Search Documents

By Douglas D. Donald

The New Jersey Zinc Co. successfully holed through a 2 1/2-mile haulage tunnel connecting its new Ivanhoe shaft with the Van Mater Shaft at Austinville, Va. This 8x 10-ft cross-section tunnel was driven from both ends and met at a point approximately a mile from one shaft and a mile and a half from the other. In order to make certain that the faces met accurately on line and grade it was necessary to refine conventional mine surveying practices. The mines that are serviced by these shafts are located in the southwestern part of Virginia approximately midway between Roanoke and Bristol at the west foot of the Blue Ridge. While the presence of lead-zinc sulfide ores has been known in this area for more than 200 years, it was in 1902 that New Jersey Zinc Co. acquired the Austinville property, which has been in constant operation since that time. About ten years ago the company undertook an extensive diamond drilling program at Ivanhoe several miles to the southwest. This program was successful in locating sufficient ore to justify the purchase of a number of the properties in this area and plans were made to develop the new orebodies. The discovery of this ore as well as substantial addi- tional reserves at Austinville resulted in a decision by the company to increase its daily milling capacity to 3000 tons, of which about 1000 tons would be supplied from the Ivanhoe mine. After careful consideration of all possible methods of transporting this volume of ore from Ivanhoe to the mill, it became evident that diesel locomotive haulage through a 2½-mile tunnel between the two mines would best suit prevailing conditions. Since the lowest operating level, known as the 1100 level, of each mine would be at approximately the same elevation, it was obvious that such a tunnel should be driven on this level. Not only would this tunnel facilitate feeding Ivanhoe ore into the underground crusher and skip loading installation at Austinville, but it would also open up a known orebody 5000 ft southwest of the Van Mater shaft. In addition it would provide a valuable diamond drilling base from which a large and a potentially favorable but untested block of ground might be explored. In order to hasten the completion of the tunnel, it was felt that it should be driven from both ends. ENGINEERING CONTROL PROCEDURES It was vital that the tunnel junction be made accurately on line and grade; thus it was felt that engineering control of an unusually high degree of reliability was required to prevent an accumulation

Jan 1, 1959

By S. Makni, A. Faucher, F. Robichaud, A. Bouajila

"Optimizing the ball charge in a grinding mill may be needed to maximise throughput or alternatively, to achieve proper product size in more challenging situations. Efforts to optimise the ball charge however are essentially empirical and suffer from the lack of appropriate, accessible and reliable tools. To address these limitations, a new model-based technology was developed that relies on 3D Discrete Element Method and population balance techniques: it takes on the form of a simulator that aims to significantly decrease the time required to optimise the size distribution and the grinding media load within a ball mill. This paper summarizes the research work related to the development of this simulator. The calibration of the different constituting sub-models will be highlighted. The successful use of the simulator to predict the effect of ball make-up on the grinding product size distribution in one plant is also reported.INTRODUCTION Adjusting the characteristics of the grinding media charge in grinding mills holds significant potential for optimisation of mill performance. For example, properly adjusting the ball size distribution in a ball mill can help achieving specified targets for final product size distribution and/or throughput capacity. However, several problems appear when reviewing the process and the available tools to optimise ball mill load: • The current empirical simulation tools are lacking with regard to the ability to predict the performance of grinding when changes to mill ball make-up are made; • Generally, these tools estimate the top size of the charge so it is difficult to predict the effect of mixed ball make-up; • As the quality of prediction of these tools is low, the operators try to optimise the ball charge by a ""trial and error"" method and proceeding with conservative changes. The influence of these changes on grinding performance is often less than the measurement precision and the improvements then remain imperceptible; • A change in ball make-up may require an average of about 6 months waiting period before reaching the stationary state of mill ball load. This exercise is due to be costly if applied change decreases the mill performance. In its effort towards the comminution process optimisation, COREM R&D portfolio had addressed the herein described opportunity during the last five years This paper describes the technology already developed for the optimisation of ball charge. It takes on the form of a simulator that aims to predict the evolution of the grinding media load, the grinding energy available in the ball mill and the final product size distribution. The simulator was first validated in a pilot scale ball mill and then applied in an industrial case."

