Search Documents

By Joel N. Van Sant

THIS REPORT describes the occurrence, mining, and use of refractory clay in Colorado within Region III of the Federal Bureau of Mines, which includes the States of North arid South Dakota, Nebraska, Wyoming, Colorado, Utah, New Mexico, and Arizona. Field work by the Bureau of Mines, United States Department of the Interior, included examination of active and abandoned refractory-clay mines as well as a reconnaissance survey and sampling of numerous clay-bearing formations exposed in Colorado. Information from the survey and the sampling will help guide private industry in its search for virgin sources of refractory clay. Library research of published and unpublished reports from various Federal, State, and private sources was conducted during the early phase of the investigation. Most of the refractory clay mined in the Denver-Golden district of Colorado is not used for refractory purposes but is blended with other clays in the manufacture of structural clay products. The predominantly flint-clay de-posits in the Pueblo and Fremont County districts are mined and utilized chiefly in fabricating refractory products.

Jan 1, 1959

By E. L. Rawlins

The development of commercial natural-gas reserves in the Michigan stray sandstone horizon of central Michigan during the past few years has resulted in expansion of the natural-gas industry in that State. The location of the natural-gas reserves of Michigan in the general vicinity of domestic and industrial markets is of economic importance, and in supplying these markets with natural gas a reasonable knowledge of, the extent and availability of the reserves is needed in formulating regulations for drilling gas wells and producing natural gas in analyzing the feasibility of projects to construct natural-gas transmission lines, in promoting and developing markets for the domestic and industrial consumption of natural gas, and in solving many engineering and economic problems common to the natural-gas industry. The development of the natural-gas industry in Michigan has been related closely to the development of oil production. The potential oil production of Michigan is comparable with that in most of the eastern oil-producing States. The development of oil production probably will continue, especially in the central Michigan Basin area; and as wells are drilled to deep horizons in the search for oil, more knowledge will be obtained of the gas reserves in formations above the oil-bearing horizons.

Jan 1, 1936

By Michael Rieber

Mineral economics interfaces the mineral sciences and engineering with finance and economics in the analysis of appropriate questions facing the minerals and energy industries. Its practitioners include those trained in the earth sciences; mining, petroleum, and geological engineering; metallurgy and mineral preparation; as well as finance, information systems, economics, and statistics-most usefully in one or more combinations. Allowing for some overlap, three general areas may be identified: evaluation, economic analysis, and resource appraisal. Evaluation begins with mine investment analysis (exemplified by Gentry and O'Neil, 1984) and process costing, for which the STRAMM Handbook (Anon., 1977) provides a well-known basis for mining and beneficiation. But it extends from property appraisal, often used for the determination of taxes and royalties, through the determination and comparison of transport costs (e.g., Richer and Soo, 1977), and to benefit/cost analyses of externalities. Economic analysis, the subject of this section, is displayed in rigor and extent both theoretically and as applied to commodity classes in Vogely (1985), but it is implicit though apparent throughout Lefond (1983). The text edited by Vogely places minerals in their aggregative context with economic growth and trade, proceeds to the theoretical analysis of minerals and their markets, analyzes the structure and performance of the major mineral sectors, and concludes with policy issues: fuel, nonfuel, and environmental. Resource appraisal employs quantitative methods for the estimation of mineral and energy resources. It moves through geologic, geophysical, and geochemical properties to the identification of estimation procedures for mineral endowment and for the economic measure of stocks and flows of specific minerals (Harris, 1984). It can be used to estimate the probable amount of a specific resource remaining in a given region and has been used to project sites in a specific

Jan 1, 2008

1. Domestic Production and Use: In 1974 twelve companies operated 31 primary aluminum reduction plants, three firms accounting for 64% of production. Washington, Oregon, and Montana accounted for 32% of the total production; Gulf Coast States, 24%; Northern States, 33%, and other Southern States 11%. Output of primary metal in 1974 was valued at $3.4 billion. About 80% of the secondary recovery was from new aluminum base scrap and 20% was from old scrap. Aluminum consumption by 25,000 firms was centered in the East Central United States. Of aluminum consuming industries in 1974, building accounted for about 27%; transportation 19%; electrical, 13%; packaging, 15%; and consumer durab1es, 9%.

Jan 1, 1975

1. Domestic Production and Use: In 1975.12 companies operated 31 primary aluminum reduction plants, with 3 firms accounting for 67% of production capacity. Washington, Oregon, and Montana accounted for 37% of the total production; Gulf Coast States 21%, Northern States 29%, and other Southern States 13%. Output of primary metal in 1975 was valued at $3.0 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Of aluminum consuming industries in 1975, building accounted for about 21%; transportation 19%; electrical 14%; packaging 18%; and consumer durables, 9%.

