Search Documents

By C. J. Beyke

In recent years recycling of household batteries has received increasing attention, primarily for environmental reasons. This article reviews the major battery types and some of the technologies available to recycle them. It also discusses issues such as collection and sorting which are related to battery recycling in the United States. Finally, results from research being conducted by the U.S. Bureau of Mines on the reclamation of nickel-metal hydride, alkaline, and zinc-carbon batteries are presented.

Jan 1, 1995

By A. A. Cochran

Methods of preparing small heats of steel containing radioisotopes were developed, and the techniques of stripping film autoradiography were used to detect and study the carbide and sulfide phases in titanium-bearing steels. Metallography had revealed areas of titanium sulfide and ferrite or pearlite adjacent to areas of titanium carbide and ferrite, and unidentified, irregular phases at the boundaries between these two areas. Sulfur 35 was used to deter-mine the extent of the titanium sulfide inclusions, and carbon 14 was used to delineate the titanium carbide phase. Individual radioactive areas were located with a resolution of approximately 10 microns. A general background exposure that was not correlated with microscopically visible phases was observed in the carbon 14 autoradiographs. The evidence from both sulfur 35 autoradiographs and carbon 14 autoradiographs indicated that the unidentified inclusions were sulfides rather than carbides. INTRODUCTION The use of radioisotopes to facilitate the work at the Rolla Metallurgy Research Center was expanded in fiscal year 1959 when the Bureau of Mines authorized the installation of an intermediate-level radioactivity laboratory. Before this time, sealed cobalt 60 sources had been employed for radiography, but no tracer work was done. The primary objective of the first experiments conducted in the new laboratory was to supplement physical metallurgy investigations of selected problems in steel research.

Jan 1, 1962

By David M. Lapham

In Pennsylvania, 310 sampled sites of clay and shale have been evaluated for: potential use, chiefly as structural clay products, refractories, and lightweight aggregate; lithology; physical properties tests; fired tests, both quick-fire and rotary kiln; major-element chemical analyses, and quantitative five-component X-ray mineralogy for quartz, mica, feldspar, kaolinite, and chlorite-vermiculite-montmoril-lonite. Approximately 80 percent of the samples are of some potential use. Of 220 shale samples, 84 were potential lightweight aggregate sources and 83 potential brick sources. Binary correlations of test data versus potential use indicate that certain empirically determined parameters may be critical. These are: lithology, particularly for medium to super-duty refractories and lightweight aggregate; kaol-finite content for refractories versus low-temperature fired product sources; quartz content illustrating that there is an apparently necessary minimum quantity for brick; quartz content, which is low in high grades of lightweight aggregate; mica content, which is low for refractories and possibly high for lightweight aggregate; total iron, which is low for refractories and shows a 40 percent minimum for lightweight aggregate; carbon dioxide, which is low for refractorfes, beneficial in lightweight aggregate, and probably restrictive for some tiles choroite yermicalite, which is low for refractoies and possibly beneficial in lightweight aggregate. In Pennsylvania, clay and shale materials constitute one of the state's major economic mineral resources. To date, the testing program indicates considerable development potential in brick, tile, and lightweight aggregate industries, and perhaps a future potential for aluminum from shales that exceed 20 percent A12Q3.

Jan 1, 1971

By A L. Randriamanjatosoa, G Small, C Greet

In flotation simulation models, the effects of pulp chemistry other than pH are often ignored and reduced to particles hydrophobicity or contact angle, neither of which can be measured readily in real time in an operating plant. The flotation response of a given sulphide mineral is known to be influenced and can be improved by changing the chemical characteristics of the pulp during grinding and flotation. The on-line measurement of pulp pH, potential, dissolved oxygen, temperature and oxygen demand of a process stream was completed with the PCM® (Pulp Chemistry Monitor) developed by Magotteaux in this study. The data generated together with relevant plant operating parameters were used to construct an empirical model and simulate the metallurgical performance of the ore. The same approach was also applied to laboratory flotation tests data using various grinding media types. The flotation models better fit the actual data when the chemistry of the pulp is taken into account.CITATION:Randriamanjatosoa, A L, Greet, C and Small, G, 2018. Effects of pulp chemistry on plant and laboratory flotation modelling, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 423–432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Zhao, Q B. Zhang

