Search Documents

By L. Yuan, J. H. Rowland III

"In 1995 and 2003, the Mine Safety Health Administration (MSHA) conducted surveys to determine the number of atmospheric monitoring systems (AMS) being used in underground coal mines in the United States. The survey reports showed data for the different AMS manufacturers, the different types of equipment monitored, and the different type of gas sensors and their locations. Since the last survey in 2003, MSHA has changed the regulation requirements for early fire detection along the belt haulage entries. As of December 31, 2009, point-type heat sensors were prohibited for use for an early fire detection system; instead carbon monoxide (CO) sensors are now required. This report will examine the number of AMS currently used in underground mines in the United States to see if there is a change in their use. The locations and parameters monitored by AMS are also discussed. INTRODUCTION The last survey conducted by the Mine Safety and Health Administration (MSHA) on atmospheric monitoring systems (AMS) used in underground coal mines in the United States (US) was in 2003 [1]. The survey report states that since 1995 there had been a steady increase in the use of AMS in underground coal mines as the technology of CO sensors was improved by manufacturers. AMS had become more reliable and some CO sensors could be purchased with the capability to discriminate between the CO produced from a fire versus CO produced from diesel equipment. This increase in reliability had reduced the number of false alarms and the response time. The faster response time to a developing fire allowed for the miners to take the necessary action to put out the fire or exit the mine. It should also be noted that at the time of last MSHA survey, some mines still used point-type heat sensors to detect the presence of a fire on conveyor belts. This detection method works by measuring the temperature of the air around the sensor. As a fire starts to develop, smoke and hot gases are produced from the combustion process, and the air is heated up. Once the air and gases reach a designated temperature detected by the point-type heat sensor, a fire alarm signal is generated. Studies have shown that the response times for detecting the presence of a fire using CO sensors are much shorter than using point-type heat sensors [2]. Finally, since the last MSHA survey, regulations have changed on the type of automatic fire detection systems permitted to be used in conveyor belt entries. As of December 31, 2009, point-type heat sensors are not permitted to be used for fire detection in underground coal mines in the US; instead CO sensors are required as a replacement (30 CFR 75.1103-4). This study will examine how the changing of the above regulations has impacted the use of CO sensors in underground coal mines in the US compared to their use based on the last MSHA survey. Importantly, in the previous MSHA survey, the data was recorded for producing and non-producing coal mines. In this study, only the data from the producing coal mines was recorded. Data was collected from a total of 235 coal mines for this study with the help of the MSHA district offices."

Jan 1, 2017

By J. -E. Eriksson, L. Hupa, T. Khazraie

With increased co-firing of coal and different biomasses in power plants, there is a growing need to study and characterize the produced, often heterogeneous ashes and to assess their utilization as secondary raw materials. In this work, we compare different methods for characterizing the ash compositions. These methods include scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDS), X-ray fluorescence (XRF) and inductively coupled plasma emission spectroscopy (ICP-OES). The content of carbonaceous residues in the ashes was measured with CHN Sanalyzer. The methods and the pretreatment required for each of the analysis were studied in detail for three ashes: (1) coal, (2) peat and wood, (3) peat and wood residue with dolomite addition. The limitations of each method will be discussed. This work gives guidelines for selecting a rapid and reliable method for analyzing the suitability of the ash for a particular application.

Mar 1, 2018

By D Cliff

Despite advances in technology, the Australian underground coal mining industry continues to have incidents involving spontaneous combustion. Managing these incidents relies heavily on understanding the state of the event as it develops and controls are applied. Gas analysis plays a major role in aiding this interpretation. This interpretation is based upon laboratory testing of coal samples under conditions very different to those found in an underground coal mine. This paper will explore the links between laboratory data and actual events. It will highlight the difficulties of using laboratory data. It will outline the relevance of laboratory data and how it can be usefully applied to manage spontaneous combustion events as well as in establishing relevant trigger action response plans to facilitate early detection and control of such events. The paper will identify some of the factors that need to be applied when adapting laboratory data to apply to the underground coal mine. It will outline the need for comprehensive knowledge of the local conditions and gas concentrations to be expected at all locations in an underground coal mine. Further, it will demonstrate the need for mine environment monitoring to go beyond simply measuring gas concentrations but also to include reliable atmospheric pressure, temperature and air velocity monitoring.CITATION:Cliff, D, 2013. Gas analysis - Linking the laboratory with reality, in Proceedings The Australian Mine Ventilation Conference , pp 277-282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By W. J. Wiehagen