Jan 1, 1976

This briefing was sponsored by the Bureau of Mines to summarize ongoing and recently completed chromium-chromite research and resource assessment activities by the Bureau. Through the series of 18 presentations compiled herein, Bureau personnel covered a wide range of topics including U.S. chromite and chromium trends and usage patterns; foreign and domestic resources; and research activities on mineral characterization and beneficiation, chemical and pryometallurgical processing of chromite and chromium-bearing wastes, new low-chromium alloy and coating substitutes, corrosion- and oxidation-resistant stainless steels, and chromium-containing refractories.

Jan 1, 1986

The U.S. economy continued to expand during 1986, although at the slowest pace since 1982 when the current business expansion began. Real gross national product (GNP) grew about 2.6%, slightly below 1985 growth but significantly below that of 1984. The continuing expansion was fueled predominantly by rising personal consumption expenditures as well as growing government purchases of goods and services. Fixed investment, although positive, failed to grow at the rate of the overall economy. The trade deficit, which increased more than 30% over the record 1985 level, continued to depress economic growth despite significant declines in the price of petroleum and the value of the dollar. On a more positive note, domestic employment continued to grow--increasing over 2 million from the 1985 level--and inflation and interest rates declined. The unemployment rate dropped slightly to 7.0%. Of direct importance to the minerals-producing industries, expenditures for consumer and producer durables as well as investment in residential construction each grew faster than the overall economy, but investment in nonresidential structures fell more than 10% from the 1985 level. The low level of real capital spending declined about 3% in 1986, following strong gains in 1985 and in 1984. Capital expenditures for new plant and equipment bottomed out in the second quarter and expanded in the third and fourth quarters. The decline in the first half of the year was partially attributed to uncertainty arising from the then-proposed tax bill. Also, there was little impetus for corporations to invest in new capacity since factories were operating at less than 80% of capacity during most of the year, in part because of continued competition from imports.

Jan 1, 1987

By Owens S. Roberts

The drive selected for any piece of machinery must adequately satisfy the application requirements both during the starting interval and at running conditions, All loading possibilities of the drive must be known and allowances made for any adverse limiting conditions such as extreme cold, or perhaps an intermittent excessive loading situation etc. In general, the drive must be selected to provide the required operating characteristics with maximum reliability and at minimum cost. Simplicity of overall design is always an advantage and care must be exercised to insure that systems incorporating unnecessary complicated parts are not indiscriminantly provided. Important non-technical considerations such as equipment avail-ability (on an overseas project) as well as standardization details also play a role in the drive selection process. Additionally, an assessment of the potential capabilities of the personnel that will have to maintain the equipment can have some influence on the final choice. Several types of prime movers are available but this article will restrict itself to the use of induction motors operating from an available alternating current power source. Many drive arrangements are possible, the most common being the direct coupled single motor arrangement. It is sometimes desirable to use more than one motor per machine, but these designs are usually more

Jan 1, 1971

By Eldon Keith Stanek

This annual report deals with a multi-faceted research effort to increase mine electrical system safety. The project can be broken down into six task areas. Task one deals with the development of tests and instrumentation to perform these test- that are designed to detect incipient faults on mine power systems. This program also encompasses evaluation of the tests and automation of data collection and recording using a microprocessor. Task two concerns the prediction and suppression of mine electrical transients. This program involves digital simulation and suppression hardware evaluation. Task three deals with the reliability and fail safe assessment of various components of the mine electrical system including both the protective system and bulk power system components. Task three deals with theoretical analysis, laboratory testing and in-situ testing in coal mines of power system devices. Task four is an effort to design an optimal mine electrical distribution system. The initial effort is along the lines of refining analytical tools such as the load flow model. Task five is an attempt to optimize the selection of molded case circuit breakers makes or models on the basis of total annual cost. Task six assesses the availability of equipment to satisfy existing federal regulations.

