Search Documents

By Martin D. Larisch

The construction of diaphragm walls and most large-diameter bored piles (piers) is often carried out under drilling support fluids to temporarily stabilise the excavation prior to concrete placement. In most cases such fluids are either mineral-based slurries (bentonite) or polymer support fluids. The working mechanisms of these two fluid types are fundamentally different. Designers need to consider possible fluid-related impacts on the permanent design performance of the project-specific deep foundations as well as for the temporary excavation stage during construction. Robust design methods for bentonite slurry-supported excavations have been developed in the last few decades and the working principles and associated risks of such mineral-based slurries are understood reasonably well. However, such meth-ods have not been developed in detail for polymer-based drilling fluids. This document provides a brief overview of the main characteristics of bentonite- and polymer-based drilling fluids as a guide for construction practitioners and design engineers alike. The paper also high-lights some common construction risks related to casing installation and the selection of suitable fluid systems for different ground conditions. Typical defects caused by the incorrect application of drilling support fluids, and their pro-active mitigation, are discussed, too. In addition, the basic concepts of sta-bility calculations for bentonite fluid-supported deep excavations are briefly introduced and their ap-plicability for other fluid types such as polymer-based support fluids or water are reviewed.

Nov 1, 2022

By Aleksandar D. Bugarski, Dylan A. Ritter

The results of laboratory characterization of tailpipe emissions for three “clean” engines that meet U.S. EPA Tier 4 final emissions standards were used to assess the viability and effectiveness of repowering existing engines and powering new mobile equipment with those engines as a control strategy for reducing exposure of underground miners to diesel aerosol and criteria gases. The evaluated engines were representative of those that achieve the emission standards through implementation of various in-cylinder emissions control strategies, use of crankcase filtration, and use of three types of exhaust aftertreatment systems: (1) diesel oxidation catalytic converter (DOC), (2) combination of DOC and the full-flow wall flow monolith diesel particulate filter (DPF), or (3) combination of DOC, diesel exhaust fluid (DEF) based selective catalytic reduction (SCR) system, and ammonia slip catalyst (ASC). The study showed that the highest reductions in concentrations of diesel aerosols in underground workings, in terms of both mass and number, could be achieved if the engines, preferably in all power classes, are fitted with viable DPF systems. The use of U.S. EPA Tier 4 final engines equipped with DOC and DOC/SCR/ASC systems could help operators to considerably reduce mass, but not number concentrations of aerosols. The emissions of two of the evaluated engines, one equipped with DOC and the other equipped with DOC/DPF systems, were characterized by substantial secondary NO2 emissions that would limit the viability of those engines for underground mining applications. It appears that the catalyst formulations used in the exhaust aftertreatment systems of the “clean” engines marketed to the underground mining industry need to be formulated to minimize the potential for generation of secondary NO2 emissions. The results indicate that the engines fitted with viable SCR/ASC systems present a low-NO2 alternative. All three “clean” engines were found to have low CO output. Therefore, due to nuances associated with the use of diesel-powered mobile equipment in underground mines, special attention needs to be paid to the selection and potentially optimization of “clean” engines for underground mining applications.

Feb 1, 2025

By George P. Demopoulos

In this paper the production and stability of crystalline scorodite (FeAsO4·2H2O) is discussed both on the basis of previously published work as well as recent work performed in our laboratory. The production of scorodite, especially from arsenic-rich and iron-deficient sulphate solutions offers a number of operational advantages such as high arsenic content, stoichiometriciron demand, and excellent dewatering characteristics. In addition to hydrothermal production of scorodite the work done over the last 10 years in our laboratory has determined that it is feasible to produce scorodite by step-wise lime neutralization at 90°C. The atmospheric scorodite possesses the same structural and solubility characteristics with the hydrothermally produced scorodite. Long term equilibration tests (up to 66 weeks) in the pH range 5 to 9 and temperatures from 22 °C to 75 °C revealed scorodite to undergo slow incongruent dissolutionyielding a highly metastable nano-sized 2-line ferrihydrite phase. The equilibrium arsenic concentration with this phase was 0.35, 0.96 and 5.87 mg/L at pH 5, 6, and 7 respectively at 22°C. In the presence of gypsum slightly lower concentrations were measured, this being more pronounced at pH>7. It was tentatively deduced that a Fe-Ca-AsO4 association (in the form of a phase resembling the mineral yukonite) contributes to the lowering of As concentration. Finally thermodynamic calculations determined that scorodite is stable in the presence of ferrihydriteunder oxic conditions up to pH 6.75 at 22 °C or higher pH at lower temperature and gypsum-saturated solutions. Keywords: Scorodite, Crystallization, Arsenic, Solubility, Stability, Precipitation, Disposal, Extraction, Processing, Metals, and Environment.