The Work Crew Performance Model (WCPM) seeks to define performance variability within similar tasks of an underground work crew and relate observed variability to a cost consequence. Performance variability is described using work site observations to determine the adherence to job elements con¬tained within a standard operating procedure. Key components of the WCPM include (1) job definition through task analyses and the ranking of job elements by perceived cost consequence, (2) observational techniques for establishing performance baselines by measuring adherence to safe and proficient job procedures, and (3) cost linkages between adherence to task procedures and measures of consequence for noncompliance. Data presented within this report were obtained through the study of shuttle car operation in an underground mine in Appalachia. Observed adherence to safe and proficient job procedures by opera¬tors matched well with the consensus profiles (measured through a nominal group technique) with min¬ing personnel. It was also found that experienced operators consistently outperformed less experienced, incidental operators. These findings imply potential use of the WCPM as a practical procedure for thinking systematically about the choices available to reduce performance variability. Field application of the model can offer useful data to evaluate training and financially support performance improvement strategies that can be tested for their ability to reduce human error.

Jan 1, 1994

By L. Yuan, J. H. Rowland

"In 1995 and 2003, the U.S. Mine Safety and Health Administration (MSHA) conducted surveys to determine the number of atmospheric monitoring systems (AMS) that were being used in underground coal mines in the United States. The survey reports gave data for the different AMS manufacturers, the different types of equipment monitored, and the different types of gas sensors and their locations. Since the last survey in 2003, MSHA has changed the regulation requirements for early fire detection along belt haulage entries. As of Dec. 31, 2009, point-type heat sensors are prohibited for use for an early fire detection system. Instead, carbon monoxide (CO) sensors are now required. This report presents results from a new survey and examines how the regulation changes have had an impact on the use of CO sensors in underground coal mines in the United States. The locations and parameters monitored by AMS and CO systems are also discussed.IntroductionThe last survey conducted by the U.S. Mine Safety and Health Administration (MSHA) on atmospheric monitoring systems used in underground coal mines in the United States was in 2003 (Francart, 2005). A total of 146 active mines were surveyed. The survey report states that since 1995 there had been a steady increase in the use of atmospheric monitoring systems in underground coal mines as the technology of carbon monoxide (CO) sensors was improved by manufacturers. Atmospheric monitoring systems had become more reliable, and some CO sensors could be purchased with the capability to discriminate between the CO produced by a fire versus CO produced by diesel equipment. This increase in reliability had reduced the number of false alarms and the response time. The faster response time to a developing fire allowed miners to take the necessary action to put out the fire or exit the mine.At the time of the last MSHA survey, some mines still used point-type heat sensors to detect the presence of a fire on conveyor belts. This detection method works by measuring the temperature of the air around the sensor. As a fire starts to develop, smoke and hot gases are produced from the combustion process, and the air is heated up. Once the air and gases reach a designated temperature detected by the point-type heat sensor, a fire alarm signal is generated. Studies have shown that the response times for detecting the presence of a fire using CO sensors are much shorter than when using point-type heat sensors (Conti and Litton, 1995)."

Jan 2, 2018

By Heman Manchanda, Jyoti Agarwal

Several infrastructure projects are under construction in India; many of them involves construction of deep foundations like reinforced concrete and steel piles to support super structures. As most of the piles being constructed in India are reinforced concrete bored piles, there are always uncertainties relating to the quality of construction, and in this case non-destructive methods to ascertain quality of piles becomes very crucial to success of any project. Non-destructive pile testing is becoming more and more popular with growing technologies wherein geophysical techniques and wave propagation theories are being used for pile quality and length analysis. Low-strain pulse echo method and cross-hole sonic logging testing are two pile integrity testing techniques being currently practiced in India which are cost effective and provides reliable near accurate results if analyzed properly. Paper presents current practices being adopted in India for conducting these two tests, highlighting the critical site considerations and analysis techniques. The paper also discusses various execution and interpretation challenges faced by practicing engineers and recommends a way forward.

