Search Documents

By D. H. Schwarz

The performance of proton exchange membrane (PEM) fuel cells depends on catalyst layer composition and structure. Experimental observations reveal that state-of-the-art catalyst layers consist of microporous agglomerates of carbon-supported catalyst sites bound together by polymer electrolyte. In between the agglomerates are macropores which provide pathways for the transport of gaseous reactants. In this work, three-dimensional, multicomponent and multiphase transport computations are performed using a computational fluid dynamics (CFD) code (FLUENTTM) with a new PEM fuel cell module, which has been further improved by taking into account the detailed composition and structure of the catalyst layers using a multiple thin-film agglomerate model. In this model, it is assumed that thin films of polymer electrolyte and liquid water surround the catalyst sites. The results of CFD computations show that transport limitations associated with the thin film of polymer electrolyte and the presence of liquid water in the catalyst and gas diffusion layers have substantial negative effects on PEM fuel cell performance. Also, the results of computations with variable distributions for a given precious metal loading show that, in general, uniform catalyst loading provides the best fuel cell performance.

Jan 1, 2005

By G. Reuben Yourt

This paper consists of two main parts. The first, under the heading Preparations, deals with suggested preparations to be carried out in advance so that loss of life might be prevented should a fire occur. The second part, under the heading Fire Procedure, deals with actual organized procedure to be followed for the preservation of life if and when a fire occurs. The writer realizes that these preparations and procedures may be to some extent applicable to only a few mines with a relatively simple vein system and that each mine would need to formulate a procedure to conform to its own particular conditions, scope, and degree of complexity. Preparations 1. - Ventilation Control The objective in ventilation control in the event of a tire underground is to keep the travelways, through which men must pass to reach surface, supplied with air not deficient in oxygen and free from gases and smoke. Without some control of the volume and direction of the main air currents flowing through the mine, the success of removing men to surface might be seriously hampered. ? This control is achieved by means of mechanical ventilation forcing air through desired airways and workings with the assistance of doors to regulate the volume and direction of the air flow. In connection with fans and doors, the possibility of short-circuiting should always be taken into consideration, as it can often nullify the value of a fan and possibly trap men in dangerous atmosphere if the short-circuiting involves the fire area. Main fans are often installed so that they can be reversed in a short time. However, fans should not be reversed unless this is found absolutely essential by those in authority. Misjudgment in this respect could cause the loss of life to men who might naturally take refuge in what they believe by experience to be a fresh air stream. Another precaution to be taken is to see that doors in airways are fastened in a fixed position so that they cannot be sucked or blown open when the fan is reversed, otherwise short-circuiting could possibly render the fan useless.

Jan 1, 1947

By W. G. Pariseau

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal strength and moduli and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Numerical models provide a means of quantitatively accounting for the various complications of mining geometry, the stratigraphic column, mechanical properties, gas flow properties and associated interactions. A fully coupled hydromechanical finiteelement code, utAH4, serves the purpose well and allows study of the important interaction between stress concentration and gas pressure in determining safety and stability of the face during the advance of a longwall panel in a deep underground coal mine in central Utah. Face advance is relatively fast compared with gas flow and depressurization in coal seams of low gas permeability. Consequently, gas pressure is high at the face. When a longwall is stationary, depressurization occurs at the face, so effective stress and strength increase. thus, when gas flow at the face is high and requires a pause in face advance to bring gas concentration to an acceptable level, a second benefit occurs because of timely depressurization. However, quantitative analysis of a deep coal mine shows that regardless of gas pressure, high stress concentration is more likely to pose a threat to face and pillar wall stability.

