Search Documents

By A. G. Starliper, H. Kenworthy

A procedure was developed for the separation of lead and sulfur in industrial concentrates of galena by a combination of chlorination and fused - salt electrolysis . Galena could not be satisfactorily electrolyzed in the various media tried ; however , when it was treated with chlorine the resulting lead chloride could be effectively separated electrically into lead and chlorine . An apparatus was designed and constructed to chlorinate galena and to volatilize simultaneously most of the chloridized impurities . By electrolyzing the chlorinated concentrate , a high percentage of lead was recovered . Anodic chlorine was drawn from the cell and was used to chlorinate new feed . In many runs , the recovered metal analyzed from 99.8 to 99.9 percent lead . Lead was also distributed as a chloride in the bath , and a small portion was in the volatile fraction produced during the chlorination step . During a tinuous operation , only 0.1 percent of the total lead was discarded ; 99.9 percent was accounted for in the metal , electrolytic bath , and washed or leached chlorination condensate which was essentially lead chloride . About 95 percent of the sulfur from the galena was recovered as a byproduct of over 90 - percent grade .

Jan 1, 1964

By A. C. Fieldner, S. H. Katz

"Introduction.Recent experiments (Fieldner, A.C., Katz, S.H., Kinney, S.P., and Longfellow, E.S., Poisonous gas from carbon tetrachloride fire extinguishers, Jour. Franklin Institute, October, 1920, pp. 543-565), by the Bureau of Mines have shown that carbon tetrachloride extinguisher liquids when applied to fires produce small quantities of irritating and poisonous gases which may be dangerous in very closely confined spaces where conditions are such that the user can not escape without breathing the fumes. The results of the experiments have been confirmed in an independent investigation by the Underwriters Laboratories (Nuckalls, A.H., Corrosive action and products formed when carbon tetrachloride extinguisher liquids are applied to fires, Nat. Fire Protection Assoc. Quarterly, vol. 14, January, 1921, pp. 221-236) who conducted similar experiments for the purpose of determining the corrosive action of these fumes on metals. Both investigations showed that carbon tetrachloride vapor, hydrochloric acid gas, and phosgene were produced in addition to the ordinary products of combustion, such as smoke, carbon monoxide and carbon dioxide. The Bureau of Mines' tests were made by applying a one-quart extinguisher to a wood fire of excelsior in a gas-tight room of 1000 cubic foot capacity. The glass and metal construction of this chamber limited the experimental fire to very small dimensions. It was, therefore, deemed desirable to make a test on a larger scale in the entry of the Bureau's experimental mine in order to similate more nearly the practical use of carbon tetrachloride and other types of extinguishers in mines.Description of extinguishers.Two series of tests were made under identical conditions on different days. Commercial carbon tetrachloride extinguishers were used in the first series of tests and ""foamite firefoam"" extinguishers in the second series of tests."

