Search Documents

Direct reduced iron (DRI), produced by the reaction between iron ore and reducing gasses, is used as a source of low-residual iron, in addition to ferrous scrap and pig iron, in the production of steel mainly through the electric arc furnace (EAF) route of steelmaking. The main DRI technologies in use are those of Midrex and Hyl, but in recent years a myriad of newer processes emerged based on variations in feedstock, reducing agent and fuel sources. Since the beginning of the nineties, DRI has increasingly emerged as a cheaper, low-residual iron feedstock for EAFs, which have traditionally relied almost entirely on ferrous scrap feed. The main stimulus behind the interest in DRI has been the increasing popularity of the EAF and the ?mini-mill? set-up as the favoured steelmaking option compared to the traditional and much less flexible blast furnace/ basic oxygen converter. This, however, has been creating a problem with regard to availability of low-residual scrap, resulting in upward pressure on high quality scrap prices and leaving DRI, traditionally the ?expensive alternative?, as a much more competitive consideration. The second main determinant has been the increasing production efficiency of existing steel plants which, in the light of improvements such as continuous casting and near net shape casting, has been constraining the supply of low-residual domestic scrap, traditionally the prime source of EAF feed. The explosion of current and proposed DRI projects has been accentuating the mounting interest of global role-players in assuring the availability of reliable sources of low-residual iron units for the future, especially in cases where definitive competitive advantages exist with regard to proximity to primary sources of iron ore and fuel (gas or coal).

Jan 1, 1999

By S. S. Peng, V. Z. Sun

One of the major concerns of ground control in a coal mine is the prevention of roof, pillar and floor failures of the mine entry. To better design and evaluate the stability of a mine entry within a certain level of confidence, a reliability approach is introduced. The advantage of using the reliability approach, rather than the conventional safety-factor (SF) method, is that it not only takes variability of both rock/coal properties and stress into consideration but also assesses the stability of each component and the mine entry as a whole. Therefore, it is anticipated that by using this approach the current ground-control technology in a coal mine will convey a better sense of confidence. The results of a case study show that there is a significant difference in mine entry stability between the current design method and the reliability approach.

Jan 1, 1999

By Ilija Ilic

Recovery of tin from tinplate and production of good-quality detinned-plate for further processing in ironworks has been the subject of interest for many years. Tinplates are mostly used for production of tin containers for food industry and consumer goods. The research carried out so far included determination of the parameters of dissolution of tin from tinplates by alkaline solution of NaOH and electrochemical recovery of tin from the alkaline solutions. During leaching, NaNO3 and methanitrobenzoic acid (MNBA) as oxidants were studied. By leaching the waste tinplate which contains 0.31 % of tin with a solution of 1.12 mol/dm3 NaOH, 0.26 mol/dm3 Na2CO3 and 0.09 mol/dm3 MNBA at temperature of 70°C for 60 mm, a degree of tin leaching of 97 % was attained. MNBA facilitates oxidation of Sn2+ into Sn4+ suitable for obtaining compact, and not spongy, Sn cathode deposit, as it was the ease earlier. Recovery of tin by electrolysis from solutions obtained by leaching was studied to determine the effect of electrolyte composition on the quality of cathode deposit and the degree of electric current efficiency. Experimental results obtained at a laboratory level were checked on an enlarged laboratory set up where continuos leaching of tin from waste tinplate and its electrolytic recovery from the solution obtained were carried out. The experimental set-up -operated under semi-industrial conditions, and about 500 kg of waste tinplate was processed yielding about 1.160 kg of tin (99 % Sn).