Jan 1, 2005

By Kenneth G. Skinner, Hewitt Wilson, Thomas L. Hurst

Although chromite deposits occur in California , Oregon, Washington, Montana, Wyoming , Pennsylvania, Maryland , New Mexico , North Carolina, Alaska, and the Phillippine Islands , less than 1 percent of the ore used in the United States is obtained from these deposits . Most of the ore in peacetime has been supplied by imports from South Africa, New Caledonia, Turkey, and Cuba . The mineral chromite , the most important chromium ore , is an isometric spinel with an ideal composition of FeO Cr2O3 , but commercial chromite has the variable composition (Fe , Mg) Oʻ (Cr , Al , Fe) 203. Chromite has a black color , a specific gravity of 4.4 , and a hardness of 5.5 . In thin section the color is reddish -brown to black . Chromite occurs in dunite and pyroxenitic ultrabasic rocks , which are composed of iron- magnesium silicate minerals such as olivine , saxonite , serpentine , and enstatite . These are also the gangue minerals . Com mercial ore occurs at random in the country rock in kidney- or lens - shaped deposits , which have no apparent relationship to each other . Stringers , veins , and bands often cut the country rock without regard either to fracture or to other deposits . Some beach sands , such as those in southern Oregon, contain chromite .

Mar 1, 1943

By C. E. Wicks, F. E. Block, F. D. Stevenson

The vapor pressures of tungsten (VI ) chloride ( WC1 ) and hafnium ( IV ) iodide ( HFI ) were measured by a metal diaphragm technique . Vapor pressure values were obtained to permit calculation of the thermodynamic properties of the vaporization processes of the compounds . The vapor pressure data of WC16 are represented by the following equations for the liquid , B - solid , and a- solid over the temperature intervals indicated : - log P = 8.194 3,253 /T Liquid , 281.5 ° to 325 ° C : B - solid 230.0 ° to 281.5 ° C : log P a - solid 185.0 ° to 230.0 ° C : log Pam *** = 8.794 - 3,588 / T = 9.615 - 3,996 /T where T is the absolute temperature in degrees Kelvin . The heats of vaporization and sublimation are 14.9 , 16.4 , and 18.3 kcal / g mole , respectively . The entropy of vaporization at the normal boiling point , 330 ° C , was 24.3 eu . The fusion temperature , 281.5 ° C , and transition temperatures , 230.0 ° and 185 ° C , were found by thermal analysis .

Jan 1, 1964

By S C. Dominy

For any gold deposit-based geometallurgical study, the collection and processing of representative samples for gold grade and recovery tests is critical. Sampling protocols should be designed to suit the style of orebody in question. The proportion and size of gold particles has a direct impact on the effectiveness of sampling protocols and metallurgical recovery processes employed. Studies focussing on ore mineralogy and gold particle deportment, size and distribution are required. Key issues are the presence of gold particle clustering (important for sampling optimisation) and proportion of coarse versus fine to refractory gold. X-ray computed tomography (CT) is a radiographic technique that produces high-resolution 3D computerised models of objects based on density distribution. The ‘virtual’ specimens are made up of voxels, the 3D equivalent of pixels each assigned a grey value based on X-ray absorption. This paper presents the results of recent research on the imaging of in situ gold particles in a coarse gold-bearing ore. The technique shows promise as a rapid non-destructive method for preliminary characterisation to facilitate more detailed studies. Early and rapid gold particle determination enables sampling protocol optimisation and metallurgical recovery parameters to be defined prior to detailed feasibility studies