The shock behaviour of a material represents its response to very high strain rate loading at pressures associated with those generated by explosive and blasting loadings. Three sets of shock wave experiments have been conducted to determine shock Hugoniot behaviour, spall tensile strength and shear strength using a plate impact facility. Embedded manganin stress gauges (ie longitudinal and lateral gauges) and high-speed velocimetry using heterodyne techniques were used for the measurements of stresses, shock velocity and free surface velocity. The gabbro exhibited classic linear Hugoniot equations of state in the US-up (ie shock velocity-particle velocity) plane; while for marble a polymer-like non-linear response was observed. The detailed experimental procedures used to make these measurements are to a great extent standard methods when determining mechanical properties and deformation fields at high strain rate.CITATION:Zhang, Q B and Zhao, J, 2015. The response of rock materials to one-dimensional shock loading, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 665–672 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D. Maddocks

"IntroductionThe greater part of the iron ore industry in Canada is located along the Labrador-Quebec border on a geological formation known as the Labrador trough. The Labrador trough is a 700 · mile long geosynclinal segment composed of folded and faulted Proterozoic sediments, volcanics and intrusives, extending from Gagnon, Quebec, to the north west tip of Ungava Bay. This geosyncline can be divided into three parts (Fig. 1).The northern unmined part, extending from southern to northern Ungava Bay, is a low grade metamorphosed iron formation.The iron deposits of the central region, represented by Schefferville, are hematite-limonite ores formed by oxidation and leaching of an unmetamorphosed taconite formation. Average iron content of the ore is greater than 540Jo for direct shipping and 50% for plant feed.The deposits of the southern section (Carol Lake, Wabush, Mt. Wright, Gagnon) extend from just north of Carol Lake to Gagnon and is a metamorphosed silica-iron oxide (specular hematite and magnetite) formation averaging plus 30% iron.The mineral wealth of this area was first observed by Father Louis Babel about 1870 and again by Dr. A.P. Low of the Geological Survey of Canada in 1894. However, the remote location hindered development until after 1945. First production of direct shipping ore from Schefferville was in 1954. Production at Carol Lake commenced in 1962.This area now accounts for sixty million long tons (61 Mt) per year of processed iron ore products as follows:This chapter will concentrate on pelletizing and agglomeration as experienced at the Iron Ore Company's Carol Lake operation. However, whenever possible, reference will be made to alternate methods, procedures, equipment, etc."

Jan 1, 1989

By H. L. Fraser

A review of the possibilities of performing microchemical analysis in thin sections using a combination of scanning transmission electron microscopy and energy dispersive spectroscopy of x-rays is given. Particular attention is paid to the factors that limit accurate analysis at the highest spatial resolution. As an example of the use of these techniques applied to a potential problem in minerals processing, the identification of iron pyrite and pyrrhotite particles in Illinois, Herrin #6 coal is presented.

Jan 1, 1981

By H. A. Watson

Laboratory tests on three commercial methane detectors, two combustion-type detectors and one interferometer-type detector, were made by the Bureau of Mines to determine their response to certain single and multiple flammable gases mixed with normal and abnormal air atmospheres. Although both types of detectors responded accurately to methane-normal air mixtures, they did not show correct concentrations for other single flammable gases in air. Uniquely, the response of the interferometer-type detector to hydrogen was in a negative direction. The effects of individual gases in multiple flammable gas mixtures were approximately additive. In oxygen-deficient atmospheres the methane response of the interferometer-type detector erred on the high side, but only in very low oxygen concentrations were the combustion-type detectors affected-showing low, erratic methane readings.

