Search Documents

By C. Liu, G. Zhu, Y. Liao

"The effect of particle size on the flotation kinetics of a low-rank coal was compared using air bubbles and oily bubbles. Five kinetic models were applied to the data from the tests to derive the relationships between the flotation rate constant, the ultimate recovery, and the particle size fraction. The results show that oily bubble flotation (OBF) resulted in a lower ash content and higher combustible recovery than air bubble flotation (ABF), especially for the -125 ??m size fraction. It was found that the flotation of a low-rank coal in individual size fractions using air bubbles and oily bubbles can be best described by a first-order model with rectangular distribution of tendency to float and the classical first-order model respectively. OBF yielded higher ultimate combustible and ultimate ash recoveries. The flotation rate constants for OBF were higher in all the models except for the fully mixed reactor model. The ultimate recovery values and modified rate constants first increased and then decreased as the size fraction decreased. The trend of the flotation rate constants as a function of the size fraction was similar in all the models except for the fully mixed reactor model. IntroductionFroth flotation is a physical-chemical separation method that is widely used in coal beneficiation for the separation of fine coal particles from associated minerals in water slurries. Since the cumulative recovery of a component in the concentrate is proportional to flotation time, the flotation process can be considered as a time-rate recovery process (Emad, Mohammad, and Bahram, 2010). Therefore, the general mathematical flotation models that incorporate both a recovery and a rate function can describe flotation time recovery profiles.The kinetics of coal flotation, as a measure of coal recovery as a function of time, have been studied in detail by many researchers. Different kinetic models have been proposed and published in the literature. The order and the rate constant are strongly dependent on the flotation conditions, such as the particle size and size distribution, the bubble concentration, the reagent concentrations, and the operating parameters (Zhang et al., 2013). The particle size has been reported to affect the flotation kinetics to a great extent (Yoon, Luttrell, and Asmatulu, 2002; Ntengwe and Witika, 2011). Numerous researchers have studied the aspects of flotation kinetics while paying special attention to particle size (Meftuni and Ibrahim, 1997; Rubinstein and Samygin, 1998; Graeme, 2012). However, the effect of particle size on the flotation kinetics of a low-rank coal has been relatively little discussed."

Jan 1, 2017

By G C. Bolton

Experiments were conducted to access the feasibility of removing zinc from lead slag by sulfation or chlorination or both. Gaseous sulfation with sulfur dioxide and oxygen released only 50 per cent of zinc even under the most severe conditions. Sulfation with concentrated sulfuric acid by a fast-leach process released 95 per cent of zinc while pug-roasting released a maximum of 78 per cent of zinc. Chloridization with NaCl in the presence of sulfating gas released 50 per cent of zinc, while direct chlorination with chlorine gas and oxygen released 85 per cent of zinc and 100 per cent of lead in a chloride condensate containing little impurities.

Jan 1, 1980

By Jacob Chacko

The Izmit Bay bridge, a 3-km-long suspension bridge crossing of Izmit Bay, Turkey is planned to be constructed in one of the most seismically active places in the world. The site, which has the potential to experience significant earthquakes associated with the relative motion accommodated on the North Anatolian Fault, is underlain by deep deposits of soft soils, and areas of unstable and liquefiable soils. Characterizing the seismotectonic setting, foundation soil conditions, potential fault locations, as well as other geohazards was a critical component for the project concessionaire to finance the project and obtain meaningful bids for bridge design and construction. Given the Build Operate Transfer (BOT) funding mechanism, executing this work in the least possible time was critical to the concessionaire?s financing scheme. Fugro was retained to provide geotechnical, geological, and seismological evaluations for the project region, and to generate data for contractors to develop reliable designs and bids. The uncertainties in these data made it difficult for the BOT concessionaire to finance the project and tender Bridge design and construction. The investment in an early and comprehensive site characterization program to evaluate and quantify those uncertainties allowed the concessionaire to save schedule, provide a robust bid basis to bridge contractors, and persuade banks to finance what was perceived to be a relatively high risk project.