Sep 5, 2011

By Stanley J. LeFond

Brazil is one of the most outstanding examples of economic development of our time. Its amazing growth record is substantiated by a GNP which has increased at an average rate of 92% for the period 1968-1970 and estimates for 1971 range from 11.7-12.5%. Hence, this growth, coupled with a more relaxed attitude of the Brazilian government towards foreign participation in business opportunities and the remittance of profits out of the country, has caused many exploration companies to reevaluate the potential of Brazil. Despite recent press notices and publicity, Brazil is still not a mining country in the tradition of Canada or Australia. It is still basically an agriculture and manufacturing country.

Jan 11, 1973

By Sunny Murmu, Gnananandh Budi

One of the most significant concerns in longwall ground control is the instability and failure mechanism of the coal wall. The current research uses FLAC3D to simulate panel 1 of the Adriyala Longwall Project, India, in order to evaluate the distribution of vertical stress and material failure mode, in and around the longwall face. Additionally, three distinct criteria are used to evaluate coal wall spalling: vertical stress distribution, maximum shear strain, and residual cohesion. A novel algorithm is also proposed to appropriately capture roof bed caving, shield installation and advancement, and coal extraction from the face. The findings of the modelling show that progressive longwall extraction creates an elliptical stress relief zone around the excavation void. During the peak stress phase, the height of the stress relief zone is greatest, whereas the width is highest during the main fall phase. As mining advances, the coal wall at the face line appears to lose its stress-bearing capability. Shear failure was the most common coal wall failure mode. Maximum spalling depth (MSD) and longwall face spalling index (LFSpI) were used to measure the extent and volume of coal wall spalling in FLAC3D. For panel 1 of the ALP mine, the MSD, and LFSpI were determined to be 3 m and 90.5 %, respectively. The mode of coal wall spalling was expected to be total or fragmented failure. The field observations and the numerical modelling findings were in good agreement. The compressive strength and deformation modulus of the immediate roof appear to have a substantial role in coal wall spalling. The results of the proposed numerical simulation exercise can help strata control engineers better detect the risks of coal wall spalling and enhance face control for safe and productive working environment at the longwall face.

Aug 8, 2023

By Erik Sundström, Magnus Nygren

Having seen significant improvements to accident rates in the last 40 years, companies in the Swedish mining industry now show a greater focus on the development of safety cultures throughout their organisations and workplaces. However, there is a lack of research examining the different safety initiatives and strategies practiced in the industry today. This study explores the potential influence and consequences such initiatives may have on the development of safety cultures in the Swedish mining industry. Twelve interviews with experts on safety initiatives from four different Swedish mining organisations were conducted and analysed in a process based on qualitative thematic analysis to identify notable connections to safety culture development. The results of these interviews highlight proclivities in the implementation and use of safety initiatives such as subjects of focus, methods and desired effects. This enables the interpretation of the conceptualisation and methods for the development of safety culture in these organisations based on their approaches to safety development. We believe the results of this study can serve as support for discussions on safety culture development in the Swedish mining industry, and be of interest for international mining industries, in addition to approaches to research in this field. However, we also believe it is important to emphasise the opportunities to approach safety culture in mining from different perspectives than those common today.

