Search Documents

By Timothy C. Siegel

Given that piles are composed of different materials and installed using a variety of methods, ASTM D 1143/D 1143M-07 Standard Test Methods for Deep Foundations Under Static Axial Compression is justifiably general so that it has as many applications as reasonably possible. There are aspects of the test setup, the test procedures, and data interpretation for instrumented piles (some of which are specific to augered cast-in-place piles) that are either not discussed in detail in this ASTM standard or are not addressed at all. Specifically, the use of variable time hold times can obscure the shape of the conventional load-deflection curve, as well as, influence the interpretation of the ultimate pile capacity. Unload-reload cycles induce additional non-uniform internal axial loads within the pile which complicate interpretation of the strain gage data and increase the potential for errors. Attempts to maintain a constant top load during the hold period can lead to operational difficulties in taking measurements and are technically unnecessary. Residual load has been shown to develop in cast-in-place piles and can significantly influence the axial load distribution as interpreted from strain gage data. The stiffness of cast-in-place piles has been observed to vary with the measured strain, and a constant modulus, as provided by correlation with the unconfined compressive strength of the grout, may lead to a significantly different interpretation of the axial load distribution.

Jan 1, 2010

By D. Akers, R. Dospoy

Introduction The geological processes that form coal can also concentrate trace elements in the coal. For example, the average concentration of arsenic in bituminous coal (20 ppm) is ten times the average concentration found in all the other rocks that make up the earth's crust (2 ppm). Similarly, other elements, such as antimony, cadmium, mercury and selenium, are more concentrated in coal than in the earth's crust. When coal is burned, trace elements can be further concentrated. Although no new constraints on trace clement emissions were placed on the power generation industry under the 1990 Clean Air Act Amendments, the act does mandate a three-year study of air toxics. Any new regulations aimed at electric utilities as a result of this Federally-mandated study will almost assuredly be very costly-an estimated $1 billion per year. Many trace elements in coal are associated with mineral matter. For example, arsenic is commonly associated with pyrite, cadmium with sphalerite, chromium with clay minerals, mercury with pyrite and cinnabar, nickel with millerite, pyrite and other sulfides, and selenium with lead selenide, pyrite and other sulfides (Finkelman, 1980). There are also cases in which some of these elements are organically bound. Just as both organic and pyritic sulfur can be found in the same coal, the same trace element may be both organically bound and present as part of a mineral in the sane coal. Physical coal cleaning techniques are effective in removing mineral matter from coal and can potentially remove at least some of the trace elements associated with specific minerals, thereby reducing the release of these elements into the atmosphere. Conventional coal cleaning to remove trace elements As part of a project funded by the Electric Power Research Institute, CQ Inc., a wholly-owned EPRI subsidiary located in western Pennsylvania, has demonstrated that large reductions in the concentration of many trace elements are possible if conventional coal cleaning techniques are properly applied. Four examples are given in Tables 1 to 4. In each example, the results shown were generated by cleaning the coal at CQ Inc.'s commercial-scale cleaning test facility. Cleaning results for Upper Freeport Seam coal from Northern Appalachia are provided in Table 1. Data are presented in the table in two ways: as a weight-based concentration (parts per million) and as a concentration per heat unit (grams per billion Btu). Grams per billion Btu is analogous to pounds per million Btu, but avoids the use of numbers with many decimal places. The heat-based concentration provides a better measure of boiler impacts, because the increased heating value obtained through coal cleaning reduces the number of tons that must be burned to produce a given thermal output. Reducing the quantity of coal burned reduces the quantity of trace elements entering the boiler. This raw coal is relatively high in several trace elements of environmental concern, including arsenic, cadmium and chromium. Cleaning provided large reductions in the quantity of arsenic, barium, cadmium, chromium, fluorine, lead, mercury, nickel, silver and zinc. The results for tests with a Powder River Basin coal, Rosebud/McKay, are presented in Table 2. Large reductions in arsenic, barium, cadmium, fluorine, mercury, nickel, selenium and zinc were observed with cleaning. The concentration of chromium increased with cleaning, while lead concentration increased in one test and decreased in another. Table 3 presents test results for Croweburg Seam coal from Oklahoma. Large reductions in arsenic, barium, cadmium, chromium and zinc were obtained with cleaning. Smaller reductions were obtained with lead and nickel, while chromium, fluorine and mercury increased in at least one of the tests. Table 4 presents cleaning test data for Kentucky No.11 Seam coal. In this case, large reductions were obtained with all elements measured. In general, these data indicate that physical coal cleaning is effective in reducing the concentration of many trace elements, especially if they are present in the coal at relatively high concentrations. The degree of reduction achieved is coal-specific, relating in part to the degree of mineral association of the specific trace element and the degree of liberation of the trace element-bearing mineral. The extent of trace element removal also depends on the method of cleaning the coal. Figure 1 is a washability plot, by size fraction, of arsenic vs. ash content for Upper Freeport