Jan 1, 2011

By R. D. Eash

The purpose of this research contract was to develop and test a Saran latex modified portland cement concrete lagging to be used as a replacement for wood lagging. The scope of work performed was divided into four phases: Phase I - Engineering Criteria; Phase-! I1 - Design Study; Phase III - Fabrication of Lagging; and Phase IV - Prototype Demonstration Project. Each phase of work was completed and is described in detail in this report. The prototype latex modified concrete lagging developed in this program weighed 52 pounds. When tested in flexure, it supported center point loading of 4500 pounds and under 1/4 point loading it supported loadings of 7000 pounds. Deflections at maximum loading ranged from 1/2 to 1 inch. Maximum deflections exceed 2 inches. The lagging does not exhibit catastrophic failure. Two hundred and twenty of the LMC lagging were produced and shipped to the Bunker Hill Company in Kellogg, Idaho for installation in their mine at the 17 level. The lagging are performing satisfactory after 22 months exposure in the mine.

Jan 1, 1980

By Robert F. Mehl

PROGRESS in the general field of nonferrous physical metallurgy during the past .year has been uneventful but healthy. A continued increase is apparent in the number of useful alloys and in the mechanical treatment and heat- treatment of finished metals and alloys nothing can hinder the multiplication of alloys or the diversification of their treatment as knowledge of the behavior of .alloys increases; as ternary and quaternary alloys are better understood, hundreds of new metal combinations with unusual properties may well be expected. Evidence of rapid progress is already at hand.

Jan 1, 1936

By Thomas B. Dellinger

Since 1950, rotary-drilled, large-diameter holes, "big holes", with depths to over 300 feet and diameters of over 30 inches have become numerous and widespread. Fifty such holes have been drilled for access shafts to LPG mined caverns, Over 70 holes have been drilled for various other commercial activities. Over 150 holes have been drilled by the AEC for atomic testing purposes. These holes have ranged up to 300-inch diameters with 1600-foot depths, 120-inch diameters with 570-foot depths, and 72-inch diameters with 4800-foot depths. Equipment is now available to drill a wide range of ?big holes? for varied requirements. At least a dozen drilling contractors are participating or have participated in the drilling of "big holes". The accompanying tables show pertinent historical, technical and economic data on over 250 holes. The illustrations to be presented concurrently with this paper show the various equipment and accessories now in use. (See Appendix I for captions of illustrations.)