Jan 1, 2000

By Nadia C. Miller

In situ metals research to characterize the hydrology of a fractured crystalline rock mass in under-ground mine stopes is discussed. The objective of this study was to find the potential direction, velocity, and concentrations of a lixiviant plume, should leaching solvents (lixiviants) escape from a test stope. The study was conducted by the U.S. Bureau of Mines at the Colorado School of Mines Experimental Mine in Idaho Springs, CO. Since this was a method evaluation site, the lixiviant was simulated using water and acceptable tracers. The site is located in moderately fractured Precambrian migmatite-biotite gneisses of the Idaho Springs Formation. The data required for the characterization were obtained from geologic maps and reports, core logs, and air and water permeability tests. The acquired data were analyzed and applied to a computer model that calculated' the characteristics of a lixiviant plume originating at the stope. A sensitivity analysis showed that dispersivity, ground water velocity, fracture porosity, and fracture spacing had notable effects on the concentration of the plume. Assuming a saturated rock mass, the lixiviant plume would disperse to undetectable levels in a very short time because of a high fracture density at the mine site.

Jan 1, 2010

By Mark Colwell

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a longwall installation roadway (faceroad) design methodology that could be utilized by suitably qualified colliery personnel. This goal was achieved in 2012 and the design methodology (and software package) is referred to as Analysis and Design of Faceroad Roof Support (ADFRS). The intended benefits to underground operations, in the provision of this information and resource, are a safer and more productive workplace.

By J. Patrick Ryan, Thor H. Kiilsgaard, Charles W. Merrill, E. T. McKnight

The U.S. Treasury stocks of silver have been reduced at such a rapid rate to meet industrial and coinage requirements that they face exhaustion in 3 or 4 years. Alleviation of the silver problem will require increasing supply or reduc ing demand. This paper examines poss ible long-range resource development and research programs and improved secondary recovery. The possible reduction or elimination of silver in coinage and development and introduction of substitutes in the arts and industry are also discussed.

Feb 1, 1965

By Sunil Arora, Lisheng Shao, Chris Conkle

"The East Garden Grove - Wintersburg Channel located in Orange County, California, required upgrades along the levees to mitigate potential liquefaction and lateral spreading hazards. The Orange County Public Works designed soilcrete columns constructed between two rows of steel sheet piles along both sides of the channel between Graham Street and Warner Avenue (approximately 2,500 ft), and along an approximately 2,000-ft-long stretch of the south levee. The earthen embankment, approximately 13- to 15-ft high and damaged significantly by erosion, was then excavated to widen the channel to increase the channel flood conveyance capacity.The site is located within the Los Angeles Basin, underlain by several thousand ft of marine sedimentary strata. Uncontrolled fill materials were encountered to approximately 10 ft below ground surface, underlain by tidal and flood plain deposits. Groundwater was encountered at sea level, which is approximately 10 ft below grade.This paper will discuss site soil conditions, and the construction and quality control of soilcrete columns constructed by wet soil mixing; also, the paper will introduce the Drilling Index (DI) as a measurement tool, similar to the cone penetration test (CPT), to evaluate the soil strength in more detail. Finally, the statistical analysis of soil mixing strength distributions for the project quality control will be presented.INTRODUCTIONWintersburg Channel in Orange County, California, required ground improvements along the existing levees to mitigate potential liquefaction and lateral spreading under the site design earthquake. Orange County Public Works designed and developed a cellular pattern of soilcrete columns sandwiched between two rows of steel sheet piles along both sides of the channel between Graham Street and Warner Avenue, and adjacent an approximately 2,000-ft-long stretch of the south levee (Fig. 1). An earthen embankment approximately 13 to 15 ft high, damaged significantly by erosion, was then excavated to widen the channel and increase the channel flood conveyance capacity.Stiff, soilcrete cellular wall structures can reduce the earthquake-induced cyclic shear stress ratio (CSR) in the soil within the cells, thus preventing excess pore water pressure build up which may trigger soil liquefaction. For this project, approximately 6,700 soilcrete columns were constructed in a cellular pattern to an approximate depth of 40 ft. All of the soilcrete columns are 3 ft in diameter with the design unconfined compressive strength (UCS) of 150 psi."

