Search Documents

By J Say, M Hawtin, L Carlon, P Cann

Historically, production from sublevels of the Ernest Henry Mine (EHM) started from blind uphole rises at the end of slot drives. Where previous investigations considered removing these slot drives and starting production with independent ore drives, any development savings were consumed when drives were extended to minimise ore loss. Since 2017, EHM and Orica have been investigating opportunities to optimise drill and blast practices by implementing Orica’s Wireless Electronic Blasting System (WEBS). To reduce ore drive development metres, a novel design was proposed utilising the WebGen™ 100 system to combine a rise with pre-charged widening firings. Initially these new rise and widening firings achieved results similar to previous EHM designs, achieving on average 81 per cent of design height and width. Due to poor performance of the fourth trial a significant re-design was required. Modifications included drill hole re-positioning, in-hole primer relocation and initiation delay adjustments. Since the re-design a step change in rise performance has been observed with rise and pre-charged widening shots averaging 95 per cent of design height and width. With rise and widening performance exceeding expectations, the removal of slot drives has allowed a substantial reduction in lateral development. Development savings of 165 m and 169 m from the RL1325 and RL1300 levels have been achieved. Primary draw and ore recovery has also increased due to the later addition of pre charged forward stripping rings. Level design changes have also significantly improved the mining cycle by allowing for a reduction in required ground support, improved secondary ventilation, a reduction of critical path development, simpler production scheduling and less wear and tear on machinery. Future mine level designs now incorporate key learnings and are proving beneficial to a variety of scenarios including changing orebody boundaries at depth.

Mar 15, 2021

By Walter Knox, J. D. Doherty

In 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. Summary OF Results Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3)- 2' The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages Over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 11.6 per cent to 19.2 per cent. There was a notice- able segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may be a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance ,. The, removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. with intermittent operation the burning rate was almost always less than the feeding rate, The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. 13). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). Guiding Principles In planning the investigations, the following principles were adopted: Selection of Heating Equipment.—Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By Walter Knox, J. D. Doherty

In 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. Summary OF Results Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3)- 2' The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages Over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 11.6 per cent to 19.2 per cent. There was a notice- able segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may be a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance ,. The, removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. with intermittent operation the burning rate was almost always less than the feeding rate, The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. 13). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). Guiding Principles In planning the investigations, the following principles were adopted: Selection of Heating Equipment.—Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By H. R. Stahl

FIVE mills are operated in Southeast Missouri by the St. Joseph Lead Co.; these have a total rated capacity of 24,300 tons per day divided as follows: Federal, 12,000 tons; Leadwood, 4800 tons; Desloge, 3600 tons; Bonne Terre, 2400 tons; and Mine La Motte, 1500 tons. These concentrators are similar in a general way, differing mainly in size and type of equipment and in minor variations in flow sheet. No attempt is made rigidly to standardize procedure in the various mills in spite of a general similarity in the ores. Each mill may be regarded as a separate laboratory in which new ideas and changes may be tried. A generalized description of the process is given, noting important differences in procedure at the various plants. The concentration process may be divided into five main stages: dry crushing, wet grinding, desliming and classification, tabling, and flotation.

Jan 1, 1947

By Claudia Gasparrini

Uranium occurs in a variety of minerals, the more common primary ones of which are uraninite-pitchblende, coffinite and a group known as the complex multiple oxides. Identification and description of the uranium-bearing and associated minerals in ore samples may give a preliminary indication of the potential economic importance of the deposit and may also suggest initial approaches to metal extraction. The present paper reviews the common uranium minerals, describes their manner of occurrence and compares the types of deposits with which they are associated. Methods and techniques for their identification are described and their leaching characteristics discussed.

Jan 1, 1981

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By D. J. Gurtler

On January I, 1988, Chino Mines Company initiated the use of a system of economic splits for all materials encountered in mining. All mined material is evaluated as mill ore, solvent extraction-electrowinning plant feed and non-ore material to determine its disposition. Post-implementation studies indicate that a significant increase in financial returns on material mined was realized when compared with the copper cut-off grade previously in use.

Jan 1, 1990

By F. Charette

The paper reviews the requirements of the instrumentation required to monitor mining excavations in a high stress environment, and the development plan to instrument the D-Bolt in such a fashion as to be able to follow the behaviour of the bolts in relationship to the ground movements and support performance. Recent field observations of D-Bolts under static and dynamic conditions are also presented. Also discussed is the assumed mechanical behaviour of the D-Bolt. D-Bolts are used in two (2) Canadian underground mines operating in high stress environments and tested in three (3) other operations.