Jan 1, 1966

By R. E. Ogilvie, N. L. Peterson

Diffi-lsion measurements were conducted at all compositims in the bcc solid solution of the U-Nb system employing incremental couples at composition intemals of 10 at. pct. Diffusion coefficients were determined by the Matano method from concentration gradients obtained with the electron-probe microanalyzer. The activation energy for inter-diffi-lsion as a function of compositim shows three distinct regions: 1) 80 to 100 pct U.6= 30 kcal per mole; 2) 20 to 80 pct U, $ - 70 kcal per mole; 3) Oto 20 pet U, Q = i40 kcal per mole. The frequency factor, fi0 and the activation energy $ were found to be roughly related by the following equation: log Do ^9.7 X IO-5Q -6,6. The Kirkendall marker movement indicates that DU is larger than DNb between 16 and 100 pct U and DNb is larger than DU from 0 to 4 pct U. FOR practical as well as fundamental reasons, the rates of diffusion in alloys are of considerable consequence. Most solid-state reactions are largely dependent upon the diffusion of atoms through the lattice structure and along grain boundaries. The high-temperature strength and reasonable nuclear properties of niobium have prompted its use as a reactor material in contact with uranium fuel. Hence, diffusion data for the U-Nb system are of considerable importance. In the previous diffusion study1 on the U-Nb system using pure element couples, reliable data were obtained only in the range of 0 to 10 at. pct Nb due to the large variance of the diffusion coefficient with composition. Also, a large Kirkendall effect and considerable porosity in the uranium-rich areas of the specimen were reported, which suggests that the true diffusion coefficients are somewhat larger. The purpose of the present study was to obtain reliable diffusion coefficients at all compositions using incremental diffusion couples with intervals of 10 at. pct. In view of the abnormal self-diffusion be- havior of y uranium2-4 and some other bcc transition elements,&apos;-&apos; it was felt that a comparison of the interdiffusion coefficients in the bcc U-Nb system with those of Reynolds et al.9 for the fcc gold-nickel system might shed some light on the diffusion mechanism involved. Both systems have similar phase diagrams, in that complete solid solubility exists above a miscibility gap. EXPERIMENTAL PROCEDURE The uranium used in this investigation was obtained through the courtesy of Argonne National Laboratory. An analysis of this material detected only Si-30, A1-7, C-6, N < 10 and 0-18 ppm. The niobium was electron-beam melted material obtained from Stauffer-Temescal. The gaseous impurities were less than 50 ppm, and the spec troc hemical analysis showed Ta-500 and W-200 ppm. U-Nb alloys were prepared at composition intervals of 10 at. pct by melting the appropriate amounts of the pure elements in an arc furnace. The buttons were inverted and remelted 6 times to assure complete mixing. The buttons were then wrapped in molybdenum foil, canned in Zircaloy-2 or stainless steel, and hot rolled 30 pct reduction in thickness at temperatures between 850" and 1100°C. Alloys with 10, 20, 30, 40, and 90 at. pct Nb rolled quite easily under these conditions, but the 50, 60, 70, and 80 pct alloys remained brittle. After melting and rolling (when possible), the alloys were annealed for 24 hr at a temperature within 100°C of their melting point in a dynamic vacuum of better than 4 x 10-8 mm Hg. These treatments produced alloys which were homogeneous on a 1 p scale within the detectability limits of the electron probe. During fabrication, the alloys picked up as much as 100 ppm Mo and 100 ppm Zr. Other elements checked for but not found were Co, Cr, Fe, Mn, Ni, and Ti. The grain size of the annealed samples ranged from 3 mm for the uranium-rich alloys to 0.3 mm for the niobium-rich alloys. This permitted measurements of the concentration gradients in the diffusion samples without crossing more than one or two grains, thereby eliminating any grain boundary effects. The specimens were bonded by theU&apos;picture frame" technique as reported by Kittel.10 Specimens of composition b)U + (100 - x)Nb were sandwiched between two specimens of composition (x + 10)U + (90 - x)Nb after they were ground flat and parallel

Jan 1, 1963

By Louis A. Panek

An improved centrifugal-testing apparatus has been designed and built in the Bureau of Mines laboratory at College Park, Md., which is unique in that it incorporates the use of resistance gages to measure directly the strains in a rotating model without testing it to failure. Owing to this feature, a more rapid testing method can be used; furthermore, model materials need not be restricted to those of the prototype. The behavior of any structure in which strains of significant magnitude are produced by its own weight may be studied in a small model subjected to simulated gravity loading. The model is rotated in a centrifuge to induce in it centrifugal forces, which, like the gravitational forces in the full-size structure, act on the volume elements and are proportional to the masses thereof. Centrifugal testing is, therefore, applicable to the design of mine openings and to the study of similar ground-control problems. It constitutes an experimental method for determining the state of strain in a structure for which analytical methods are excessively laborious or even impossible. In previous applications of centrifugal testing by other investigators, the models usually were tested to failure, and the analysis was made from-the type of break produced. The models were made of the same materials as the proto-type, and the test results were applied only to the particular prototype represented by the model. Beam deflections were measured from photographs of the rotating model, but no means was employed either to determine the actual distribution of stress in the model or to determine quantitatively the degree of restraint imposed on the ends of the loaded model beam, that is, to determine whether the loaded model behaved as a beam with rigidly fixed ends or as some other type of beam. With the apparatus described, it is possible to determine the state of strain, and thus the boundary conditions, in a rotating test model weighing up to 90 lb., which can be subjected to centrifugal forces up to about 2,600 times the force of gravity. The load-strain relationship, applicable directly to the prototype, can be determined from a Single model test. The test results can be presented as quantitative relations between the loads, strains, and dimensions and mechanical proper-ties of the structural members and can be applied to any prototype, whatever its component materials, that satisfies the similarity requirements.

