Search Documents

By S. A. Shoop, J. J. K. Daemen

Site-specific blast vibration prediction can be more accurate than using a universal prediction equation. Vibrations from 37 blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly, inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations predicted from US Bureau of Mines (USBM) equations. Vibration restrictions based on USBM studies could then be too conservative or too lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases, energy was concentrated at frequencies corresponding to delay intervals.

Jan 3, 1985

By Ramin Motamed, Joseph A. W. Toth

Evaluation of the capacity of large-diameter drilled shafts using current load test methods present challenges when considering the magnitude of loads required to fully mobilize their capacities. Often, these full scale tests do not fully mobilize the capacity through side resistance. Therefore, the need for innovative solutions to extrapolate side resistance and interpret nominal capacity are of key interest. In this study, we evaluate three methodologies for extrapolating unit side resistance based on bi-directional load test data. Fellenius (2001) presented these methods for interpretation of pile capacity using static load tests. Our interpretations are based on the evaluation of 116 load tests. Unit side resistance was calculated and reviewed for each load test and categorized using three criteria of mobilization; (A) full, (B) partial and (C) linear. This study specifically focuses on load tests that showed fully mobilized unit side resistance behavior (Criteria A). The three methodologies were applied assuming Criteria (A) load tests were mobilized to 50% of their measured values. Subsequent comparisons of each extrapolation were then compared against the full measured values for each test and generally showed good agreement. INTRODUCTION It is widely accepted that conducting load tests such as standard top-down tests or bi-directional (i.e. O- cell) tests can help designers understand load-settlement behavior and the nominal resistance of drilled shaft foundations. These load testing methods provide the advantage of confirming design assumptions as well as improving the reliability of the foundation design. The potential cost savings from the application of these methods for mid to large size projects is self-evident. For example, in a recent project in Northern Nevada, an O-cell test on a 6.9 ft diameter, 114.8 ft length drilled shaft imposed an initial cost of $125k to the project, resulting in a 15% reduction on the total foundation cost; equivalent to $1.3 million in overall savings (Pease, 2014). However, the costs of implementing such methods on smaller projects can be prohibitively expensive (Hagerty et al, 2016). Despite the clear advantages of drilled shaft load testing, the current practice is not without limitations. Performing load tests on large-diameter drilled shafts with high capacities is a challenge considering the significant loads required to fully mobilize the capacity of such foundations. In some cases, the feasibility of these tests is impractical because the associated initial cost is not guaranteed to outweigh the final savings. As a result, large scale load tests are sometimes ruled out from the design phase of projects. Furthermore, in the majority of load tests the magnitude of loads applied are specifically selected to not approach failure, so the shafts can be used in the future foundation system (i.e. production shafts). This practice of field testing restricts our knowledge of the true capacity of the drilled shaft at failure; hence the nominal resistance remains unknown.

Jan 1, 2018

By M. B. Dusseault, A. Pirayehgar

"There is concern that hydraulic fracturing (HF) near an existing critically stressed fault could trigger slip and generate a seismic event of significance. To this end, a mathematical discontinuum model representing a naturally fractured rock (NFR) mass containing a fault is created, and fault slip response to fluid injection is studied. UDECTM is used as a Discrete Element Method (DEM) approach to define the seismic moment, and also to assess the influence of injection and slip on further shear slip propagation. In most of the simulations, slip and dilation take place along a number of oriented fracture surfaces, so it is reasonable to assume that in a real case, microseimic emissions would accompany each slip “event”. The moment magnitude scale (Mw) is used to measure the size of the microseismic event in terms of the energy released. Seismic moment is a measure of the total energy (work) released during a seismic event and is used to measure its size. From another aspect, the injection energy is calculated as the total energy required for achieving the hydraulic fracturing; this is viewed as energy to open fractures against the ambient stress field and much of it is potential stored energy that can be released and create discontinuities (work of fracture), deformations (W=F·d), heat and radiated seismic energy. A small amount of the total released energy is transformed to radiated seismic energy and another small amount results in tensile fractures. Fracture energy is used to calculate the work required to create fracture surfaces. Comparing the energy release by fracturing or seismic events indicates their contribution to the total amount of released energy or total work. The amount of energy associated with the stick-slip event is small compared with the overall work done to generate the distortions (i.e. increases in aperture by forcing them open) in the rock mass, and much of the energy in slip is lost as heat from the plastic deformation, rather than as radiated seismic energy.Microseismic monitoring shows the spatial distribution and magnitude of seismicity associated with slip of bedding planes and natural and incipient fractures. Work calculations have been undertaken to look at the various sources of energy storage (elastic strain energy) or dissipation (slip), and likely the energy losses from viscous dissipation could be addressed as well, helping to clarify HF processes in NFRs."