Jan 1, 2015

By E. Quaquero

This article reports on the current state of an ongoing research project which is aimed at implementing intelligent models for hardly predictable hazard scenarios identification in construction sites. As past evidences showed that no programmatic action can deal with the unpredictable nature of many risk dynamics, we tried to survey on how the current approach for safety management in the construction industry could be improved. In our previous research the use of Bayesian networks elicited from subjective knowledge were preliminarily tested. Those networks might be meant as a reliable knowledge map about accident dynamics and they showed that a relevant ratio of occurrences fall in ?hardly predictable hazards? class, which cannot be warded off by programmatic safety measures. This paper reports the second outcome of our research project, which focused on the development of first elementary fragments, regarding the occurrence of a possible ?hardly predictable scenario?. Instead of experts? contributions (who, over their carrier, seldom incurred in accidents), we used ?legal cases? as an accurate source of information. They suggested which categories of ?hidden hazard scenarios? are more likely to happen. We found that the most frequent hidden hazard scenarios are linked to operator?s negligence and abnormal behavior, e.g. irregular removal of scaffolding?s components, unprotected openings, improper use of PPE, etc. Every pattern determined by legal cases has been formalized by a fragment (i.e. elementary network) of the overall Bayesian network. Finally, all the elementary networks were integrated into a comprehensive intelligent tool for realtime hardly predictable hazards prevention. The final setup, asked for interfacing these intelligent models to a low-level sensor network and used to feed them with inputs about the current state of the context, is discussed too.

Aug 1, 2013

By Jin-Wei Huang, Bradley J. Fleming, Sri Sritharan

"Although soil improvement and its application to deep foundations is gaining popularity in the engineering community, this technique is not widely used in high seismic regions due to lack of fundamental understanding of both the behavior of improved soils under high-strain cyclic loading and the interactions between the pile, improved soil, and unimproved soil. This paper describes part of an ongoing Network for Earthquake Engineering Simulation (NEES) project, where two identical full-scale steel pipe piles were driven at a soft clay site in Oklahoma. The soil surrounding one of these piles was improved using the cement deep soil mixing technique in order to enhance its lateral load behavior. Both piles were tested for seismic resistance using dynamic and quasi-static loading.The pile in unimproved soil provided larger displacements with limited lateral force resistance. This pile was subjected to lateral displacements of up to 400 mm, but experienced minimum inelastic actions. On the other hand, the pile in improved soil reached its lateral capacity at a displacement of 100 mm, at which point the critical region at the base of the pile just above the improved ground experienced buckling and fractured due to low cycle fatigue. Compared to the pile in unimproved soil, the improved ground increased the system strength by 42%. Although the soil was improved over 2900 mm, the effective improvement depth was approximately 1300 mm below the ground surface.In this paper, it is demonstrated that the effects of block type soil improvement of limited horizontal and vertical dimensions can be described using a simplified theoretical approach involving a modification to the well-known p-y representation of soil response. An example using this method is presented and shown to give adequate support to a standard 12-inch diameter steel pipe pile embedded in soft soil,IntroductionPilings are the preferred foundation support for many civil engineering structures including highway bridges, railroad bridges, and port wharves. These structures and their foundations are subjected to forces created by earthquakes, wind, waves, water current, vessel impact, ice, and gravity. All loads applied to the superstructure must be transmitted to the foundation where they are resisted by the surrounding soil. With significant lateral loads, use of pile foundations may be the only solution to transmit large structural loads to competent soils. Piles supported by competent soils are relatively easy to design and costs are often attainable. However, thick layers of weak soils such as soft clays are widespread in high seismic areas (e.g., San Francisco, southern Nevada, Washington, Eastern Missouri, and Arkansas), exacerbating design challenges. Soft clays reduce the lateral resistance of the pile-soil system, making the pile foundation less cost effective. In this case, the current design practice is to use an increased number of larger diameter piles, which is a costly alternative (see SDC, Caltrans 2010). An innovative and more cost-efficient solution to this problem is to improve the soil within a short depth surrounding the foundation, thereby increasing its lateral stiffness. Some well-known methods for improving soil include deep soil mixing, stone columns, and simple soft soil replacement with select granular material."