Jan 1, 1966

By M. Jayaraman

With the ever increasing demand for commodities, due to changes in lifestyle and increase in population, people are striving to find ways to keep up. Mining is one essential element in the solution. Though being a powerful boost to a country?s economy, mining can have disastrous effects in the absence of waste management practice and technologies; because of the harmful heavy metals and toxic chemical waste that is generated as a by-product in mining operations. It is an established and documented fact that pollution is a major concern for communities having to live with it. Disproportionate water consumption significantly impacts local rivers and ponds thereby reducing freshwater availability and have given rise to social conflict. In light of these misgivings, management and treatment of mine water and waste has gained considerable attention recently. In this paper, we summarize some of the treatment methods that can be adopted by mining companies to reduce their environmental footprint. Appropriate treatment solutions depend on various factors including available space and capital cost for treatment solutions, type of mining waste generated, current state of the mining plant, geographical location, and other location specific issues. Incorporating waste and water management solutions as a priority within mining operations is critical for addressing increasing regulatory requirements and a starting point for initiating other Corporate Social Responsibility (CSR) programs. Collaboration among mining companies, NGOs, local community, and government facilitates successful projects which build trust leading to long term relationships. In this paper we also talk about the benefits of implementing a CSR project that captures the focus of local communities and allows the mining company to focus on operations. Implementing a sustainable business model that incorporates the broader community impacted by projects will continue to benefit even after the mining company ceases operation in that location. The challenges involved with implementing effective CSR projects, which require measuring and reporting effectiveness to create a positive social, economic, and environmental impact is also presented in this paper.

Aug 1, 2013

By G. S. Hume

Dr. K. A. Clark: No one will doubt the statement of fact that, during drilling operations through the bituminous sand beds in the Mildred-Ruth Lakes area, the core-barrel was found to contain bitumen with minor amounts of sand instead of bituminous sand. But many will doubt the interpretation of this fact as meaning that beds of bitumen occur interstratified with the bituminous sand beds. They will prefer to hold faith in the laws of physics, which deny that sand will float on oil or that fluid under pressure will not flow away through a permeable medium, until it is proved that the appearance of the oil in the core-barrel was not due to circumstances surrounding the drilling of the bituminous sand beds. The implication of the interpretation that sand is floating on oil is clear and it is unacceptable. Bituminous sand is unconsolidated sand more' or less saturated with a viscous oil. It is as difficult to conceive of bituminous sand lying on top of a body of the viscous oil as it is to conceive of unconsolidated sand more or less saturated with water lying on top of a body of water. The only difference between the two concepts is that the oil is viscous whereas the water is fluid. Oil-soaked sand placed on viscous oil would, when released, sink through the oil slowly, whereas water-soaked sand would sink through the water quickly.

Jan 1, 1947

By R. J. Henry

This paper describing the mining practices at the Teck-Hughes mines at Kirkland Lake, Ontario, is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in various mining districts. HISTORY Prospecting was begun in the neighborhood of Kirkland Lake in 1906, but staking did not take place until 1911. Gold-bearing veins were discovered by surface trenching in 1913 on the mining claims which now make up the Teck-Hughes Gold Mines (Ltd.). A small mill was erected in 1916 after the completion of some underground exploration. A transmission' line was built in 1917 to the camp to provide adequate power for a vigorous underground campaign. Also in 1917 the present management took control operations since 1916 have been continuous,' with a steady increase in production to date.

Jan 1, 1930

By S Bluhm, L van den Berg

In planning mine ventilation systems, heat issues are normally associated with deep-level mines where auto-compression and virgin rock temperatures play a major role. However, a number of mines suffer from high ambient temperatures and humidity, very steep virgin rock temperature gradients and an influx of hot groundwater. Mines in Australia and, particularly, South-East Asia have to deal with these environmental conditions, both in the operational and planning phases. These operations normally have to take heat into consideration during the planning stages at much shallower depths. In high rainfall regions, the water table is saturated and groundwater flow rates are particularly high, which add significant water heat load potential to the mine ventilation system.This paper considers the ventilation challenges associated with hot groundwater conditions in mechanised mines. The paper is based on specific project experience gained from a number of projects in the United States, Australia and South-East Asia and draws on data from mines that experience hot groundwater conditions. For one site, actual decline temperature survey measurements, modelling techniques, management strategies and design considerations are presented.CITATION:Van den Berg, L and Bluhm, S, 2015. Ventilation planning considerations when dealing with hot groundwater, in Proceedings The Australian Mine Ventilation Conference, pp 211–218 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By K. A. Clark

