Search Documents

By A. B. Needham

Graphite is a raw .material of considerable importance in both waxy and peace. Two types of graphite, classified according to particle size as flake and fines, are used, but the former is in much greater demand. The principal wartime use of graphite is in the manufacture of crucibles for melting brass and special alloys of copper and steel. Other uses in both peace and war are as lubricants, for foundry facings, and in paints, electrodes, batteries, motor and generator brushes, and a variety of other commodities. . This paper describes the operations of the Southwestern Graphite Co. of Los Angeles, Calif., which produces both flake and fine graphite from a property in Burnet County, Tex.

Jan 1, 1946

By Adam Bezuijen, Tiago Gerheim Souza Dias

"The construction of mechanized tunnels in soft ground has evolved significantly over the last 20 years, especially in the control of the face pressure and the closure of the soil-lining void to reduce the induced settlements. On the other hand, several mechanisms of the TBM excavation cycle are still not taken into account for routine design calculations, such as the increment of water pressures in front of the tunnel face, the flow of excavation fluids around the shield, the dynamic equilibrium between the grout pressures and the excavation convergence, among others. This paper discusses specifically the issue of face pressures and how several mechanisms, which are routinely not considered, can be easily verified and incorporated into the state-of-practice of design. INTRODUCTION The stability of underground excavations is traditionally assessed through analytical solutions based on the lower bound theorem of plasticity (Atkinson and Potts 1977; Mühlhaus 1985) or the limit equilibrium method (Anagnostou and Kovári 1994; Messerli et al. 2010). These methodologies depend on the tunnel geometry, certain ground parameters and the support pressure. When conventional construction methods are used, the internal support pressure is an abstract representation of the combined effects of partial excavation, ground reinforcement, and the different support elements. The use of closed-face tunnel boring machines (TBM) changed this perspective, as the magnitude of pressures acting on the excavation boundary could be controlled in a more direct way. In front of the TBM the ground is excavated as the cutterhead rotates and the cutting tools scrape the ground from the tunnel face while additives are injected to condition the material. Water, polymers, bentonite, and foam can be used as additives under different conditions (Thewes et al. 2012). The loosened ground with additives, herein referred to as the mixture, flows through the openings at the cutterhead and into the excavation chamber. This mixture is kept pressurized to support the face."

Jan 1, 2016

By M. Olper, M. Maccagni

"The crude zinc oxides (CZO) produced in any thennal process dealing with EAF dust also contain lead, cadmium, and a considerable amount of halides (chlorides and fluorides). The high halide contents make these crude zinc oxides less and less attractive, both technically and economically, and a further refining procedure is nece'ssary to meet the zinc and zinc oxide market requirements.Hydrometallurgical techniques commercially used to dehalogenate the crude zinc oxides are not effective enough to upgrade the crude zinc oxides to the required specification for their direct use in the traditional sulphuric electrolysis by primary zinc producers.The EZINEX® PROCESS has solved the problem of the halides contained in the crude zinc oxides. This process is the only proven technology electrowinning zinc from a chloridebased electrolyte in a conventional cell house. This paper discusses the process economics taking the data from feasibility studies of different size commercial plants."

