Search Documents

By Shiou-Chuan Sun

THIS paper presents the design and operation of a frothmeter capable of measuring the frothing characteristics of pine oils and other frothing reagents. The experimental data show that the froth-ability of pine oil is governed by: 1—rate of aeration, 2—time of aeration, 3—height of liquid column, 4—chemical composition of pine oil, 5—pH value of solution, 6—temperature of solution, and 7—concentration of pine oil in solution. The effect of mineral particles on the behavior of froth also was studied, and the results can be found in a separate paper.' The results also show that the relative froth-abilities of pine oils in the frothmeter generally correlate with those in actual flotation, provided that other factors are kept constant. In addition to pine oils, the other well-established flotation frothers were tested, and the results are included. In this paper, compressed air frothing is the frothing process performed by means of purified compressed air, whereas sucked air frothing is the frothing process accomplished by purified air sucked into the glass cylinder by a vacuum system. The term vacuum frothing denotes that froth was formed by degassing of the air-saturated liquid under a closed vacuum system. Apparatus The frothmeter, shown in Fig. 1, is capable of re-producibly measuring the volume and persistence of froth as well as the volume of air bubbles entrapped in the liquid and is capable of being used for compressed air frothing, sucked air frothing, and vacuum frothing. Fig. la shows that for compressed air frothing, the apparatus consists of an airflow regulating system, 1-3; a purifying and drying system, 4-8; a standardized flowmeter to measure the rate of airflow from zero to 500 cc per sec, 9; and a graduated glass cylinder, 13; equipped with an air regulating stopcock, 10; an air chamber, 11; and a fritted glass disk to produce froth, 12. The fritted glass disk, 5 cm in diam and 0.3 cm thick, has an average pore diameter of 85 to 145 microns. The pyrex glass cylinder has a uniform ID of 5.588 cm and an effective height of 63 cm. The inside cross-sectional area of the glass cylinder was calculated to be 24.53 sq cm, or 3.8 sq in. For sucked air frothing, Fig. lb shows that the apparatus for compressed air frothing is used again, with the following modifications: 1—compressed air and its regulating system, 1-3, are eliminated; and 2—a vacuum system, 16, equipped with a vapor trap, 15, and a vacuum manometer, 17, is added. The vacuum system can be either a water aspirator or a laboratory vacuum pump. Any desired rate of airflow can be drawn into the glass cylinder, 13, by adjusting the opening of the air regulating stopcock, 10. The sucked air stream is cleaned by the purifying and drying system, 4-8, before entering the glass cylinder, 13. When this setup is used for vacuum frothing, the air regulating stopcock is closed. The frothmeter has been used for almost 3 years and has proved to give reproducible results, as illustrated in Table I. With a magnifying glass and suitable illumination, the frothmeter also can be used to study the attachment of air bubbles to coarse mineral particles.' Experimental Procedures Except where otherwise stated, the data presented were established by means of the compressed air method. The volume and persistence of froth were recorded respectively at the end of 4 and 6 min of aeration at a constant rate of airflow of 29.3 cc per sec, which is equivalent to 71.6 cc per sq cm per min, or 462.6 cc per sq in. per min. The aqueous solution for each test, containing 1000 cc of distilled water and 19.2 ± 0.5 mg frothing reagent, was adjusted to a pH of 6.9 0.2. The volume of froth is expressed as cubic centimeter per square centimeter and is equivalent to the height of the froth column (the distance between the bottom and the meniscus of the froth). The volume of froth was obtained by multiplying the height of froth by the cross-sectional area of the glass cylinder, 24.53 sq cm. Before each test, the glass cylinder, 13, was cleaned thoroughly with jets of tap water, ethyl alcohol, tap water, cleaning solution, tap water, and finally distilled water. The cylinder with stopcock,