Aug 1, 2013

By Frame Ritzert, Dennis Keller, Vijay Vasudevan, David Arenas

"An investigation was conducted to describe topologically close packed (TCP) phase instability as' a function of composition in the advanced ·Ni-base superalloy Rene N6. TCP phases are detrimental to overfill high-temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements. Thirty-four variations of polycrystalline .Rene N6 determined from a design-of-experiments approach were cast and homogenized at 13 l5°C for 80 hours followed by exposure at 1093°C for 400 hours to promote TCP formation. The alloys had the following composition ranges in atomic percent: cobalt 10.61 to 16.73, Mo 0.32 to 1.34%, W 1.85 to 2.52%, Re 1.80 to 2.11%, Ta 2.36 to 3.02%, Al 11.90 to 14.75%, and Cr 3.57 to 6.23%. Physical and chemical characteristics of all microstructures obtained were described using various analytical techniques. From these observations, a mathematical description of TCP occurrence (s and P phase) was generated for polycrystalline Rene N6.IntroductionNi-base superalloy single crystals represent the state-of-the-art for turbine engine airfoil application as they offer the best balance of properties to allow for the high operating temperatures required: for efficient engine operation.1 Current trends in alloy design take advantage of improved creep rupture strength with the addition .of higher levels of refractory elements. 2 In .particular, the addition of significantly higher levels of Re in third generation superalloys is key for both microstructural stability and creep rupture strength. 3 While the presence of the refractories is thought to provide strength benefits from solid solution hardening, a tendency for alloy instability in the form of topologically-close-packed (TCP) phases or secondary reaction· zone (SRZ) ·phenomena accompanies the high refractory content. 3 The formation of these phases in sufficient amount is detrimental to the overall high temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements.4 The tendency for a particular composition to form TCP may not be immediately known since the precipitation of TCP phases in Ni-base superalloys is nucleation controlled, thereby requiring long times at elevated temperatures to precipitate. 5 They preferentially nucleate along the octahedral planes of the Ni-base superalloys, usually in areas of refractory metal enrichment at grain boundaries or inside dendrites.5-6 In Rene N6, two closely related TCP phases, a and P, have been observed.2"

Jan 1, 1998

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes are considered one of the most promising alternatives to well- established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic- containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (DoD). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By G. T. Krempasky

This report covers the installation and evaluation of lb reinforced concrete sets, 6 in each of 3 mines in the Goeur d'Alene mining district, Shoshone County, Idaho, and is the second of a series to determine the feasibility of a more permanent type of mine support. Closure measurements, where applicable, were made periodically of the concrete-set installations and were compared to the initial cross section of the sets. A different method of blocking was used at each test site; at one test site the type of blocking was changed several times during the test. Results from each test site are reported separately. No attempt was made to compare the cost of the concrete installations with the cost of other types of support used in the district. Such an evaluation of permanent types of support would require a longer period of time. At this time, tests are not complete enough to determine the applicability of underground concrete supports. However, results to date tend to confirm the general opinion that precast concrete mine supports could be used to advantage in openings that require support and must have long life, especially where decay of timber is an important factor.

Jan 1, 1963

By G. Shore

"The development of a DC resistivity instrumentation system for data acquisition in extreme topography yielded an unexpected bonus in the quality and information content of the type of raw data gathered. Not only were traditionally too-rough areas being investigated systematically for the first time, the unique high-density, multi-directional raw data were providing the opportunity to greatly expand the range of conductive and resistive signatures that could be accurately recognized. Using a true 3-D inversion algorithm, 3-D earth resistivity imagery began to show distinctive anomaly patterns for hydrothermal mineralization at the seldom-visited resistive end of the spectrum, successfully imaging epithermal gold systems in conditions that had defied conventional ground and airborne geophysics for years.The traditional mode of designing a resistivity survey to test a specific target concept was shown to be an unnecessary limitation on exploration thinking when a single sweep acquisition of dense, multi-directional 3-D raw data could effectively provide the all-targets “shotgun” coverage that would take 10 or 12 conventional surveys to duplicate. Exploration planning has the opportunity to move from single steps of trial and error geophysical testing to a mode of mapping everything at the outset, and then sorting out what might be of exploration interest in the results. Survey parameterization becomes the non-technical process of marking an outline on a map and declaring “survey here.” Operational and interpretational reasons for not testing where the exploration interest lies have all but disappeared. With any-terrain capabilities and unprecedented raw data density and overlap to support interpretation of complex conditions, that outline can be drawn through extreme rough terrain, including lakes, cliffs, industrial facilities, and grounded installations to test for generally unknown sub-surface features of potential interest.As more is learned about the larger-scale signatures of ore settings and the district-scale geo-electric imprint of hydrothermal processes on lithology, it appears that the only thing certain about ore signatures is their uncertainty. This is not bad news. New opportunities abound as the advanced 3-D technology allows a first effective look at the previously unexplorable rough terrain or complicated settings, and a second look at areas where older results may now be known to be non-definitive."