"The repacked mineral aggregates of good grade oil sands have permeabilities ranging between 15 darcys to 350 millidarcys. The variation is due to the silt contents of the aggregates. Few good grade oil sands contain as much as 30 per cent •silt, most of them contain less than 20 per cent, and a large proportion have less than 10 per cent.The permeabilities of repacked good grade oil sands (oil included) depend on the degree of liquid saturation. When saturation with oil plus water reaches between 80-90 per cent, permeability is reduced to zero. As total saturation decreases below 80 per cent, permeability increases ranidly. Permeabilities of between one and two darcys were observed for total saturations between 60-70 per cent.The mean value for 18 measurements of the permeabilities of ""undisturbed"" core samples of good grade oil sands was 50 millidarcys. This value is •probably too high. The mean value for 20 measurements on core samples of interbedded oil sand and shale was 100 millidarcys. The mean value for 11 measurements on shale was 10 millidarcys."

Jan 1, 1960

The effect of superficial gas rate distribution (Jg profile) on down-the-bank metallurgical response was tested in the rougher-scavenger bank (eight 10-m3 tank cells, 4 roughers and 4 scavengers) at Highland Valley Copper Mine's Cu/Mo separation circuit. Three Jg profiles were tested: (a) as found (i.e., typical practice), (b) increasing decreasing (i.e., increasing from cell 1 to 4 and decreasing from cell 5 to 8), and (c) decreasing-increasing (i.e., decreasing from cell 1 to 4 and increasing from cell 5 to 8). The Jg profile approach proved to be of considerable value. Profile (b) gave the best metallurgical results, i.e., the highest down-the-bank grade/recovery (increase in grade at constant recovery was approx. 3-4% compared to the as found case) and the most efficient Cu/Mo separation (cumulative Cu recovery was reduced by almost half - approx. from 20% to 12%, at 99% Mo recovery). The success of the evaluation prompted the implementation of profile (b). Detailed gas dispersion characterization tests (Jg and Db (bubble size)) showed significant discrepancies between the Jg measured directly (using the McGill University sensor) and the Jg calculated from field instrument readings (volumetric gas flowmeter) and machine dimensions (cell cross-sectional area). Tests were designed to reveal the source of disagreement. It was observed that a significant number of bubbles were not able to float (i.e., they were entrained with the tailings), the evidence appearing to be a significant number of very small bubbles (approx. 200-300 µm) which did not have sufficient buoyancy to rise. Consequently, rather than relying on the field instrument, the evaluation depended on the McGill University Jg sensor, which collects bubbles in a tube near the pulp-froth interface, thus providing significance to the data as the measurements were obtained from bubbles that almost certainly floated.

Jan 1, 2007

"Beneficiation of low grade ores is the process of increasing the grade of a mineral through unit operations that remove and separate the waste (or gangue) material from the valuable mineral that can then be used for further processing or direct use. Important factors when deciding upon a beneficiation program are the feed grade, mass yield and the metal recovery. As lower grade ores are being processed beneficiation is a critical process. How predictive is laboratory test work for “as built” operating projects? Beneficiation includes all or some of the available unit operations to produce a beneficiation flow sheet i.e. associated unit operations including but not limited to optical sorting, radiometric sorting, crushing and screening, coarse cobbing, jigging, dense media separation (DMS), spirals, magnetic separation, flotation, thickening, filtering and drying. Reference to specific projects and the approach developed in formulating a beneficiation flow sheet and a comparison of difficult and simple beneficiation flow sheets are cited. INTRODUCTIONReserves of high-grade iron ores are reducing all over the world, at an alarming rate, over the years as a result of the rapid increase in demand for steel particularly from Japan and then China. The recovery of mineral value from the low-grade ores using present technology is more expensive than DSO ores due to high energy and capital costs. Beneficiation is defined as a variety of processes whereby extracted ore from mining is reduced to particles that can be separated into mineral and waste.Various physical properties of an ore can be exploited to separate a low grade fraction including variation in hardness, density, reflectance, conductivity and magnetism.""Beneficiation"" of iron ores includes concentration, generally by physical removal of unwanted gangue. Also considered beneficiation is the regulation of product size, or other steps such as agglomeration to improve its chemical or physical characteristics prior to smelting."