Jan 1, 1953

By Shiou-Chuan Sun

THIS paper presents the design and operation of a frothmeter capable of measuring the frothing characteristics of pine oils and other frothing reagents. The experimental data show that the froth-ability of pine oil is governed by: 1—rate of aeration, 2—time of aeration, 3—height of liquid column, 4—chemical composition of pine oil, 5—pH value of solution, 6—temperature of solution, and 7—concentration of pine oil in solution. The effect of mineral particles on the behavior of froth also was studied, and the results can be found in a separate paper.' The results also show that the relative froth-abilities of pine oils in the frothmeter generally correlate with those in actual flotation, provided that other factors are kept constant. In addition to pine oils, the other well-established flotation frothers were tested, and the results are included. In this paper, compressed air frothing is the frothing process performed by means of purified compressed air, whereas sucked air frothing is the frothing process accomplished by purified air sucked into the glass cylinder by a vacuum system. The term vacuum frothing denotes that froth was formed by degassing of the air-saturated liquid under a closed vacuum system. Apparatus The frothmeter, shown in Fig. 1, is capable of re-producibly measuring the volume and persistence of froth as well as the volume of air bubbles entrapped in the liquid and is capable of being used for compressed air frothing, sucked air frothing, and vacuum frothing. Fig. la shows that for compressed air frothing, the apparatus consists of an airflow regulating system, 1-3; a purifying and drying system, 4-8; a standardized flowmeter to measure the rate of airflow from zero to 500 cc per sec, 9; and a graduated glass cylinder, 13; equipped with an air regulating stopcock, 10; an air chamber, 11; and a fritted glass disk to produce froth, 12. The fritted glass disk, 5 cm in diam and 0.3 cm thick, has an average pore diameter of 85 to 145 microns. The pyrex glass cylinder has a uniform ID of 5.588 cm and an effective height of 63 cm. The inside cross-sectional area of the glass cylinder was calculated to be 24.53 sq cm, or 3.8 sq in. For sucked air frothing, Fig. lb shows that the apparatus for compressed air frothing is used again, with the following modifications: 1—compressed air and its regulating system, 1-3, are eliminated; and 2—a vacuum system, 16, equipped with a vapor trap, 15, and a vacuum manometer, 17, is added. The vacuum system can be either a water aspirator or a laboratory vacuum pump. Any desired rate of airflow can be drawn into the glass cylinder, 13, by adjusting the opening of the air regulating stopcock, 10. The sucked air stream is cleaned by the purifying and drying system, 4-8, before entering the glass cylinder, 13. When this setup is used for vacuum frothing, the air regulating stopcock is closed. The frothmeter has been used for almost 3 years and has proved to give reproducible results, as illustrated in Table I. With a magnifying glass and suitable illumination, the frothmeter also can be used to study the attachment of air bubbles to coarse mineral particles.' Experimental Procedures Except where otherwise stated, the data presented were established by means of the compressed air method. The volume and persistence of froth were recorded respectively at the end of 4 and 6 min of aeration at a constant rate of airflow of 29.3 cc per sec, which is equivalent to 71.6 cc per sq cm per min, or 462.6 cc per sq in. per min. The aqueous solution for each test, containing 1000 cc of distilled water and 19.2 ± 0.5 mg frothing reagent, was adjusted to a pH of 6.9 0.2. The volume of froth is expressed as cubic centimeter per square centimeter and is equivalent to the height of the froth column (the distance between the bottom and the meniscus of the froth). The volume of froth was obtained by multiplying the height of froth by the cross-sectional area of the glass cylinder, 24.53 sq cm. Before each test, the glass cylinder, 13, was cleaned thoroughly with jets of tap water, ethyl alcohol, tap water, cleaning solution, tap water, and finally distilled water. The cylinder with stopcock,

Jan 1, 1953

By Gordon A. Irons

"Powder injection for melt refining is widely practiced in the steel industry, and is gaining acceptance in the non-ferrous industries. In these commercially-important systems, the thermodynamics and kinetics may be very complicated. More than one element may be removed by refining, and often the refining agents are not just one compound. In this paper, the thermodynamic and kinetic aspects of these processes are reviewed. A number of examples are given, such as the desulphurization of iron with a variety of reagent mixtures, and selenium removal from copper with several different reagent combinations.IntroductionI am very pleased and honored to present a paper at this Symposium recognizing the many contributions of Professor Howard Womer. Even at the time I was an undergraduate student, the WORCRA process was part of the curriculum. I remember at the time that I was fascinated by the concept, and due to it and the many other rapid developments in Process Metallurgy, I chose it as my field of study. I think the Symposium is testimony that Professor Womer has touched the lives of many others as well.My original assignment was an overview of the basic aspects of gas and solids injection. However, I reviewed most of this material at the Savard/Lee Symposium [1]. In the present paper, I will present some of the basic issues related to refining with powder injection, using work that we have recently completed in both ferrous and non-ferrous systems."