Jan 1, 2002

By Satya Harpalani

The four most important parameters controlling the flow of gas in coal are the gas content, permeability, diffusion coefficient and cleat characteristics. Estimates of these and, more importantly, a knowledge about the variation in their values over time are required for simulation of long-term gas production. This paper describes experimental techniques to determine each of these, along with their time dependency, under simulated in situ conditions. It is shown that the permeability, diffusion coefficient and the cleat aperture values are not constant as usually assumed to be. There is a significant variation in their values as a result of changes in the microstructure of coal associated with release and flow of gas.

Jan 1, 1995

By Amauri Garcia, Rodrigo Valenzuela Reyes, Noé Cheung, José Eduardo Spinelli, Leonardo Fernandes Gomes, Rafael Kakitani

"The present research work deals with directional solidification (DS) of both Al-15wt.%Si and Al-15wt.%Si-1.5wt.%Mg alloys and further characterization of the related microstructures. The growth of refined primary Si and refined eutectic is well-known as positive in order to improve mechanical properties of the Al-Si based alloys. Alloying is also an effective method to strengthen the Al-Si based alloys, in which Mg is considered an important alloying element. However, lack of investigation regarding the effects of Mg on microstructure of these alloys is noted. So, in the present research work emphasis is given on both dendritic and eutectic growth being affected by solidification kinetics (V-growth rate and G-thermal gradient) during transient directional solidification. Experimental evolutions of microstructural spacing of both alloys have been determined which becomes possible to understand the effects of Mg coupled with the effects of growth rate on the final microstructural arrangements. A direct comparison of the tensile mechanical properties obtained for the alloys is also performed. It is shown by these correlations that the addition of Mg generally improves the tensile mechanical resistance with a minor decrease in ductility. Furthermore, the Scheil solidification path of the ternary Al-Si-Mg alloy was determined using the computational thermodynamics software Thermo-Calc, resulting in the following sequence of precipitation: Liquid-Si-a (Al)+Si- a(Al)+Si+Mg2Si. This sequence is compared with the experimental microstructure findings.INTRODUCTION Al-Si alloys containing from 4wt.% to 22wt.% Si comprise more than 90% of all Al-based castings. Parts manufactured with these alloys have a wide range of industrial applications due to their excellent castability, crack resistance, good corrosion resistance, good weldability, low density and high strength (Bray, 1976; Zolotorevsky, 2007; Reyes, 2017). Hypereutectic Al-Si alloys are widely used and researched in the automotive and aerospace sectors due to the low coefficient of thermal expansion, resistance at high temperatures, good wear resistance and high strength (Reyes, 2017; Tebib, 2013). Above the equilibrium eutectic composition (~12.5wt.%Si) the amount of primary Si particles becomes significant (Lasa, 2003). In the place of conventional hypoeutectic Al–Si, there is growing interest in hypereutectic Al–Si alloys as a candidate material for the high-quality engines because a higher volume fraction of silicon may bring about superior properties (Matsuura, 2003)"

Jan 1, 2017

By P Bartlett, K Naidoo

Premier Diamond Mine is planning a new, mechanised, block cave, with a production level approximately 1000 m below surface. A high degree of tunnel damage is expected, due to stress and the relatively low in situ strength of kimberlite. An evaluation of the timing of tunnel excavation, tunnel size and spacing has been carried out to define critical parameters for planning layouts and development schedules. Extensive use has been made of three-dimensional FLAC3D numerical models, calibrated against known rock mass behaviour at 650 m depth, to examine the influence of undercut advance on production level excavations. These were able to represent the effect of stress rotation on tunnels during undercut advance and the effect of an inclined undercut. The analysis has provided guidelines that are possibly applicable to any deep block cave layout. The choice of drawpoint layout is of considerably less significance than the proportion of ground extracted on the production level elevation prior to advancing the undercut. The analysis shows that damage to production development will be potentially severe if it is all excavated prior to advancing the undercut, or is mined directly beneath the undercut face. The development of the main production tunnels alone ahead of the undercut may be feasible, but no breakaways should be put in as they appear to trigger a rapid increase in the severity of damage. The optimal sequence is when all production tunnels are developed at least 10 m in plan behind the undercut, where the induced peak field stress is less than 20 MPa and a maximum support pressure of 100 to 500 kN/m2 is require to contain movement. The assessment showed that the conditions are not significantly improved by increasing drawpoint spacing from 15 m to 18 m. The vertical spacing between the undercut and production level beneath is investigated. Provided production level development is carried out beneath the undercut, there would appear to be little benefit in increasing the vertical spacing between the undercut and production level beyond the current 15 m to 18 m.