Sep 1, 2022

By Tyler Rockley, Carla Reyes

Autonomous fragmentation measurement systems designed for shovels have been in operation for nearly two decades, however fragmentation systems capable of performing in the dynamic conditions of the front-end loaders (FEL) were only recently introduced to the market. This paper presents an in-depth evaluation of an automated digital fragmentation measurement system specifically designed to perform under the dynamic operational conditions of the FEL in two of Teck’s mine sites. As early adopters of this novel application, Teck embarked on a Proof-of-Concept (PoC) trial phase, defining a set of key performance indicators (KPIs) to qualify the performance of the digital solution in tough mining operating environments. The KPIs focused primarily on the hardware robustness, quality of image and segmentation, both day and night, availability of the system and sample ratio. The benefits expected from using this technology include increasing the safety of the current fragmentation measurement process, improving the quality of the analysis, increasing the sample representativeness, and using the attributes of the system to create an oversize detection alert to inform the loading operation process. A critical part of the evaluation was verifying the system’s effectiveness on the particle segmentation algorithm as this element often gets overlooked, especially when dealing with the large number of samples autonomous systems can generate; minor misclassifications due to inadequate segmentation are often dismissed as they might not be statistically significant, however systematic misclassifications can cause unacceptable deviation in the data and limit the intended application of the technology. The system’s performance was further validated through several tests that involved identifying objects of known sizes to ensure the reliability on the consistency of the particles’ segmentation.

Jan 21, 2025

By K. Neumann

"INTRODUCTION For many automation and safety tasks in open cut and underground scenarios it is crucial to have highly reliable distance measurements at hand. These measurements can for instance be used to obtain the exact position of a machine in one-, two- or even three dimensions. Research and development has shown interest in the ultra-wide-band technology (UWB) in recent years. While for this technology short range, high speed data transfer is the current main research focus, the technology can also be used for highly accurate ranging applications. Due to the use of a very wide frequency band, it is robust against disturbances of many types (e.g. EMC, rain, dust etc.) and is therefore attractive for the use in mining applications. The wide frequency band also offers benefits for ranging applications. Especially in environments with strong multipath problems such as in underground mines it is possible to focus on the dominant signal propagation path, thus increasing the reliability of the measurements. [1] State-of-the-art UWB ranging equipment claims precision within the range of a couple of centimeters and working ranges of more than hundred meters. At the Institute for Mining and Metallurgical Machinery (IMR) at RWTH Aachen University in Germany a modern UWB system was examined in several laboratory and real life tests to examine the feasibility of UWB bases ranging equipment in mining applications. UWB TECHNOLOGY The term ultra-wide-band denotes radio systems that use an ultra-wide frequency band. A common definition for UWB radio systems is that it needs to work on a frequency bandwidth of more than 500 MHz or a bandwidth equal to 20% or more of the center frequency [1]. Due to the ultra-wide frequency bandwidth UWB systems overlap the frequency spectrum of narrow band radio technologies like Wi-Fi, Bluetooth and other mobile communication systems which use a defined carrier frequency onto which information is modulated on (e.g. by using frequency or phase modulation). In order to not conflict with these other radio applications, it needs to be ascertained that the transmission power of a UWB system on a given frequency is so low that narrow band systems are not affected by it. As opposed to this only a small fraction of the UWB system’s bandwidth is affected by the narrow band system. The unaffected remaining bandwidth is sufficient to reconstruct the original signal, even if additional noise is present. Figure 1 shows the power spectral densities of popular radio standards [6], [7], [8]. A significant driver of research and development of UWB systems has been wireless high bandwidth communication. Using an ultra-wide frequency band is highly desirable here, as the channel capacity is dependent on the bandwidth. So far systems have been realized especially for short distances (e.g. wireless USB or Wireless HDMI) but beyond that, communication systems for long distances (several kilometers) are possible [2]. Advances in semiconductor technology led to a reduction in power dissipation of such systems. This enabled higher integration levels which in turn facilitated smaller solution sizes for space constrained applications [3]. Nowadays, UWB is also used for high-precision ranging applications [4], [5]."