Jan 1, 1996

By R. C. A. Thurston

INTRODUCTION THE deleterious effect of stress raisers or notches on the resistance to fatigue of machine components, and other parts subjected to repeated dynamic loading, has been well known for many years. Most engineers in the mechanical field have, at one time or another, encountered a shaft which fractured due to a poor transition fillet, a holding-down bolt which failed due to insufficient tightening or inferior thread form, or a fitted member which broke through a combination of fretting corrosion and clamping stresses. All of these are examples of the damaging influence exerted by stress raisers in fatigue. Other common forms of stress raiser which have taken their toll of dynamic components are: keyways, oil holes, splines, quenching oil grinding cracks, tool marks, and sharp changes in section; some are the result of the design, others of poor execution of the design. It is our experience in the Mines Branch1 and I feel sure this will be corroborated by other fatigue investigators, that the majority of failures are due to incorrect design or faulty preparation of the part concerned, rather than to the use of inferior material. Quite frequently, it is true that the operating conditions necessitate the presence of a 'notch', but even in such cases methods are generally available by which its adverse effect on the life of the component can be reduced or annulled. The purpose of this paper is to discuss a few typical stress raisers, and to provide information on various processes for mitigating their effects in fatigue.

Jan 1, 1951

By J-L. Tang

A new rhcoforming processing of Al alloys with component shaping systems apart from slurry preparation systems is experimentally exploited, using the reversible multilevel-speed electromagnetic stirrer, the slurry transfer tool and its coating, the thin plate sample with five steps and rheocasting mould, all of which are independently developed. The results show that semi-solid A356 alloy slurry with shape factor of about 0.85 and particle size of 70~80 µm (under air-cooling condition) could be prepared in 20~25 s, fully meeting the production rate of high pressure die casting. The slurry could be smoothly transferred from the slurry preparation equipment to the rheocasting shot chamber while the slurry temperature of slurry decreases by no more than 3 . The tensile strength and elongation of the semi-solid rheocasting samples could be respectively increased by 11.6~18.2 % and 42.5~50 % compared with the traditional liquid die casting ones, and the rheoforming processing has close affinity with the traditional hot working processes.

Jan 1, 2007

By Jerome F. Sheldon

The earliest recorded history in the use of belt conveyors in the United States is in O. Evans' "Miller's Guide" published in Philadelphia in 1795. Evans defines a conveyor as a "broad endless strap of thin pliant leather or canvas revolving over two pulleys in a case or trough." (Ref. 1) In this definition, pulleys are being used in a bulk material belt conveyor application. Pulleys used in belt drives can trace their origin back to 1200 A.D. In fact, Engineers had considerable experience designing them into drives transmitting greater horsepower than those used in the early belt conveyors. In belt conveyor application, a pulley's purpose is primarily three-fold, 1) support the belt in directional changes, as designed in the conveyor, 2) transmit driving power to the belt, and 3) guide or train the belt. There are various types of pulleys used in belt conveyor systems and these are thoroughly covered in "Belt Conveyors For Bulk Materials" prepared by CEMA, 1966. For our discussion, however, the most common used in belt conveyors are drive pulleys, snub pulleys, head pulleys, tail pulleys, takeup pulleys and bend pulleys. The drive pulley imparts the driving force to the belt and may be located at the head or discharge end of the conveyor, in return strand, or at the tailor loading end of the conveyor. A snub pulley is located near the drive pulley to provide more arc of contact between the belt and pulley for maximum