Jan 1, 2000

By Yael Miron

Two recent unplanned detonations occurred during blasting operations in sulfide-bearing ores in a Nevada gold mine. Other premature detonations have also reportedly occurred at other Nevada, California, and Arizona operations within the past few years, with increasing frequency. Unplanned or premature detonations can be extremely hazardous to life and can cause extensive property damage. A miner was injured in one of these occurrences. This report, by the U.S. Bureau of Mines, is intended to acquaint personnel involved in such mining activities with the basic causes for these accidents. These causes include the exothermic oxidation of pyrite (FeS2) and formation of ferrous sulfate (FeS04), the exothermic and energetic reaction of the ferrous sulfate with ammonium nitrate-fuel oil (ANFO)-based explosives, and the associated elevated temperatures that can set off detonators and explosives in the boreholes. Recommendations for safe operation by the Mine Safety and Health Administration, the Bureau, and the mine involved with the recent incidents include monitoring temperatures in the blast holes, analyzing for sulfate and ferrous ions, and limiting the time between loading and firing in accordance with conditions in the blast holes. Other procedures for safe operations should fit specific conditions in, the mines.

Jan 1, 1992

By Betty L. Gibbs

Microcomputers are becoming more convenient to use at all levels of the business world, including the mining industry and mine offices. The state of the mining industry requires that we become more productive and innovative in our analysis of deposits and operations. With the help of computers, examination of options to increase productivity can be performed quickly and inexpensively. Effective use of the computer for designing underground workings combines the calculation power and speed of a computer with the technical expertise and judgment of the engineer. Computer programs can perform calculations in minutes that could take an engineer several months. The engineer must be on guard when using the computer for any calculation because it is very easy to assume the results produced by a computer program are always correct. The computer is a sophisticated calculator but cannot recognize logical errors nor transposition of numbers. Also some intuitive or obvious decisions made by an engineer are difficult or impossible to program effectively.

Jan 1, 1987

By G. R. Palmer

The success of future electric vehicles will depend greatly upon the power supply choices made today. Research is presently being conducted by automotive engineers and electrochemists to determine what battery type may be the most promising. Not only are product production and application efficiencies being evaluated but also environmental concerns of reclamation and recycling. Rechargeable batteries using nickel-metal hydride electrodes are strong candidates for these electric vehicle applications. The U.S. Bureau of Mines is investigating hydrometallurgical technology that separates and recovers purified metallic components present in nickel-metal hydride battery scrap. Sulfuric, hydrochloric, and nitric acids are all capable of dissolving the battery electrode alloys given the proper operating conditions. Solvent extraction of the leach solutions using D2EHPA removes iron, and selective precipitation shows promise of recovering the other metals in the H2SO4 and HNO, systems.

Jan 1, 1994

By E. Scheepers

Within a phosphorus producing submerged arc furnace it was found that the continuous fluctuation of the furnace between a flowrate-driven state (high throughput) and a thermodynamic-driven state (low throughput) caused both techniques to have similar overall, predictive abilities and resulted in a linear, ARX-type, adaptive prediction model as the model of choice. Secondly, this pre-diction model was developed, tested and then shown to have a reasonable, 8-hour-ahead predictive accuracy (R2, coefficient of determination) of 30% (±6%) on future Pslag values. This inherent relationship exists because, at the precise moment of a Pslag prediction, the furnace already contains the metallurgical memory (input variables to the linear model) needed to ensure that some predictive possibilities will always exists - all as a result of the long residence times in the furnace. Residence time, however, is not a directly adjustable variable but rather a fully dependent variable and a function of an array of interconnected and interactive variables. In fact, this applies to virtually all input variables, reemphasising the importance of innate metallurgical memory. Thirdly, predictive control possibilities were explored by simulating the set-points of two fully independent variables used by operators to control the process: the ratio of fixed carbon-to-P2O5 and the ratio of silica gravel-to-pellets. This linear, predictive control model showed only a slight improvement with an 8-hour-ahead predictive accuracy of 35% (±7%). This highlights how ineffective current adjustments are in optimally steering the process and how difficult even incremental improvements in feed-forward and predictive control can be. Finally, it is shown that fundamental design-, sampling- and process restrictions currently associated with the process will always limit the predictive and especially control accuracy or meaningfulness of any dynamic model. These restrictions include the size of the furnace resulting in long residence times, 8-hours sampling intervals, an extremely complex and interactive process and a 16% spatial analyses variation on the Pslag values ? the very value that the model is to predict. The point is made that, given the current status quo, even the perfect dynamic prediction model can not improve on an 8-hour-ahead prediction of 30% (±6%). This barrier can only be pierced with e.g. tidier and more frequent sampling regimes and other upfront capital investments, a decision that becomes a cost accounting exercise and that can only be taken by the management structure. An investment demanding ever-increasing attention is CFD software and it?s potential to shed more light on the complex interactions within the furnace.