Jul 19, 2023

By Zhibiao Guo, Jinglin You, Dongshan Yang, Yuanxin Zhao, Yuhui Li, Jingwei Gao

By utilizing collapsed gangue to create gob ribs, roof cutting and roadway maintenance (RCRM) technology enables coal pillar-free mining, presenting a novel approach. Due to their inherent structure, faults, which are common geological formations, can lead to various hazards, including fault sliding and significant deformation of roadways. In this study, a selfdesigned underground engineering simulation test device is utilized to imitate the cross-fault mining of the 11,101 working face in the Qipanjing Coal Mine (East). The objective is to examine the behavior of the surrounding rock and stress evolution. Generally, the experimental findings demonstrate that compared to the return air roadway, the RCRM roadway experiences a 3.3% decrease in maximum coal rib stress. This suggests that the implementation of this technique can effectively alleviate the stress on the surrounding rock of the roadway. The maximum coal rib stress, lateral pressure of the gob rib, and maximum deformation of the roof near the fault of the RCRM roadway are 11.3%, 25.6%, and 86.1% greater than those of the conventional geological conditions, respectively. The roadway deformation is negatively impacted by the fault structure. Based on experimental data and field measurements, a discrepancy in the maximum roof deformation between the test and field monitoring results under typical geological conditions is 8%. This indicates a favorable alignment between the test results and the real-life scenario. In conclusion, the proposed targeted control technique is implemented in the field by integrating the mining invariant equation and gangue volume expansion equation. This not only validates the effectiveness of the technology but also offers valuable insights for the future utilization of RCRM technology under comparable circumstances.

Feb 20, 2024

By S. Chatterjee, F. Suparno, A. Paithankar

Estimating reserves and quantifying resources stand as pivotal and intricate endeavours within the realm of coal mining operations. Intricate geological formations compound the challenges in resource estimation, thereby complicating reserve calculations. The uncertainties tied to geological attributes of coal, encompassing parameters like tonnage and coal quality, wield significant sway over resource and reserve computations within coal mines. This research delves into the domain of geological uncertainties, with a specific focus on calorific value, aiming to numerically characterise resources and reserves within an open-pit coal mine situated in Indonesia. To quantify resources, the coal seam geometry underwent simulation via a multipoint geostatistical technique known as single normal equation simulation. A geologically established coal seam served as the training image for generating 20 equiprobable coal models. To simulate CV, 50 realisations were generated for each simulated coal seam, utilising sequential Gaussian simulation. Deviations of the simulated coal seams ranged from -0.07% to 5.48% in comparison to the training image. The CV simulation yielded an average value of 5,920.29 kcal/kg, accompanied by a standard deviation of 586.54 kcal/kg. However, the average CV spanned from 5,305.26 kcal/kg to 6,526.55 kcal/kg across diverse simulations. For reserve calculation within the context of geological uncertainties, an algorithm rooted in maximum flow graph theory was employed to construct the ultimate pit for the coal mine. Within this final pit, the average stripping ratio was 1.62, coupled with a CV value of 6,019.66 kcal/kg. When juxtaposed with the deterministic model, the findings underscore that the stochastic ultimate pit delineates a more expansive excavation, accompanied by a heightened undiscounted cash flow.

Oct 2, 2025

By J. Swanepoel, J. H. van Laar, J. C. Vosloo, W. A. Pelser

Deep-level underground mining costs in South Africa are continuously rising due to the increased depth at which gold is being mined, resulting in a rise in virgin rock temperature and an increase in cooling requirements. Therefore, mines must evaluate various ventilation and cooling optimisation projects required to be implemented throughout their life of mine (LOM). This study develops a method to identify and prioritise large capital expenditure (CAPEX) underground environmental improvement projects, to improve thermal comfort underground. The solution presents a ‘multi-criteria decision-making’ (MCDM) process, incorporating the ‘analytic hierarchy process’ (AHP) and the ‘technique for order performance by similarity to ideal solution’ (TOPSIS) into the method to provide for scientific decision-making. These projects are evaluated based on four criteria, namely project risk, the impact on the underground thermal comfort, cost, and implementation time. This study’s solution uses ventilation simulations to determine the impact of the projects on the underground environment. The identification and evaluation of an environmental improvement project to best suit the current economic climate, while improving underground conditions and decreasing the safety risk is an essential aspect of the solution developed in this study. The method was implemented on a mechanised deep-level underground mine and showed that surface refrigeration is the most suitable alternative, which was implemented at the case study mine as validation of the developed solution. The study proves that the MCDM method is an adequate solution to incorporate subjective criteria into the decision-making process, resulting in a scientific and structured approach to making significant and complex decisions.

