design is the most important driver of the profitability of a mining project, however to reach an æoptimumÆ mine plan many compromises have to be made. Some of the fundamental profit (and loss) drivers relate to stoping methods and stope design parameters. Inevitably trade-offs have to be made between the stability of underground openings, ground support costs and production efficiency. This paper looks at the role of geomechanics in the mine planning and design process. The concepts of æcontrollable lossesÆ and æuncontrollable lossesÆ are developed as a means of partitioning ground control costs. A stope design example is given which provides a method of examining mining costs, and includes a decision making element in order to quantify geotechnical impacts and select stope dimensions. The method also provides a general framework as a means of balancing ground control costs against maximising returns from an underground mining project.

Jan 1, 2000

By Liow Jong-Leng

A survey of the interactions of large gas bubbles formed from top and bottom injection of gases into melts was carried out. Spherical cap bubbles were found not to produce much splash when they break through the bath free surface except for that formed by plunging of the-spout at its edges. In contrast, the bursting of balloons produces cavities which give rise to liquid jets being ejected from the bath free surface. The position of the balloons relative to the bath free surface is an important parameter in the formation of the liquid jet. It is found that the interactions of multiple bubbles close to the free surface is important in determining the splash behaviour of gas injected systems.

Jan 1, 1996

By M. Evertsson, M. Johansson

"In minerals processing control is vital to increasing performance and output of a plant. Model predictive control (MPC) is one of the most effective control strategies used in process industry. Sbárbaro (Sbárbaro and Del Villar, 2010), Asbjörnsson (Asbjörnsson, 2015), and Légaré (Légaré et al., 2016) have for example highlighted the possibility to simulate, develop and tune control systems using plant simulators within minerals processing. In more recent years the use of model predictive controllers have increased, and many process industries now utilize more advanced control methods to regulate their processes, raising the question regarding how to, build, test and verify a proposed control solution successfully. In this research, a linear model predictive controller is formulated and applied to a simulator of an existing tertiary crushing circuit. The circuit has in previous work by Johansson (Johansson, 2017) been modeled in MATLAB Simulink and calibrated relative plant data to an average error of less than 10% over 8 hours of production. The work demonstrates how to formulate the controller model structure to describe conveyor belts, storage components, screens, crushers, and control objectives for a minerals processing circuit. The work illustrates how to apply and successfully evaluate possible upsides in a circuit. The advantage of a crushing circuit simulator is that it can be configured, tuned and modified in any possible way, which is of great benefit to developers and engineers. Additionally, examples of how to use estimated measures to improve the performance of the plant are demonstrated. The control performance is finally evaluated for three different controller configurations."

Jan 1, 2018

By W. A. Bain

"AbstractProduction from the Excelsior Reservoir has amounted to approximately one million barrels. This production has caused a 'Pressure •drop of 10 p.s.i. from the original pressure of 1,245 p.s.i.g. Volumetric balance calculations indicate that the pool as being produced by a water drive whose strength is •probably unsurpassed in Western Canada. It has also been shown by 'unsteady state' calculations that the reservoir will still be above the saturation pressure of 915 p.s.i.g. at the time of depletion. The average permeability of the producing formation is approximately 1,000 millidarcys and, consequently, well draw-downs are very low. The field is essentially a bottom-water drive and calculations have shown that gravity drainage will greatly assist the recovery of oil. Water flooding data on several cores •have placed the flushing efficiency at •approximately 50 per cent, which indicates a recoverable oil-in-place of 17.7 million stock tank barrels. Calculations and field data indicate that the MER for the early life of this field is probably as high as 8,000 to 10,000 stock tank barrels per day.IntroductionTHE EXCELSIOR NISKU oil reservoir is located about twenty miles northeast of Edmonton. The field was discovered in November, 1949, by Imperial Excelsior N.o.1 well, in Lsd. 13, Sec. 3, Twp. 56, R. 22, W. 4, at a depth of 3,850 feet.Since discovery, development has continued on a 40~acre spacing pattern. At the end of 1951, drilling over approximately 80 per cent of the estimated productive area of 1,680 acres had established 32 we1ls capable •of production. The field •has been fairly well delineated by dry holes on all but the eastern flank ."