Jun 1, 1921

By D. J. Weintritt, R. G. Hughes

Statistics show arz increase in the average depth of wells drilled in recent years. As a corollary to this trend, drilling fluids have been improved in an effort to meet the problems inherent at temperatures approaching 500°F. Of importance are (1) deterioration of mud components and (2) the effect of solids on filtration and rheological properties. High-temperature, stable water-base and oil-bare muds are discussed. Those areas in which differences exist are pointed out. Results are based on data taken from the Fann consistotneter, rheometer and shear-strength measurements, static and dynamic filtration tests, methy-lene blue test for bentonite solids and specific heat measLrrenlents of muds. INTRODUCTION Higher well temperatures go along with the fact that the average depth of wells continues to increase. Recent data by Gardner' lists 137 completions deeper than 15,000 ft for the first half of 1964 with a record second-half total of 167 wells drilling or proposed. In addition, there has been an increase in drilling for steam for power production or mineral recovery. In this application the depths are modest, but the mud may approach the critical pressure and temperature of water. Scearce and Magnon' report drilling mud used at temperatures of about 700°F in the Salton Sea area of California. Most deep wells have been drilled with water-base muds. In recent years, however, there has been a substantial increase in the use of oil-base muds because of technological advances in effective additives. The significance of this development was dealt with in considerable detail by Simpson and his co-workers.3 Additiona1 field data have now been obtained to indicate that oil muds are competitive in control, performance and cost with the best types of water muds for use at high temperaturc. This parallel offer of two very different fluid systems, each offering a similar variability in performance, cost and convenience, has created the need to evaluate the merits of these fluids under specified conditions so that the advantages and disadvantages of each can be weighed in relation to the over-all drilling program. This paper is not intended as a review of all the factors. Rather, it attempts to emphasize: (1) important condltions and facts peculiar to high-temperature drilling muds, (2) that more than one imposed test condition or testing method is necessary to describe the quality of a mud at high temperature and (3) that elaborate experimental precautions are necessary whenever laboratory data are used in selection of a mud for field use. WHAT IS A HIGH-TEMPERATURE DRILLING FLUID? For the purpose of this discussion, a high-temperature drilling fluid is any system so formulated or treated to economically minimize the effects of temperature on the properties of the fluid. Our experience in drilling fluids suggests that these effects become obvious for many mud materials at temperatures of 300F or higher. It is understood that hydrolysis of starches, depoly-merization of certain organic thinners, or irreversible chemical reactions (such as that of clay and lime) can affect filtration, viscosity and shear strength at less than 300F. However, the temperature level is not a serious point and in no way affects the precautions and techniques used in this study. An up-to-date review of the literature on high-temperature drilling fluids and the many variations was treated by Rogers'in 1963. EXPERIMENTAL REQUIREMENTS TESTING EQUIPMENT AND PROCEDURES With the advent of deeper drilling and increased demand for temperature-stable drilling fluids, new testing equipment and laboratory techniques were devised for the evaluation of drilling fluids subjected to elevated temperature and pressure. While the equipment has not been standardized, it is in widespread use. Milligan et al. Qescribe a filtration cell for determining the filtration properties of drilling fluids at temperatures in excess of 300F. They showed the effect of variations in temperature and pressure on oil and water muds filtered in the 300 to 400F range. The dynamic filtration apparatus described by Simpson6 permits the study of the filtration properties to temperatures of 350F for drilling fluids circulated over sandstone cores. Watkins et al.' describe the use of pressure bombs for studying the effect of prolonged periods of elevated temperature upon the gelation or solidification of drilling fluids. Chisholm et a1.' describe the use of a modified cement consistometer adapted for use in drilling fluid evaluations. A similar consistometer is used in this study, although the application and data-recording method have been changed. The consistency of a mud sample is measured by timing the movement of a soft iron bob which is magnetically moved up and down in the sample container.* Changer in the time of travel and the temperature of the mud at that moment are plotted with a two-point Brown Elec-tronik Recorder. A 10-in. chart with a speed of 4-in./hr is used. Fia.- 1 is a generalized internretation of the data ob-

Jan 1, 1966

By S. K. Sharma, ANKUSH GALAV, G. S. P. Singh

Providing a suitable protective water barrier pillar (PWBP) is common to reduce inundation hazards in underground coal mines. The imperative factors influencing its performance include the water head acting on the pillar, cover depth, pillar width, strength properties, and permeability characteristics. The mechanical failure of such pillar is a stress-controlled phenomenon, whereas the hydraulic failure is a strain-based phenomenon. A finite-difference numerical modeling approach was developed to study the hydro-mechanical coupled behavior of protective water barrier pillars. The mechanical stability was evaluated in terms of the percentage of failed (ZoF) and intact zones. The influence of the strain-controlled weakening on the permeability of the flow medium was studied through the coupling of the mechanical and hydraulic effects. The coupled steady-state model was used to estimate the outflow rate and its hydraulic stability. The adequacy of the protective pillar was also investigated by assessing mechanical stability and capability to resist hydraulic pressure against the maximum expected water head. A seepage rate-based classification system has also been proposed to evaluate the seepage potential and assess the hydraulic stability. The model has been validated for two case studies at the cover depth of 136–189.5 m and the existing pillar width of 16–42 m against the water head of 25–141 m.