Jan 1, 2015

By G Tranell, E Pastor-Vallés, A Vallejo-Olivares, J B. Pettersen

Metals are essential for the sustainability transition and decarbonisation of society. Yet, it will be paramount to produce them sustainably and minimise the affiliated resource and energy use and the associated emissions. In the circular economy, the metallurgical industry should recycle existing material stocks, and improve its utilisation of wastes, residues and side streams. This increases the complexity of processes, as they become both (often multi-fraction) waste treatment as well as material production processes and brings complexity to the assessment of environmental benefits. Assessing the environmental impact of technological developments frequently is supported by life cycle assessment (LCA). While the method is well documented, its implementation involves several methodological choices that deserve reasoning and analysis, such as how to define the product when former wastes are turned into new products, the selection of impact methodology when converting emissions to environmental indicators, the definition of system boundaries and co-product allocation and the interpretation of sensitivity and uncertainty in final outcomes. In this exploratory study, we investigate how the variation of LCA set-up affects the environmental burden of the system. We consider a metallurgical process where a mix of hard-to-recycle aluminium-containing streams is used to produce aluminium cast alloys in a rotary furnace. Remelting with salt-fluxes allows recovering metals from partly oxidised/contaminated streams, such as dross, bottom ash and industrial shavings, but at the expense of generating significant amounts of salt-slag/salt-cake hazardous waste. The study considers different system alternatives such as landfilling the salt-slag residues versus valourising them into salts, aluminium concentrates, ammonium sulfate and non-metallic-compounds to be used by the metallurgical, construction or chemical industries. Practical recommendations are outlined to facilitate the implementation of LCA in assessing the potential benefits of the circular economy in the metallurgical sector.

Aug 21, 2024

By Charles T. Holland

ANALYSIS of 117 occurrences of bumps in coal mines shows that 67.6 percent are associated with pillar-line points.4 Slabbing and splitting pillars, development, and other unfavorable milling practices in abutment areas may be a contributory or the primary cause of bumps. The cure for pillar-line bumps is to recognize areas that can be expected to become highly stressed and to project the mining plan and operations to eliminate such areas insofar as possible. If such areas cannot be eliminated, then the mining plan and operations should be projected to avoid the necessity of disturbing these areas before the stresses have been dissipated.