Jan 1, 1971

At the Kidd Creek mine operated by Ecstall Mining, Ltd. near Timmins, Ontario, Honeywell has installed a sophisticated new quick- thinking computer system that keeps tabs on conditions along three separate processing streams at once and relays continuous 60-second data to the mill operator. Believed to be the first of its kind, the system picks up data from two independent x-ray spectrometers simultaneously. A digital computer from Honeywell's Computer Control Division receives and interprets real-time information gathered by online x-ray analyzers, and the system then advises control room operators of the relative amount of each of five elements at five points in each of the three process streams. The system is reported to provide a quantitative analysis of the five elements at a given point in the process within one minute-which is about 120 times as fast as a chemical laboratory assay could be performed. With this instant data at his command, the mill operator can make timely process adjustments to correct any deviation from optimum flotation results, thus salvaging valuable minerals that would inevitably be lost with slower detection methods. The minerals recovered at Kidd creek are copper, lead, iron, silver and zinc.

Jan 8, 1968

By Fabiano Soares

Strand guide rolls in continuous casters are crucial components for guaranteeing an optimum process for the production of high-quality steel grades. The properties of these rolls greatly influence the quality of the slab produced. The most commonly used designs so far have been the axle roll and the solid roll. A quite new roll concept is the STEC-Roll®. It combines the advantages of the axle roll with those of the solid roll. This paper explains the development of this roll type and shows the current design. The characteristics of the STEC-Roll® are presented in greater detail and are underlined by a number of simulation results. Beside the design itself, the benefits for casting and maintenance are explained, including for example the easy assembly and dismantling or the use of the roll for dry casting. A brief examination is made of the TCO for the STEC-Roll® and an estimation is provided of the exchangeability of this roll. To conclude, an overview on the current applications is presented.

Aug 17, 2017

"For a good many years the Bureau of Mines and various state mining experi¬ment stations have endeavored to develop some method of utilizing the immense deposits of lignite in the United States. Work in relent year has indicated that the best method of this is to drive off the moisture and most of the volatile water from the lignite in some form of carbonizing apparatus leaving a residue high in fixed carbon and low in moisture and volatile matter, which by briquetting can be made into a high-grade fuel. The earlier forms of carbonizing equipment tried were complicated, costly to build and keep in repair, and could not be operated intermittently without being seriously damaged. During the year 1922, however the Bureau of Mines devised a very simple carbonizing oven which produces a uniformly well carbonized product. This oven is essentially a vertical shaft with means for supplying raw lignite at the top and discharging the carbonized limited at the lower end. Air in regulated amount is admitted to the shaft at two horizons, and a zone of combustion maintained through which the column of lignite passes. The lignite is thus carbonized by construction of its contained matter and a small proportion of its fixed carbon, leaving most of the fixed carbon in the carbonized product or ""char"". The degree of carbonization can be closely controlled by varying the volume of air supplied to the oven and the rate of travel of the charre down the shaft.The ""lignite char"" produced is a soft material resembling charcoal more than coal or coke, but somewhat harder than charcoal. A typical analysis is shown in the table headed ""Fuels,"" further on in this papers."

Feb 1, 1924

By Y Zhou, Y Liu, J-P Yang, P Wang, K Hu

"Large-scale mine reclamation has taken place recently in response to the implementation of mining regulations in China. Effective monitoring of the progress of reclaimed land is a critical procedure to assess the quality of reclamation program and to ensure that mining enterprises fulfill their reclamation responsibilities. The present paper reports a preliminary study that examines the situation of mine land reclamation monitoring. Based on the monitoring, some general requirements for mined land reclamation have been proposed, including: the monitoring should be systematic and comprehensive the monitoring should be adapted to specific local conditions the monitoring should be reasonably optimised via scientific methods and technology the monitoring should stick to a variety of national technical criteria.The aim of land reclamation monitoring is to evaluate changes of critical indicators closely reflecting the development trend of the reclaimed mined land, to develop or improve the criteria and technical parameters specific to the site, and to prevent secondary environmental degradation. Based on these requirements and aim, the monitoring should cover the progress of reclamation, establishment of vegetation and plant community development; and recovery of land and water quality in the reclamation area. Regulatory measures are proposed which would improve the work of mine reclamation monitoring in terms of regulation, organisation and financial support.CITATION :Wang, P, Yang, J-P, Zhou, Y, Hu, K and Liu, Y, 2012. The primary framework for the mechanism of the mine reclamation monitoring in China, in Proceedings Life-of-Mine 2012, pp 47-50 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By A. S. Hall