Jan 1, 1952

By Albert Sauveur

Jan 1, 1924

By Albert Sauveur

Jan 1, 1924

By F Faraj, M Pal, M Haest, M Bradshaw, H Lang, K Hume

MineSense Technologies Ltd. is revolutionising grade control at mining operations by installing ShovelSense® sensors on buckets that measure the grade of every load before it is dumped in the truck. This allows the mine to exploit grade variations at a resolution that was not available before, reducing the amount of ore loss to the waste stream and removing waste from material destined for processing. These changes dramatically improve the profitability and sustainability of mining operations. ShovelSense relies on X-ray fluorescence analysis of the rocks as they flow in the bucket and is integrated with fleet management to direct the trucks to the right destination. Lab simulations of ShovelSense measurements on porphyry copper ores show correlations between predictions and lab measurements at 0.98 r-squared with a coefficient of variation of 10 per cent. Visualisation of copper grade predictions in three dimensions shows a reasonable match with the dig plan, but with local changes in the ore-waste contact due to more accurate contact identification, related to blast movement and other mining factors. Correct delineation of these contacts ensures ore trucks are not sent to the waste dump and waste trucks are diverted from the crusher, creating enormous value for the operation and the environment.

Mar 22, 2022

By A. P. Williams

"This paper presents an overview of plant electrical systems in general, a discussion of the problems that may occur due to plant growth, the maintenance required to maintain the reliability and safety of the electrical system, and the selectivity of the relay protection system. It is divided into two main areas: short circuit levels within the plant electrical system; and relay protection systems.This information is directed at maintenance supervisors, mine managers and electrical superintendents who have been away from detailed short circuit and relay coordination calculations for some time. It points out the potential problem areas within an operating plant electrical system. Short Circuit LevelsTheoryThe electrical equipment in a plant such as breakers, switches and starters has two short circuit ratings, the momentary rating and the interrupting rating. These ratings may be given in MVA or current (amperes) depending on the equipment and manufacturer&apos;s preference. Since for a three-phase system MVA and amperes are related by the formula"

Jan 1, 1987

By Cao rong-jiang, Tang Xin-he

"In ordinary manufacture process of tungsten powder, a preferable intermediate product used is ammonium paratungstate (APT). The particle size of tungten powder made from it through W2OO58 is larger than 1. 0 um. In order to obtain ultrafine tungsten powder with narrow size distribution, a new type of tungstate, hydraziniull tungstate, was studied. Its formula is 5(N2H5)2O·12 WO.s , with tetragonal crystal structure of a=5.821 , c=18. 468. Three methods for preparing hydrazinium tungstate (ART) were set up and ART can be produced by current industrial APT process with little modification of operation and without any change of equipment.Under certain PH and operation condition of the solution from which ART was produced, an autoreduction of tungsten occured, which produced a lower valency tungstate with blue color when ART was heated at different temperatures, in N atmosphere, tungsten bronze, tetragonal W0290 and W02.7E could be obtained respectively. They all have the superiorities, in the production of tungsten powder, of superfine size and narrow size distribution [average size of 0.5um or even smaller.The rate of autoreduction of ART is very fast at elevated temperature. The reduction reaction, which gaves tetragonal WO290, could be handled smoothly without explosion. To research their behaviors at autoreduction temperatures and the products of autoreduction will be new advances of tungsten chemistry and may also serve tungsten industry with new processes and materials."