Jan 1, 1954

By Akshay Sakhuja, M. S. Karthika, R. Vignesh

"The bridge across River Mandovi in Goa is a cable stay bridge structure proposed parallel, along existing bridges for regulation and reduction of vehicular traffic; the entire bridge structure is supported on pile foundation socketed in rock. This paper describes drilling related issue encountered during execution of pile where bed rock varies considerably from factual geotechnical investigation, which in turn affected the productivity of bored piles socketed in rock then chiseling is advocated for rock socketing with limited number of blows based on penetration resistance of rock encountered or equivalent energy principle to increase the productivity and also to avoid excess chiseling which otherwise would have fractured the rock mass below and around the pile tip resulting in increased settlement of pile subjected to design load. Contractor decision on socket length have been taken without compromising either quality or productivity; the paper presents various procedures and the equipment involved for installation of pile in rock along with the conclusion related to termination of pile in rock and also the lessons learned in process.INTRODUCTIONPile foundations are generally used to transfer heavy loads in deeper bearing stratum if the soil immediately beneath the base of the foundation does not have sufficient capacity. The bridge across River Mandovi, Goa is in its construction phase as a part of the development plan of Goa State Infrastructure Development Corporation Ltd (GSIDC). The project was awarded to M/s. L&T Construction, Heavy Civil Infrastructure; subsequently the geotechnical investigation was awarded to M/s L&T Geostructures.The client has specified the foundation of the bridge as rock-socketed. Rock socketing is generally done to achieve higher bearing pressure through concrete-rock shear interface which many building codes permit. The design and construction of rock socketed pile foundation entails a detailed analysis and judgement on the superstructure loads, predominant geological conditions as well as ground water levels. The termination of pile is normally based on thumb rule of half to three times the pile diameter into the rock. Quite often the criteria is based on chisel penetration rate (Gandhi,1990) In fact, this is the key factor to consider appropriate and economical depth of embedment of pile into rock stratum which necessitates enormous understanding on the type and quality of rock strata encountered which may significantly influence the selection of suitable rotary rig for pile installation. Such criteria are site specific and also applicable for the set of equipment used for the particular project."

Jan 1, 2015

By Hwa-Soo Park, J. K. Yoon, Hoseok Nam

In a thin slab casting process, control of fluid flow in mold is particularly difficult due to the high casting speed and large aspect ratio of the mold and the understanding of the fluid flow motion as well as heat transfer in mold is regarded as the most important information because the melt delivery is directly related to the problems of shell growth nonuniformity, surface turbulence and mold powder entrapment. A mathematical model has been developed for the coupled analysis of fluid flow, heat transfer and solidification in funnel type mold using finite volume method based on a body fitted coordinate and the characteristics of the transport phenomena in the mold of thin slab caster were analyzed by numerical simulation. As a result of simulation, the basic flow pattern is characterized as four large recirculations and two small eddies near the narrow faces of mold, which is somewhat different from that of parallel type mold or other conventional slab caster. The heat transfer model accurately predicted the mold positions susceptible to cracking as a result of thermal stress and the predicted shell thickness shows good agreements with the measured shell thickness on breakout products. We also investigated the influences of some operation parameters such as casting speed, nozzle type, submerging depth and mold material on fluid flow, heat transfer and distribution of solidifying shell and various information for the determination of optimal operating conditions were obtained.

Jan 1, 2000

By J. D. Mooney, D. L. Darnell

The accompanying chart has been drawn for the convenicncc of engineers as' a means of quickly determining the correct number of plies of conveyor belts operating under specific conditions. The calculations are based on the average safe strength (factor of safety, 15) of the various standard rubber conveyor belts. The calculations assume maximum loading conditions; that is, the belt is considered as carrying the greatest load that it will handle without spillage at ordinary belt speeds. This not only produces the most economical operating conditions, but also the maximum tension in the belt. The chart is a graphical representation of the formula: Where, p = kg W(L + 10H) p = the correct number of plies k = a constant, depending on the type of drive g = the weight 'in pounds per cubic foot of material handled W = the width of the belt in inches L = the length of the belt in feet (approximately twice the center distance). H = the difference in elevation between the head and tail pulleys, in feet. For a simple drive, with a bare pulley, k = ----1 For a simple drive, with a rubber-lagged pulley, k = --- 1 For a, tandem drivej with bare pulleys, k = 1/375.000 For a tandem drive, with rubber-lagged pulleys, k = ---1 The chart is drawn for a simple drive, with a bare pulley (k — =e)1 ; therefore, the number of plies obtained from the chart should be multi- ' plied by the factor 0.83 or 5/6 for simple, lagged drive; the factor 0.67 or 2/3 for tandem, bare; and the factor 0.55 or 11/20, for tandem, lagged. The formula p = kgW(L + 10H) has been developed mathematically