Aug 18, 2022

By M. Bhandari, D. Norval

The bulk of plain carbon steel is produced through conventional Basic Oxygen or Electric Arc Furnace routes where the development of the AC Ladle Furnace has made it possible to also produce alloy steels. Smaller Ladle Furnaces have limitations such as lower efficiency; high electrode consumption and diminutive yields rendering them uneconomical to operate and making the processing of low carbon steel grades difficult due to carbon pick up. The demand for special steels and alloys with strict specifications is increasing while commodity prices remain competitive. The production of special steels and alloys have specific process control requirements and the development of the induction melting furnace (IMF) has made it possible to produce smaller batches economically. Refining and alloying of the melt in the IMF further enhance the efficiency. The INDUREF furnace offers increased productivity and flexibility through increased thermal efficiency and can be utilised for holding molten metal for further processing such as granulating, atomising, nitriding, alloy additions and desulphurisation of Ferro-alloys and steels. The system utilises a specially engineered ladle which is placed in an induction-heating assembly comprised of a stationary water-cooled copper coil and lamination packs. The addition of equipment for vacuum degassing and decarburisation of steels and alloys is also feasible. Benefits are: ? No electrode consumption or carbon pick-up ? Lower installation, operation and maintenance cost. ? No line-flicker facilitates operation on a weak power grid. ? Good power factor and balanced load ? No skull formation and reduced refractory consumption ? Higher yield of Fe-alloys ? Automatic controlled stirring

Jan 1, 2004

By A. R. Farkoosh, K. Korgiopoulos, McGill University, O. Rodop, L. A. Villegas Armenta

"New generation of Al-Mg-Si alloys with thermally stable dispersoids that prevent recrystallization and grain growth during hot deformation are currently used in automotive components requiring good formability. Alloy chemistry controls the phase formation especially age-hardening precipitates, dispersoids, and primary intermetallic which have pronounced effect on grain structure, strength and formability. In this work, thermodynamic calculations have been used to predict the effects of varying levels of Si (0.5-1.5wt%), Mg (0.5-1.5wt%) and Mn (0.1-2.5wt%) on phase selection. Thermodynamic calculations have been performed in equilibrium and non-equilibrium conditions via the FactSage™ software using the FTlite database. Selected compositions have been cast, heat treated, extruded and characterized through scanning electron microscopy with energy dispersive spectroscopy and electron channeling contrast imaging techniques. The calculations showed that at the hot deformation temperature of ~540 oC, exceeding certain Mg and Si levels would lead to retained *-Mg2Si intermetallics and Si particles at the grain boundaries in addition to a-Al-(Mn,Fe)-Si. It was found that retained *-Mg2Si phase which adversely affects formability can be avoided for Si+2Mg levels lower than 2.3wt%. FactSage calculations also showed that increasing Mn from 0.5wt% to 1wt% leads to an increase in the amount of dispersoids (from 1wt% to 2wt%) that can potentially slow down recrystallization and grain growth during hot deformation and improve formability. Calculations at room temperature also show that for an alloy with 0.7wt% Mg, excess Si beyond 0.7 wt% promotes the precipitation of Si clusters in the Al matrix that accelerate natural age-hardening. Results were confirmed by experimental investigation.INTRODUCTIONAluminum alloy 6082 (Al-Mg-Si) is used in the automotive industry because of its high strength, and good weldability (I. J. Polmear, 2006). The alloy is age-hardenable through the precipitation of ß-Mg2Si and its precursors, and the recrystallization is usually inhibited by Mn- and Cr-containing dispersoids formed through high temperature heat treatments (I. Polmear & Couper, 1988). However, it is known that minor changes in alloy chemistry (Mg/Si ratio) can have significant influences on the ductility and formability of these alloys by altering phase selection and the resultant microstructure (Gupta, Lloyd, & Court, 2001; McQueen & Celliers, 1997; Zajac, Hutchinson, Johansson, & Gullman, 1994). For automotive applications where wrought alloys (usually extrusions) are cold-formed to produce suspension components, the chemistry of the alloys and the extruded structure are of crucial importance as they determine the formability at room temperature (Asensio-Lozano, Suárez-Peña, & Vander Voort, 2014). In this study, thermodynamic calculations along with experimental investigations were carried out on the Al-Mg-Si system to understand their phase formation and precipitation hardening as a function of alloy composition."