Jan 1, 2015

By Curtis G. Kremer

"New explosives initiation systems continue to be developed as new technologies make advancements possible. Due to recent initiator developments, explosives users now have the most reliable, accurate, safest and easy to use systems ever offered. Three initiation systems recentlyintroduced which offer significant improvement over standard electric and nonelectric initiation systems include Magnadet, EXEL high-strength shock tube, and Redundant two-Dath surface delay systems. These three systems will be discussed zn cecail with rmpiasis on their functioning, safety characteristics, ani specific application areas."

Jan 1, 1991

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan

In the bench blasting, the realisation of an economic, and safe blasting is only possible with a reliable blasting design on condition that considering all sequential activities such as drillingblasting, excavation-loading, haulage, crushing (especially primer crushing). Here what we mean with a good, and reliable design is that ensures an almost displaced, adequately swelled muckpile with desired fragmentation degree for the loaders effectivity, and succesive usage. Meanwhile it must also has no environmental problems such as ground vibration, air blast, and rock flyings, or at least these matters have to be minimised. Two main parameters which have generally being questioned to achieve a safe and economic design on any rock conditions, are specific charge, and burden. In the condition of determining these elements, the other blasting parameters could be calculated according to them, and the blasting design could be completed. Within the scope of this study, it was aimed to determine the optimal blasting conditions of gypsum which is major rock unit of overburden at Sivas Celestine open pit mine. First of all, the engineering (mass, and material) and digging difficulty classifications of gypsum were done according to the current classification systems by using the results of field and laboratory studies. Then the blasting system which was being used on all rock units, was considered, and the necessary data were obtained. After previewing the site properties, predesigns were done, and applied by adopting Langefors design model. The necessary adjustments were done before, during, and after the shots, and the applications were observed. In order to determine, and record the data from each shots properly, a practical form was developed, and all data were transfered to these forms which give information about the blasting results such as muckpile displacement, and height, average particle size, back break, and rock fly existence, number of boulders etc. The blasting parameters such as burden, hole diameter, hole inclination, the amount and position of primers, bench height, delay sequence, and blasting geometry were considered for the iteration of each shots. During the applications, ANFO, gelatine dynamite, and electric delay detonators were used as explosives.

Jan 1, 2004

By R Williams, M Baxter, D Zink, R Cunningham

The purpose of this paper is to discuss the efficient operation of a tailings dewatering circuit comprising a thickener and filter press through proper control and automation. It is common to see thickeners and filter press circuits each with their own control systems. This can cause multiple issues when trying to increase efficiency and reliability of the tailings management process. By automating the thickener and filter press controls, you are eliminating any delays and inconsistencies caused by human error and process variations. When done properly the system can maintain a consistent product as the feed characteristics change. Previously, operators would have to monitor the process parameters and adjust the system accordingly. This can now be accomplished using state of the art process control equipment that continuously monitors and adjusts critical variables using Programmable Logic Controllers (PLC) and Proportional Integral Derivative (PID) loops. The paper will detail the control theory used to maintain these systems, highlight other benefits of having a fully integrated plant such as predictive maintenance and remote diagnostics as well as present examples of how these have been implemented in field examples.CITATION:Baxter, M, Cunningham, R, Williams, R and Zink, D, 2018. Tailings process optimisation through automation and controls integration, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 416–421 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By V. H. Valenzuela

Materials in process or in stocks are quite relevant items in almost every plant, particularly in mining operations, where efficiency in rate of recovering material of interest becomes a key issue when production costs are evaluated. A manager requires information to do an effective use of the resources, especially when raw materials are involved. Losses associated to leaking, efficiency in the transformation process, performance of equipment, and operating conditions are a short list of items which must be properly identified and evaluated. Operations supervisors require information in order to keep key process variables under control. Because of these information needs, it is absolutely necessary to carry on a series of activities related with installation and maintenance of measuring equipment, sampling equipment, sample preparation, chemical analysis, statistical analysis, data handling and reports generation. These pieces of data must be managed on a wise manner in order to get the most of it, keeping always on mind data reliability. Normally, information related with metallurgical balance and even more, the metallurgical balance concept, is handled under an accounting criteria which does not allow dealing with the real world. This situation happens because the criteria utilized do not consider aspects such as bias and uncertainty associated with every measurement that affect the quality of the information and therefore conclusions drawn from it. The purpose of this paper is to give a few rules, necessary to follow, in order to develop an adequate Metallurgical Balance System for an operational point of view. The Gaussian approach for error propagation is used as a basis, allowing one to know the actual uncertainty of the balance and the way how it can be improved. A few real applications of this concept are listed, detailing experiences obtained from practice.