Jan 1, 1916

By D. E. Shanks

The Bureau of Mines surveyed a variety of inorganic ion-exchange materials to determine their suitability for removing valuable accessory elements and troublesome contaminants from metallurgical process and waste streams. Most of the materials, which included molecular sieves, heteropolyacid salts, and hydrous metal oxides, did not give adequate separations, did not have the necessary stability in strong acids or bases, or were not in a physical form suitable for ion-exchange use. Many of the suitable inorganic materials, especially the hydrous oxides, were capable of cation exchange with high capacity only in basic conditions, which caused hydrolysis of most of the cations tested. Multivalent anions, such as arsenate and phosphate, were easily removed from acidic solutions by hydrous oxides. Hydrous zirconia was the best material for this purpose. Multivalent anions were not easily des orbed because of compound formation; therefore, conventional ion-exchange techniques could not be employed. As an alternative approach, hydrous ferric hydroxide was used as a filter material to remove arsenate and phosphate from acid solutions. One gram of arsenic was removed from solution for each 20 g of ferric hydroxide. Ferric hydroxide is preferable to hydrous zirconia for use as a filter material because of low cost.

Jan 1, 1983

By V. Rajaram

The Parachute Creek Member of the Green River Formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential. A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch Joint Venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 1, 1977

By D Horacek, I K. Sheppard

Ok Tedi is in a period of transition. By 2008 mill feed will consist of higher levels of high-grade but metallurgically challenging skarn ores. Additionally, the Taranaki pit will start production in 2008 along with the start-up of a new pyrite concentrator. Taranaki ores are very high in sulfur. Sulfur is captured in a pyrite concentrate prior to tailing entering the Ok Tedi River. These and other complex scheduling issues will need to be resolved over a critical three-year period. With these requirements in mind, Ok Tedi contracted AMC Consultants to develop a custom version of the Life of Business Optimisation System (LOBOS¬) to assist medium-term production scheduling at Ok Tedi. LOBOS utilities enable Ok Tedi planning engineers to:import polygon-based reserve data (Blast Masters) from MineSightÆs Interactive Planning Tools (IP Tools); graphically construct block sequencing and material flow constraints; edit constraints defining standard scheduling, processing and financial relationships; define dump and stockpile attributes; and assign capacities to production systems, plants, dumps and stockpiles. LOBOS converts Ok TediÆs production scenario into a mixed integer program (MIP) and submits the resulting model to IlogÆs Cplex MIP Solver. The Solver seeks an optimal production schedule that maximises net revenue per mill hour while meeting all constraints. This paper introduces Ok Tedi and its production requirements and relates these requirements to the facilities developed for an Ok Tedi version of LOBOS.

Jan 1, 2007

By Warren E. Morrison

A simplified energy model for the United States is quantified for a recent historical period. The basic model and calculated quantified structures are used for a number of analytical case studies that estimate midterm and long-range shifts in patterns of energy resources demand and required supply. Historical data series are presented for the years 1947 to 1965 in the form of integrated energy balances by source, form, and consuming sector. In case studies I to XII, conditional projections of historical trends of energy demand and required supply are made for the midterm period 1966 to 1980. The projections are carried out by correlation of major energy components with relevant independent variables such as major economic indicators. Simulations of the medium-range projections to 1980 are carried out by varying the assumptions for the determining variables to produce high-and low-range projections for the midterm period. Case studies XIII to XXII are long term contingency or technological forecasts to the year 2000. These cases assume technological changes or innovations that produce major shifts in the long term pattern of energy consumption and the mix of required resources. The domestic resource base is assessed in its ability to meet projected or forecast demand for energy resources under the midterm and longrun assumptions made in the various case studies. Various energy issues or problems identified from the analyses of the case studies are discussed, and possible alternative approaches to solutions to these issues or problems are suggested.