Jan 1, 2012

By William James Kempson

This paper discusses ore handling systems in shafts. These are considered from the loading facility at shaft bottom all the way through to the discharge mechanism in the headframe. These systems will be discussed from the following perspective: i. Intrinsic safety of the systems ii. The efficacy of the systems to perform consistently iii. The maintainability of the systems iv. Overall system cycle times Particular emphasis is placed on the following specific areas: 1. The Shaft Bottom Loading Facilities The various shaft loading systems currently in use are discussed, the selection parameters surrounding these are quantified and the specific selection criteria are outlined. 2. The Various Skip Configurations In this section the various skip configurations in use around the world will be described and the specific design details associated with these will be highlighted. The advantages and disadvantages of these systems will be compared and the overall efficacy of these will be discussed. 3. The effect of the loading and skip configurations on the Load Cycle Times. The overall cycle time which can be achieved by a shaft system is strongly dependant by the speed and efficiency with which the ore can be loaded and transported out of the mine. The potential of the various systems to be optimized will be discussed. The emphasis of this paper is to highlight the lessons which have been learned with respect to ore transport system design and provide a common basis against which these can be compared in future applications.

May 1, 2013

By J Välivaara

The mining industry will face numerous challenges over the next 10–15 years as new deposits are likely to be more remote and lower grade and existing deposits will be mined deeper. As a result, mines and mining contractors operating in deep-mine conditions will need to focus on the quality of drilling and blasting to minimise unnecessary waste rock excavation to keep costs at an acceptable level. In addition, increased demand for improved safety and operator ergonomics will set greater demands on original equipment manufacturers of mining equipment. Finally, difficulties finding a skilled and experienced workforce, particularly in remote mine locations, have already negatively impacted mines’ ability to achieve high productivity and low operating costs.This paper introduces techniques and shares practical experiences in increasing productivity and reducing the costs of excavation in underground face drilling. The paper uses Sandvik’s new DD422i automated mining jumbo as an example of the type of equipment needed to deliver the features and corresponding benefits for future mine development. Case studies using this equipment are presented to illustrate the points made in this paper.CITATION:Välivaara, J, 2016. Automated drilling features for improving productivity and reducing costs in underground development, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 723–730 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D. Steele, B. Ndlovu

"Adequate characterisation of clays is becoming increasingly important as operating mines move into areas of more complex ores. The processing therefore needs better mineralogical characterisation to identify problematic ores for better planning before issues arise. While a number of instrumental mineral characterisation methods are available, X-ray Diffraction (XRD) is widely recognised as perhaps the best technique for the identification and quantification of minerals, particularly clays. When an appropriate sequential and systematic sample preparation and treatment protocol is employed with instrumental XRD analysis individual clays can be uniquely identified, and the proportions of interstratified clays can also be quantified. The effect of sample preparation on the XRD analysis and identification of clays was investigated in this study. The results showed that sample preparation protocol is indeed critical to accurately analysis and characterisation of clays. For example, both dry grinding and micronizing affected the degree of crystallinity of kaolinite leading to the formation of reactive surfaces or changes in the physicochemical behavior. It was also found that the apparent degree of preferred orientation in platy minerals correlates directly with the amount of force/pressure applied during the preparation of backfilled powder samples. This work showed that manual preparation can produce highly variable peak intensities especially with minerals that show any preferred orientation. KEYWORDS Clay; XRD; kaolinite INTRODUCTION Clays are important in our life and they have numerous applications in modern world from cosmetics to environmental remediation. Therefore, clays have been extensively investigated for many years. Adequate characterisation of clays is becoming increasingly important as the mineral processing industry faces more complex mineralogy with the need for better mineralogical characterisation to identify problematic ores and plan accordingly. In most studies, X-ray diffraction (XRD) method has shown the unique capability to characterise mineralogy, especially for the fine grained size materials. The XRD technique is particularly diagnostic for clays. It is known that under ideal conditions, the peak intensities of an XRD diffractogram are proportional to the concentrations of individual minerals present in the sample. Hence, the qualitative mineralogical data obtained from XRD can be quantified, using either the internal or external standard methods. However, it is also known that clays are particularly sensitive to the influences of sample preparation method due to their physical characteristics (e.g. fine grain size, morphology, relative physical softness, crystallinity, thermal sensitivity) that could be destroyed by inappropriate preparation prior to the analysis. Thermal and mechanical treatment and grinding of clays can change their crystalline structure, and consequently, their characterisation results by XRD analysis. The behaviour of clays in grinding has been widely studied, especially for kaolinite (Miller and Oulton, 1970, Milocevic et al., 1992, Tomasevic-Canovic et al., 1992). With prolonged grinding time, the crystallinity of the clays can decrease (Filipovic-Petrovic et al., 2002). It has been shown that grinding may gradually cause the loss of hydroxyl ions of kaolinite (Gonzalez Garcia et al., 1991)."