Jan 1, 1994

By F. H. Samuel, J. E. Gruzleski, S. Valtierra, H. W. Doty, F. J. Tavitas-Medrano

319-type cast Al-Si-Cu-Mg alloys are commercially important due to their popular use in automotive applications. Artificial aging heat treatments are commonly performed in these alloys to achieve precipitation hardening and, therefore, improve their mechanical properties. The present work was carried out to investigate the effect of conventional (at a constant temperature, as specified by the standard T6 heat treatment regime), and non-conventional multi-temperature and interrupted aging cycles on the hardness, tensile and impact properties of two 319-type alloys (with and without Sr+ Mg additions). The results show that certain multi-temperature aging cycles have a more favourable effect in improving some mechanical properties than conventional cycles.

Jan 1, 2006

By Robert Kimutis, Lihong Zhou, Mark Mazzella, Jim Addis

Due to the surge in shale gas production, a substantial number of unconventional shale gas wells have been drilled across U.S. coal reserves. Gas breaches resulting from damaged wells pose a considerable safety risk to miners. This paper investigates how a ventilation system can effectively manage breached gas through a network-based numerical model and laboratory-scaled physical model. Several hypothetical gas breach scenarios in a longwall area are simulated, exploring factors influencing gas mitigation. The study establishes correlations between breached gas inflow and gas concentration at critical locations. The findings in this study provide valuable insights for managing mine ventilation systems and enhancing coal miner safety.

Feb 1, 2025

By C. H. Wayman, D. W. Fuerstenau

The effect of bubble size and concentration of certain reagents on the terminal velocity, shape, path, and drag coefficients of single air bubbles in distilled water has been investigated. Bubbles of a certain size range rise considerably faster than Reynolds number-drag coefficient relationships predict, whereas a small amount of frothing agent reduces their terminal velocity. The rapid velocity at which bubbles rise in distilled water appears to result from slip at the boundary and from circulation within the bubbles. Surface-active agents retard bubble motion through prevention of both circulation and slip at the boundary. A surface tension concentration gradient helps maintain bubble sphericity. HE gas phase is one of the indispensible in-gredients in flotation operations. Flotation depends on the collision of an air bubble and a mineral particle in a pulp and their ability to remain in contact long enough for adherence to take place. Before it is possible to understand the mechanics of air bubble-mineral particle encounter, it is necessary to learn more about the nature of bubbles themselves before collision with a mineral particle has taken place. To date, little work has been done on air bubbles in flotation systems. In 1945 Fahren-wald' presented a study of the role of frothers on air bubbles and on aeration in flotation, and recently Wark and Sutherland' discussed the work of Rosenberg- in relation to flotation. The research reported in this present article was undertaken to investigate systematically the effect of bubble size and the concentration of certain reagents on the terminal velocity, shape, path, and drag coefficient of single bubbles in distilled water. Most of the work is concerned with the effect of a-terpineol on bubble motion in water, but studies were made with potassium chloride, potassium hydroxide, potassium ethyl xanthate, and potassium amyl xanthate. Experimental Method and Materials: To obtain free bubble rise and reduce wall and surface effects, the investigators used a tank of 5½x5½x30-in. internal dimensions, filled with water to within 4 % in. of the top.' The tank was made of acrylic plastic so that the walls would have good optical properties. Distilled water, which was re-distilled in a block tin still and saturated with air before each test, was used in all the experiments. All solutions were made with reagent-grade chemicals. During each experiment the water was at room temperature, and during the course of an experiment the temperature did not fluctuate more than 0.5°C. Since the experiments were performed over a period of six months, the temperature varied between 25° and 27°C. The temperature at which each series of experiments was conducted is recorded with the data. The experimental apparatus is presented dia-grammatically in Fig. l. Individual air bubbles were generated from purified compressed air through a capillary of 0.003-cm internal diameter at a rate

