Search Documents

By C. M. Brinckerhoff

Safety work in mining at the Andes Copper Mining Company, Potrerillos, Chile, is divided into three parts: (1) accident prevention, (2) fire prevention and protection, and (3) silicosis prevention and control. In the company's operations a steady campaign has been waged to reduce accidents and silicosis, and to prevent fires. In the following pages the safety record for the past twelve years will be examined and the methods explained by which the accident rate was reduced. Table 1 contains yearly data pertaining to the scale of the mining operations and the accident record. Block caving is used for all ore production and the tonnage mined has aver- aged 30,000 short tons per day for the past seven years. Table 2 classifies 44 fatal accidents which have occurred since 1935. The leading causes of accidental death are transportation of ore and use of explosives, followed in order by per- sons falling, falls of ground, and by asphyxiation. In the case of serious accidents, however, the greatest cause is falls of ground, followed, in turn, by ore

Jan 1, 1949

By F. Z. Suo

Baoahan Iron and Steel Complex is situated at lower beaches of the Yangtze River. The subsoils 50~70 M below the surface is a deposite of Yangtze River delta, consisting mainly of weak silty clay and loam, with low soil bearing capacity. Consequently, to build on such a weak soil a grant iron and steel integrated works weak soil improvement at the Complex, pile foundation is the effective type. It is estimated that at the first stage of Baoshan project 60,000 piles have been driven, of which 60% are steel pipe piles and 40% reinforced concrete piles. To provide reliable basis for pile foundation design, on-site loading tests were carried out for long reinforced concrete piles 27,45 60 M in length ,with strain gauges on the chief reinforcement of pile shaft and strain rod on pile tip. Based on loading tests, the paper discusses and analyses some issues, including determination of load transfer mechanism distribution of frictional resistance. Tests show that as far as long friction piles in soft clay are concerned, regardless of the properties of pile tip's bearing stratum, loads are mainly carried by shaft frictional resistance which it is effective to determine pile capacity in terms of P ~ S relationship.

Jan 1, 2010

By Bernard Porter

The solubility of UO2 was determined at 1,250° C. in ternary melts of UF4 and BaF2 with CaF2, LiF, and SrF2. The solubility of Ce02 was measured at 800° and 850° C. in a solution of CeF3, BaF2, and LiF. The amount of La203 which dissolves at 950° C. in a binary mixture of LiF and LaF3 and a ternary of LiF, LaF3, and BaF2 was also measured. In each case, the amount of soluble oxide was mound to be less than 5 weight-percent. A procedure was developed for filtering fused, oxide-saturated fluoride melts in order to obtain a representative sample for chemical analysis. The oxide content of the samples was determined by an inert-gas fusion procedure.

Jan 1, 1961

By L Ventura, M Almond

The Pueblo Viejo project in the Dominican Republic installed an innovative sample system on its reverse circulation (RC) drilling rig during commissioning and subsequent commencement of operations. As knowledge of the orebody increased with mining and plant production, cost pressures became apparent that raised questions concerning the continued use of RC drilling versus blasthole sampling for ore control.To justify the continued use of RC drilling for grade control, an in-depth study was undertaken to determine the quality of the sample and prove its value-add to the operation.To investigate the differences in sample quality, a complete bench trial was initiated across both ore pits to compare RC drill results with blasthole assays on a side-by-side basis. The results indicated that based on ore block comparison between RC and blasthole sampling, RC identified an additional 20 per cent of high-grade (+ 4.5 g/t Au) ounces.Previous work indicated that Au, Ag and Cu were all elevated in the drill fines at Pueblo Viejo (Goers and Almond, 2012). This previous test work did not consider the quantity of fines in an RC sample therefore new test work was undertaken to include particle size distribution analyses. This study would determine if the inclusion of fines in the sample was occurring and compare the quantity of fines in the sample against other sample systems and blasthole samples.Comparisons between RC samples and blasthole samples indicate that for the RC samples a range of 30–35 per cent of the sample passed 300 mesh as compared to blastholes where the range of the sample passing 300 mesh was 15–30 per cent.This paper includes a case study on the importance of accurate samples and how they have impacted throughput through the pressure oxidation process plant at Pueblo Viejo. The accurate samples provided by RC allow for improved stockpile and blending strategies, showing the importance of accurate samples to manage risk and create value, against the perception that savings can be made at the risk of poor sampling performance.CITATION:Almond, M and Ventura, L, 2017. Adding value with reverse circulation drilling at Pueblo Viejo, in Proceedings Tenth International Mining Geology Conference 2017, pp 277–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By D. A. Robbins

The Resource Conservation and Recovery Act. of 1976 (RCRA) requires testing of waste materials as part of the determination of whether these materials are classified and managed as hazardous wastes. The adoption of one standard testing procedure and its application to all types of waste materials has stirred much controversy. In the center of this controversy is the appropriateness of this testing procedure in characterizing non-ferrous metal intermediates and slags. The authors have evaluated the relative availability of metals in several types of copper and lead slags as defined by various testing protocols. Also discussed is the relationship between the chemical character of the slag and the availability of metals to leaching and certain metallurgical practices that can influence metals availability.