Jan 1, 2007

By William C. Spindler

Five industrial installations of large lead-acid battery energy storage systems in operation in the United States, West Germany and the 'Republic of South Africa will be described. One example is for a deep mine shaft in which air ventilation and personnel evacuation require the highest reliability for emergency power. The battery system is designed for additional cost-effective benefits of peak load lopping and reactive power control. Commercially available lead-acid batteries of the following types are in use1 traction, truck, submarine, high power, and gel. Electrode grids of both the calcium and antimony alloy types are used. Applications include deep and shallow cycling as well as float and intermittent use. The advantages of sealed lead-acid batteries in UPS (uninterruptible power source) systems are well established throughout the world, and such system suppliers could readily develop markets for industrial emergency and peak power lead-acid storage battery installations.

Jan 1, 1990

The importance of proper planning, preparation, and execution of a steady state sampling campaign for metallurgical plant assessment must not be underestimated. Careful planning can increase the amount and reliability of information from an optimum number of samples and fully utilize available plant data. It requires specification of the data required, determination of run duration sampling frequency, the selection, modification and testing of sample points and cutters, as well as organisation and briefing of plant and sampling personnel. Preparation immediately prior to sampling, the conduct of the sampling campaign itself and procedures to handle the collected samples and information are discussed. Cutter design, fabrication and use are described in detail, and typical sampling situations, for ball mills, classifiers, pipes, launders, flotation cells and thickeners are considered individually. Measurement of pulp flow rate can often resolve difficult mass balance problems, and discussion of convenient techniques is included.

Jan 1, 1976

By Shelby Z. Palya

"INTRODUCTION The Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mining substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January 1, 1975, to December 31, 1979. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960; 2 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960; 3 the 5-year lists of publicatioll3 and articles, from January 1, 1960, to December 31, 1964,4 from January 1, 1965, to December 31, 1969,5 and from January 1, 1970, to December 31, 1974; 6 and the annual lists of Bureau publications and articles from January 1 to December 31, 1975,7 from January 1 to December 31, 1976,8 from January 1 to December 31, 1977,9 and from January 1 to December 31, 1978.10"

Jan 1, 1980

By K. Zipf, Z. T. Bieniawski

"An extensive mixed-mode fracture toughness testing programme was conducted on coal from three coal fields. A special mixed-mode testing fixture for coal and other geologic materials was developed together with reliable specimen preparation procedures. Dynamic modulus measurements made on each of the 116 fracture toughness specimens showed that these coals exhibit certain degrees of anisotropy. The fracture toughness testing programme systematically varied the loading rate, specimen orientation and fracture loading mode. Loading rate did not significantly effect the fracture toughness over the quasi-static range tested. Orientation did have a significant effect on measured fracture toughness. In the coals tested, the divider orientation and arrester orientation had higher fracture toughness than the short transverse orientation. Data showed that one orientation could have almost twice the fracture toughness as another. The fracture toughness testing enabled certain evaluations of three mixed-mode fracture theories: maximum tangential stress, maximum energy release rate and strain energy density theory. Due to the extreme heterogeneity of the coals tested, definitive conclusions regarding the best mixed-mode fracture theory are not possible; however, data do tend to support the strain energy density theory. INTRODUCTIONThe major aim of this research is to ·develop a fundamental understanding of how fine· fragments of coal (respirable dust) are generated during a fracture process. In a related paper [l], a hypothesis was presented for the mechanism of fine fragment formation during a generic coal material/cutting tool interaction. In this hypothesis, fine fragments are created during coal material/cutting tool interactions that are best described as general mixed-mode fracture processes. Data are required on the mixed-mode fracture behaviour of coal, the physical character of the newly-created fracture surfaces and the character of the inherent flaw structure of the coal material. Accordingly, a test programme was designed that provided some information in each of these areas. The testing effort seeks to measure critical fracture toughness under mixed-mode loadings as a material parameter characterizing in part the tendency of various coals to generate undesirable quantities of fines and respirable dust."