Jan 1, 2017

By J. P. Hugo

Nuclear energy - its interactions with mining and metallurgy - PRESIDENTIAL ADDRESS given by J. P. Hugo Pr. Eng., B.Sc (Eng.) (Rand), Ph.D. (Sheffield) Energy is the life blood of the modern technological era in which we live and it was, I think, Benjamin Franklin who said that the manipulation of energy was the basis of all science and technology. This is perhaps an oversimplification, but there can be little doubt that our life today, and the improved standard of living we aspire to, are governed almost entirely by our ability to generate and manipulate energy. This ability has made it possible for Man - each specimen a feeble twentieth of a horsepower - to travel to the moon, to recover valuable minerals from the depths of the earth, to do arithmetic at unbelievable speed, to lessen the drudgery of manual labour. For these and virtually every aspect of our life we are dependent on energy from external sources. It is, therefore, not surprising that the per capita consumption of energy, and more particularly electricity, has become one of the most reliable criteria by which to measure the standard of living and technological advancement of a country.

By J. B. Gayle

A 1/2-ton experimental coke oven was installed ac the Bureau of Mines Southern Experiment Station, Tuscaloosa, Ala., in 1948. Designated as the Tuscaloosa oven, this unit features a 17-inch carbonizing chamber, globar heating elements, and silica-brick walls designed to simulate as closely as possible the carbonizing conditions for commercial slot-type ovens. Because of the small force exerted on the oven walls in most tests conducted to date (probably owing to the practice of charging coals and blends at a moisture content approximating that normal to commercial plants operating in this district), little information has been obtained about expansion properties. Two sole-heated ovens have therefore been constructed and used as supplementary equipment for determining the expansion properties of coals tested in the Tuscaloosa oven. The reasons for constructing the Tuscaloosa oven, the details of design, the operating, characteristics of the oven and the reproducibility of results have been discussed in previous publications. 3 4 5/ The present report deals with the effects of substituting various high- and low-volatile coals for components of a selected base blend carbonized under conditions similar to those normally used for producing foundry coke. Results of tests of 11 coals and 14 blends indicate that several blends tested rave cokes having physical properties very similar to those produced from the reference blend.

Jan 1, 1957

By Gary L. Self, Ronnie Daniel

With the advent of large scale blasts utilizing overburden casting techniques, it was imperative that an ultra reliable surface delay system be developed. Shock tube and detonating cord surface delay systems have been hampered by the lack of a reliable easy-touse method of incorporating multiple paths of initiation to each hole. Two new redundant nonelectric delay systems have been developed utilizing multiple signal paths to allow a higher degree of safety and reliability. The first system designed uses a combination of detonating cord and nonelectric shock tube delays to allow multiple delay paths to each hole. The second system incorporates a new all shock tube delay system which allows multiple delay paths while minimizing over-pressure by eliminating detonating cord trunk lines. These two redundant systems have been used in over 500 production blasts without any misfires due to surface cut-offs or detonator malfunctions.