Significant pyrite often does not dissolve in the Sobek (1978) nitric acid extraction; therefore, the standard conservative approach is to estimate pyrite using sulfur present in the sum of the nitric acid and residual sulfur fractions. Alunite, when present, appears as residual sulfur. Because alunite does not generate acidic effluents, overestimation of AGP can occur if all residual sulfur is assumed to be undigested pyrite. Evaluation of 16 samples from the Florida Canyon Mine revealed that petrographic examination coupled with a modification of the Sobek method to include a 6 hour hot (250°F) 'nitric acid extraction resulted in a more accurate estimation of AGP.

Jan 1, 1999

By O. Q. Leone

Composite diaphragms were used in the investigation of electrowinning Ti from TiC14 in a fused LiCl-KCI-TiC'2 electrolyte. Composite diaphragms tested were of two general classes--those consisting of two or more solid materials, and those which contained, in addition, a loose material. An electrowinning cell using a flat diaphragm is described. The maximum current density for these diaphragms was 300 amp per ft2. Lower currents permitted longer operation times. The composite diaphragms gave electrode efficiencies that averaged approximately 60 percent, and the electrowon titanium was of good quality--some Brinell hardnesses were as low as 68.

Jan 1, 1972

By Racquel Nottingham, Marc Mastrantuono, Freddy Lopez

In the digital era that we live in, connectivity and mobility play a decisive role in our daily activities. In this context, insufficient telecommunication infrastructure gives origin to the so called “dead zones” (areas with poor or non-existing cell phone reception), which hinder economic development in small communities and in many rural areas, since they remain invisible to a larger marketplace due to the inadequate cellular coverage. Several countries are working to identify these dead zones and with this information, establish strategies together with mobile providers in order to improve the existing mobile networks by expanding the coverage areas. As a result of the analysis, it is expected that thousands of telecommunication towers for 4G and 5G networks will be erected in the coming years. Telecommunication towers are slender elements that require large shallow foundations to verify primarily the safety against overturning. However in remote areas, it can be advisable to consider alternatives to the conventional shallow foundations, in order to optimize the use of materials (concrete, reinforcement steel, etc.). The following article presents an overview of intervention projects, where telecommunication towers were founded on micropiles. The micropiled foundations allowed to reduce considerably the dimensions of the originally planned shallow foundations. Furthermore, the use of micropiles allows for additional optimization, in combination with pre-fabricated foundations (i.e., precast concrete elements, etc.). This paper will focus mainly on the design and the execution of the micropiled foundation.

Sep 8, 2021

By R. A. Brown

RIGHT NOW the Canadian oil business is suffering from growing pains brought on by developments outside our borders. I would like, therefore, to place our industry in perspective for you in two ways. I would like first to describe it briefly and let you see it in relation to the world oil industry. Then I would like to bring it back and place it into perspective against a strictly Canadian background. Naturally, in such a discussion, it is necessary to use a certain amount of statistical material. I'll endeavour, however, to keep it to a minimum. Eleven years ago, before the discovery of Leduc, Alberta could boast of having 21,000,000 barrels of crude oil reserves. Five years ago we had 1,810,000,000 barrels. At year end, 1957, our remaining recoverable reserves totalled more than 3,000,000,000 barrels. In 1957, our potential production in Alberta reached an all-time high of 756,000 barrels a day. Unfortunately, our actual average daily production dropped from 393,000 barrels per day in 1956 to 376,000 barrels per day in 1957. And in 1958, to date, it has dropped sharply to around 300,000 barrels per day.