Jan 1, 1952

By S. H. Lau

Rapid 3D characterization of multiphase mineral particles in a variety of mineral processing applications is described, including: mineral liberation analysis, grain size, mineral exposure analysis, particle damage, and pore network structure for fluid flow simulation in heap leaching. While micro X-ray computed tomography systems (microCTs) have been used for many years, industrial adoption is limited due to a variety of reasons, including insufficient resolution, the general lack of imaging contrast to differentiate different mineral phases within a multiphase mineral particle and the lack of automated 3D mineral processing software. For example, resolution with industrial CTs and desktop microCT is of the order of tens of microns to a few microns at best, depending on specimen size and CT configuration. We describe a novel lab-based X-ray microscope, XRM, which overcomes these resolution and contrast limitations, notably as the industry is going towards finer grains and more complex ore bodies. Using lens-based optics and detectors (similar to its XRM counterpart in synchrotron beam lines), resolution of the lab based system is in the submicron range with contrast better than conventional microCTs. Hence, visualization, differentiation and segmentation of most mineral phases of interest to the industry are now feasible. Coupling these high resolution and high contrast tomography images with a suite of customized 3D segmentation algorithms and analysis software, applications in mineral liberation analysis for process control, particle damage assessment and other mineral processing applications can be achieved. This non invasive 3D technique which requires relatively little sample preparation is currently being considered for coal, industrial minerals, and base/precious metal ores, complementing existing microscopy techniques such as QEMSCAN and MLA for a variety of applications

Sep 1, 2012

By L. M. English

In the past 30 years, the research arena has changed significantly in all fields, mining included. The relative representation of the topics of research, how the research is performed, and who has performed the research have all changed significantly over these decades. Although there are a lot of subjective ideas concerning these changes, and there is a fair amount of anecdotal "analysis," there has been no actual study of these trends to verify the facts. The period studied is divided into six five-year periods for the purposes of comparison. Some of the trends analyzed are as follows: ? Co-authorship ? Research areas ? Research sponsors ? Cooperative efforts

Jan 1, 1995

By R. Boom, B. Kraaijveld, H. Kuntzel, Y. Meteleva-Fischer

"Alloying refining with rare earth elements followed by acid leaching was examined for the potential of upgrading of metallurgical grade silicon. Microstructure study of silicon alloyed with small additions of rare earths showed behavior relatively similar to the influence of calcium addition. After alloying with neodymium the phosphorus content was detected in various intermetallic silicides containing neodymium and iron. The content of lanthanum and neodymium in refined silicon was by several times lower than that of aluminium and calcium. Alloying with lanthanum and neodymium at smaller additions than calcium reduced the phosphorus content down to the same level. The efficiency of lanthanum and neodymium in removal of boron and phosphorus at the 1-2 wt% of their additions and their low solubility in silicon make the alloying with these metals followed by acid leaching an attractive option for the refining route of metallurgical grade silicon up to solar grade.IntroductionA striving for a cheap ""green"" energy directs the research interests in silicon solar cells towards new efficient refining routes for metallurgical grade silicon (MG-Si, -98% purity). The silicon price determines up to high extent the solar module's price, so that cheap and efficient metallurgical process is awaited. The research challenge is to fulfil the purity requirements of solar grade silicon (SoG-Si, 6N) by competing with the energy-consuming and environmentally unfriendly Siemens process. Most difficult impurities to remove are boron and phosphorus, so technologies dedicated to their efficient removal attract an attention of industry and academia.Alloying refining (also known as solvent refining) is one of the most promising refining options, which is based on a principle of solid-liquid extraction using limited solubility of impurity elements in solid silicon [ 1]. Various elements were proposed for alloying refining: aluminium [2], calcium [3], tin [4], iron [5], copper [6] etc. The attractiveness of the alloying refining is in decreasing a melting point of the metal mixture and an affinity of the alloying element to the most harmful impurities, especially to boron and phosphorus. However, the difficulties are still faced due to self-solubility of the alloying elements, their low affinity to boron and/or phosphorus, silicon losses and necessity of removal of the silicide impurity phases in an additional step, using acid leaching [7], fractional melting [ 8] etc."

Jan 1, 2013

By Lars A. Bergstrom

High-voltage direct -current transmission is a relatively new technology. The successful development and operation of AC/DC converters, capable of handling large power blocks, have made HVDC transmission generally accepted by utility engineer s and planners around the world. HVDC technology still has significant development potential and, as a result, it is expected that equipment costs will escalate at a substantially slower rate than those of conventional AC equipment. This development will also result in still more compact terminal stations. This paper reviews two modern HVDC installations. In Zaire in Africa. a 1700-km overhead DC line rated at 500 kv, will supply power to the copper mining district in the Shaba region. Another HVDC link connects Norway and Denmark through a submarine cable rated at 250 kv. This is the longest HVDC cable in the world, 127 km, and the water depth , maximum 530 m, is also much greater than for any previous similar cable. The reasons for selecting HVDC are discussed, and the design and layouts are presented.

Jan 1, 1978

By Akira Yazawa

The similarities and differences in copper, nickel and lead smelting processes are discussed based on the sulfur-oxygen chemical potential diagrams and the free energy minimization assessments using a thermodynamic software. The prominent features of copper smelting are ascribable to the fact that copper has a strong affinity for sulfur but weak for oxygen and the liquid phase immiscibility between Cu and Cu2S. During the oxidation of sulfides, nickel metal is not stable except at temperatures higher than 1500°C, well miscible with its sulfide, and is oxidized more easily than copper. Metallic lead looks as stable as copper during the oxidation of the concentrate but Pb and PbS. are much more miscible with each other and the vaporization loss is considerable. In the reductive smelting of oxides, the effects of oxygen potential and temperature on the copper contents in slag are not significant due to the monovalent character of copper and the reduction of copper content in slag is not easy in practice. The effect of the slag compositions on the oxidic metal contents of slag is much more significant for lead than either copper or nickel. Due to the immiscible nature between Pb and Fe, high grade lead bullion is easily obtained and lead is more tolerant to impurities.