Jan 1, 2012

By D. Rendini, R. D. Gutridge

INTRODUCTION Gwinnett County, Georgia, is a part of the rapidly expanding metropolitan Atlanta Georgia area. Located approximately 48 km (30 miles) northeast of Atlanta, Gwinnett County has a current population in excess of 600,000 and is projected to reach a population of 1,200,000 by 2025. As a part of the County’s master plan to supply drinking water for the expanding population and to increase system reliability, the Gwinnett County Public Utilities Department undertook the Shoal Creek Raw Water Intake and Pump Station Project. Figure 1 shows a vicinity map for the project. Prior to construction of the Shoal Creek Raw Water Intake and Pump Station Project the County had a single raw water intake to feed water from Lake Sidney Lanier (Lake Lanier) into a filter plant for processing into potable water. This project together with a newly constructed water filter plant provides Gwinnett County additional capacity and system redundancy to prevent interruptions to the drinking water supply. Lake Lanier is a man made reservoir with over 800 km (500 miles) of shoreline and was constructed by the Army Corps of Engineers in the 1950s for hydro electric power generation, flood control, and navigation benefits for the Chattahoochee River. Over time, Lake Lanier has become an increasingly important source of drinking water for the metropolitan Atlanta area. This paper focuses on the primary underground construction and lake tap components of the project including a 42.7 m (140 ft) deep pump station shaft 24.4 m(80 ft) in finished diameter transitioning to a 6.1 m (20 ft) finished diameter shaft, a3.05 m (10 ft) finished diameter by 19.8 m (65 ft) deep intake shaft constructed in an average of 21.3 m (70 ft) of water, and a 190.5 m (625 ft) by 3.05 m (10 ft) finished diameter modified horseshoe tunnel connecting the two shafts. This raw water intake system, in conjunction with the incorporated pump station with 8 pumps and dual1,829 mm (72 inch) pipelines, provides a system capacity of 1,091,062 m3/day(240 MGD) to two water filter plants and is expandable by the addition of pumps to1,500,210 m3/day (330 MGD). Parsons provided design and construction management services for the project. The $29.6 million contract to construct the project was awarded to W.L. Hailey &Company. Notice to proceed was given August 6, 2001 and substantial completion was achieved on January 20, 2004. Value engineering changes adopted for the project contributed to completing the project at a final cost of $28.8 million.

Jan 1, 2005

Recent developments in diamond drilling practice have been chiefly 'concerned with modifications in drill design and 'operating technique whereby an increase in daily footage rates and reduced footage costs have been achieved without any marked improvements in the recovery of core. This trend is perhaps due to the general acceptance by the mining and drilling engineer alike of the belief that diamond drilling has definite limitations in exploratory work on mineral deposits characterized by irregularities in continuity and grade, such a belief arising from the fact that drilling technique has not yet evolved coring devices to ensure the full recovery of the rock and mineral formations penetrated.Current diamond drilling operations at Moonta and Wallaroo Mines, carried out by the South Australian Department of Mines, have attained remarkable results in completely eliminating core-loss by the use of a special double-tube core barreI.It is considered that assays of borehole samples taken with this special barrel have a reliability comparable, if not superior to that of similarly situated mine samples and, provided they are spaced satisfactorily, can be used as, a basis for calculating tonnage and grade. Formerly, with only partial core-recoveries, positive borehole results on narrow irregular lodes, such as those in the Moonta and Wallaroo Mines, could be accepted mainly as indications of the presence of mineralization, and could have only a limited bearing on estimates of ore reserves.The value of this special double-tube core-barrel lies In the fact that it guarantees good core recovery and, therefore, good samples, and eliminates the need for sludge-sampling, which is prone to give unreliable assay results from several causes, such as gravity concentration in the bottom of the hole and return water losses which cannot be overcome.In view of the increasing demand for minerals and the probability that the search for them will be carried on largely by boring, it is felt that it would be of interest and value to direct the attention of mining engineers to core-recovery results obtained by diamond drilling plants in South Australia and the features of the special core-barrel, designed by the writer, which has made this possible. Also, the writer is desirous of placing on record two other core-recovery devices designed to extract accurate samples in relatively soft or unconsolidated formations. The latter are used with percussion and calyx plants, respectively and their value has been proven on phosphate rock and coal deposits in South Australia.