Jan 1, 1989

By Edward (Ted) Dowey

City Water Tunnel No. 3 is being built in order to provide a redundant system for delivering 4,542,500 m3 (1.2 billion gallons) of water per day throughout the five boroughs of New York City. The present tunnels, City Tunnel No. 1 and 2 (Figure 1), were put in service in 1917 and 1936 respectively, and both have been in continuous service. Tunnels No. 1 and 2 can-not be shut down for inspection or repair until City Tunnel No. 3 has been completed. City Tunnel No. 3 has two stages (Figure 1).Stage One is 20.1 km (12.5 mi) long and is presently delivering drinking water to the boroughs of the Bronx and Manhattan. Stage Two consists of the Brooklyn-Queens Tunnel 17.7 km (11 mi) and the Manhattan Tunnel 14 km (9 mi). The Brooklyn-Queens leg is complete and is set to be put in service soon. The Manhattan Tunnel is being constructed and is the subject of this paper. The Manhattan Tunnel (Figure 1) is comprised of three legs: the north, south and east legs. The con-tract includes the excavation of 8,976 m (29,500 ft) of tunnel and the lining of 14,561 m (47,773 ft) of tunnel. The south tunnel, 5,705 m (18,720 ft), was excavated but not lined, under a previous contract. The tunnel ranges from 181 m (600 ft) to 152 m (500 ft) in depth in the bedrock under Manhattan. The tunnel contract also includes the construction of nine new shafts, 161 m (530 ft) average depth, and the completion of a tenth shaft (the previously built construction shaft). The Manhattan Tunnel contract was awarded to the sole bidder Schiavone/Shea/Frontier Kemper Joint Venture (SSF) for $668,532,680.00, on January 31, 2005. The Manhattan Tunnel was designed ?in house? by the New York City Department of Environmental Protection (DEP) and the construction management was provided by a combined staff of the DEP and a joint venture of Jenny Engineering and URS.

Jan 1, 2008

By John R. Marks

Introduction An engineer is a builder and a problem solver. He uses knowledge of the properties of matter and energy to furnish the needs of society. Engineers form the bridge between scientific researchers and the general public, most of whom are technologically illiterate. Mining, metallurgical, and petroleum engineers extract minerals from the ground and process them into usable forms. Then, other engineers further process them into society's needs. Minerals engineers deal with more uncertainty than other engineers. Each ore deposit has its own personality and each ore is metallurgically unique. Minerals engineers, therefore, must be flexible, often applying larger safety factors and contingencies than other engineers, and frequently functioning as a jack of all trades. A minerals engineer can work in coal, oil, oil shale, base metals, ferrous metals, precious metals, industrial minerals, strategic minerals, or in exploration. Other mining jobs include banking and financing, education and research, marketing and sales, and government. As a minerals engineer, you may be among the first to work on the ocean floor or the moon. College Preparation A difference between college and industry is the type of problems to be solved. A typical college problem has an exact answer derived from given information. An industry problem is more apt to have a solution chosen from a number of alternatives. Information required for the solution is not given. It must be measured, calculated, looked-up, estimated, or otherwise derived. Solutions involve trade-offs, economics, and human factors, as well as application of physical laws and theory. When a college problem is answered, you move on to the next one. In industry, however, the headaches may just be starting with the implementation of the solution. Students often complain that they see little use for the theory they are learning. This is valid. A good professor will link theory and practice. Another difference between college and industry is the price of failure. In college, you can make a half-hearted effort in an assignment and take your C or D. On the job, however, poor engineering results in potentially effective projects being rejected and unsound projects being undertaken. Poor performance results in cost overruns, schedule holdups, oversights, disgruntled employees, irate bosses, unsafe structures, and unreliable systems. The costs are time, money, and possibly lives. The student pays the university for his work - not the other way around. So the rewards for good schoolwork often seem nebulous. But education must be viewed as an investment. Working for good grades will help you think better, learn more, receive better job offers, and perform more effectively on the job. There is no substitute for hard work. Avoid taking the easiest electives. If you desire a more liberal education or dislike rigorous physical sciences, mathematics, or engineering courses, change majors. Remember, you are training to be an engineer, not a computer programmer or market analyst. At least one summer of industry employment is necessary for minerals engineering students. The sooner you gain actual experience, the sooner you will know whether to change majors. Most large companies hire students during summer. It is best to send out applications around Christmas break. First and second year students usually work as laborers. Upper-classmen may work as engineering technicians. Students must sometimes choose between returning to a company at a higher position or trying a different company at a lower position, for more varied experience. Both alternatives have advantages. Do your best on these summer jobs. The company is watching. If you do well, the chances are good you will get a job offer when you graduate. Good references are important when you begin job hunting. Interviewing occurs near the end of your school career. The standard procedure is to send your resume with a cover letter to each company you are interested in. The resume for a graduating engineer with little experience need not exceed one page. The cover letter must be written for the individual company.