Jan 1, 2016

Silver ore was first discovered in 1866 at Manhattan, and a few ore shipments were treated in a mill at nearby Belmont. The district was abandoned from 1869 to April 1, 1905, when rich gold float was discovered on what was to be called the April Fool claim. By early 1906, 4, 000 people lived in Manhattan. The San Francisco earthquake, in April of 1906, caused the withdrawal of capital from Manhattan and most of the mines were shut down. Later that year and in 1907, however, more strikes were made. The camp prospered until the mid-1920s, but a steady production of several hundred thousand dollars per year was sustained even during the great depression. Then, in 1939, Nevada's first bucket-line dredge was installed below the town and operated until 1947, producing $4.6 million in gold. The Houston International Minerals operation at Manhattan was started in July of 1980 at a throughput of about 545 mt per day (600 st per day). In contrast to the early day underground operations, Houston's mine is open-pit and processes low-grade disseminated ores. The ore is a metamorphic schist containing 2. 7 g Au and 1. 03 g Ag per mt (0. 08 oz Au and 0. 03 oz Ag per st). Some coarse gold, up to 1 mm in size, is present. Mining and haulage is done by a contractor. Stockpiled mine-run ore is crushed in three stages comprising a jaw crusher and two cone crushers, with screens ahead of the cone crushers. Crushed product, at about 19 mm (3/4 in.) size, is stored in a silo. Grinding is by single stage ball mill with the discharge passing over two hydraulic traps for coarse gold removal. These traps will be replaced in late 1980 by a two-cell Pan American jig treating the cyclone underflow. The jig hutch product, along with the hydraulic trap product that has been stored, will be treated further for gold recovery. The gravity tails will then be cycloned with the underflow being recirculated in the ball mill and the overflow being treated by flotation. A rougher concentrate is made in twelve No. 48 Galigher cells with the float tails being cycloned. Cyclone underflow is refloated in another four No. 48 cells; the overflow is treated in sluice boxes for further gold recovery before being sent by gravity to the tailings pond. Bulk flotation concentrates are cleaned three times with the final concentrate being thickened. The thickener underflow is then batch cyanided in mechanically agitated tanks and washed with barren liquor

Jan 1, 1981

By B. Genc, C. Gous

Spontaneous combustion during coal mining operations is a major problem that affects the health and safety of workers and causes environmental problems. The phenomenon is associated with the presence of coal, coal shale, and pyrite. In 2020, a premature detonation incident occurred at an iron ore mine where the waste material contains black carbonaceous shale units known to be associated with pyrite. The spontaneous combustion propensity and properties of samples of the black carbonaceous shales from the mine were examined and compared with samples from the Witbank Coalfield. The spontaneous combustion liability indexes of these samples were correlated with X-ray fluorescence (XRF) and proximate and ultimate analyses using linear regression. The Wits-Ehac Index classification results show that the samples were between medium and high risk. The linear regression analysis showed very poor correlations between the Wits-Ehac Index results and the XRF and proximate and ultimate results. The most valuable relationship found is between the presence of relatively high sulphur (greater than 3%) and ground reactivity with nitrate-bearing explosive emulsion.

Jun 5, 2023

We describe a new method of characterising the effect of dissolved materials on the rate of coalescence of bubbles in aqueous media. Single bubbles were allowed to rise to meet the surface of an aqueous solution, and the time of persistence between arrival and bursting of bubble was measured as a function of solute concentration. A laser beam was placed just above the surface of the liquid, with a detector in the light path, so that any disturbance at the surface could be seen as a break in the beam. The arrival of a bubble at the surface could be detected from the behaviour of the trace on an oscilloscope, and when the bubble broke, another significant change in the signal could easily be seen. The time between disruptions was reported as the persistence time. The effect of a homologous series of n-alcohols (C1 to C8) on the persistence time was measured, in aqueous solution. It was found that with increasing concentration of a particular solute, the persistence time increased up to a point, and then declined. However the magnitude of the persistence time was found to increase with increasing numbers of carbon atoms in the molecule. Bubbles of 1, 2 and 3 mm diameter were used. Persistence time increased with increasing bubble diameter, the maximum values observed being of order 100 secs. For a given solute, the persistence (drainage) time increased with increasing bubble diameter. The concentration Cmax at which the maximum persistence time was observed, was found to be independent of the bubble size. It decreased uniformly as the carbon number increased, and was well correlated by the function y1/2 (dy /dc) -2 I dc)-2 . There was no apparent correlation with the surface excess at maximum persistence time.