Jun 1, 2012

By B. W. Zhao

Quantitative analysis of minerals composing in ore is primary in process mineralogy, a veracious quantification and analysis is very crucial to optimize or design a beneficiation process, especially for a low grade and complicated ore. This paper will discuss a SEM-EDS based quantitative analysis developed in JKtech Australia through an example from Jinchuan lean ore. For a low grade, com-plex intergrowths and texture lean ore, chemical phase analysis of value minerals and identification by optical microscope are very essential, unite the SEM-EDS based quantitative analysis, we can understand exactly the lean ore, explain and quantify the process performance.

Jan 1, 2014

By V. Polotski

This paper describes a platform for autonomous operations in open pit mining environments. A typical operation consists of: (1) Initial locomotion toward a remote worksite; (2) Pattern navigation within the worksite; (3) Worksite manipulations and (4) Return locomotion to the start location. The platform includes precise localization module based upon the fusion of odometry, inertial and GPS measurements. The guidance module starts from a set of way points specified on a GPSreferenced map and plans and executes the mission. A typical mission includes specified manipulative tasks along the navigation path. During motion execution the on-board system continuously verifies that the path is free of obstacles and that the hardware is not overloaded. Momentary losses of external positioning measurements does not adversely affect the performance, owing to the redundancy in position and heading estimation. A rehearsal phase follows planning and allows the supervisor to examine the kinematic behavior of the platform during motion, thus reducing the need for continuous monitoring during execution and providing protection against potential losses of communication.

May 1, 2003

By Juliano Braz Possatti, Arnaldo Carneiro Salles, Cleudson dos Santos Rego, Leandro de Lucas Mendes

The increase in customer demand for steels with higher surface requirements, associated with the need to increase ArcelorMittal Tubarão's HSM productivity, it was necessary the development of controls and actions to reduce scale losses within the scenario of high productivity. This article describes the path followed by the hot strip mill team in order to reduce the occurrence and severity of scales.

Oct 10, 2019

By Sanchita Chakravarty, Sumantra Bhattacharya, Divya Jyoti, A. K. Mukherjee, Soni Jaiswal

"Release analysis is independent of collector and frother dosage and type, but it is primarily influenced by the degree of liberation or “state of release of the sample”. The shape of release curve is an indication of the degree of liberation. This paper briefs about the effect of reagent combination, particle size and surface characteristics on the release analysis of difficult-to-clean LVC coal.Release analysis of three LVC coal fines obtained from two different coalfields of India was carried out at three different size levels such as -0.5mm, (-0.5+0.1) mm, and -0.1mm. The collectors used were n-dodecane and commercial diesel oil. Incomplete liberation of coal fines even at a size of -100µm, corroborated by photomicrographs of ROM and clean coal macerals, in a great measure reduced the flotation-based cleaning potential of the fines. FESEM images of fines reveals that the adherence of ultrafine onto the surface of relatively coarser particles reduced the clean coal recovery. The results obtained also appear to be coal, reagent combination and, particle size and particle surface specific. Only one coal indicated the liberation as is usually expected for -0.1mm particles with a reasonable yield of 65% at 18% ash. INTRODUCTION Froth flotation has a long history of being used to treat coal fines. Coal flotation is considered to be difficult, if the percentage of Near Gravity Material (NGM), i.e. essentially locked particles, in flotation feed is >10% [Aplan, 1993], which is usually the case with all the coking coal fines in India. The fines are rich in vitrinite, so valuable for coking coal. Unfortunately, there appears to be no standard procedures to determine the separation efficiency of froth floatation. Release analysis proposed by C.C. Dell in 1953 [Dell, 1953], aimed to determine the ultimate floatability of coal. Several other techniques had been proposed but release analysis technique has been considered to be a vast improvement over the batch flotation process [Forrest et al. 1994]."

Jan 1, 2018

By A. Navarra

Within conventional copper and nickel-copper sulfide smelters, ladles of molten matte are fed into converters. These converters blast oxygen-enriched air into the matte, thereby eliminating iron and sulfur. The converting reactions are exothermic and, indeed, the converter heat balance is often a limiting consideration on the smelter throughput. If a portion of the matte were fed in solidified (granulated) form, this would support higher oxygen enrichment, and lower volumes of converter offgas, allowing higher throughput. This approach is not applied in conventional smelters, partly because of the copious amounts of water that must be evaporated in typical granulators, as in the Kennecott-Outotec process. The current paper recalls a waterless matte granulator that had been pioneered in the 1990’s, and is applicable to conventional smelters. A mathematical formulation is presented that can be used in the context of simulation-based optimization, to estimate the size and impact of waterless matte granulation.