Jan 1, 2018

By Stephen Gale, David Clarry, Edmund Smith, Jon Feldman

"In 2006, a Canadian steel maker embarked on an ambitious initiative to become “Best in Class in Energy Management”. This initiative provides the framework for this paper, with some augmentation from other energy management projects carried out by Hatch. The initiative focused on identifying energy/GHG management improvements leading to low-cost implementation of energy savings or GHG emission reduction. The key components of the approach were:• Review site energy management practices and benchmark internationally.• Review best technical practices and benchmark against public energy intensity data.• Conducted a site-wide Energy Assessment and physical review of operating areas.• Facilitation of on site-workshops with staff to prioritize savings opportunities, as well as identify and remove implementation barriers.• Development of an Energy Management Action Plan for implementation of improvements.Most organizations can produce, with relative ease, a list of ideas for saving energy, implementing them is the challenge. This paper addresses these issues as well as the profitability of the energy efficiency improvements and the consequences for GHG emissions.IntroductionWhen one of the authors was an undergraduate engineering student at the University of Cape Town in South Africa, the technical drawing instructor made a statement that was both humorous, and mildly profound. He claimed that the most successful engineer is one who is both lazy and diligent. Lazy, in the sense that the engineer is constantly on the lookout for an easier, more efficient, way to do something. Diligent, in the sense that the engineer will work tirelessly to come up with a good technical solution for the easier way. This paper, somewhat of an anomaly in a compilation of technical proceedings, hopes to break the mould a little, and to show a “lazy-diligent” way of reducing the carbon emissions from an industrial facility, using a steel plant as an example."

Jan 1, 2008

By Danqing Xu, A. W. Khair

"This paper presents a laboratory simulation of regrinding and resulting dust generation. An Automated Rotary Coal Cutting Simulator (ARCCS) was modified to conduct regrinding experiment. In order to estimate the effects of coal properties and operating parameters on regrinding and dust generation, an orthogonal fractional factorial experimental design was implemented in regrinding experiment. Marple personal cascade impactors, Series 290, were used to measure dust concentration during experiment. Three types of coal seams, namely, Waynesburg, Pittsburgh, and Lower Kittanning, were used to represent different coal properties. Experimental results and complete parametric analysis were presented.In a rotary cutting system, all the broken coal and part of the remaining coal from previous cutting cycles must be transported through part or entire circumference of the cutting drum. This transportation of already recovered coal through the cutting zone of rotary head makes it a rotary grinder. Some of the coal particles will be subjected to secondary fragmentation or regrinding in the process. The potential effect on dust generation by regrinding is significant because the cutting head utilizes kinetic energy to comminute recov¬ered coal material. The moving bits and bit blocks on the cutting head impact coal particles and transfer some of their kinetic energy to the particles. After obtaining kinetic energy, coal particles are free to impact one another and they also impact the coal seam or cutting head. During impact, high impact force and high internal stress concentration are created in the particles. Kinetic energy is transformed into strain energy. When stored strain energy exceeds allowable strain energy, the particles will break. A great amount of respirable dust will be generated due to impact failure. In reality, regrinding occurs at the same time as primary cutting. The particles to be ground are the result of primary cutting. Both primary cutting and regrinding produce dust. Therefore, it is impossible to separate regrinding from primary cutting. In order to study respirable dust generation by regrinding and analyze the influencing parameters, a laboratory approach was adopted. In this approach, it is possible to study the regrinding separating from primary cutting."

Mar 1, 1992