Jan 1, 2006

By R. Matusewicz, A. Kaye

Ausmelt Top Submerged Lancing (TSL) Technology has gained widespread commercial acceptance in non-ferrous applications, including the processing of lead and zinc primary concentrates and secondary (post-consumer) materials. TSL is highly flexible and efficient, and is one of the few technologies which can process primary and secondary feeds, and use varying fuels, to deliver high recoveries and excellent environmental performance. With the recent high value of both lead and zinc, and an escalating awareness of the sustainable use of resources, focus on the processing of secondary feed material sources has surged. Ausmelt Technology has proven to be well suited to the economic recovery of values, with twenty-two (22) Ausmelt furnaces processing lead and zinc bearing feed sources now in operation, under design or construction. This paper describes Ausmelt's progress in the fields of lead and zinc processing, and developments in new processing areas such as EAF dust processing and linking to innovative hydrometallurgical technology. Ausmelt has recently committed to the Whyalla Zinc project as the owner/operator of a facility for the treatment of zinc bearing secondary feeds. This project is due for start up in the first quarter of 2008.

Jan 1, 2008

By Brent A. Elliott, J. Richard Kyle

This article reviews the production trends of industrial minerals since 2000 for Texas, the leading U.S. producing state of industrial minerals with a total value of $5.2 billion in 2017, equivalent to 6.9 percent of all U.S. minerals value. Most current Texas industrial-mineral value comes from the production of cement, crushed stone, industrial sand, and construction sand and gravel. Construction material consumption is concentrated in the 25 metropolitan areas of the state, with production of industrial minerals in nearby counties. With Texas’ population projected to reach 50 million by 2050, continuing in-state development and production of industrial minerals will be required to meet in-state and regional demand. Texas’ most rapidly growing production of industrial minerals is industrial sand to supply proppants for multiple unconventional petroleum plays. Texas’ favorable geology and economic factors provide opportunities for the identification and development of new industrial-mineral production sites. Repurposing of former industrial-mineral production sites for post-production development likely will increase as efficient land use evolves. Understanding the geologic, economic and societal framework of industrial-mineral resources will facilitate more informed decisions about the complex issues that the region will face, including effects of sea-level rise on coastal infrastructure.

By H. W. Schreiber, H. R. Babitzke, R. E. Rodriquez, Patterson J. A., C. D. Masters, J. J. Schanz, R. B. McCammon, E. A. Noble, P. M. Krishna

A five-year effort by the ASTM subcommittee E10.14 on uranium resource evaluation has culminated in the approval of E901-82, Classification System for Uranium Resources (ASTM Standard E901-82, April 1983). The standard classification was prepared with participation of representatives from the US Department of Energy, the US Department of Interior's Geological Survey and Bureau Mines, utilities, and consultants. The classification a resource is based on level of knowledge and the economic producibility of the resource at a given time. Alphanumeric identifiers are used rather than words to avoid confusion with existing terms, definitions, and classifications. An example demonstrates the dynamic nature of the process of classification and attests to the necessity of addressing both the aggregate needs of broad-scale resource planning and the specific needs of individual property evaluation. Problems that remain infixing the classification a given uranium resource include uncertainty in estimating the quantity of undiscovered resources and resolving differences that may exist in deciding when the drill-hole spacing is adequate to determine the tonnage and grade of discovered resources.

Jan 1, 1985

By D. Scott Scovira, Remi Proulx

The Meikle Mine is a high grade, underground gold mine utilizing primary-secondary longhole open stoping with delayed backfill to produce 3000 stpd of ore. Hot and reactive ground conditions were encountered early on in the mine life. Ground temperatures up to 330” F were measured. In the early stages of mining, the mine experienced premature detonations using different explosives. The learning curve to safely mine this high-grade gold deposit in hot and severely reactive ground was indeed very steep. Currently, the Meikle Mine uses a special buffered bulk emulsion in all blasts to address hot and reactive ground concerns. In addition, exacting procedures are also followed to ensure safe work with explosives. The combination of new explosives technology and strict loading procedures permits high mine productivity with the highest degree of safety.