Jan 1, 1988

By R Strand, L Reading, G Keir

A major challenge in managing coal seam gas (CSG) water is predicting how much water will be produced as the industry develops. Klohn Crippen Berger Ltd (KCB) was commissioned by the Queensland Department of Natural Resources and Mines (DNRM) to develop a tool to forecast where, when and how much CSG water will be produced in the Surat and Southern Bowen Basins under various industry expansion scenarios.The water production tool (WPT) uses the Theis equation, a non-equilibrium groundwater flow equation that accounts for the effect of pumping time on well yield in confined aquifers, to predict water production volumes. Where multiple pumping wells are in close proximity, the required pumping rates for coal seam depressurisation are reduced. Therefore, pumping effects are projected spatially to assess interference effects between wells. Water production is then upscaled to the projected scale of the CSG industry within the Surat and Southern Bowen Basins.Two modifications were made to address the dual phase nature of CSG extraction (a transmissivity reduction factor) and the impact of weathering at the eastern margin of the Surat Basin (a ænear edge effectÆ factor). These factors modify relevant hydrogeological parameters in a consistent and defensible manner to more closely match observed water production.The WPT was verified by comparing results to equivalent Theis equation calculations and to type curves provided by CSG proponents. Calibration was achieved by varying the spatial distribution and intensity of the near edge effect factor in conjunction with a chi-squared analysis of residuals.The tool, which is now being maintained and further developed by the Centre for Water in the Minerals Industry (CWiMI), was built to balance numerical complexity against relative flexibility and simulation speed. The result is a tool that can produce statistically relevant results of prescribed scenarios to plan water handling and treatment requirements in discrete zones of operation.CITATION:Strand, R, Reading, L and Keir, G, 2013. Water production simulation tool for coal seam gas operations in Bowen and Surat basins, in Proceedings Water in Mining 2013 , pp 311-320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Michael Gauna, Christopher Mark

"Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. Despite decades of research, the sources and mechanics of these events are not well understood, and therefore they are difficult to predict and control. Experience has shown, however, that certain geologic and mining factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present, and then identifying appropriate control measures to mitigate the hazard. This paper summarizes the U.S. and international experience with coal bursts, and describes the known risk factors in detail. It includes a framework that can be used to guide the risk assessment process.BACKGROUNDCoal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. During the years 2012-2014, serious coal bursts occurred at three different U.S. room and pillar mines. These events resulted in three fatalities and two permanently disabling injuries (MSHA, 2014; MSHA, 2013). In all three instances, the events occurred during pillar recovery at depths exceeding 1,000 feet (300 m). None of these three mines had previously reported a burst to MSHA. Coal bursts also occurred at three longwall mines during this same time period.Despite decades of research, the sources and mechanics of bursts are not well understood, and therefore these events are difficult to predict and control. Experience has shown, however, that certain risk factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present. In addition, some control techniques are effective in reducing the likelihood of an event or protecting miners from their effects."

Jan 1, 2015

By Amr Sallam, Ahmad Mohamed, Mohamed Alrowaimi

Renewable energy, in the form of wind and solar, has emerged as main source of energy in the modern society. The wind industry has substantially grown over the last two decades to become a key player in providing energy to public. Wind turbines are getting larger, taller, and more efficient every year. The foundation is a major component of the wind turbine system. The wind turbine foundation must provide short and long-term stability for the overall turbine to allow continuous and safe turbine operation for energy production. The turbine serviceability and stability requirements must be geotechnically and structurally satisfied. In North America, major foundation types currently utilized in the wind industry include gravity spread foundation, mono pier foundation, and pile foundation. In this case study, a Post Tensioned Pile Cap (PTPC) foundation was used to support a 3.15-3.4 Megawatt turbine with 125M Rotor supported on 87.5M-hub-height tower. Soil anchors in the form of Auger-Pressure-Grouted-Displacement (APGD) piles and Continuous Flight Auger (CFA) piles were utilized. Four distinct subsoil conditions were identified, and for which four pile designs were adapted. Due to the occasional encounter of stronger soils at 50 to 55 feet (15.2 to 16.7 m), shorter pile design was preferred. To satisfy the design uplift load, pile post grouting were utilized to increase the shaft capacity of the piles. In this paper, the pre-production pile load test program will be described. The pile load test procedure, analysis, and results will be presented. A discussion will be provided, which led to the selection of the optimum pile design to support the high tension loads taking into consideration pile length limitations.