Jan 1, 1977

By D. Berkley

The competitive pressure, the increasing energy costs and the environmental regulations impose substantial challenges to the definition of power plants serving industrial facilities. Primary mining and metallurgical facilities have even greater challenges because they are often located remotely, where the fuel supply can be a problem. The absence of a power grid imposes challenges on the reliability and quality of the electrical energy supply. In addition, the facilities usually require thermal energy too, not only electricity. This paper outlines these types of issues that have to be considered when defining a cogeneration plant integrated with a remote located industrial facility. It is addressed to the ?users? of cogeneration facilities rather than to ?generators.? The focus is on analyzing various site-specific design considerations to pre-screen the feasible cogeneration alternatives and minimize the number of options to be analyzed from the economics viewpoint. This approach could substantially reduce the engineering effort and schedule during the feasibility phase of the project. Part 1 of this paper (Berkley, 2003) provides a basic understanding of cogeneration plants of various types to establish a common language. Part 2 outlines and analyzes specific issues that could be of help in the definition of cogeneration installations for remotely located industrial facilities, with a focus on mining and primary metallurgical plants.

Mar 1, 2003

By E. J. Kloos

One phase of the work of the Bureau of Mines in health and safety is promoting the use of safe, satisfactory, and reliable respiratory-protective devices. To insure that such devices will be available, the Bureau has established schedules of minimum-performance requirements for the approval of self-contained breathing apparatus (1),4/ gas masks (2), supplied-air respirators (hose masks, air-line respirators, and abrasive-blasting helmets, hoods, or masks) (3), dispersoid (dust, fume, and mist) respirators (4), and nonemergency gas respirators (chemical-cartridge respirators) (5). Approval tests of self-contained breathing apparatus are conducted by Health and Safety District B; approval tests of other types of respiratory-protective devices are conducted by the Branch of Health Research. Manufacturers of respiratory-protective devices may submit their equipment to the Bureau of Mines for approval under the requirements of these schedules. If the device, when tested by the Bureau, meets the schedule requirements, a certificate of approval will be granted, which not only states that the equipment has passed the schedule requirements but also gives information about the limitations of the device. If it is found at any time that approved devices do not meet the requirements of the pertinent schedule, the Bureau may rescind approval.

Jan 1, 1959

By D. M. Steelman

Digital systems have been employed in industry as an aid in process evaluation and control for about 20 years. The earlier systems were quite simple and did little more than periodically scan a multitude of process variables, perhaps comparing them to alarm limits, and print out the results. As time passed, the needs of industry and the imagination of process engineers became more demanding. Rather than perform only alarm checking and logging, operating guides were generated to help the operator gain optimum performance from the process. Eventually, systems were entrusted with the job of manipulating the set points of the local analog control loops in a (DDAC) digitally directed analog control mode. Today digital systems are used to gather all-the process information, including both analog and digital variables; to make the necessary data manipulations; and to control the process end elements in a (DDC) direct digital control mode. During these years of transition from the very simplest systems to the complex systems of today, the demands upon the system engineer have been every increasing. The process engineer has required, among other things, more computational ability at high speeds, faster input and output rates, greater flexibility, better communication facilities (man-machine interface), (process oriented software), and finally, greater reliability at lower cost.

Jan 1, 1969

By William R. Bond

The pressure/vacuum lysimeter is being used as an effective vadose zone monitoring device for mining heap leach facilities, tailing disposal ponds and tailing waste sites. Their use has proven reliable for baseline data collection, early warning leakage detection and analyzing geochemical variations in the vadose zone. The lysimeter structure utilizes a closed cylindrical chamber made of PVC or inert material. The soil water intake portion of the cylinder is made of a porous material of low permeability. The application of vacuum or pressure to the unit is via two access tubes from the ground surface. Available soil moisture is drawn by vacuum through porous material into the lysimeter chamber and then collected from the access tubes. Case studies show their usefulness for monitoring around a uranium tailing pond constructed in glacial till material, under heap leach pads and pregnant, barren, and overflow ponds, and investigating the movement of contaminant moisture through old tailing deposits. Relatively easy to install and sample, regulatory agencies and facility operators are accepting and negotiating for their application as a site integrity monitoring device and unsaturated zone research tool. Their use at heap leach facilities lends credibility to solution balance calculations when considering a leachate loss of 5 or 10 percent can make or break a mine's profitability.

Jan 1, 1984

By H. R. Hardy

Whether the mining engineer is concerned with stress problems in a mine at depth, the development of a new drill bit, or the efficiency of a comminution process, the mechanical properties of the rock with which he must work are of the utmost importance. One of the most popular topics in rock mechanics circles today is ?Is it possible to utilize directly parameters determined from laboratory tests on rock specimens in the analysis of mining engineering problems?? It is the author's opinion that laboratory and .field investigations have not yet reached the stage of development where this question can be answered with any degree of certainty. At present, great difficulties are involved in applying the results of laboratory tests to a mining engineering problem. However, this is due in part to the lack of detailed measurements of stress and deformation in the field and in part to the lack of development of satisfactory structural theories to correlate laboratory and field measurements. Furthermore, if mechanical properties measured in the laboratory are to be directly applied to the analysis of mining engineering problems, the critical mechanical properties must be identified, reliable test procedures must be developed and extensive test programs must be carried out.