Jan 1, 1968

By B Shi, Y Li, L Ma, F Zhou

Subsurface fires are a common threat to coal mining, as spontaneous combustion of coal can potentially result in gas combustion and explosion. Fire-proof techniques, such as grouting, foam, or colloid injection, are not in a position to function ideally, due to the limited coverage and stopping the extinguishment substance from reaching the fire location. Liquid nitrogen, as a kind of all-submerged fire prevention or extinguishing method, can rapidly extinguish fires, thus preventing gas explosion and minimising extinguishment time. Injecting liquid nitrogen through boreholes is an important way during the period of mine catastrophe. But liquid nitrogen is not effective enough in infusion; technical issues restrict the development and utilisation of liquid nitrogen fire prevention and extinguishing technology. Immediate infusion of liquid nitrogen is usually associated with ‘air slug’ (the balloons and bubbles in the pipeline which hinder the flow of low-temperature liquid), which blocks pipelines for liquid nitrogen injecting. Another issue is that the pipeline tends to be damaged due to freezing, which undermines the injecting efficiency of liquid nitrogen and its application result. In order to solve the problems of the low efficiency and some other related field issues in liquid nitrogen perfusion, the ground–underground high efficiency liquid nitrogen injection technology were developed. Implementation of liquid nitrogen infusion techniques in Chinese coalmines achieved the goals of fire prevention and air-cooling. The technique presented in this paper is efficient in absorbing heat, and consequently, displacing oxygen and combustible gases. Field tests at Rujigou and Yangchangwan Coalmine justified the efficiency of the technique. By using this technique, there was no waste left behind, which may impede the subsequent production. The presented technique is of great benefit to the social, economic, and environmental aspects of mining operations, and will have broad applications in fire prevention for large-scale coalmines.CITATION:Zhou, F, Shi, B, Li, Y and Ma, L, 2015. Key techniques and engineering applications of stereoscopic liquid nitrogen infusion for coalmine fire prevention, in Proceedings The Australian Mine Ventilation Conference, pp 291–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Jing Chai

The Cenozoic unconsolidated strata with the thickness of 100 to 240m in the east area of China are composed of clay, sandy clay and hardpan, etc. Numerous shafts of the coal mines in these areas have been damaged to various degrees since 1987, with the main reason for this being the subsidence of the super-thick unconsolidated strata. To prevent the continuing settlement deformation of unconsolidated strata caused by groundwater removal, long-term water injection through multiple boreholes controlled the settlement deformation of unconsolidated strata. A new type of fiber Bragg grating (FBG) sensing system was successfully used for real-time strain monitoring of the unconsolidated strata during water injection at a coal mine in China. A mathematical model for the compression settlement induced strain calculation is proposed which can assist understanding of the effect of water injection on the ground. With the increase in water injection, the unconsolidated strata compressed state was improved by the transition of the stress state from compressive to tensile stress. The wavelength change of fiber Bragg grating sensors corresponded with the trend of the water level in the same strata. Engineering practice indicates that these sensors can normally, safely and reliably survive conditions associated with hydrous unconsolidated strata. The FBG sensing can be used for continuous lifetime monitoring of the system, starting with real-time monitoring during low-pressure water injection process of multi-borehole. The results will give important guidance for water injection and mastering stratum subsidence.