By E. J. Roberts

F. C. Bond (Allis-Chalmers Mfg. Corp., Milwaukee) —This paper considers comminution as a first order process, with the reduction rate depending directly upon the amount of oversize material present. The data show that other factors should be taken into account, and it is possible that in time these may be evaluated as simultaneous or consecutive reactions: Development of the theory of comminution has been retarded for many years by the assumption that surface area measurements constitute the sine qua non of the work done in crushing and grinding, and it is encouraging to note the belated growth of other ideas. In the Abstract the term "net power" should be changed to "net energy." Throughout the paper the term "hp per ton" should be changed to "hp hrs per ton", or "hp hr t." The term "Probability Theory" in the title does not seem appropriate, since it is not clear how the probability theory is used in developing the ideas in the paper. There seems to be a contradiction between the large calculated advantages of closed circuit operation and the statement following that the closed circuit test results showed no significant change in grinding behavior, when compared with the batch grind curves. Tables I and II show that between 75 pct and 50 pct solids the energy input required decreases with increasing moisture content and may indicate the advisability of grinding at higher dilutions in certain cases. The calculation of the hp-hr per ton factor indicates an input in the laboratory mill of only 7.32 gross hp per ton of balls; this casts some doubt upon the accuracy of the factor used, since the power input in commercial mills at 80 pct critical speed is customarily much higher. The tests show that within fairly wide limits the amount of ore in the laboratory mill may be varied and a product of constant fineness obtained, provided that the grinding time is varied in the same proportion. This has often been assumed, and confirmation by actual testing is of value. The Cavg corrections for differences between the plant and laboratory size distributions do not seem very satisfactory, since in many cases the plant/laboratory ratio is farther from unity after correction than before. The following equation has been derived from the data in Table VI: Relative Energy (log new ball diam in in. + 0.410) Input = --------------—--------------- from which the relative energy inputs for balls of different sizes can be calculated and compared. The relative energy input is unity for balls of 2.715 in. diam. The equation indicates that the work accomplished by a ton of grinding balls per unit of energy input is roughly proportional to the square root of the total ball surface area; provided, of course, that the balls are sufficiently large to break the material. The data in support of this statement are admittedly meager, but are fairly consistent when plotted. The relative grindability values listed in Table VI for 200 mesh multiplied by 4/5 apparently correspond approximately to the A-C grindability at 200 mesh.&apos; It would seem that for open circuit tests comparable accuracy could be obtained much more simply by the old method&apos; of plotting the test grind, extending the mesh grinds to the left of zero time if necessary, and determining from the plot the equivalent time required to grind from the plant feed size to the plant product size, using the average of several mesh sizes. The en- ergy input value of one time interval could be determined by tests on materials of known grinding resistance, and this multiplied by the interval required should give the desired energy input value. The relative grindabilities would be the relative time intervals required for a specified feed and product size. When the plotted mesh size lines of a homogeneous material are extended to the left beyond zero time they meet at one point at zero pct passing. The horizontal distance of this point from zero time indicates the equivalent energy input required to prepare the mill feed. The author&apos;s results show that the closed circuit grinding tests give about the same K values as open circuit tests, from which he concludes that open circuit tests are satisfactory in many cases. The value of the closed circuit test is its ability accurately to predict energy requirements in closed circuit grinding for both homogeneous and heterogeneous materials. If the material is homogeneous, the open circuit test gives satisfactory results; but if the material contains appreciable fractions of hard and soft grinding ore, the open circuit tests will not be accurate because of the accumulation of hard grinding material in the circulating load. Since in most cases it is not possible to determine a priori whether the material contains hard and soft fractions, the closed circuit tests are preferable and more reliable. B. S. Crocker (Lake Shore Mines, Ontario)—Dr. Roberts probability theory of grinding is very similar to our log pct reduced vs. log tonnage method of plotting and evaluating grinding tests at Lake Shore. However, although we both seem to start at the same point we finish with different end results. Shortly after publishing our grinding paper (referred to by Dr. Roberts) in 1939, we did pursue the subject of the "constant pct reduction in the pct +28 micron material for each constant interval of time. We ran innumerable tonnage tests on the plant ball mills, rod mills, tube mills with 11/4 and 3/4 balls, and lastly pebble mills, with tonnage variations from 180 tons per day to 950 tons per day. We found that when we plotted the log of the tonnage against the log of the pct reduced of any reliable mesh, we had a straight line up until 90 pct of the mesh is reduced. We have also tested this in our 12-in. laboratory mill with the same results. We have used this method of evaluating grinds for the past 8 years and developed the recent four stage pebble plant on this basis. By pct reduced we mean the percentage of any given mesh that is reduced in one pass through a mill at a given tonnage (or time). For example, if the feed to a rod mill is 90 pct +35 mesh and the discharge at 500 tons per day is 54 pct +35, the pct reduced is 90 — 54/90 = 40 pct. If the feed had been 80 pct +35 the discharge would have been 48 pct +35 or pct re- duced 80-48/80 = 40 pct as long as the tonnage re- mained constant at 500 tons per day. Thus we can easily correct for normal variation of mill feeds. This log — log relationship derived from the tonnage tests of all our operating mills has proved of tremendous help in checking laboratory work and in designing alternate layouts or new plants. The difference between the log — log and the semi-log plot is only shown up when the extremes in tonnages are plotted. When the relationship between the pct reduced and the tonnage was first investigated, we used semilog