Jan 1, 1959

By Francis Wm. Gray

The preparation of a paper read before this Society in 1927 on Undersea Mining led to representations to the Deputy Minister of Mines at Ottawa, Dr. Chas. Camsell, and to the Director of the Geological Survey and the Director of the Mines Branch, which resulted in the undertaking by these bodies of a geological, physical, and chemical survey of the Sydney coalfield, combined with revision of the geological maps, on all of which much progress has been made. Preliminary studies revealed the necessity for a new base-map on a scale that would permit the representation of the whole coalfield from cape Dauphin to Mira bay on one sheet, and in the making of this map the Geodetic and Topographical Surveys have collaborated, with the assistance of airplane surveys for filling-in of detail. The new map will show all the data accumulated by 50 years of active mining and will show also the extent of mine workings, with level-contours under the sea. Dr. W. A. Bell, of the Geological Survey, has, over a number of seasons, studied in the field the historical geology with the purpose of elucidating the sequence of earth movements that have determined the structure of the coalfields, especially those that have governed the course and extent of the complementary folds that traverse the Sydney coalfield. Dr. B. R. MacKay, of the Survey, and the officers of the Fuel Testing Laboratories at Ottawa have made exhaustive studies of the Phalen seam, chemical and microscopic, intended to elucidate the conditions under which this seam was deposited, and some very interesting conclusions have been reached.

Jan 1, 1934

By Ben Bowman

For certain ferroalloy furnaces, such as ferrochrome or ferromanganese, there is still doubt about the mechanisms operating under the electrode tips. In this paper a model is built that does not call upon an arc. The medium is best described as an electrically conducting slurry, a mixture of liquids, solids and gas. There are two sources of propulsion, the Lorentz force within the conducting part and buoyancy generated by CO bubbles, creating two opposed poloidal circulation loops, downward below the electrode axis and upward further out.

Jan 1, 2014

By A G. Sheard

Fire safety requirements inside tunnels have become more demanding as tunnel designers consider the impact of potentially larger fires. Tunnel ventilation equipment is required to clear hot gases in the event of a fire. This is vital to maintain smoke free escape routes for people trapped in the tunnel and to facilitate safe access for emergency services. As the fire becomes larger, the temperature of clearing hot gases increases. Traditionally, engineers have taken into consideration gas temperatures of 250°C when designing tunnels. Because of larger fires, engineers must now design equipment to clear hot gas up to 400°C.Increasing the temperature of hot gases to 400°C requires tunnel ventilation equipment that goes beyond historic limits. As temperature rises, material strength reduces, consequently mechanically constraining fan aerodynamic performance. Developing tunnel ventilation equipment suitable for clearing hot gases at 400°C requires a fan technology that is more typical of industrial turbomachinery. The standards EN 12101-3:2002 and ISO 21927-3:2006 defi ne the necessary design criteria and testing methodologies to verify that a range of tunnel ventilation equipment is capable of extracting hot gases.This paper describes the process by which the authors certified in accordance with EN 12101-3 and International Organization for Standardization (ISO) 21927-3 a range of powered ventilators suitable for clearing smoke and hot gases at 400°C for two hours. Proving the high temperature capability of the new range provided a challenge as a consequence of the large physical sizes and high motor powers involved. Additionally, the need to install vertically, as well as horizontally, imposed high thrust loads on motor bearings, further complicating both mechanical design and testing. The paper presents the methods by which the authors overcame these challenges.