Jan 1, 2000

By Tamás Megyeri, Dániel Borbély, Vera Szánto, László Kovács

"Upon completion, the Bátaapáti deep underground radioactive waste repository complex (National Radioactive Waste Repository - NRWR) will provide safe final disposal for low and medium-level radioactive waste from the Paks Nuclear Power Plant in Hungary. The waste emplacement is in progress and one of the main concerns related to the development is ensuring a feasible plan is in place for permanent repository closure. Detailed hydrogeological observations and safety assessments revealed that the clay filled fault zones penetrated with the access tunnels play determinant role in the long-term confinement performance of NRWR, so they need to be plugged. Detailed mechanical analysis and numerical modelling of the tunnel constructed through a fault zone is presented here to gain a better understanding of the rock mass and rock support behavior. The effect of stress reflection is demonstrated and its consequences are described in detail. A recommendation is given for tunnel support design in such conditions. INTRODUCTION Crossing fault zones is a challenging task during tunnel construction and can lead to failure if not properly accounted for during design and construction. These failures are can be caused by high water inflow or stability loss of the rock mass surrounding of the tunnel (examples can be found in CEDD, 2015). The prediction of the magnitude and development of displacement has a considerable impact on issues during tunnel construction. Changes of rock mass stiffness or structure ahead of the face, to a great extent influencing stresses in the vicinity of the tunnel and thus deformations (Steindorfer, 1998). Further research with numerical simulations was carried out, and the qualitative and quantitative evaluation of displacement vector is presented in (Grossauer et al, 2005). The concern associated with crossing fault zones was considered during the design of the Bátaapáti deep underground radioactive waste repository complex (NRWR) in Hungary. In the case of NRWR project, the fault zones have an impact on maintaining the stability of the surrounding rock mass as well as the final sealing of the repository. As part of the final closure design, a complex numerical modelling program was completed to gain a better understanding of the mechanical behavior of the rock mass and the monitoring observations during construction. Even though the need for the presented study is closely related to the NRWR project, the results can be used in any project related to fault zone crossing. The methodology used to better understand the impact of crossing fault zones for the NRWR project is presented in this paper. First the project background is introduced including an overview of the underground facilities, the aim of the repository, and the construction experience gained from the first crossings of the fault zones. After that the in-situ and laboratory testing is summarized. The numerical modelling methodology is detailed in the next section. Not only the outcome of the model is presented, but the results are compared with the experience and observations made on site. Since a good agreement is found between the actual and the modelled behavior, the conclusions are based on the validated result. To fulfill the aim of the paper, the stress reflection concept is introduced to explain the mechanical behavior of the fault zone and the rock support; furthermore straightforward suggestions are made for rock support design."

Jan 1, 2016

"Real-time, on belt analysis of minerals is becoming increasingly important and critical in modern operations, especially in the mine-to-mill. Prompt gamma neutron activation analysis has long been utilised for real-time elemental analysis in bulk materials, with Scantech's GEOSCAN being the instrument of choice in the minerals sector. Working in the minerals space for 15 years, the GEOSCAN has been successfully implemented in a wide range of minerals applications including iron, copper, lead-zinc, manganese, phosphate and more, and it caters for the very high demands and increasing requirements of a contemporary processing facility. An area of focus has been on increasing the analysis frequency to allow for rapid analysis results with the same high degree of accuracy typically expected of the GEOSCAN. This paper discusses the underlying research and technology that has enabled such rapid analysis and presents a range of examples using a thorough statistical approach on real production material, demonstrating achievable accuracy over a short analysis time, and dispelling common myths about the speed of the technique. Potential applications are discussed to conclude the paper.INTRODUCTION Technology and the information it can provide plays a critical role in the evolving modern mineral processing landscape. The importance of technology to analyse various features of ores and concentrates being processed is obvious, and recent years has seen the advance of numerous technologies to provide a variety of real-time measurements on conveyed material flows. From sampling apparatus to particle size analysis to weight and density meters to full elemental analysis, the availability of information enables a variety of improvements in the process leading to improved efficiency and increased revenue. To maximise the potential benefits, access to real-time information is imperative, and rapid updates of information become necessary to make appropriate process control decisions based on the most relevant and up-to-date information."

Jan 1, 2017

By C. C. Furnas

In the course of an investigation3 of the flow of gases through beds of broken solids the author obtained a number of data .on the specific volume of beds of broken solids of variously mixed sizes. A mathematical theory of the limiting conditions has been developed and some generalizations have been made for intermediate cases. A more definite knowledge of the relation between space occupied and size composition would be valuable to all those who are handling large quantities of broken materials. Such knowledge might be advantageously applied to the operation of a coke oven. For example, the output of the oven depends in general upon the number of pounds of coal which can be put in the oven at charging. It is known that the capacity of one battery of ovens was increased several per cent by slightly increasing the proportion of fine material in the charge.