Jan 2, 1985

By V. A. Marple, K. L. Rubow, S. M. Behm

"An eight-stage cascade impactor, with cut-sizes ranging from 0.056 to 18 um at a flow rate of 30 L/min, has been developed, calibrated, and tested in field programs. This impactor, called a microorifice uniform deposit impactor, has several features not normally found in cascade impactors. Ultrafine particles as small as 0.056 um are collected while keeping the pressure drop moderate by utilizing multiple nozzles (up to 2000) as small as 52 um in diameter. At each stage the collected particles are deposited uniformly over the entire impaction plate by rotating the impaction plate relative to the nozzles and by the correct radial placement of the nozzles. The particle cutoff characteristics (collection efficiency curves) of each stage and inter-stage losses were determined by means of monodisperse aerosols. The cutoff characteristics were found to be sharp and similar for all stages.Inertial impactors are widely used for the size-selective collection of aerosol particles. One reason for their wide usage is that the principle of operation is simple: a jet of particle-laden air is directed at a flat impaction plate. Large particles are collected on the plate while smaller particles follow the airflow out of the impaction region and are not collected. The division between the size of particles collected and those that are not is quite sharp. Secondly, the particles in an impactor are classified by their aerodynamic diameter (an important size parameter in many fields of study, including those related to respirable particle health effects). Thirdly, it is easy to collect particles in discrete size ranges by passing the aerosol through a number of stages (one stage consisting of a nozzle and impaction plae) in series, with each subsequent stage collecting particles smaller than the one before it. This is known as a cascade impactor. Finally, impactors can classify particles over a wide range of particle sizes: as low as 0.005 um (Fernandez de la Mora et al., 1990) and as large as approximately 50 um (Vanderpool et al., 1987).This paper describes a general purpose cascade impactor that has been developed in our laboratory and used in a variety of studies including visibility studies (McMurry et al., 1986; McMurry and Zhang, 1989), underground mine studies (Marple et al., 1986; Rubow and Marple, 1988; Rubow et al., 1988), and general atmospheric pollution studies (Macias et al., 1981; Dzubay et al., 1984). The impactor, called a microorifice uniform deposit impactor (MOUDI model 100, MSP Corp., Minneapolis, Minn.), is the integration of two earlier impactor de¬velopments: the microorifice impactor (M01) (Kuhlmey et al., 1981) and the uniform deposit impactor (UDI) (Marple et al., 1981).The MOUDI has several features normally not found in other cascade impactors. These include collection of particles as small as 0.056 um in aerodynamic diameter with a moderate pressure drop, uniform particle collection on the impaction plates, inter-changeable impaction plates to allow for the plates to be easily and quickly changed in the field, and covers for these substrates to provide a means for safe storage and/or transport of the collected particles to the laboratory for analysis."

Mar 1, 1992

By O. M. Bishop

"SUMMARYAs a result of the increased demand for fluorspar during the war, the Bureau of Mines investigated numerous fluorspar properties in the southern Illinois field, which is centered in Rosiclare. Among these the J. J. Shelby 40-acre tract on the western edge of the district presented favorable factors that caused it to be chosen /or exploration.H. G. Spiller, formen lessee of the property, had explored the Shelby vein by means of an adit level and winze, and showed it to contain goad values in zinc and fluorspar at the depth explored. A diamond-drill hole with which Spiller explored the vein 78 feet southwest of the winze, however, failed to cut ore. After studying the field evidence, the Bureau concluded that the vein merited further exploration, particularly at a depth of about 440 feet, where the Fredonia limestone would form the foot-wall of the vein and the hanging wall would be the competent Cypress sandstone.Between October 17, 1944, and March 26, 1945, three diamond-drill holes were bored for a total inclined depth of 1,592 feet. Holes 1 and spaced approximately 500 feet apart, explored the vein at 440 feet 4 below the surface. The economic mineralization existed in the vein where cut. Hole 3 cut the fault at approximately 300 feet below the outcrop but failed to find any vein matter except stringers of calcite with small amounts of pyrite."