Jan 1, 1958

By M. Shriwas, F. Calizaya

"Recirculation is prohibited in many coal mining countries because of the fear that the re-use of return air would allow the build-up of air contaminants at the workings. The incorrect design and location of a booster fan in any ventilation network can create unsafe condition due to recirculation. The current approach to investigating recirculation using simulation software requires manual effort which becomes tedious in a complex and a large network. An algorithm-based C++ program was designed to detect the recirculation in a booster fan ventilation networks. This program needed an input file prepared from output file generated by any ventilation simulator. This program created an output file for recirculation. This program demonstrated the strong capability to detect the recirculation in a sample network and a coal mine ventilation network. The outcomes of this program were documented in this paper. INTRODUCTION The proper design and location of booster fans eliminate the safety hazards associated with high main fan pressure. Conversely, the incorrect design of booster fans in any ventilation network can create unsafe conditions due to uncontrolled recirculation. The proper utilization of a booster fan derives benefits to reduce the main fan pressure, leakage, and consequently ventilation cost especially with high resistance network due to deep and extensive working area in a mine. However installation of booster fan may create uncontrolled recirculation, if it is not sized and located properly with respect to main fan. Recirculation is prohibited in many coal mining countries because of the fear that the reuse of return air would allow the build-up of air contaminants at the workings. Therefore, it is imperative to check the recirculation while designing and operating booster fan for a ventilation network. This paper deals with an algorithm based C++ program to detect the recirculation in a booster fan ventilation networks. This program was implemented to detect the recirculation in a sample network and a coal mine network. STATEMENT OF PROBLEM The currently available ventilation simulation programs do not give much information about recirculation for the generated solution (fan pressures). The current approach to investigating recirculation using simulation software requires manual effort, i.e., traversing from node to node in the output network by the simulator while keeping tracks of all the nodes that form recirculation paths. This is an easy task in a simple ventilation network, but it becomes tedious and sometimes very confusing in a complex and large network. Moreover, the presence of multiple recirculation paths makes the manual effort more complex and difficult, especially in separating multiple loops that are connected together. Thus, there is a need for a more efficient program that will detect and quantify the recirculation efficiently, for the generated fan pressures. A program is developed to detect the recirculation(s) in a network."

Jan 1, 2015

By T. W. Wlodek

Abstract A simplified method of fatigue testing full-dimension, as-rolled, non-machined, mining drill rods is very desirable to the mining and steel industries in the classification of steels available on the market, through the evaluation of their fatigue limits and endurance strength. In this paper one such simplified method is presented and analysed. The preliminary results show many advantages of this method, such as simplicity and constancy of loading. The type of loading applied more or less simulates the working conditions of the outside fibres of the mining drill rods. Additional advantages of this method are the possibility of testing under dry and wet conditions, its quietness, and its ease of operation. Specially designed adaptors and specially applied techniques of fixing and preparation of samples make possible the breaking of a quarter-octagon hollow drill rod in a free length of uniform section in a rotating beam machine. At first glance this seems to be difficult to achieve. In the first preliminary test three different lots of steel were used. S-N curves under dry conditions were determined. These curves permit of the classification of the drill rods on the basis of the fatigue limit and endurance strength of the outside fibres of the metal, which is dependent to a greater or lesser extent on the effect of surface decarburization, surface imperfections, and special surface treatments. The average slope of the S.N curve in the damaging zone, and the fatigue limit in equal tension-compression rotating bending, were determined for SAE 1080, chromium-molybdenum and nickel-chromium-molybdenum mining drill rods. INTRODUCTION The fatigue limit and the endurance strength of mining drill rod steels are of interest to both the mining and the steel industries. These industries are greatly interested in lowering the cost of mining by reducing the consumption of these steels per ton of ore exploited.