Jan 1, 1928

By A. W. Frolli

This paper, describing the mining and reduction methods and costs at the Oceanic quicksilver mine, is one of a series of similar reports being prepared by the Bureau of Mines on various mines in the United states. The property, which is owned and operated by the Anglo American Mining Corporation, Ltd., is 5 miles east of Cambria, San Luis Obispo County, Calif. It lies in a region of steep hills and sharply incised canyons on the west slope of the Santa Lucia Range at an elevation of about 500 feet above sea level. The climate is ideal for living and operating conditions. A 40-mile paved highway connects the mine with San Luis Obispo, the nearest convenient railroad town.

Jan 1, 1937

By M Dunglison, P M. Cameron

Simultaneous mass-balancing of a mineral processing flow sheet results in adjustments to each data point that reflects the accuracy and precision across the full set of data. In this way, all the good work that goes into designing the sampling and analysis protocol for each sample point is leveraged in order to produce a æbetterÆ set of balanced numbers for every sample point in the circuit. Few operating plants employ whole of circuit balancing techniques to produce reported operating results. This situation is changing with the application of mass balancing technology which utilises redundant data for production accounting and metal reconciliation from product to ore source across multiple phases and multiple time periods. Mine and plant data can now generate credible information to improve productivity. Mine and plant personnel can now use consistent data sets for review and planning. Decisions based on balanced data can be made quicker and with increased confidence.

Jan 1, 2005

By Kelly J. Driscoll

Impure zinc (98.5%) was electrorefined to high purity zinc (99.995%) using a fused salt electrolyte of molar composition 1: 1 : 1 :2 ZnCI2:KCl:NaCl:LiCl with a current efficiency of about 90% at 723 K. A recessed channel electrorefining cell was developed which achieved excellent mixing of both the metal and the electrolyte and by ensuring a very small anode to cathode spacing the voltage drop across the cell was 0.16 V and at a current density of 7kA m-2. The physical characteristics of the cell were observed using a low temperature model which showed the formation of droplets and rivulets which provided mixing. The application of this approach to the refining of other non-ferrous metals is discussed.

Jan 1, 1992

By E. Barsky

The composition of multi-component materials is proved to be unambiguously determined by the composition uncertainty parameter (composition entropy). At the same time, every component, depending on its content, introduces a certain value into this parameter. Quality criterion of multi-component separation is determined by the total change of this parameter for all products obtained as a result of the separation process. This parameter can unambiguously estimate both multi-product separation and complicated schemes of modern beneficiation plants. It can be used to estimate binary mixtures separation, too. During the optimization of multi-product separation, another problem arises, which is not peculiar to binary mixtures. In this case, the total efficacy depends on the order of separation boundaries, as well. In the present paper, a specific example of initial product separation into seven products by six boundaries is investigated. It is clear that with respect to a single boundary, two products only can be obtained. In this case, the separation optimum is shown to correspond to the separation of boundary-class particles equally into both products. We have also established that from the point of view of entropy, the maximal possible separation efficacy corresponds to equiprobable composition of the initial mixture, i.e., the fine product quantity in the material to be separated is equal to that of the coarse product. Three groups of experiments were carried out. In the first group, the boundaries were consecutively specified from the finest to the coarsest one. In the second group, the boundaries were set vice-versa, i.e., consecutively from the coarsest to the finest one. In the third group, no sequence was observed. At every separation stage, a boundary was specified in such a way that the separated material composition was as close as possible to equiprobable one relative to this boundary. Total efficacy was different in all the three cases. In third group of experiments, its value is the highest, which confirms the advanced supposition. The obtained results are phenomenological, ? they can be applied to any processes of solid, liquid and gaseous materials separation.