Jan 1, 1943

By Rozbeh Moghaddam, William D. Lawson, Priyantha W. Jayawickrama, Hoyoung Seo, James G. Surles

"This study provides calibration of resistance factors (?) for design of driven piles to implement Load and Resistance Factor Design (LRFD) for bridge foundations using Texas Cone Penetration (TCP) Test data. The basic research approach was to compile a database of published full-scale load tests including projects from the Texas Department of Transportation’s (TxDOT) historical archive and projects from neighboring state DOTs. Load test results from neighboring states were leveraged by performing new geotechnical borings with TCP tests at the project sites. The final dataset consisted of 30 load tests performed on precast square concrete piles, with pile widths ranging from 356 to 508 mm and penetration depths ranging from 5.2 to 25.5 m, driven in soils. Ultimate capacities for each load test were interpreted based on Davisson, 5%, and 10% settlement criteria. These measured ultimate capacities were compared against predicted capacities estimated from TCP blow count values (NTCP) and design charts following the procedures outlined in TxDOT’s Geotechnical Manual. From the comparisons, statistical parameters of the biases (??= measured capacity/predicted capacity) such as mean and coefficient of variation were obtained. Resistance factors (?) for LRFD were then determined using Monte-Carlo simulations for each ultimate capacity criteria with the target reliability indices of 2.33 and 3.00.INTRODUCTIONThe Texas Department of Transportation (TxDOT) has used the Texas Cone Penetration (TCP) test since its development in the 1940s. The TCP test is an in-situ penetration test to characterize the materials encountered during geotechnical exploration. Texas currently maintains over 53,000 bridges in the National Bridge Inventory (FHWA 2016), and most of these bridges plus other transportation infrastructure in Texas are supported by foundations designed using the TCP test and its associated foundation design method. The Oklahoma DOT adopted the TCP test and foundation design approach in the 1970s, so the foundations for most of the 23,000 bridges in Oklahoma’s inventory were also designed using the TCP method. With this significant body of experience, the TCP method has been viewed as a straightforward, relatively easy-touse foundation design method that consistently yields safe, serviceable, economical, and maintainable foundations. TxDOT’s deep foundation design method is documented in the TxDOT Geotechnical Manual (TxDOT 2012) and currently employs the allowable stress design (ASD) approach. However, the Federal Highway Administration (FHWA) has mandated that the states begin to implement the LRFD method in place of the older ASD approach (Densmore 2000). This paper presents resistance factors at ultimate limit state (ULS) for design of driven piles using the TCP test, resulting from efforts to be in compliance with the FHWA policy."

Jan 1, 2017

By Patrick J. Williams, Peter J. Pollard

"Abstract - Enigmatic hydrothermal vein/breccia/replacement Cu-Au deposits with magnetite and/or hematite are well-represented in Australian 1850 Ma to 1500 Ma terrains and associated with different-aged synorogenic intrusions in the Tennant Creek Block (ca. 1850 Ma); the Gawler-Curnamona region (1640 Ma to 1590 Ma); and the Cloncurry district (Mount Isa Eastern Fold Belt, 1540 Ma to 1500 Ma with a possible earlier event at ca. 1600 Ma). No deposits are known to be coeval with various 1780 Ma to 1610 Ma anorogenic intrusions. Deposits are hosted by many different rock-types with varying metamorphic grade including granites and various supracrustal rocks. Depth of mineralization varied from many kilometers in semiductile crust (e.g., Cloncurry deposits) to very shallow (e.g., Olympic Dam). Ore deposition near Cloncurry occurred in brittle-ductile shear zones from geochemically variable and complex, CO2-rich, 300°C to 500°C, high salinity fluids with magmatic stable isotopic signatures. Recently published studies of a giant granitoid-hosted magnetite vein complex at the Lightning Creek prospect (>1000 Mt magnetite) suggest it is a product of internal differentiation and endogenous Fe and Cu-rich hydrous-carbonic fluid phase generation within a quartz monzodiorite-monzogranite intrusion. Coupled with other field relationships, this points to a possible genetic relationship with intermediate (55 to 65 wt% SiO2) members of an alkaline and partly shoshonitic granitoid supersuite which appears to have both mantle and crustal source components from ?Nd evidence. In constrast, main-phase mineralization at Olympic Dam in the Gawler Craton is distinguished by hematite-phyllosilicate alteration and chalcopyrite-bornite-chalcocite zoning, reflecting fluid mixing in a high level (<250°C) system with a probable large component of meteoric water. Early high-temperature parageneses and fluid inclusions imply that the extensive hematitic breccias overprinted an older magnetite system which may have had similarities with those at Lightning Creek and Ernest Henry in the Cloncurry district.Deposits of this family are inherently difficult to find and evaluate as even within a single district, there is no reliable relationship between the location of ore and any specific combination of geophysical characteristics. Diverse alteration assemblages, geochemistry and physical characteristics suggest the deposits reflect the interaction of multi-sourced fluids with different host rocks in a wide range of geological environments. Recent discoveries and research in the Cloncurry district have extended the range of deposit models available and aid the development of a rudimentary classification in which economic and exploration characteristics can be linked to variations in the mechanisms and environments of ore formation."