Jan 1, 1951

By L. W. Emery

Undergrorlnd combustion operations were initiated in a 60-acre Bartlesville sand "shoe-string" reservoir in Allen Connty, Kans., in 1956. Tests in separate patterns were conducted using various co~nbinations of air and recycle gas to propagate combustion fronts from the injection toward the producing wells. These patterns were made up of 6 injection and 20 prodrrcing wells Gas and liquid prorluctiorz from each pattern was measured on an individual-well basis, and comparisons were made between the three patterns to ascertain the relative effects of injected gas composition on production behavior. Breakthrough of the combustion front at a well was characterized by an increase in water production from the well followed by an increase in bottomhole temperatrrre to approximately 250" F. After burning fronts had broken through at five producing wells, operations were terminated in 1960. From the total project approximately 79,000 bbl of oil were produced during thermal operations at a cumulative produced GOR of 23 Mcf/bbl. No appreciable change in the character of the produced crude was observed. Combustion in the reservoir was maintained with injected gas compositions ranging fronz 6 per cent oxygen in recycle gas to 100 per cent air. lnjectiotz of large quantities of recycle gas resulted in higher producing GOR's from offset wells than were measured from a pattern into ~vhich straight air ~vas injected. The air required to move the combustion front through I acre-ft of reservoir was computed to be 20 MMscf. This valrre was found to be relatively independent of the quantities of recycle gas injected. The recovery efficiency from the swept area was esti~izated to be about 59 per cent. Areas swept were similar in shape to tlzose obtained with a laboratory potentiometric model. Samples of sund taken from behind the burning front by coring indicated almost total oil removal from the sand. Petrographic analysis of the core samples indicated that the sand had been heated to peuk temperature of rlbout 1,200" F. No rignificant difference in peak temperature was forrnd in two areas where compositions of injected gas were quite different. Compression costs for thermal recovery were estimated to be $1,20/bhl of produced oil. INTRODUCTION The use of the "forward combustion" process as an oil recovery method has received a great deal of attention. This method involves ignition of the formation in an injection well, followed by propagation of a combustion front through the reservoir. Combustion is maintained by the injection of an oxygen-containing gas to react with reservoir hydrocarbons. As the flame front progresses through the reservoir, oil and formation water are vaporized, driven forward in the gaseous phase and recondensed in the cooler part of the formation. In turn, the condensed fluids push oil into the producing wellbores. Completed field tests of the process were first reported by Kuhn and Koch,' and by Grant and Szasz.' Results from other tests have since been reported by Walter,3 by Moss, White and McNeil,' and by Gates and Ramey." ach of these tests essentially utilized a single injection well surrounded by four or more producing wells. Sinclair Research, Inc., elected to do field experimental work using a number of test patterns in a single field in order that comparisons between various operating schemes could be made. The site selected and purchased in 1955 for this experimental work was a 60-acre Bartlesville sand reservoir located in Allen County, Kans. Combustion operations were initiated in mid-1956. Between that time and termination of the project in mid-1960, combustion fronts were propagated from injection wells to producers in three separate well patterns, using different mixtures of air and recycle gas. The test was terminated before sweep of the three patterns was complete so that information about the effect of combustion on the swept areas could be obtained by coring. Results from the test in the form of injection and producing well performance have been carefully recorded, and these form the general basis for this paper. DESCRIPTION OF RESERVOIR The reservoir in which the combustion tests were conducted is a Bartlesville sand "shoe-string", typical of a number of small reservoirs in Southeastern Kansas. Average reservoir characteristics are shown in Table 1. Fig. 1 is an isopachous map of the producing sand showing the reservoir to be approximately 400-ft wide and 2,500-ft long. Maximum net productive sand thickness is 21 ft. Fig. 2 shows a typical core analysis obtained by coring with water-base mud. The reservoir has no appreciable dip and is closed on the sides by degradation of sand into shale. The main body of sand is heavily laminated with shale stringers, which are not continuous between wells. The main reservoir is overlain by 30 to 40 ft of laminated low-permeability sand and shale streaks. No information is available on the original properties of

By Z. C. Shen

As core part of flotation column, aerator has been always priority research. A new type of porous aerator made of stainless sintered microcellular material is designed , which diameter is between 20µm to 40µm. High bubble surface area flux is obtained at low air pressure 20kPa by this type of aerator in water. In order to extend its applied range ,experiments were carried out in alkali slurry (pH=12) , resulting with porous aerator clogged after working 20 days . Sampling the cross-section of aerator detected by microscope and X-ray diffraction ,the reason clogging was found. Then plugging aerator was reactivated after putting it in acidic liquor treated by ultrasonic for about ten minutes. On-line aerator maintenance can be done in no down time , and it can be repetitive-used after recovered ,so reduced capital costs.