Jan 1, 2014

By Yuhsuke Mizukami

Crude high Cr containing steel such as tool steel, heat-resistant steel or stainless steel is produced by dissolution of high carbon ferro-chromium into molten crude steel. In the refining process, decarburization is performed at the first stage, and deoxidation is followed in the next stage. Therefore, the equilibrium relation between dissolved Cr and 0 in molten Fe-Cr alloy after decarburization is very important when yield of deoxidizer is considered for the ovemll control and optimization of the process. It is well known that the yield of deoxidizer does strongly depend on the kinds of refractories of furnace in the secondary refining process. In the present work, the equilibrium relation between dissolved Cr and O in molten Fe-Cr alloy has been measured in a Cr2O3, MgO or Al2O3 crucible at steelmaking temperature. O contents at given Fe-Cr components have been lower in order of Cr2O3, Al2O3 and MgO crucible. The present results have been discussed based on the activities of the constituents in pure solid Cr2O3, and FeO-Cr2O3, MgO Cr2O3 and (AI,Cr)2O3 solid solutions.

Jan 1, 2003

By Thomas A. Steven

Most mineralized areas in the central San Juan Mountains, Colorado, are associated with the youngest subsidence structures in a large volcanic cauldron complex that formed concurrently with eruption of the surrounding ash-flow field. Two local types have been recognized: (1) fissure-vein deposits along faults characterized by relatively late movement, and (2) hydrothermally altered and mineralized areas associated with postsubsidence Fisher Quartz Latite centers. The first type has provided most production in the past; the potential of the second type has yet to be adequately tested.

Jan 1, 1968

By P. C. Good

The Bureau of Mines conducted a laboratory investigation of a sinter-leach method to recover aluminum and fluorine from waste carbon potlining residues from secondary cryolite recovery operations in aluminum reduction plants. After removal of carbon by burning, the residue was sintered at 900° to 1,100° C with silica and N2CO3, then crushed and leached with dilute NaOH solution, dilute Na2C03 solution, water, or water containing residual Na2O which remained in the sinter after reaction and decomposition of Na2CO3. Over 90 percent of the contained aluminum and up to 87 percent of the contained fluorine were extracted from this waste product in the form of a mixed alkaline solution. Treatment of the alkaline solution with CO2 yielded a white precipitate containing 89 percent of the original aluminum and 61 percent of the original fluorine as a mixture of synthetic cryolite and alumina, together with a variable excess of soda.

Jan 1, 1969

By J. A. Lombardi

"EXECUTIVE SUMMARY The use of membranes for the treatment of Acid-Mine-Drainage (AMD) water has been a 35 year mining industry quest that has only recently produced commercial scale Zero-Liquid-Discharge (ZLD) plants. The process of development of the membrane treatment of AMD has been defined by the water treatment industry’s efforts to control gypsum scaling of the membranes, an artifact of the concentration of calcium and sulfate ions on the concentrate or “brine” side of the membranes. Improved anti-scalants, changes to membrane surface geometry and a lowered permeate flux rate were all part of solving the calcium sulfate (gypsum) scale formation problem. Whether used singly or as part of a multi-stage membrane treatment process, the production of “left over” membrane concentrate or brine, in any volume large or small, was a second barrier to adoption of the method by the mining industry. The two identified “final brine” treatments were a) solar evaporation ponds and b) mechanical evaporators. Brine disposal by solar means is typically site limited to flat terrains or high net evaporation locations. Mechanical evaporation-crystallization is applicable at all sites but, typically, at onerously high ownership and operating costs. Miwatek, a South African water treatment start-up, has entered the mining AMD ZLD marketplace with two new, pilot-scale tested, processes, both of which are predicated on the innovative treatment of a reasonably concentrated AMD and neither of which produces a final brine that requires disposal. In the Miwatek Brine Treatment, MBT, method the membrane brine is caustic pH adjusted and de-calcified precedent to passage through a second membrane plant. The caustic is generated on-site by a lime treatment of the second-membrane concentrate. The first- and second-stage permeates are blended for discharge. The process usually yields no “final brine” for disposal. In the Miwatek Ettringite Treatment, MET, method a low pH first-stage membrane brine is lime treated in two or three steps in the presence of aluminum in a way that metal hydroxide and calcium sulfate solids are formed and purged from the system. Sufficient aluminum is often present in the feed water to, with judicious recycling, enable operation of the lime-aluminum treatment without the purchase of outside aluminum reagent. The first-stage membrane permeate is blended with the lime-aluminum treated membrane concentrate for discharge. The indications are that the method can comfortably meet the low 250 -500 ppm SO4 discharge water quality standards that have most recently been proposed in South America. The process yields no “final brine” that requires disposal. Projected own-operate costs for the MBT and MET systems are less than the estimated costs for all identified alternative treatments."