By AIME AIME

ANNOUNCEMENT on August 6 of the historic event of dropping an atomic bomb on Hiroshima, Japan, was more dramatic even than V-E day, since that had so long been forecast whereas the bomb production had been the best-kept secret of the war, even though at one time more than 100,000 people had been at work in connection with its production, and some two billion dollars had been spent on the project. Mining men had long been aware of an unexplained abnormal interest in uranium production, and suspected that something of the sort was on foot, while metallurgists were aware that various men of their acquaintance were engaged in some top secret research. The first announcement was soon supplemented by other official releases which told more about the research laboratories for theoretical and pilot studies, and the plants in Tennessee and Washington, but none of them made clear what the modus operandi is of these terrific bombs. Inquiry at Colum. bia University, where Dr. Dunning and his associates had succeeded in 1939 in splitting the uranium atom, and where laboratories known only as SAM have been feverishly active since the beginning of the war, was unproductive, since none of those officially connected with the project could give out anything beyond the official releases.

Jan 1, 1945

By B. Anameric

The pig iron nugget process is gaining in importance as an alternative to the traditional blast furnace. Throughout the process, self-reducing?fluxing dried greenballs composed of iron ore concentrate, reducing-carburizing agent (coal), flux (limestone) and binder (bentonite) are heat-treated. During the heat treatment, dried greenballs are first transformed into direct reduced iron (DRI), then to transition direct reduced iron (TDRI) and finally to pig iron nuggets. The furnace temperature and/or residence time and the corresponding levels of carburization, reduction and metallization dictate these transformations. This study involved the determination of threshold furnace temperatures and residence times for completion of all of the transformation reactions and pig iron nugget production. The experiments involved the heat treatment of self-reducing?fluxing dried greenballs at various furnace temperatures and residence times. The products of these heat treatments were identified by utilizing optical microscopy, apparent density and microhardness measurements.

Jan 1, 2007

By Y. Guan

The dissolution behavior of copper and gold from their pure state and from Au/Cu alloys in cyanide solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of the composition of the alloys, stirring speed of the disc, concentration of lixiviants and temperature on the overall dissolution kinetics has been studied. Gold/copper alloys of three compositions were used in this study. The atomic percent of gold in these alloys was 75, 50 and 25, respectively. The dissolution behavior of these three alloys was compared with that of pure gold and of copper under the same chemical conditions. In general, the dissolution of copper and gold from alloys is partially controlled by surface chemical reaction and largely by mass transfer.

Jan 1, 1992

By Rogers F. Davis

The Bureau of Mines developed a new method for the determination of oxides of nitrogen in diesel exhaust gas. The procedure, a modification of the Saltzman method, uses a NO2 absorbent for the diesel exhaust gas; the colorless absorbent becomes purple on contact with N~. When used properly this procedure gives satisfactory results in 2 hours, whereas the standard phenoldisulfonic acid method required approximately 8 hours. The new method is not satisfactory for determination of oxides of nitrogen in the overrich fuel to air ratio range.

Jan 1, 1966

By D. H. Chambers, Arnold M. Lansche

Electro recovery by amalgam methods was investigated to determine the feasibility of recovering pure cadmium from cadmium sponge produced during purification of zinc electrolyte at electrolytic zinc plants . Actual material used in this work was air- oxidized cadmium sponge . An acid rinse and zinc displacement technique was developed to amalgamate this oxidized cadmium . ( In - plant use of the recovery process would probably not require this step because of the fresh state of the sponge . ) Zinc was completely removed from amalgamated sponge by selective oxidation with air . Zinc - free cadmium amalgam was circulated by an electromagnetic pump through an electrolytic cell where cadmium of 99.9+ percent purity was electrodeposited onto a rotating aluminum cathode . Polarographic methods were developed for determining cadmium and zinc in mercury and in sulfuric acid solution .

Jan 1, 1964

By J. C. D. Gush

Paper written on project work carried out in partial fulfilment of Laboratory-scale testwork was undertaken to recover oxidic copper-cobalt minerals by froth flotation, which requires maintaining a certain sulphide level in the pulp. To improve control of the sulphide concentration, an electronic closed-loop system was designed that responds to the potential output of an ion-selective electrode. The PID control was improved by adding a pre-emptive control and a self-calibration feature; a data logging facility is also included. An inexpensive valve design was incorporated using locally available parts. The operating results of this control design are presented.

Jan 1, 2005

By Li N, Grimsey E. J

A technique has been developed for the fast measurement of the liquidus temperature of molten salt systems. The method employs a type K thermocouple embedded within the centre of a copper cylinder. The cylinder is immersed into the molten salt bath and the resultant heating curve is recorded using a PC-based data logging system. Upon immersion of the cylinder into the bath, a layer of salt freezes from the melt onto the surface. When this layer remelts during heating, the shape of the heating curve exhibits a change. The onset of this change can be detected by numerical differentiation of the heating curve, and the temperature at the onset represents an estimate of the liquidus of the melt. This work describes the technique and its application to the measurement of liquidus temperatures of MgC12 - NaCl and BaC12 - NaCl salt mixtures, in addition to a number of solidus temperatures.

Jan 1, 1996