Jan 1, 2014

By Edward S. Bell, Frank Angebrandt

"Nuclear reactors must have very large heat outputs to compete with conventional sources and the only feasible applications are in the production of electric power or large quantities of process steam. This paper considers alternative fuels for electric power generation in Canada. In a publicly owned utility, nuclear stations are economic for base-load generation for unit sizes of 500 mega• watts or larger where competitive fossil fuel costs are higher than about 30 cents per million Btu. In British Columbia, Alberta and Saskatchewan, fossil fuels will continue to be in adequate supply at costs lower than 30 cents per million Btu and thus, except for the special case of Vancouver Island, power generation in Western Canada will continue to be the hydraulic and conventional thermal type. In Eastern Canada, fossil fuel prices are likely to be higher than 30 cents per million Btu and most utilities will be able to install units of 500 mw or larger, so that nuclear power plants will provide much of the base-load generation required. Base-load generation comprises about two-thirds of the energy generated by power utilities. By 1990, the total annual electrical energy load will be over 600 billion kwh, with two-thirds of this load in Eastern Canada. Allowing for additional hydraulic resources which may be developed in Quebec, British Columbia and Manitoba, hydraulic generation is forecast to provide a little more than a third of this electrical energy, nuclear generation a third and fossil-fuelled generation about a quarter."

Jan 1, 1969

By Hans von Michaelis

There has been a renaissance in gold and silver extraction and recovery that has taken place over the last fifteen years, since the price of gold was freed from the $3510~ level. Despite major advances in such areas as carbon adsorption processes for gold recovery, refractory gold ore treatment, crushing and grinding, process control, etc., there still remain several gold and silver mineral processing frontiers. Frontiers related to environmental management present significant challenges especially in the USA. More than ever it is appropriate to optimize total economics by adopting a "systems approach" that integrates mining, mineral processing and environmental management.

Jan 1, 1993

By R Strand, B Usher

Environmental compliance and mine designs are increasingly including assessment of flows and water qualities as a key driver to decision-making over life-of-mine. Integrated site-wide water quality models linked to dynamic water balances have been used for regulatory submissions, feasibility studies, operating mines and mine closure studies. These models, developed in GoldSim, link aqueous chemistry to the physical system of the site-wide water balance. Geochemical mechanisms included are determined from geochemical characterisation and site water monitoring, depending on the data availability at each site. External geochemical modelling using PHREEQC, version 2 (by D?L?Parkhurst and C?A?J?Appelo) and Geochemists Workbench (GWB), (by C?M?Bethke and The Board of Trustees of the University of Illinois) identifies the most important geochemical processes to be included in the model as a series of geochemical mechanisms which include source term loading rates, pH-buffering and equilibration of water quality. Water balance components include seasonal flow variability; waste facility water storage and system lags; run-off variability; milling processes and tailings production as a function of ore types; simulation of automated and scheduled maintenance of settling ponds; water re-routing for water treatment and freshwater demand, usage and storage.Case studies illustrating the use of these models for regulatory submissions and mine feasibility studies in a variety of climatic and regulatory environments show the utility and applicability of these models. Site-specific examples of these models developed by Klohn Crippen Berger Ltd are currently used at operating mines across the world. One of the larger mines where this is used is a mature poly-metallic mine in South America where the model has aided mine managers in understanding how various planned initiatives and potential water options will result in changes to flows and water quality. It is used regularly to inform water and waste management to minimise impacts to the receiving environment as a consideration of both flows and concentrations. The mine has also used the model in support of water treatment design, regulatory submissions and mine closure planning.Further examples of feasibility and operational/compliance assessment in arid and strongly seasonal environments for planning, regulatory and closure consideration of mine wastes and pits have shown the utility and usefulness of these approaches for a range of mining operations at various stages of mine life.CITATION:Strand, R and Usher, B, ?2014. Integrated site water balances and water quality models for decision-making over life-of-mine, in Proceedings Life-of-Mine 2014 , pp 271–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Håkan Schunnesson, Kirsten Holme