Feb 17, 2023

By S. Kouniali

Experience with knowledge-based systems for Layout planning and roadway support dimensioning is on hand in European coal mining since 1985. The systems SOUT (support choice and dimensioning, 1989), SOUT 2, PLANANK (planning of bolt-support), EXOS (layout planning diagnosis. 1994), Sout 3 (1995) have been developed in close cooperation by CdF1. INERIS2. EMN3 (France) and RAG 4, DMT5, TH - Aachen6 (Germany); ISLSP (Integrated Software for Layout and support planning) development is in progress (completion scheduled for July 1996). This new software technology in combination with conventional programming systems. numerical models and existing databases turned out to be suited for setting-up an intelligent decision aid for layout and roadway support planning. The system enhances reliability of planning and optimises the safety-to-cost ratio for ? deformation forecast for roadways in seam and surrounding rocks, consideration of the general position of the roadway in the rock mass (zones of increased pressure, position of operating and mined panels). ? support dimensioning ? yielding arches, rigid arches, porch sets, rigid rings, yielding rings and bolting / shotcreting for drifts ? yielding arches, rigid arches and porch sets for roadways in seam ? bolt support for gateroads (assessment of exclusion criteria and calculation of the bolting pattern) ? bolting of face-end zones (feasibility and safety assessment, stability guarantee).

Jan 1, 1996

By S. Yamashita

Recently in Japan, unexpected degradation (surface subsidence) at old underground quarry sites, such as 'Ohya-Ishi' (pumice tuff) pit field has often been occurred. At these quarry sites, the excavation was started 20 or 30 years ago with mechanical chain cutter and the Room and Pillar method, and stopped 7 or more years ago. Therefore, a reliable method has been required for an estimation of long term mechanical properties of the rock and for an observation of a stability of rock-pillars or structures. In this study, creep tests under uniaxial compressive load were carried out on the 'Ohya-Ishi', with the aim of estimating the long term stability of the rock. From these results, a creep mechanism of the rock was discussed using the failure mechanism hypothesis proposed by Bieniawski and by others. On this basis, critical time to failure was predicted by the relationship between the logarithm of life time and stress ratio of the sustained axial creep load. Additionally, outline of the monitoring system of AE/MS activity in the field, which have set by the Ohya Aria Consolidate Public Corporation and the others to predict or to prevent the degradation of those residual pillars, is to be reported. Key words : Ohya-ishi, Pumice tuff, Mine pillar, Long term stability, Creep, Critical time

Jan 1, 1996

By S. P. Pearton

"Pumpable emulsion explosives have been available to surface and underground massive mining operations for decades, and their unique properties offer significant advantages in terms of improved safety, reliability, and performance. However, the benefits of pumpable emulsions have been unavailable to narrow-reef mining operations due to the lack of technology necessary for their successful implementation in this challenging environment. Despite efforts to promote and enhance the safety and performance of bulk emulsions for narrow-reef stoping, little research has been undertaken to advance the pump technologies required for their implementation. This has resulted in a gap in knowledge and technology, and as a consequence the successful implementation of a pumpable emulsion system has consistently eluded the narrow-reef environment.The purpose of the following investigation was to evaluate the viability of pumpable emulsion explosives for use in South African narrow-reef mining operations. By approaching the problem from multiple perspectives, this research aimed firstly to propose a theoretical framework and suite of equipment suitable for the implementation of pumpable emulsions within the narrow-reef environment. Through the development of this suite of pumpable emulsion technology, tests could be undertaken on the proposed narrow-reef emulsion formulation and pumpable emulsion technology to obtain the necessary understanding of the performance of the system under controlled operating conditions prior to its implementation in the broader mining industry."