Jan 1, 1964

By D. E. Banks, J. K. H. Ma, Y. Rojanasakul, J. Y. C. Ma, C. J. Malanga

There is evidence to suggest that cell injury induced in alveolar macrophages (AM) following phagocytic activation by silica particles may be mediated through changes in intracellular free calcium [Ca 2+}. However, the mechanism of silicainduced cytotoxicity relative to [Ca2+], overloading is not yet clear. To provide a better insight into this mechanism, isolated rat AMs were exposed to varying concentrations of crystalline silica (particle size< 5 µm in diameter) and the fluctuation in their [Ca2+]; and cell integrity were quantitatively monitored with the fluorescent calcium probe, Fura-2 AM, and the membrane integrity indicator, propidium iodide (Pl). Results from this study indicate that silica can rapidly increase [Ca2+]; in a dose-dependent manner with a characteristic transient calcium rise at low doses (<0.1 mg/ml) and an elevated and sustained rise at high doses (>0.1 mg/ml). Depletion of extracellular calcium [Ca 2+]0 markedly inhibited the [Ca2+]; rise (˜90%), suggesting that Ca2+ influx from extracellular source is a major mechanism for silica-induced [Ca2+]; rise. When used at low doses but sufficient to cause a transient [Ca2+]; rise, silica did not cause significant increase in cellular Pl uptake during the time of study, suggesting the presevation of membrane integrity of AMs under these conditions. At high doses of silica, however, a marked increase in Pl nuclear fluorescence was observed. Depletion of [Ca 2+] 0 greatly inhibited cellular Pl uptake, induced by 0. 1 mg/ml or higher doses of silica. This suggests that Ca 2 + influx, as a result of silica activation, is associated with cell injury. Indeed, our results further demonstrated that the low dose effect of silica on Ca 2+ influx is inhibited by the Ca2+ channel blocker nifedipine. At high doses of silica (>0.1 mg/ml), cell injury was not prevented by nifedipine or extracellular Ca2+ depletion, suggesting that other cytotoxic mechanisms, i.e., nonspecific membrane damage due to lipid peroxidation, are also responsible for the silica-induced cell injury. Silica had no significant effect on cellular ATP content during the time course of the study, indicating that the observed silicainduced (Ca2 ... ); rise was not due to the impairment of Ca2 + -ATPase pumps, which restricts Ca2+ efflux. Pretreatment of the cells with cytochalasin B to block phagocytosis failed to prevent the effect of silica on [Ca2+]; rise. Taken together, these results suggest that the elevation of [Ca2+]; caused by silica is due mainly to Ca2+ influx through plasma membrane Ca2+,channels and nonspecific membrane damage (at high doses). Neither ATP depletion nor Ca2+ leakage during phagocytosis was attributed to the silica-induced [Ca2+]; rise.

Nov 1, 1995

By Robert Mensah-Biney

The loading characteristics of gold-tetrabromide species onto a weak-base resin, PAZ-4, were evaluated using a completely mixed batch reaction system. The time. to attain equilibrium loading was substantial, on the order of several days. However, abnormally high loading capacity values of 15 to 20 meq Au/g dry resin (1000 to 1300 kgAu/tonne) were attainable in 24 hours. The loading of gold-bromo species by P AZ-4 was visualized as consisting of two processes: (i) the rapid adsorption of [AuBr4r species by simple ion exchange mechanisms and (ii) reduction of [AuBr4r to metallic gold by an electron exchange mechanism. Elution of gold from loaded resin was feasible provided the resin had not been loaded to high capacity values. If loading is carried to high levels, complete elution becomes impractical and the gold may be recovered by ashing the loaded resin. For the high loading capacities observed this option would appear to be cost effective.