Jan 1, 1983

By Willemijn Husslage

Tata Steel Group At a glance ? Part of the Tata Group ?Tata Steel Group: ?Fortune 500 company ?Top 10 global steel producer ?Annual crude steel capacity of 28 million tonnes ?More than 80,000 employees ?Manufacturing operations in 26 countries across 5 continents ?Serving customers all across the globe ?Turnover 2009-10: $22.8 billion

May 1, 2011

By Saba Mohan

This study presents results based on the Pile Installation Demonstration Project (PIDP) that was conducted as a part of the East Span San Francisco-Oakland Bay Bridge Seismic Safety Project. For the three full-scale pile installations, two different high-energy hydraulic hammers were selected for the installation. However, these hammers may not have sufficient energy to drive these large diameter piles at their ultimate capacity following long-term set-up. Nevertheless, these hammers were selected because, soil plug behavior, the generation of excess pore pressures and remolding of soil during driving were expected to reduce the shaft and end bearing resistance, and therefore reduce the energy required to drive these piles to design penetration. Data collected during continuous installation driving and after a series of re-strikes at different set-up times ranging from 1 to 33 days were used as input data for CAPWAP. These results were used to estimate the soil resistance along the pile length and at the toe of the pile, and the soil pile set-up behavior. Validity of the procedures used to predict the soil resistance to driving and predicted blow counts were verified with the field observed blow counts and the energy that was delivered to the pile. Based on combined CAPWAP analyses, the soil pile set-up with time was estimated and compared with results of other methods currently available in the literature for predicting the soil pile set-up rate.

Jan 1, 2002

By W. L. Josey

The Stibnite Project is an open pit/cyanide heap leach gold property located in the Yellow Pine mining district of central Idaho. The gold ore is in an oxidized zone of an epithermal deposit which is associated with a fault system related to Tertiary igneous activity of the region. The faults transect a roof pendant of metamorphosed sediments within crystalline rocks of the Idaho Batholith. Seasonal mining is at a rate of 3900 mt/d (4300 st/d) of ore with a 2:l waste to ore ratio. Gold and silver are recovered through a process of cyanidation, carbon adsorption and desorption, and electrowinning. Disposal of the leached ore requires chlorination of the residual cyanide.

Jan 1, 1984

By Omid Frough, Hossein Changani

Application of Tunnel Boring Machines (TBMs) is one of the main solutions to achieve a safe and high-performance method of construction in hard rock and soft ground tunneling. In order to adequately assess the progress and potential impacts of the tunneling operations with the TBM, it is required to record a series of data during the tunneling and process of the data to evaluate the TBM performance. Applying the right machine parameters during the excavation not only delivers an optimum penetration rate, but also prevents extra downtime due to over excavation or wear of cutting tools. In this paper, the effect of machine and operational parameters on TBM downtimes has been studied and supported with the real examples of TBM operation data.

Dec 1, 2022

By Rod L. Norfleet

Cemented tungsten carbides are a sintered powder - metallurgical product essential to modern industry. Because of their moderate unit price and our dependence upon foreign sources for the component raw materials, a growing recycling industry has developed in the United States. There are two basic approaches taken to recycling cemented carbides; those which leave constituting materials unaltered or direct-reuse and those which separate the constitutes back to the raw components. To separate the carbides back to their raw components usually requires expensive chemical processing and is thus confined to the lower value materials such as grinding sludges. The direct-reuse methods recycle cemented carbides back to an intermediate level, a powder capable of being recompacted and resintered into a functional end-product. The three most commonly used methods of direct-reuse recycling, the coldstream process, bloaching and the Bernard or zinc process, are reviewed,

Jan 1, 1984

By B. J. Arnold

During the past three years, coal samples covering a range of coal rank, ash content, size consist, grindability, and moisture content have been tested for their flow properties using a triaxial shear tester that measures the unconfined yield strength in a compressed sample of coal. The ratio of this unconfined yield strength to the sample bulk density is part of the equation used by handling system manufacturers to calculate the critical arching or critical ratholing diameter needed to ensure that coal will flow from bunkers or bins. This ratio also serves as an index to compare the flow tested. To test the applicability of the index to predicting problems with coal flow, a series of tests were conducted at CO Inc.'s Coal Quality Development Center (CQDC) in Homer City, Pennsylvania. Tests covering ranges in size consist, moisture content, and ash content were conducted by first filling a small two-ton bin with coal and then emptying the bin at a pre-set discharge rate. The actual discharge rate from the bin under the various conditions tested was measured. Samples of the coal discharging from the bin were collected. One sample was analyzed for ash, moisture, and size consist; another sample was sent to the Iowa state University for trivial shear tests (supplying an index measurement). Actual flowability results from the bin were then compared to the measured index to determine the applicability of the handleability index in actually predicting coal flow problems. This paper describes the correlation between handleability index and bin flow and explains the next stages of the project.