Apr 1, 1947

By James M. Stauffer

There are many types of filters designed to separate a solid from a liquid, including plate and frame presses, pressure leaf filters, gravity filters and vacuum filters. This discussion will be limited to continuous vacuum filtration and, specifically, to continuous rotary vacuum disc filters, drum filters and horizontal belt filters. The use of vacuum filtration can be advantageous in that: 1. The feed slurry can be delivered to the filter either by gravity or by a simple, inexpensive low pressure pump that only has to overcome the resistance of the feed piping system. 2. The filter equipment does not have to withstand high pressures. Consequently, a wide range of materials of construction, including plastic and fiberglas reinforced polyester (FRP), can be used in the fabrication. 3. After the form time, the filter cake is exposed to the atmosphere and the cake is accessible for further operations such as mechanical or physical dewatering, washing, and sampling on a continuous basis. 4. The discharge of the dewatered solids is continuous for directly feeding to the next operation; for example, a dryer. 5. Various methods of discharge can be fitted to the filter to effect optimum discharge of the dewatered cake solids. The principal of operation of a vacuum filter, regardless of type, is basically the same. The filter incorporates a filter medium supported on a drainage system and arranged so that the mixture to be separated (feed slurry) can be introduced to one side of the filter medium on which the solids are trapped and through which the liquid (filtrate) flows due to the applied vacuum.

Jan 1, 1979

By O. M. McRae

The Courtland-Gleeson area is in Cochise County about 15 miles east of Tombstone in southeastern Arizona. Rocks exposed in the area range in age from Pre-cambrian to Quaternary. The Precambrian is repre-sented by the Pinal schist. Paleozoic rocks include the Cambrian Bolsa quartzite and Abrigo limestone, Mississippian Escabrosa limestone, and the Permo-Carboniferous Naco Group limestones. Rocks believed to be of Triassic and/or Jurassic age include the Copper Belle monzonite porphyry, Turquoise granite, and Gleeson quartz monzonite. The Cretaceous is represented by andesitic volcanics and various sedimentary rocks. Tertiary rocks include the intrusive and extrusive Sugarloaf quartz latite porphyry and numerous dikes of various rock types. Quaternary conglomerates cover the northern and eastern part of the area. The geologic structure is extremely complex. All rocks as old as early Tertiary have been involved in either tilting, normal faulting, high angle reverse faulting, imbricate thrusting or folding and overfold-ing. Major deformation was initiated during the first half of the Tertiary. Northeast-southwest compres-sional forces caused thrust plates containing lower Paleozoic rocks to override Cretaceous rocks. Subsequently, two large slide blocks of lower Paleozoic rocks, acting under the influence of gravity, moved eastward. The imbricate structure and the gravity slide blocks were then broken by late Tertiary normal faults. INTRODUCTION The Courtland-Gleeson area, or Turquoise Mining District, has long been recognized as an area of extreme structural complexity. Gilluly 2 referred to the entire district as a "gigantic thrust breccia". In 1962, Bear Creek Mining Company completed a two year program of detailed geologic mapping supported by exploration drilling. The purpose of this paper is to present some of the results of this investigation and to provide a structural interpretation based on these results. The geologic map that accompanies this report is generalized and shows only the major and significant features. The area was initially mapped on aerial photographs on a scale of 1 in. equals approximately 500 ft. These data were transferred to a planimetric base using a vertical sketch master. LOCATION The Courtland-Gleeson area is in central Cochise County, about fifteen miles east of Tombstone, and about twenty-two miles northeast of Bisbee in southeastern Arizona (Fig. 1). The area is readily accessible over graded gravel roads from both Tombstone and Elfrida. GENERAL GEOLOGY Rocks exposed in the area range in age from Pre-cambrian to Quaternary. wilson3 and Gilluly2 have published very detailed descriptions of the principal rock units exposed in the area. Only a summary description is provided in Table I. A great number of previously unmapped narrow Tertiary dikes and small irregular masses of hornblende andesite porphyry, lamprophyre, and aplite intrude the Gleeson quartz monzonite in the western part of the map area. The scale of the map prohibits showing them. The aplite dikes are related to, and bear the same structural relationships as, the Sugarloaf quartz latite dikes found in this area. For that reason, and because both the hornblende andesite porphyry and the lamprophyre are post-mineral and post-thrusting, their omission from the map is not considered significant. Because so many of the contacts in the district are fault contacts, because bedding faults appear to be prevalent but are difficult to recognize and map, and because igneous intrusions are so common throughout the sedimentary section, it is virtually impossible to measure an exact total thickness of any of the sedimentary rock units. Nevertheless, neither the field mapping program nor the diamond drilling provided any basis for suspecting that the thicknesses of the sedimentary units are significantly greater or less than what might be inferred from surrounding districts.