Jan 1, 1952

By R. A. King, B. G. Hunt, C. E. T. White

"This paper reviews the history, occurrence, properties, and uses of indium, and describes the commercial production and fabrication of that metal by The Consolidated Mining and Smelting Company of Canada, Limited (Cominco), at Trail, B.C'. Indium is produced commercially at Trail from dross retreatment furnace D.R.F.) slag, a complex by-product of the lead smelting operations. Furnace feed prepared from this slag is smelted with coke and limerock in an electric furnace. The e1ectric furnace bullion is parted electrolytically, producing a market-able lead-tin alloy containing about 8 per cent tin, and leaving the indium in the anode slime. Recovery of indium from the anode slime involves roasting the slime with sulphuric acid, followed by leaching with water, purifying the leach solution, recovering the indium by sponging with zinc or aluminum, and re-fining electrolytically. This process yields standard grade (99.97+ per cent) indium which is either sold or refined •to high purity ( 99.999 per cent) indium for special uses requiring higher purity metal."

Jan 1, 1959

By C. Riveros, H. Henein

Bulk Metallic Glasses have a high potential as advanced engineering materials due to their various properties including strength and corrosion resistance, to name a few. This paper investigates amorphous phase formation and rapid solidification characteristics of impulse atomized Co-based alloys in order to understand and control the application properties of the final products. Amorphous fraction and kinetic crystallization properties of the atomized Co-based alloy powders were quantified by means of Differential Scanning Calorimetry. In addition, different but complementary characterization tools were used to analyze microstructures of the powders. These include optical microscopy, X-ray diffraction and micro-hardness tests. While the amorphous fraction within the powders is promoted by high cooling rate and smaller powder size as expected, hardness is found to decrease with the fraction of amorphous phase.

Jan 1, 2015

By Jogeshwara Sahu, Sapan Kumar Kandi, SANDEEP KUMAR JENA, Sachida Nanda Sahu, Sarada Prasad Das

The present article reports the recovery of potassium from mica scrap using carbide lime waste and NaCl. The acid leaching of mica [4 M H2SO4 at 90 °C] can recover a maximum of 25% potassium. However, in the chlorination roasting (with CLW and NaCl) water leaching process, it was possible to recover potassium to the tune of 94% [900 °C, 50 min roasting; mica:CLW:NaCl 1:0.75:1]. The formation of water-soluble phase like sylvite (KCl) and water-insoluble phases like anorthite ( CaAl2Si2O8) and nepheline ( NaAlSiO4) confirms the complete breakdown of the mica crystal structure. The extraction mechanism proceeds with the formation of a transition state followed by the release of potassium as KCl. The characterisation studies using ICP-OES, XRD, FTIR and FESEM support the proposed extraction mechanism. The salt produced by the evaporation of roast-leached liquor confirms the presence of sylvite and halite only, which can be separated to get the fertiliser grade KCl.

Sep 29, 2021