Jan 1, 1992

By T. D. Arnold

The Barrick Bullfrog underground mine was established as an afterthought to the main open pit. As open pit ore dwindles, the underground mining becomes increasingly more important as an ore source, and to the overall economics of the project. This situation is similar to many other mines, and there is a strong move towards underground mining in the United States today. There are inherent problems in starting and operating underground mines in the shadow of any open pit operation, and at the Bullfrog there were several attempts at productive increases that were both successful and unsuccessful.

Jan 1, 1996

By MANZOOR ALI BROHI, IZHAR MITHAL JISKANI, Atta Ur Rehman, SHUAI HAN, MUHAMMAD TARIQ, NIAZ MUHAMMAD SHAHANI

A thorough improvement in mine safety is contingent on many factors that require scientific decision-making for selection and prioritizing of important factors for safety improvement. Their analysis using an established scientific method can improve mines’ safety conditions and assist the administration for informed decision-making. This research establishes a mine safety evaluation index and proposes an integrative model based on the entropy weight and grey clustering methods. In the evaluation index, 27 significant factors of safety are identified and categorized into 7 criteria. The proposed evaluation system analyzes all indicators according to Pakistan’s current mine safety situation and their significance for potential safety improvement in the future. Results reveal that current safety practices are outdated due to a lack of mechanization in the mining industry and minimal capability of the management to achieve the desired safety targets. Appropriate safety policies and safety education are missing in the daily working environment. The lack of overseeing the execution of safety operations and the lack of ambition and strong work ethic workers contribute to the paucity of mines’ safety conditions. The prevention and control systems to manage risks and hazard are not in place, and the working environment in mines remain difficult. Therefore, to have enhanced mine safety, important factors can be addressed in chronological order, as presented in this paper. The proposed methodological approach can be applied to other prioritization applications to analyze the indicators and determine the appropriate management strategies.

Jun 14, 2021

By Tracy Brettmann

In recent years the Augered Cast-In-Place (ACIP) Pile industry has seen a substantial increase in the quality control options available to Contractors, Engineers, and Owners. Quality control methods range from the simple, manual techniques that have been used for years to new computerized installation monitoring equipment and nondestructive testing methods. Our ability to monitor and test ACIP piles has grown to such a degree that the industry is struggling to determine how much quality control is enough. This paper reviews the many options available and describes the pros and cons of each. The various nondestructive testing methods, in particular, have been difficult to apply reliably due to misapplications of methods and misinterpretation of the results. ACIP piles have unique properties that require the various nondestructive testing methods available be considered very carefully in determining the method most appropriate for a particular use. Some nondestructive testing methods, as well as automated monitoring equipment, potentially can be applied effectively to increase the level of quality control for ACIP piles. The experience gained on real projects using these new methods, in conjunction with the old procedures, provides valuable information for future applications.

Jan 1, 2000

By Pablo González, Rodolfo Espinosa, Jose-Luis Noyola, Sergio Cossio

"Minera Penmont, at La Herradura, is a joint venture between Industrias Peñoles, S.A. de C.V., and Newmont Mining Corporation. The mine is located in the northern Mexican state of Sonora. La Herradura consists of an open pit mine with two-stage crushing and heap leaching facility, the gold is recovered from the pregnant solution using the Merrill-Crowe process; production began in July 1998. La Herradura produces about 130,000 gold ounces per year, and treatment capacity is 22,000 tonnes/day. Ore mineralization occurs in a shear zone with quartz and native gold. Gold distribution is quite heterogeneous due to the coarse visible gold, in some coarser particles ranging from 100 to 600 microns.Sampling and assaying protocols where established during exploration and prior to starting up operations, based on nomographs developed from early heterogeneity tests. But, as the coarse gold problem became noticeable, it was necessary to develop new sampling protocols to have an acceptable relative standard deviation to control the fundamental error within ± 15%.An experimental program was developed and conducted on a selected ore block made of 195 blastholes; regular ore grade control procedures were applied to both sets of data to evaluate the difference in results between the protocol established prior to starting up operations (“existing”) and the new protocol (“leaching”). In the “existing” protocol, subsampling is done through riffle splitters, and coning and quartering. Fire assaying is used to estimate the gold content, on a 50 g sample. In the “leaching” protocol a 12,000 g sample was bottle rolled cyanide leached, and the leach residue was assayed on a 50 g sample using fire assaying, and a weighted average total gold content was calculated. Currently, a new alternative method is being evaluated, where sub-sampling is done using rotary splitters, and fire assay on a 50 g sample; in this “rotary sampling” protocol and for comparison purposes, gold assays were also repeated using the “leaching” protocol.Test results were compared in three groups < 0.30 g/t (below cut-off), 0.30 to 0.8 g/t, and >0.8 g/t. Overall. Results show that the protocol established prior to starting up operations underestimates the gold assays. Detailed technical results, alternative options, and their implications are discussed in the paper."