Jan 1, 2001

By Bruce F. Grant

"INTRODUCTION The future of oil production in the part of the Appalachian region included in southwestern Pennsylvania; West Virginia, and southeastern Ohio is directly dependent on the maintenance of existing wells. This report presents an analytical study of the methods used in oil-well reconditioning in this area. The study is part of a research program designed to evaluate those means of stimulating oil production that can effectively and economically maintain present oil-production rates and make it possible to keep existing wells in operation. Well-reconditioning work was curtailed during the war; therefore, an abnormally large number of wells in the Appalachian Region is now in need of repair. Because the lubricant content of Appalachian crude: oils is high and the refined lubricating oils an; particularly suited to use in high speed, high-temperature engines, the demand for these crude oils during the war exceeds, the maximum rate of production obtainable under wartime operating conditions. Increases in operating, expenses, inability to meet war-time reconditioning costs, and inflexible price structures caused the abandonment of an alarming number of wells during the past 4 or 5 years.As a means of increasing regional oil-production rates, new drilling in the older fields for primary production generally is uneconomical because reservoir pressures in most of the fields have virtually been depleted and the production rates of newly drilled wells are small."

Feb 1, 1948

By William L. Husk

Stockpiles have always been a necessary part of coal mining except, perhaps, when a person was mining only for the needs of his family from a seam on his home place or coal mined for the use of a small hamlet and carried to each man&apos;s house as it was mined. Then it may have been stockpiled at each man&apos;s place for several days or on the village common. Mining with this limited production required waste stockpiling. Stockpiling of the products of coal mining, both coal and waste material, has always been a necessity. Very little coal has ever been moved directly or immediately from the working face to the point of consumption and burned. It has always been expedient to stockpile the coal some- where and store the waste.

Jan 1, 1981

By Getu F. Biftu

There is general agreement among scientists that global surface temperatures have been increasing during the past decades. The increase in temperature is postulated to be the result of either an increase in greenhouse gases emission or climate variability (i.e., due to variations in sun or volcanic activity or El Nino and La Nina events) during past decades and may continue to increase. The effects of a predicted rise in the Earth?s surface temperature include an increase in average global evaporation and increase or decrease in precipitation (Bloomfield, 1992; Mann et al., 1991; Vinnikov et al., 1990; Gan 1995; Zhang et al., 2000a). The general circulation models (GCMs) project a global warming due to greenhouse effects of 1.5-4.5°C by the mid 2050s, with the most pronounced changes taking place in northern latitudes (Nicholls et al., 1996). However, similar predictions at a watershed scale or even a regional scale using GCMs are mot possible yet (Arnell et. al., 1996; Georgievskii et. al., 1996; Zhang et al., 2000a). Detection of historic trends, changes and variability in climatic variables is another indirect means of understanding potential future changes or variability at regional and local scales. The main objective of this paper is to review studies related to climatic change or variability and associated hydrologic changes at a regional scale and local scale, particularly those studies applicable to the Oil Sands Region (OSR) of Alberta. This paper identifies gaps in our current understanding of the hydrologic processes that may be affected by climate change; it discusses potential implications to developments in the OSR; and it explores mitigation opportunities including several that have already been implemented.

May 1, 2004

1. Proposals were submitted to the Western Administrative Center of the US Bureau of Mines, Denver, Colorado on 30th December, 1974 and Contract No J 0255003 was awarded, the effective date being 8th May, 1975. Dames and Moore, Denver, are associated with PD-NCB Consultants in regard to environ-mental problems, surface mining practice and legislation in US. BACKGROUND TO THE STUDY 2. Under the threefold pressures of -increased domestic fossil fuel demand -increased value of domestic energy resources -increased demand for environmental protection and safety

Jan 1, 1976

By C. Babcock

When a flat-lying mineral deposit such as a coal seam is mined, some coal is left to separate the roof and floor so that miners and machines can safely mine the seam. The mineral left is in the form of mine pillars. If too much is taken, support problems and unsafe working conditions result. If too little is taken, the mining operation will be unable to compete economically with other mines. Therefore, one must select pillars of the optimal size to maximize mining recovery and minimize risk to miners and equipment. Later, if the pillar support is no longer needed and the surface can be allowed to subside the thickness of the coal seam, then the pillar support can be removed to increase mining recovery, and initial pillar size is not as critical. Only a small part of the information available on pillar design can be presented here. The purpose of this report is to summarize some of the work done by the U.S. Bureau of Mines and others on pillar design, which is reported in the literature from 1833 to the present, and present rock mechanics test results that aid in understanding mine pillar behavior. The variable names used are those of the authors cited. This results in multiple use of some variable names.