Aug 1, 2013

By M. A. Perras, M. S. Diederichs

"The Niagara Tunnel Project (NTP) is a 10.1 km long water-diversion tunnel in Niagara Falls, Ontario, which was excavated by a 14.4 m diameter tunnel boring machine. The excavated rock types included limestone, sandstone, siltstone, shale and mudstone. Based on observations and measurements the overbreak was divided into four zones. Approximately half the tunnel length was excavated through the Queenston Formation, which locally is a shale to mudstone. Three of the four overbreak zones were within the Queenston. Zone 1 includes the formations above the Queenston Formation, Zones 2 and 4 are border regimes with little or no influence from St. Davids Buried Gorge and Zone 3 is the area influenced by the gorge. Zones 2 through 4 can be generally summarized as having overbreak as the result of stress induced spalling. Zone 2 marks the transition from slabbing at the Whirlpool contact in the stress shadow to spalling towards Zone 3. The behaviour of Zone 3 is interrupted from the typical high stress behaviour due to the presence of St. Davids Buried Gorge. As the tunnel passed from the gorge the high regional stresses induce spalling, which creates the typical notch shaped overbreak geometry of Zone 4.Three modelling approaches were used to back analyze the brittle failure process at the NTP: damage initiation and spalling limit, laminated anisotropy modelling, and ubiquitous joint approaches. Analyses were conducted for three tunnel chainages: 3+000, 3+250, and 3+500 m because the overbreak depth increased from 2 to 4 m. All approaches produced similar overbreak geometries to those measured. The laminated anisotropy modelling approach was able to produce overbreak depths and chord closures closest to those measured, using a joint normal to shear stiffness ratio between 1 and 2. The back analysis results were able to produce sets of stress and strength inputs for different sections of the tunnel at the transition from overbreak Zone 3 to 4. The back analysis procedure demonstrates the importance of including the anisotropic stiffness in the numerical modelling approach to correctly capture the overbreak geometry and deformations around underground excavations."

Jan 1, 2015

"Geometallurgy is a discipline that seeks to improve the sustainability of the extraction of metals and minerals by promoting the smarter use of non-renewable resources, better energy efficiency and greater use of renewable energy. To achieve these goals, development of innovative technologies and approaches are being developed along the entire commodity value chain, starting with exploration and extraction and extending to reuse and recycling. This paper discusses the geometallurgy of industrial minerals with special emphasis on kaolin, a versatile industrial mineral applied in ceramics, paper, paint, plastics, rubber, pharmaceuticals, cosmetics, ink, sealants, adhesives, sanitary ware, glass fibre, toothpaste, animal feed etc. Aspects of kaolin extraction in south-west UK are analysed from a geometallurgical perspective. While geometallurgy already features in kaolin extraction, its role can be significantly expanded by combining advanced in-pit characterisation and orebody modelling with integrated planning and control of the refining and calcination process. This paper highlights the importance of innovation in realising the full potential of geometallurgy.CITATION:Glass, H J, 2016. Geometallurgy – Driving Innovation in the Mining Value Chain, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 21–28 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By D P. Murphy, R F. Dewhirst

Traditionally closure has been seen by the Resource sector solely as a green or an environmental issue, focused primarily on the requirement to rehabilitate the site following cessation of production activities. In addition to operational, maintenance and production aspects of processing plant design, future design teams will need to take a more holistic view and consider an increasing number of sustainability issues including safety in design and cleaner production as well as closure itself. Sustainability principles being adopted by industry such as the Minerals Council of AustraliaÆs Enduring Value Framework are now broadening our understanding of closure. While issues around the closure of tailings dams and associated infrastructure have been widely studied, few investigations have looked closely at the implications of closure on the design of minerals processing plants. It is likely that design teams may be able to make a significant contribution to meeting industry objectives by adopting innovative designs which, in addition to meeting production objectives, deliver sustainable and cost effective plant closure outcomes. This presentation explores the opportunity for innovative design of mineral processing plants through the assessment of alternative closure objectives. This assessment specifically looks at current industry standards and statutory requirements, as well as potential risks and opportunities associated with each objective. Alternative design strategies to meet these objectives are discussed.

Jan 1, 2006

By Matt Bilson, Ritesh Mahajan, Antoni Kuras, Wataru Okada

The Waterview Tunnel comprises twin 2.4 km long 13.1 m internal diameter three lane road tunnels in Auckland, New Zealand. The City Rail Link (CRL) is a 3.45 km long, 6.24 m internal diameter twin rail tunnel underneath Auckland’s city center. This paper presents an overview of the tunnel geometry, segmental lining congurations, geometric constraints, performance criteria and functional reuirements for the large diameter Waterview Tunnels and smaller diameter CRL tunnels. Other key aspects, which include sustainability, innovations, construction performance and practical aspects are discussed and compared. Lessons learnt from these mega tunnelling projects are also presented.