"When mining high grade, narrow ore bodies, the mining method often implies a very detailed knowledge of the ore contacts to avoid unacceptable ore loss and waste rock dilution. During the past decade, the use of microprocessor based drill monitoring equipment has become an accepted technique, even for percussive drilling. On the basis of the recorded drill performance, such as penetration rate, torque pressure, thrust etc., a fast evaluation of the lithological sequence of the ore zone can be made. In order to evaluate the potential of percussive drill monitoring to pro-vide detailed information of the geometry of the ore body, the technique was tested in the Viscaria copper mine in Sweden during 1996.To provide understandable information to the mine geologist, great emphasis was placed on the separation between the drilling response generated by variations in rock conditions from variations caused by the operator and the drill system. Due to the complicated geology in Viscaria, the drilling response presented to the geologists was separated in two independent signals, one representing the hardness of the rock and one representing the in homogeneity(fracturing) of the rock. With those signals a good separation between different rock types in the ore horizon was achieved.The experience from the Viscaria copper mine is that drill monitoring not only can be used to locate contacts between rock types, but also to characterize rock conditions and, often, also to specify the exact rock type present. Because it is possible to get the drill monitoring information very quickly it is a valuable complement to diamond drilling for increasing the specific knowledge of the geology and the ore body."

Jan 1, 1997

By P W. Cleary, G K. Robinson, M D. Sinnott

Discrete element modelling (DEM) is a research tool that involves numerically solving the equations of motion of large numbers of particles. It can be very useful for investigating mechanisms that can lead to bias when extracting samples from material as it is carried on a conveyor belt or as it falls from the end of a conveyor belt. DEM is more realistic than conceptual models and mathematical models; but it is not as realistic as physical experimentation. Its primary advantages over physical experimentation are that it is cheaper and that it allows many factors to be varied while keeping other factors unchanged.This paper reviews our investigations of the performance of sampling systems by using DEM. The sampling systems investigated include falling-stream cutters, cross-belt cutters, Vezins and a device called a ætrue-beltÆ cutter, which is being developed. The purpose of the review is to explain what DEM has contributed to the theory and practice of sampling, and to indicate what it is likely to be able to contribute in the future.CITATION:Robinson, G K, Cleary, P W and Sinnott, M D, 2012. How discrete element modelling is influencing the theory and practice of sampling, in Proceedings Sampling 2012 , pp 15-20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By R. R. Lowery

The Bureau of Mines developed hypereutectic aluminum-silicon alloys which 11.7.d better mechanical properties than the unmodified hypereutectic alloy. A commercial aluminum-20 weight-percent silicon LIr alloy was selected as a ary base for improvement. The primary silicon. grains were reduced from ASTM 4-5 to ASTM 8.5 by the use of phosphorus and phosphorus compounds. The remaining eutectic matrix was refined by sodium metal additions of 0.2 weight-percent. Solid solution strengthening of the alpha aluminum was obtained by adding 2 percent copper and 0.5 percent magnesium. Also, 1 percent nickel was added to harden the alloy. Optimum thermal treatment consisted of a solution treatment for 10 hour:, at 480° C with hot water quench, followed by aging for 6 hours at 175° C. The final alloy exhibited a Rockwell B hardness of 75 ±2 in the heat-treated condition. The ultimate tensile strength was 39,5O0 psi with no recordable elongation. The coefficient of linear thermal expansion was 20.4 x 10-6 per °C in the temperature range 20° to 300° C. No wear resistance data were collected.

Jan 1, 1966