Jan 1, 1994

By R. V. Ramani

This volume is the second of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume I: Ore Reserve Estimation, Volume III: Mine Coordinate Generator System, and Volume IV: User&apos;s Manual for OPMHS/2. The dragline model described in this report simulates the movement of the dragline bucket across the digging face, the swing load, the dump, and swing back. It is programmed to handle chopdown, key cut, main cut, and rehandling operations. Provisions have been made for simulating equipment and mining delays. Any mining method can be specified in terms of numbered blocks, the dragline positions for the mining block and the dumping location for the block. Accounting procedures permit the calculation of production rates, rehandle volume, dig and delay times. The model can be used to study the effects of varying mining conditions, cut width, and spoiling sequence with special reference to toxic spoil, overburden and bench removal procedures. The basic input data for the model include machine parameters, the geology and material characteristics, the mining parameter, and the delay characteristics of the equipment.

Jan 1, 1985

Watershed Jll in Jefferson County, Ohio we instrumented in 1977 as one of three watersheds established for the purpose of investigating surface mining and reclamation effects upon local hydrology, sediment discharge, and sediment and water quality. Each watershed was less than 50-acres in size, and was in a different geologic setting within southeastern Ohio. Surface runoff and ground¬water levels were monitored. Samples were taken for sediment determination and chemical analysis prior to mining. Monitoring and sampling continued through the period of watershed disturbance caused by mining and reclamation activities, which began in May 1980 at Watershed Jll. A psuedo-postreclamation period followed the initial cessation of man-machine activity on the watershed. A second reclamation effort occurred in the fall of 1981 and was to be followed by a third in 1982 after observations ceased. A true final postreclamation period was not monitored at this site, because the erosion control practice (terrace diversions) failed after each reclamation. Watershed Jll was a small pasture and wooded watershed with sandstone and shale above the mined coal seam prior to mining. A clay layer under the coal supported a perched saturated zone, termed the top aquifer for convenience. A lower underclay supported a second saturated zone called the middle aquifer. A lower perched aquifer had been dewatered by previous deep mining. After about three years of premine data and about two and one-half years of mining reclamation and psuedo-postreclamation data, the following general observations may be made: 1. The mining-reclamation phase was very short, and the postmining period was characterized by erosion failures and remedial disturbances that kept the watershed condition and size in a state of change. It was impossible to collect sufficient data to confidently characterize the hydrologic-sediment-chemical aspects of the mining period or of a postreclamation period and, most importantly, of the future watershed after its various properties and characteristics have ceased adjusting to its severe disturbance and reconstitution. 2. A seeding of wheat followed by grasses and legumes was not a particularly successful reclamation practice in terms of stabilizing the new soil. Numerous rills and small gullies developed in spite of installed diversions. 3. Storm runoff rates and yields at the watershed outlet increased from the premine, (phase 1) to the mining-reclamation (Phase 2) periods, and remained at or near the Phase 2 level through the postreclamation (Phase 3a) period. 4. The top aquifer changed in physical and chemical character as a result of mining and was becoming reestablished as the project drew to a close; but it is impossible to predict its final configuration or character. 5. Dewatering of the top aquifer resulted in a complete cessation of baseflow because the middle aquifer water table lay below the elevation of the watershed outlet. 6. The top and middle aquifers were merged in one area of the watershed where the upper coal underclay was disturbed. 7. Failure of the diversion terraces and their outlet obscured the effects of the reclamation practice upon sediment concentration and yields. There was little difference in sediment concentrations between Phases 2 and 3a. 8. Drinking water standards were met by surface waters throughout the period of observation except for two samples that exceeded the nitrate-N allowable level of 10 mg/l. 9. In all Phase 3 surface-water samples, iron concentrations were within the limits established by OSM, and manganese concentrations exceeded the regulation level only once. pH fell below the lower regulation level of 6.0 between 10% and 20% of the time. 10. The chemical quality of sediments was generally about the same after reclamation as before mining, with the exception of organic carbon, which decreased.