Jun 23, 2024

By N. S. Dalal, X. Shi, V. Vallyathan

"Electron spin resonance (ESR) and cytotoxicity measurements were made on newly fractured silica to examine specifically the role of the fractured-induced, siliconbased radicals (Si· and SiO·), and silica-generated hydroxyl (·OH) radicals in the mechanism of the cell membrane damage by silica. The concentration of the Si· and SiO· radicals was controlled through decay processes, thermal annealing, and boiling, while that of the ·OH radicals was varied by using catalase, superoxide dismutase, KMnO4, Ha2seO3, ascorbic acid, and metal ions, and monitored via ESR spectroscopy. The dust's cytotozicity potential was evaluated by measuring the silica-induced hemolysis and also by determining lipid peroxidation (using linoleic acid). Prom the comparison of hemolysis and ESR results it is deduced that the radicals play little· or no role in the silica-induced hemolysis. However, the lipid peroxidation data indicate that the radicals might be involved in the initiation of an oxidative chain reaction leading to the macrophage membrane damage through lipid peroxidation. INTRODUCTIONThe biochemical mechanism of Quartz-related pneumoconiosis is still not fully understood. It is believed, nevertheless, that one event of primary importance is the perturbation of cell membranes by the dust particles (Allison et al., 1966; Allison and Harrow, 1971; Bateman et al., 1982; Parazzi, et al., 1968; Reiser and Last, 1979; Shi et al., 1989; Summerton et al., 1977). The ensuing cell-membrane damage unleashes certain lytic enzymes resulting in additional cell injury and eventual fibrosis (Nolan et al., 1981; Summerton et al., 1977). Thus considerable effort is currently being made towards the understanding of the processes by which quartz particles disrupt the membrane of a red blood cell (RBC) or a pulmonary alveolar macrophage (PAM). A simple but important method of evaluating the membrane damage potential of a dust is the hemolysis test (Harington et al., 1971). Even though this test is used routinely for screening dusts for their cytotoxicity potential, the biochemical mechanism underlying the cell lysis by many dusts, including quartz, is still controversial (Kilroe-Smith, 1974; Singh and Rahman, 1987), and this provided us the impetus for the present undertaking."

Jan 1, 1989

By J. R. Linney

THE Eastern Magnetite Industry produced approximately 7,850,000 long tons of crude ore in 1945 from which was obtained approximately 3,650,000 long tons of shipping product or a ratio of 2.10 to 1. Lack of skilled or experienced miners was the greatest handicap. Veterans returning to work improved the underground labor shortage in some localities but as a whole the labor shortage was keenly felt throughout the industry. One cannot now predict what may be accomplished in 1946 but barring major steel strikes a worthwhile improvement can be expected. At the Richard mine of the Richard Ore Co., the shipping product for the year amounted to approximately 124,650 long tons of concentrate and lump ore. Crude-ore production was 160,600 long tons. The average analysis for lump ore was 63 per cent iron and for concentrates 66.05 per cent. The Warren Foundry and Pipe Corp. at their Mt. Hope mine produced 73,000 long tons of lump ore averaging 59.5 per cent and 57,000 long tons of concentrate averaging 67 per cent. The total mine hoist was approximately 209,000 long tons. Operations were commenced through the new Leonard shaft on Jan. 18; the Brown shaft through which operations had been conducted since 1912 caved beyond repair on Sept. 26. No one was injured but pumping facilities were somewhat disrupted. In order to reach designed capacity a total of 400 men will be required with 300 underground. Due to shortage of labor all operations in 1945 were concentrated on the 1700 level. As fast as men can be hired and trained development of the 2100 and 2500 levels will commence. Mt. Hope has a consider-

Jan 1, 1946