Jan 1, 1990

By Frenk van den Berg

In the manufacturing of steel strip for the automotive sector, the mechanical properties are largely defined by the process conditions in the hot strip mill. In particular the phase transformation, from austenite to ferrite, which takes place during the forced cooling stages on the run out table (ROT) after the finishing mill, governs the microstructure and hence the mechanical properties.In current practice, metallurgical models are used to predict the phase state at each position in the strip. These model predictions are supported by pyrometer measurements along the ROT. Although reliable in the majority of the situations, both measurements and models sometimes have difficulties in providing robust output. In this paper, we present a new type of inline measurement, which directly measures the amount of phase transformed. The instrument is based on a technique known as impedance spectroscopy. As result of a collaboration of different institutes and companies, the equipment is robustly running during several years exclusively in the Hot Strip Mill of Tata Steel in IJmuiden.

Aug 16, 2017

By Kyle T. Chomyn

Multi-disciplinary engineering analysis and advanced modeling techniques were used to identify and develop low cost design modifications to improve a blast furnace hot blast air distribution main that experienced frequent refractory failures. Piping flexibility analysis helped identify the root causes of refractory damage and determine the need for new expansion joints. Finite element analysis was used to optimize a custom-designed elbow-to-elbow tie-rod system, which ensures thermal expansion loads are not placed on connecting piping. Heat transfer coefficients through the elbows were estimated using computational fluid dynamics (CFD) flow modeling. The cast refractory design was changed to a more reliable brick refractory design. Excessive draft was occurring during furnace back-drafting, so the system was assessed using CFD, and a passive flow-reduction spool was designed. This firstprinciples engineering design approach allowed for optimization and verification, ensuring that the new design addressed the root cause of the previous deficiencies.

Aug 17, 2017

By Per Hedvall, Jan-Eric Ståhl

"The main objective of this study is to introduce the new Sandvik’s production cost-model within Crushing & Screening (C&S) technology. So far, there have been different ways of determining different production costs in the industry, however, the previously published and presented methods have not been very efficient in calculating the costs per product and metric ton. Accordingly, the current study has been planned and started in collaboration with Lund University to provide an accurate and easy to implement cost estimation program to determine the costs for crushing and screening plants worldwide.The proposed model has been adapted to fit the C&S processes of different rocks/ores fractions. The result is presented as cost per ton of the end product(s).Within this paper the cost estimation results for 3 different crushing and screening plants are presented based on the information obtained from the following sources: a) documents at Sandvik SRP, b) Sandvik’s crushing & screening internal/external machines/plants data and information, c) literature studies, including the use of Sandvik’s internal/external simulation and software programs, d), visiting the crushing and screening plants ,e) interviews, information systems’ data, and, f) testing and observations by ourselves.In order to improve the level of accuracy and the validity of the attained results, simplistic Monte-Carlo simulations have been used, where needed. The achieved results, so far, have proven the reliability of the model. The calculated cost estimations have shown an accuracy over 80% when they compared with real cost data obtained from plant practices.The current cost calculation model, will offer the possibility of:•,Calculating the production costs in proposed and/or existing C&S plant.•,Making detailed cost analyses for the end product(s) in proposed and/or existing C&S plants.•,Determining the profitability of each finished product when it’s required.•,Cost optimization by potentially cutting the cost for part of C&S plant with an existing plant practice"

Jan 1, 2016

By G. R. Doubek

Dual Tube Reverse Circulation (DTRC) drilling has been extensively used for collecting groundwater information for the dewatering program at Amax Gold Inc. Sleeper Mine. This paper presents a discuss ion of the types of data which can be collected from DTRC drilling, as well as the effect submergence has on the data. A simple low-cost method of injection testing has been developed using DTRC equipment, allowing quantitative data to be obtained from exploration or test holes. Potential yields can be determined for each drill location, allowing siting and design of production wells to be optimized.

Jan 1, 1992