Jan 1, 1998

By Verya Nasri, James Sullivan, Alex Varas

"INTRODUCTION Many major cities in the United States have a combined storm water and sanitary sewer network. Regular rainfall overwhelms the system capacity and results in millions of cubic meters of untreated sewage being dumped into local waterways. One legally mandated solution includes several kilometers of large diameter shallow or deep rock or soil tunnels, a pump station as well as associated collection sewers, diversion structures and drop shafts. In this paper, the basis for design of different system elements including the drop shafts and pump station is explained in detail. Common construction methods used for different type of shafts including tangential vortex and baffle plunge, and also pump station alternatives comprising cavern or various shaft configurations are discussed. DIFFERENT TYPES OF PUMP STATIONS The dewatering pump station serves as the heart of any deep CSO tunnel system and is critical to the goal of reducing CSOs by providing a controlled release of the stored tunnel volume to the wastewater treatment plant. As the major mechanical component of the project, the station will require the greatest attention by operations and maintenance staff. Designing a durable and easily operated pump station requires addressing some major challenges, including the following: • Longevity – equipment, materials of construction, and station environment • Controlling odors • Safety for operators and maintenance personnel • Easy access to equipment • Protection from hydraulic surges Location. Owners face a fundamental decision relative to the location of the pump station, which will affect how these challenges are addressed. The pump station can be built within the tunnel launch shaft or within its own dedicated shaft. This decision is driven by cost and schedule. Use of the tunnel launch shaft may provide owners cost saving opportunities by not having to construct a separate pump station shaft. However, this will likely extend the pump station construction as much as two years until the tunneling has been completed. Furthermore, delays to the tunneling operation would delay the pump station construction work, potentially leading to delay claims. For this reason, it has been more common to utilize a separate pump station shaft on recent CSO tunnel projects (Nasri et al. 2015)."

Jan 1, 2016

By David G. Adam

Syncrude Canada Ltd. is currently mining over 120 million tons per year of overburden and oil sands to produce 40 million barrels per year of synthetic crude oil. Production increases are planned. This paper reviews the technical and economic assessments of feeder breaker applications in both ore and waste mining which led to an extensive testing and development program and finally to the procurement of full scale production equipment.

Jan 1, 1985

"The first 90 years of the last century generated a considerable volume of technical literature on the subject of grinding mill power and its prediction. It is therefore surprising that during this time there were no published models for predicting grinding mill power draw which were validated using a wide range of comprehensive industrial scale data.Notwithstanding this lack of data, the majority of models placed limited emphasis on the internal dynamics of mills and relied on simple assumptions which considered the charge to take up a fixed position and shape.Laboratory based studies (Liddell, 1986), and industrial data (Morrell, 1993), showed that these assumptions did not hold over a wide range of operating conditions, and brought into doubt the ability of the (then) existing models to accurately predict grinding mill power draw. Furthermore no model treated AG,SAG and ball mills as a single class of devices whose power draw could be predicted with the same equations.Through a detailed investigation of the charge dynamics, coupled with a large data base of industrial mill power draws, this situation was rectified by the end of the century, by which time a model had been developed and validated, which accurately predicted the power draw of all wet tumbling mills. This paper describes this model and reviews some of the earlier attempts at mill power modelling.INTRODUCTIONThe early 1900?s saw the beginnings of published papers which tackled the problem of what influenced the power draw of tumbling mills and what equations (models) were suitable for predicting power draw. This interest continued for the rest of the 20th century and the literature contains many papers that attempted to satisfactorily answer these questions. A common and disappointing theme in the majority of them, however, is the distinct lack of suitable experimentally derived power draw data. This deficiency consequently limited the practical application of many of the attempts at modelling mill power draw. Prior to the early 1990?s some limited data on the power draw of grinding mills in the literature can be found, but as Harris et al (1985) remarked they are ?... too frequently unusable simply because one or more essential variables have been omitted?. The absence of published results, from vigorous experimental testing of the various models, has resulted in a general lack of evaluation of the validity of assumptions and hypotheses that such models contain. Harris et al (1985) however, did make some efforts in attempting to evaluate the performance of various power prediction equations and in so doing further developed a semi-empirical one of their own. However, in using manufacturers? published data, which themselves were undoubtedly generated by proprietary equations of unproven validity, they probably succeeded in generating little more than a consensus of the various errors in these models."

Jan 1, 2003