Jan 1, 2015

By Joseph L. Buckley

A total of 55 conveyor belt fire tests were conducted in the Bureau of Mines Fire Test Gallery, located at the Factory Mutual (FM) Fire Test Center West Glocester, R.I. The objectives of these tests were to: 1) determine the fire resistance and burning characteristics of various conveyor belt materials under simulated mine conditions; 2) provide essential data for designing a reliable bench-scale conveyor belt fire resistance test; and, 3) determine fire test conditions that will discriminate between low, moderate and high fire resistant materials. Belts, representative of those which mold he found in underground coal mines were examined under n umber of experimental conditions which included; ignition intensity; air flow rate; ratio of belt bright (h2) to overall gallery height (h1); exposure time; and, belt width. It was found that fire propagation could be achieved for some "fire resistant" belts (complying with the present Schedule 2G standard for approval) when exposed to an Ignition source of =6000 Btu/min for a 15-min period at a belt height ratio of 01.66. There appears to be a dependency of flame propagation on air flow rates and belt width, although the tests performed do not provide a quantitative trend. Recommendations are made for additional work to resolve some anomalous date and to fill voids in the rest program.

Jan 1, 1978

By Loren R. Anderson

Traditionally, an evaluation of the safety of slopes has been based on computing a safety factor against failure. In computing the safety factor, the geometry of the slope, the soil parameters and the pore pressures are treated as deterministic quantities even though they are known to be random variables. A pseudo-three-dimensional probabilistic slope stability model has been developed that treats shear strength as a random variable. The model uses the probability of a slope failure as an assessment of slope reliability. The model can accommodate zoned embankments of soil in which the strength is described by the Mohr-Coulomb strength envelope. Autocorrelation functions are used to describe the spatial correlation of the strength parameters, c and tan ø. Model error can also be included in the analysis. The model has been applied to an existing tailings dam and to several hypothetical examples. These examples are presented to illustrate the influence of the choice of the soil strength variability parameters on the probability of failure. The results show that the critical failure surface based on the minimum safety factor is not necessarily the failure surface that will yield the maximum probability of failure. The analysis of the tailings dam shows that variance reduction can be large and that the model error is the dominant source of uncertainty for the embankment analyzed.

Jan 1, 1982

By Paul S. Goodman

This report examines the feasibility of Employee Assistance Plans for the coal industry. Three issues are examined in detail. First, the prevalence of off-the-job factors such as alcoholism, drug abuse, and marital problems are examined in a sample of miners from the eastern, midwestern, and western underground coal fields. Then data were presented that examined the link between these off-the-job factors and behaviors critical to the mines such as absenteeism and turnover. Lastly, we examined the effectiveness of the major Employee Assistance Program in underground coal mining--the HELP Program. The report contains recommendations on whether coal mining companies should implement these programs and how these programs should be designed.

Jan 1, 1986

By S. Johnson

Introduction The mining of aggregates underground has grown steadily over the last 25 years. Growth has come in both production volume and in the importance this segment of the industry is playing in the continuing supply of construction aggregate. Underground aggregate mines will continue to grow in both number of operations and complexity, as the replacement of zoned reserves in metropolitan areas becomes crucial. This growth will result in a shortage of qualified mine managers, possibly limiting the success of these facilities. The aggregate industry will have to modify current practices in order to meet the growing demand for this specialized skill. Segment Growth Underground mining for aggregates is not a new idea. Martin Marietta has been operating underground mines since 1969, and currently operates 16 underground mines ranging in size from 250,000 tpy to 2,500,000 tpy. These mines represent less than 4% of the total number of operating locations, but contributed 9% of the annual production in 2004. Though they range in size and production capacity, the importance is evident. The 2000 United States Census revealed several trends that are of interest to the aggregate mining industry. For the period 1990-2000 the U.S. population grew by 33 million or 13%. There were nine major metropolitan areas with a population of five million or more. These nine areas accounted for 30% of the total U.S. population. More significant was the fact that the population growth in these nine metro areas was 25% of the growth for the entire country. These statistics tell us that the population is expanding in these major metropolitan areas at a staggering rate. The same thing is happening to some degree in every population center. Population growth increases the demand for local aggregate while reducing the available area to mine that aggregate. The need for an economical supply of aggregate to support community expansion is a problem that will grow as older quarries are mined out and closed. This will be an issue that communities of all sizes will have to deal with. A reliable and cost effective supply of quality aggregate is crucial to support community expansion.

Jan 1, 2006

By Karl J. C. Harries

Mineral Agreements and Royalties

Jan 1, 2003