Jan 1, 1983

By Ernest W. Hilton

The purpose of this investigation was to assess the environmental impact of the surface mining methods currently used in the steep-sloped areas of Central Appalachia: southern West Virginia, eastern Kentucky, southwestern Virginia and northeastern Tennessee. Comparisons are made between mountaintop/cross ridge mining, contour strip, augering and an innovative method surface shortwall mining which was attempted at Julian, West Virginia. Included in this final report are a discussion and analysis of current Appalachian production, reserves, and the extent of land affected on a county- by-county basis. Additionally, the seams within the steep sloped region have been assessed according to minimal standards of thickness, surrounding lithology, and areal extent to determine their amenability to surface shortwall mining. These seams have been tabulated with their ash, sulfur, and BTU content on a county-by county basis. Only minimal statements are made concerning quantity because of the narrow set of conditions required by the shortwall method. Other sections deal with the possible technical failings of an operational surface shortwall system based on field studies at shortwall operations, discussions with people experienced with shortwalls and research into ground control problems at sites where short- and longwall operations have been monitored. A final section details proposed additional research directions which the Bureau might take in the future.

Jan 1, 1979

This report briefly describes the broad program of research and technologic work conducted by the Bureau of Mines on coal and related subjects during 1966. In addition to n description of investigations on mining, preparation, and utilization of coal, an account is given of the Bureau&apos;s work in mine health and safety, coal resources, mine explosives, and environmental conditions relating to coal mining and utilization. Details of most of the projects are reported in publications cited throughout this report. Centers and laboratories conducting the coal research and related investigations appear in appendix A; organizations, institutions , and companies contributing to the Bureau&apos;s coal research and technologic program are listed in appendix B.

Jan 1, 1967

By James H. Cobbs

The utilization of large diameter drilled holes for mine shafts seems to have had its beginning in Europe about 1850 (28) where the mining industries of Germany and The Netherlands first used drilled shafts. Recent shafts in softer formations of diameters as large as 25 feet and as deep as 1, 700 feet have been drilled in both The Netherlands and Germany. The first shaft drillers utilized cable tool or churn drilling techniques which limit both hole diameters and drilling speeds. Though some churn drilling of shafts is still performed, rotary drilling has been the dominant technique for many years.

Jan 1, 1973

By J. A. Kost

The contract objective was to evaluate the effectiveness of available dust-control technology for double-drum shearers. Eight underground surveys were conducted to evaluate drum design, drum spray nozzle locations, ranging-arm sprays, water quantity, wetting agents, and cutting techniques. The final report is made up of eight dust-control technique reports, each discussing, details of the individual mine surveys.

Jan 1, 1985

By W. N. Patterson

The three major objectives of this contract were (1) to survey underground diesel-powered mining machinery to determine noise exposure problems, (2) to recommend noise control techniques, and (3) to develop a technique for predicting underground sound levels from surface sound power measurements. The objectives were achieved. The contractor developed information on the severity of the noise problem caused by diesel engines underground and pinpointed the equipment causing the problems. He recommended a number of corrective techniques that can provide relief until long-term solutions are found. A procedure for predicting underground noise levels from above-ground measurements of the machine noise was found valid for several cases tested.

Jan 1, 1975

By A. Brown

This report details work performed and results obtained in a study of the water management aspects of oil shale mining and retorting in the Piceance Creek Basin. Three specific sites were investigated, and optimal water management systems for both conventional and in-situ extraction processes were generated. Water-related legal and environmental constraints on development were identified and the water management schemes were developed in compliance with these regulations. Limitations on shale oil production implied by limited water supplies were evaluated. Potential Basin-wide effects of development were evaluated using a computer model, and mitigation strategies were developed. Recommendations for additional investigation and analyses were presented.

Jan 1, 1977

By Charles H. Rich

This Bureau of Mines report is an expansion and update of Information Circular 8719 and comprises maps and tables listing the name, location, and other pertinent data concerning certain fuel-related projects. The maps show the locations of the planned or proposed facilities. The tables include information on projects involving the proposed or planned development of fuel resources, as well as the development of storage, transportation, and conversion facilities. The report covers the 24 States west of the Mississippi River including Alaska and Hawaii. Of the 808 projects for which information is provided, 219 concern coal mines, 246 concern electric generating plants, and 115 concern uranium mines; Energy Supply and Environmental Coordination Act coal conversion notices are also included. Because of the dynamic nature of the energy industry, many uncertainties exist and some of the listed projects may never become realities. Also, no attempt has been made to determine the degree of certainty or viability of each project.

Jan 1, 1978