Jan 1, 2015

By K. Kawagishi, J. Ang, A. Sato, H. Harada

"We have recently proposed a new ""EQ Coating"" bond coat system to solve the problem of secondary reaction zone (SRZ) formation caused by bond coats applied on the hot section components of modem jet engines. A viable EQ coating alloy was previously found for a representative znd generation superalloy, TMS-82+. It would be ideal if the same could be done for a representative 5th generation superalloy, TMS-173. In this paper, we will show that the coating with the best oxidation resistance in the EQ system of TMS-173, although possessing considerably better resistance than TMS-173, did not have sufficient oxidation resistance. In order to improve the oxidation resistance of the EQ coating for TMS-173, we have ventured into ""Pseudo-EQ coatings"". A diffusion couple between the Pseudo-EQ coating and TMS-173, after 300hrs at 1100°C, had a 0-15µm IDZ, but no SRZ. A diffusion couple between a conventional coating and TMS-173 formed a 80-150 µm SRZ. After a 1 hr oxidation test at 1100°C, the PseudoEQ coating formed a thinner oxide layer than the EQ coating, but still contained NiO and spinel. Aerospace"

Jan 1, 2006

By N. W. Stump

New developments in on-stream analysis using immersed radioisotope gauges including results from plant installations are described. The control of grinding and flotation using a small digital computer has been complemented by this development. A control scheme for grinding which is based on maximum throughput at constant product size and preliminary work in flotation control are also outlined.

Jan 1, 1974

By J. Gebhardt, D. McBride, C. R. Bennett, Croft. N., M. Cross

A comprehensive model of solution flow through heap leach systems requires a numerical solution with the ability to predict variably saturated-unsaturated flow through porous media domains that contain materials with spatially variable properties. The types of flow associated with stockpile leach processes lead to flow problems, such as infiltration into dry soil, drainage, perched water tables and flow through heterogeneous materials. Computational methods for modelling this class of flow behaviour are conventionally based on the classical Richards' equation. However, the governing equations are highly non-linear, difficult to solve, and require iterative numerical solution methods. The pressure-based form of the Richards' equation suffers from poor mass balance, while the mixed form can possess convergence difficulties. An adaptive transformed mixed algorithm is described, which reduces the non-linearity of the problem, optimizes the time step size, and provides a fast, numerically robust scheme that significantly reduces computation (or CPU) time. This method is shown to give fast, accurate solutions on a number of complex flow problems. The utility of this algorithm is illustrated through its implementation within the PHYSICA computational modelling software, which incidentally, provides a framework for a comprehensive heap leach model.

Jan 1, 2005

By The Staff

Introduction In this paper it is proposed to discuss briefly some of the problems confronting the management of a gold mine in choosing a method of milling to recover the gold from various classes of ore. In order to simplify the discussion, the more common types of gold ores are classified from a metallurgical point of view as follows: Class 1?A: Free-milling ores which require only relatively coarse crushing. B: Free-milling ores which require finer grinding to release the gold. Class 2?A: Gold ores which contain the gold partly in the flee state and partly associated with a small amount of iron sulphide, and which do not require fine grinding. B: Gold ores similar to 2A, but which require fine grinding. Class 3?A: Gold ores containing copper in quantities insufficient to interfere to a serious extent with cyanidation. Gold ores containing copper in sufficient quantity to interfere with cyanidation but in which a large proportion of the gold is in the free state, the remainder being chiefly associated with the copper mineral, chalcopyrite. Gold ores containing copper and other sulphides, such as pyrite, etc., in which the gold is principally associated with these sulphides.