Jan 1, 1991

By S Robinson, A Turner, R Dale, C Butler

"Sandfire Resources NL- (‘Sandfire’) DeGrussa definitive feasibility study (DFS) identified geometallurgy as a major factor in achieving optimum plant performance at the DeGrussa mine. A geometallurgical initiative was created to proactively investigate this issue, and a key initial achievement was the 2013 paper by Condon et al (2013) on developing a working geometallurgical model from first principles. Significant advancements in Sandfire’s geometallurgical understanding since that publication now shape how information is presented and communicated.The main geometallurgical parameters so far identified as critical factors affecting plant performance are Cu:S ratio, iron sulfide mineralogy, talc carbonate content and sphalerite content. Apart from specific mill strategies, geometallurgical issues have been managed through communication between departments and strategic run-of-mine (ROM) pad management.This paper uses the current theories of geological evolution of the volcanogenic massive sulfide (VMS) deposit at DeGrussa, to discuss the variability between the orebodies C1, DeGrussa (sea floor mounds) and C4, C5 (sub-sea floor replacement) to highlight the different issues each orebody is expected to encounter when processing.A zone of altered low-grade mineralisation surrounds the main orebodies at DeGrussa, referred to as a halo. Talc minerals are often patchy within this halo and often cause significant recovery issues during processing. This halo has been successfully modelled using MgO as a proxy. The ability to model the talc material assists with both identifying potentially problematic zones for processing and geological interpretation of the ore deposits evolution.Early in geometallurgy studies at DeGrussa it became apparent that it would be useful to identify processing performance prior to mining. This necessitated the incorporation of specific sulfide species into the mining block model. These attributes are interpolated from the logged sulfide estimates allowing a clear picture of the abundance of each mineral type within a defined area.In conjunction with the block model a geometallurgical factor (GMF) graph was developed, identifying sulfide mineralogy based upon mineral assays. These two recent additions to the model provide a clear picture of the nature of the ore sources that will be presented to the processing plant.The future of geometallurgy at DeGrussa will see these tools used to aid mine scheduling with a view to further improve processing recoveries.CITATION:Butler, C, Dale, R, Robinson, S and Turner, A, 2016. Geometallurgy – Bridging the Gap between Mine and Mill: a Case Study of the DeGrussa Geometallurgy Program, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 77–88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Batric Pesic

Reactions of metallic iron were studied in several different aqueous solution systems: water, medium salt solution used for the growth of T ferrooxidans, ferric iron solution and solution containing T ferrooxidans. Each system was studied under abiotic and biotic conditions in the presence of T ferrooxidans and as a function of pH, particle size of iron powder, temperature, ferrous and ferric iron concentrations. It was found that metallic iron reacts with water differently than does with ferric iron in water. Surprisingly, T ferrooxidans were non-functional in the dissolution of metallic iron. Also, the reactions of metallic iron with pure water were indistinguishable from the reactions with water containing medium salts for bacterial growth. The reactions with ferric iron were also independent of medium culture compounds. The mechanisms of metallic iron reactions with ferric ions are different from the mechanisms of metallic iron reactions with water.

Jan 1, 2001

By K. V. Raj

As open pit mines continues to grow deeper, managing air pollution can become challenging. During arctic air inversion, the temperature of the air over the mine increases with altitude, and the cold, heavy, surface air is trapped in the pit. This problem is complex, and any solution will require an extensive understanding of the interactions between the aerodynamic movement of air, air inversion, meteorology, pollutant sources, and transport phenomena in the open pit mines. The availability of computational fluid dynamics (CFD) has elucidated the pollutant flow mechanism in open pit mines. Very few CFD studies have been published, especially the Large Eddy Simulation (LES), on the contaminant transport in deep open pit mines under arctic air inversion. The contaminant transport in an open pit mine under arctic inversion is due to a stable or nocturnal boundary layer in micro-meteorological terms. Understanding the physics of the stable boundary layer (SBL) is relevant to air flow and pollutant transport in deep open pit mines. This paper focuses on a Large Eddy Simulation (WMLES as Sub-Grid Scale Model) modeling of the SBL and pollutant transport in a large open pit mine.

Feb 23, 2014

By A. A. Hejja

The effect of composition on electrical conductivity, viscosity and liquidus temperature of the slags was investigated in the temperature range of 1300" to 1450°C. The synthetic slags containing CaO, MgO, SiO,, A1,0, and FeO were similar to those employed in the electric furnace smelting of sulphide Cu-Ni concentrates containing PGM (Platinum Group Metals) from the Merensky Reef of South Africa. FeO and SiO, were found to affect the viscosity and conductivity the most while liquidus temperature depended on MgO content in addition to these. The activation energy for electrical conduction was found to vary from 67 to 159 kJ/mol and that for viscosity from 125 to 209 kJ/mol. Optimization of the slag composition was attempted on the basis of opposite trend of the viscosity-electrical conductivity relationship with slag composition.

Jan 1, 1994