Jan 1, 2003

By M. Rufli

Until not so long ago most ring geared mills were operated with fix speed motors only. By using the latest generation of medium voltage frequency converters, new possibilities have arisen to improve the grinding process. Beside all the direct and indirect advantages, several dedicated functions have now been implemented for ring geared grinding mills in the minerals industry. The sophisticated operational functions ensure a smooth, safe and reliable operation with minimum stress for the mechanical equipment and therefore utmost availability of the mill. Several papers have already been presented concerning the benefits of using this state of the art technology for mill drives. Now this paper is focusing on the experiences gained with this kind of sophisticated ring geared mill drive system rather than only show and explains the operational benefit of the different functions. Several measurements of different operating conditions, starting, frozen charge remover, controlled roll back, backlash, etc., made on an installed and commissioned 2 x 5 MW dual pinion ring geared mill drive system will be shown and discussed. The accuracy of the load sharing between the two 5 MW motors during starting, normal operation and stopping will be demonstrated using real measurements from an operating system. Finally the inherent features of these drive systems are briefly discussed.

Jan 1, 2011

By Y. J. Zhang

This paper presents the results of a recent study on the development of an in-situ testing method for determining the coal strength in mine pillars. The strength testing is performed in the horizontal holes drilled into the coal rib using the penetrometer. It is a hydraulically powered device that uses an indenter to press the surface of the borehole until the load reaches the failure point of coal. The pressure and the penetration of the loading pin are recorded by the data acquisition unit. The results collected from several coal mines indicate that this testing method is ideally suited for the realistic coal strength measurements. The new testing system not only improves the accuracy of pillar strength determination, but it is more cost efficient than the conventional method.

Jan 1, 1995

By T Raynlyn, J J. Campbell, R J. Holmes, J R. Manuel, S P. Suthers, A Poliakov

Prediction of the downstream processing performance of iron ore needs detailed information on mineral composition, textural peculiarities, particle density, porosity, mineral liberation and association and mineral grain size. Optical image analysis and automated iron ore texture classification systems are a way of obtaining such information. Furthermore, this information can be used for predicting the output of specific processes and their combinations. Several examples of the application of such an approach to process performance studies for iron ore are discussed. These include the application of classification by ore texture to modelling and optimisation of hydrocyclone performance, the effect of including textural information in modelling of sinter properties, and combining textural information with an experimental study of stirring and ultrasonic treatment of haematitic-goethitic iron ore fines to understand the deportment of fines and the breakdown/deagglomeration of particles. In all cases, the availability of textural information is important and helps provide a better prediction of process performance and/or understanding of the unit process.

Jan 1, 2008

By C. R. DeGennaro, Yongjun Zhang, J. Bickson, J. L. Carr, Chenming Zhou, J. R. Srednicki, B. Lambie, M. Girman, J. A. Galanko

Between 2005 and 2021, surface mining haul trucks were involved in 54 fatal incidents in the United States [1]. Collision warning and avoidance systems (CXS) can help haul truck operators navigate their route safely. The evaluation of CXS object detection performance for surface mining haul trucks relies on the positional accuracy of the ground truth instrument. As part of a holistic approach, researchers from the National Institute for Occupational Safety and Health (NIOSH) characterized the accuracy of a global navigation satellite system (GNSS) that serves as the ground truth instrument to determine object position and velocity in CXS object detection performance testing. We used precision surveying equipment to establish ground truth points for comparison with GNSS data collected for static positional measurements and reduced-scale straightline vehicle dynamic tests. We conducted these tests with real-time kinematics (RTK) and then satellite-based augmentation systems (SBAS). For the dynamic tests, we measured a distance error of 1.34 m (4.40 ft) using RTK and 1.50 m (4.92 ft) using an SBAS. This research will provide CXS manufacturers and CXS researchers a basis for evaluating the positional accuracy of CXS. Note that we did not evaluate any CXS in this experiment.

Feb 1, 2024

By P. Felix

A discussion on the need of visualization and animation tools in modelling solidification processes is made. An outline of an approach for the production of a video computer animation is provided. A number of examples including, 2 and 3 dimensional melting, filling, and macrosegregation are presented.

Jan 1, 1993