Jan 1, 2014

By Hongbo Yang, Tongbo Zhang, Ting Huang, Jingshe Li, Fangfang Song

"Liquid core length is a very important parameter of the process of continuous casting, which directly reflects the cooling status in secondary cooling zone and solidification rate of the slab. In this paper, the billet caster in some steel plant in China was chosen as the prototype of simulating. A numerical simulating model for calculating the liquid core length of continuous casting billet was built by ProCAST software, which was verified reasonable and accurate by pin-shooting technique. Based on the model, the relationships between casting speed, casting temperature and liquid core length of casting billet were found, which was very practically useful for the workers on sit to improve casting billet quality. IntroductionContinuous casting process developed very rapidly because of the high metal yield, energy saving, and low-cost 111• And the quality requirements of continuous casting billet for customers became higher and higher with the fast development of economic121• Internal defect usually is the major quality problem for continuous casting billet[3•61 , which is influenced by the solidification process of casting billet, especially the solidification process of liquid core17•81 • So it is very important to study on the relationship between casting parameters and the liquid core length which means the distance between the crystallizer meniscus and the casting billet solidification end-point. In practical production process, the workers usually control the quality of casting billet according to the liquid core length."

Jan 1, 2013

By Seetharama C. Deevi, Mohammad R. Hajaligol, Sarojini Deevi

"Carbides and nitrides of iron are being considered as magnetic materials for high-density recording due to their chemical stability and high-saturation magnetization values (> 100 emu/g). Iron carbides and iron nitrides with magnetic properties suitable for magnetic media were synthesized by employing a novel synthesis procedure based on fluidization of powders in reactive atmospheres. Fluidized-bed reactors of laboratory, bench, and pilot scale were employed for the synthesis of iron carbide, FeSC2, by reducing and carburizing U-Fe203 in the temperature range of 300 to 550 ºC. A temperature of 400· ºC and a reaction time of 2 to 3 h are found to be optimal for the synthesis of iron carbide. When the carburization was carried out in a reducing and carburizing atmosphere such as carbon monoxide, nucleation and growth of FeSC2 occurred directly from Fe304 with no intermediate phases such as FeO or Fe. Longer carburization times resulted in the deposition of carbon on the surfaces of FeSC2 particles due to Boudouard reaction, and higher temperatures favored the formation of a mixture of carbides such as FesC2 and Fe3C. Iron nitrides were synthesized by reducing u-Fe203 in the temperature range of 350 to 550 ºC, followed by nitriding in the temperature range of 350 to 550·ºC. The powders were characterized using X-ray diffraction, scanning electron microscopy, thermogravimetric analyzer, and a vibrating sample magnetometer.IntroductionRecent demand for high-quality recording of optical, electrical, and audio signals generated interest in magnetic tapes with high-recording densities as compared to the conventional magnetic tapes based on U-Fe203. At present, commercially available magnetic tapes contain maghematite, U-Fe203, as a magnetic material with a saturation magnetization of90 emu/g and a coercive force of 400 Oe. Recording of signals at a higher density per unit volume of magnetic material demands magnetic materials with high-saturation magnetization and a reasonable coercive force. Although metallic iron particles possess a saturation magnetization of 130 to 150 emu/g and a high coercive force of 1000 Oe, the gradual oxidation of iron-to-iron oxides (of lower saturation magnetization) prevents the use of iron particles for high-density recording. In contrast, iron carbides such as FesC2, Fe7C3 and iron nitrides such as Fe4N and Fe3N possess excellent magnetic properties coupled with good electrical conductivities and high hardness. The carbides and nitrides of iron have generated significant interest as magnetic materials for the next generation of magnetic tapes due to their unique magnetic properties and relatively greater oxidation resistance as compared to metallic iron particles [1-4]."

Jan 1, 1994