Jan 1, 2000

By Sara Moshfeghi, Seyyed Majdeddin Mir Mohammad Hosseini, Abolfazl Eslami

"Due to variety of current pile bearing capacity methods based on the cone penetration test (CPT), for optimum design, it is necessary to evaluate the performance of such methods in different geotechnical conditions. Geotechnical databases including piling and in-situ testing records have been recognized as useful tools for analysis, design and economical construction. In order to evaluate pile bearing capacity methods, AUT-CPT&Pile database has been compiled including 450 full scale pile load tests and CPT sounding records. This database consists of different pile types with a relatively wide range of geometries and various soil conditions. Forty three records of piles driven in sand deposits were then employed to evaluate effects of ultimate capacity interpretation criteria from load displacement diagrams. The Davisson offset limit criterion, the Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter were compared to estimated capacities from ten CPT based design methods currently used in practice. The Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter lead to reasonable results, the Brinch Hansen 80% criterion showed less scatter. For evaluating the accuracy and the precision of CPT-based methods, the results were compared to estimated capacities. Results of comparison indicate that the CPT-based methods mainly predict the pile capacity withreasonable accuracy.INTRODUCTIONAmong the different approaches of estimating the pile bearing capacity, in-situ tests, especially, the cone penetration test (CPT) are favored due to the cone similarities with piles in modes of installation as well as fast and continuous profiling. This trend is practically well established where deep foundations are to be constructed in soft to medium subsoil deposits (Eslami and Fellenius, 1997; Mayne and Niazi, 2009).Employing different design methods results in a wide range of values which complicates the selection of an appropriate one to determine the pile bearing capacity. Several studies by Briuad and Tucker (1988), Eslami and Fellenius (1997), Abu Farsakh and Titi (2004), Schneider et al. (2008) and Eslami et al. (2011) confirm disparity of different design methods predictions. Thus, for optimum design, it is necessary to evaluate and compare the performance of current methods.Geotechnical databases are known as helpful tools in research and practical applications for optimizing analysis and design and are mainly used for management and interpretation of data, evaluation of design methods, calibrating LRFD or ASD design factors, etc. Pile lateral and axial load tests are examples of databases in geotechnical engineering. A summary of several CPT and pile load test databases is presented in Table 1."

Jan 1, 2017

By T. Gerritsen, T. Plikas, K. Ochoa, M. Loveless, R. MacRosty, J. Reichart, R. Pula

Sidewall accretion in a smelting furnace plays an important role in furnace integrity as it provides protection to the sidewall cooling elements and thereby extends the furnace campaign life. The extreme thermal and mechanical stresses in the furnace and changes in the slag chemistry can cause the sidewall accretion to melt or break away decreasing the lining protecting the cooling elements. Thin accretion is highly undesirable as it increases the risk of exposing the cooling elements to the molten bath and in the worst case may lead to a failure. Therefore, monitoring the sidewall accretion on an operating furnace is extremely important to manage furnace integrity and to support safe furnace operation. Operators often generate estimates for sidewall accretion and refractory thickness using either copper cooler temperatures or heat load into the cooling water circuits. Multivariate statistical models, on the other hand, have the capability to consider all the process measurements simultaneously to provide a more reliable estimate. This paper describes the application of multivariate statistical models for sidewall integrity monitoring on a Flash Converting Furnace (FCF) and also discusses the online implementation of these models as the Sidewall Accretion Monitoring System. INTRODUCTION Rio Tinto’s Kennecott Utah Copper (KUC) smelter located near Salt Lake city, Utah operates a Flash Smelting Furnace (FSF) and a Flash Converting Furnace (FCF) to produce high-grade matte and blister copper respectively. Since the commissioning of smelter in 1995, several improvements were made to these furnaces to increase their efficiency and operational safety. At present, Kennecott smelter is known to be among the lowest-emission and highest energy recovery copper smelters in the world. Since the smelter start-up, Kennecott has invested in several advanced furnace monitoring practices to evaluate the integrity of the furnaces and improve their campaign life. An example is their temperature monitoring system installed for the smelting and converting furnaces, which continuously monitors the furnace sidewall temperatures and notifies the operators during temperature excursions. During an investigation on the converting furnace, it was revealed that there were frequent temperature excursions in the settler sidewall area towards the reaction shaft end of the furnace that caused significant furnace downtime. The reason for the sidewall temperature excursions was not clearly known.