Jan 1, 1931

By P Navarra, R Kuhne

Dynamic simulation (discrete event simulation) is the preferred methodology to evaluate the impact of dynamic aspects of processing plants on the overall plant capacity. This tool can be used to: identify bottlenecks in the plant,justify upgrade and expansion projects by evaluating their impact, oroptimise maintenance and operating practices without disrupting the operation. Iron Ore Company of Canada's (IOC) pelletising plant is a complex operation because of multiple products, varying equipment capacity and shifting bottlenecks. Furthermore, with extensive capital requirements for projects and long lead times, a high level of confidence in project outcome is required. Therefore, a model of IOC's pelletising plant in Labrador City was constructed in 2007 by a joint IOC and Hatch team. The model includes both operational and metallurgical aspects in order to better capture the complexity of IOC operation. In this paper, the justification, boundaries, and functionality of the model are described. A comparison of simulation results to historical plant operation is given. It is observed that projects have interactions and that the benefits of combined projects are not equal to the combined benefits of the individual projects. Projects can have synergies that result in greater benefits when combined or can have overlapping benefits that result in lower benefits when combined. The power of the proposed modeling exercise lies in the ability to assess the impact of projects on overall performance.

Jan 1, 2009

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"K. A. DIGREGORIO, E. v. CILENTO, AND R. c. LANTZ. Measurement of superoxide release from single pulmonary alueolar macrophages. Am. J . Physiol. 252 (Cell Physiol. 21 ): C677-C683, 1987.-An electrooptical method was developed to quantify superoxide (02) release from single rat pulmonary alveolar macrophages (PAM) during adherence to the bottom of a culture dish. This was done by measuring the reduction of nitro blue tetrazolium (NBT) to a diformazan precipitate at 550 nm from videorecorded images of individual cells. Temporal changes in cell optical density, which are proportional to the mass of diformazan produced, were calculated from videophotometric measurements of the change in light intensity over individual cells. Total diformazan produced increased 78 and 1263 with an increase in NBT from 0.5 to 1.0 and 2.0 mg/ml, respectively. Total diformazan produced and maximum rate of production among individual PAM varied two- to threefold providing strong evidence for heterogeneity in 02 production. Specific inhibition of 02 production by superoxide dismutase, iodoacetate, and chlorpromazine significantly reduced the total diformazan produced and maximum rate of diformazan production. Hydrogen peroxide was not involved in NBT reduction, since catalase alone did not significantly change diformazan production. This novel method to quantify 02 release from single PAM should be valuable in analyzing heterogeneity and single cell kinetics of O; production, in assessing the effects of exposure of cells to particulates on O; release, and in relating release to electrophysiological measurements.rat; nitro blue tetrazolium; macrophage heterogeneity; single cell kinetic PULMONARY ALVEOLAR MACROPHAGES (PAM) protect the lungs by phagocytizing foreign debris and bacteria (24). This process involves ingestion as well as destruction of foreign matter. Phagocytosis is usually accompanied by a respiratory burst that increases cellular oxygen consumption and glucose metabolism in the hexose monophosphate shunt (7), which leads to the release of highly reactive oxygen metabolites at the surface of the · plasma membrane (6, 27). These agents have been implicated in the killing of bacteria by phagocytes (22), but have also been shown to be toxic and have been linked to cancer, emphysema, arthritis, diabetes, and other diseases (17, 22, 30). Toxic effects may be a result of either an abnormally low production of metabolites, resulting in damage to lung tissue by respirable bacteria and dusts, or an abnormally high production, resulting in direct damage to lung tissue by metabolites themselves."

Jan 1, 1989