Jan 1, 1967

By I. Y. Motovilov, S. A. Telkov, M. B. Barmenshinova, Z. S. Abisheva

As a rule, removing waste rock at the beginning of the process improves the conditions for the flotation of minerals, and also reduces the operating costs of crushing, grinding and flotation. Lead-zinc ores in the Shalkiya deposit of the Republic of Kazakhstan are classified as difficult for enrichment, but taking into account their significant reserves, they are one of the main potential ores for the production of lead and zinc. Under industrial conditions, for processing ores of the Shalkiya deposit, a selective flotation concentration scheme with the production of lead and zinc concentrates is recommended. However, according to the recommended scheme, it is not possible to obtain high-quality concentrates of lead and zinc, with high metal recovery. The paper presents the results of studies of preliminary gravitational enrichment of lead-zinc ore in the Shalkiya deposit. Based on the fractional analysis for the particle size range of -40+8 mm, Henri- Reingard enrichment curves were constructed, separation density (2730 kg /m3) was established to isolate the light fraction with the lowest possible lead and zinc content, and gravity enrichment indices (0.7-0.71) were determined. It was found out that when using gravitational enrichment of the original large-sized ore in the Shalkiya deposit, tails are released at the beginning of the technological process with a yield of up to 20% with the extraction of silica up to 30%, calcite up to 11% and carbonaceous matter up to 12%. As a result of the studies, it was found that the beneficiation of crushed lump ore could be conducted in heavy suspensions. One of the positive aspects of the use of gravitational enrichment is the reduction of energy costs for grinding the heavy fraction, which was experimentally proved in this article. Keywords: Lead-zinc ores, Shalkiya deposit, fractional analysis, gravitational enrichment, floating fraction, sunken fraction, separation density

Jan 1, 2020

By K. Ghyselbrecht, R. Swennen, Y. W. Chiang, V. Cappuyns, R. M. Santos, T. Van Gerven, B. Meesschaert

Heavy metal contamination from mining and metallurgical activities of aquatic systems poses significant risk to the environment and human populations. The investigation of the distribution and immobilization mechanisms of heavy metals in sediments and soils has recently attained high priority. Different remediation methods can be employed to suppress or eliminate these contaminants. A tailored approach using both commercially available and in-house made adsorbents to rem ediate a heavy metal contamination site due to historical metallurgical activities in north Belgium is studied in this paper.

Jan 1, 2011