Jan 1, 2019

By Jens Kempken

A competitive landscape pressurizes the steel producers business, zero defect requirements from customers forces the operators for additional efforts in process control and quality management. The so called quality related cost, which include also rework, cost for downgrading or even scabbing of material is already a remarkable lever in a plants profitability breakdown. The introduction of advanced state of the art grades in the product portfolio requires already a budgeting for the expenses for R&D and quality management. PQA has been developed as a process and quality management software solution next to existing level 2 or level 3 automation systems. It is focusing on the analysis of process data, equipment information, in line quality measurement devices and trend analysis to obtain an answer whether the process is according to definition and expectation and whether the intermediate or final product can be shipped for further processing as prime material. Advanced analytics which are linked to an expert know how based configuration identifies deficiencies in the production and processing process. An intelligent, state of the art quality rating system evaluates tolerable deviations. PQA comprises the software platform including the database, data configurator and collector from the different sources in the production process and units. The core element of the platform is the knowledge based expert know how package defining process and quality determining fundamentals. The paper describes the structure of the software package, it gives insights on the expert know how package, process and quality evaluation and points out the customer benefits, cost reduction, improvement yield, customer satisfaction increase. The link to recent operational references is given.

Oct 30, 2017

By Guo Chen, Yifeng Shi, Xiaobiao Shang, Nanshang Shen, Bangqi Zhang, Jinhui Peng, Junruo Chen

"The energy is introduced directly into the volume of the honeycomb ceramic regenerator due to the complex interaction of microwaves with minerals in microwave gas heating system. A three-dimensional numerical model is developed to simulate the electromagnetic field by solving Maxwell's equations using finite-difference time-domain method. Computational result is presented for the microwave power absorption of the regenerator. Effects of the dielectric constant and the effective loss factor on the microwave power absorption in the regenerator are studied as well. Numerical results show that the heating pattern strongly depends on the dielectric property of the regenerator. The demonstration of the model of electromagnetic field distribution can be applied effectively and efficiently to optimize the fundamental parameters in the microwave heating processing.IntroductionIn recent years, microwave energy has been utilized in many fields, such as food processing, chemical engineering and mineral processing [l]. In contrast to conventional heating, where heat is transferred from a surface to the interior, microwave energy is introduced directly into the volume of minerals due to the complex interaction of the microwave with the mineral. Based on volumetric heating effects, microwave heating has several advantages such as pollution free, rapid heating technique, internal heating, high efficiency over conventional heating [ 1-4]."

Jan 1, 2013

By J. Finch, R. McIvor

This paper presents the development of a new grinding circuit steady-state modeling system. It is fundamentally based on the “functional performance equation”, which has now been used to improve the performance of numerous grinding circuits. This equation characterizes the two distinct efficiencies that are at work in a ball milling circuit, and how these relate to overall circuit productivity. It does so based on the particle size chosen to distinguish between coarse and fine (product size) material. Now, by applying it to all the material size classes, a simple yet reliable ball mill model was created. Combined with cyclone recoveries, the complete, detailed grinding circuit performance can be exactly reproduced mathematically by the computer program. It can then be used with separate process equipment application engineering methods to systematically engineer grinding circuit improvements. The development, features, uses and limitations of the system are described.

Jan 1, 2007

By R. Dekkers

Non-metallic inclusions in liquid steel are mainly formed during killing. As far as these particles are not captured by the slag, they are found in the cast steel where they can deteriorate the mechanical properties. Inclusions may also disrupt the continuous casting process, affecting thus directly the quality of the steel and the production capacity. Steel pin samples from the Sidmar plant (Belgium) were taken in different steps of several ladle treatments and in the tundish. Also slab samples were studied. All samples concern the same type of low alloyed aluminium killed steel. The non-metallic inclusions were isolated from the steel matrix and investigated with scanning electron microscopy and energy dispersive spectrometry. The evolution of the non-metallic inclusions is described by their number, size, shape and elemental composition. The main non-metallic inclusions present are aluminium oxides and spinel type compounds.

Jan 1, 1999

By N. A. Warner

To filly secure the environmental and social acceptability benefits of making a sulphide smelting facility and its ancillary sulphuric acid plant or other means for fixing sulphur, a virtually zero gas emission operation, it will be necessary to utilise exclusively technically pure oxygen. The strategy proposed for preventing the smelter from overheating involves highly efficient energy transfer by promoting sulphur trioxide formation at a relatively higher temperature than normal. A closed-loop gas circuit uses an eductor system actuated by the process oxygen to recirculate sulphur trioxide and unconverted sulphur dioxide back to the smelter, the endothermic dissociation of sulphur trioxide becoming a major contributor to the removal of excess heat. The only gases leaving the system relate to the bleed of nitrogen impurity introduced in the tonnage oxygen.

Jan 1, 1998