Mar 8, 2011

By R. W. M. Lai

In flotation or hydrometallurgical leaching of minerals, the cumulative metals recovery for a given process condition generally approaches a maximum value or an asymptote as the process time increases. This paper discusses the experimental methods of identifying and obtaining the asymptote of metals recovery through kinetic studies. In flotation, the kinetic asymptote of metal recovery, or ultimate recovery, is a function of grinding and collector dosage, but within a realistic variable range, is not a function of pH or temperature. However, variations in grinding, collector dosage, pH and temperature, all exert noticeable effects on flotation kinetics. Frothers generally have a minor affect on the asymptote, but have a major affect on flotation kinetics. The asymptote from batch flotation is found to be identical to that of a continuous flotation. In hydrometallurgical Leaching, the asymptote of metal recovery for a given leaching system is a function of such variables as temperature, particle size, and acid concentration.

Jan 1, 1983

By Geoff Whebell, Dianne Coulthard

Sampling studies of high silver (+70%), gold dore led to the development of mine site sampling techniques and superintend­ing for the collection of samples for assay and bullion weights for settlement of shipped material. Data is presented which con­firms the reliability of the procedures against the traditional remelting and sampling at the refinery. The advantages to both mine and refiner are significant and are discussed.

Jan 1, 1998

By G. Nino de Guzman, L. C. Woollacott

The isotherms that are usually taken to represent the force 'driving' the adsorption in carbon-in-pulp processes may change from contactor to contactor. This paper reports on an investigation into the extent to which this Isotherm shift is Influenced by the changes in oxygen and cyanide concentration that occur in operating plants. The impact of the isotherm shift on the reliability of simulation results is examined.

Jan 1, 1993

By Tom Bruington

This paper discusses the accuracy of determining the quantities of gold and silver on activated carbon in various stages of process for typical precious metals flowsheets. Accurate plant performance evaluation depends upon reliable estimates of carbon and precious metals inventories. The sources of sampling error are identified and methods of reducing them discussed. Several case studies illustrating the sensitivity of flowsheet performance to sampling error are presented.

Jan 1, 1991

By Brent Blanchard

As most veterans of our industry are aware, explosive demolition by its very nature is often a challenging proposition. Even under the best of circumstances, proper planning and care must be taken during a variety of processes to ensure a safe, successful result. However, every now and then a project suddenly arises where safety, timing and cost factors combine to form a critical scenario requiring rapid execution in an environment far more challenging than the norm. On these occasions, the stresses, complications - and most notably the dangers - related to the industry increase exponentially, and conspire to test the mettle of even the most seasoned experts.

Jan 1, 2003

By S K. Michelic, M Schickbichler, A Kharicha, E Karimi-Sibaki

The requirements for the controllability of metallurgical processes are increasingly becoming the focus of both industry and research. Advances in this field of research not only impact the stability of processes but often also influence the quality of the final product. One important way to examine processes in-depth, and thus show potential for improvement, is to describe them using physicsdriven models. In metallurgy, thermodynamic and kinetic descriptions of interactions between individual components of a system are often used to describe and analyse important metallurgical phenomena across the entire process. However, for the creation of physics-based models, boundary conditions and process variables must be implemented to enable a description that is as realistic as possible. The collection and generalisation of boundary conditions and process variables is, therefore, an important step towards functional models. The focus of this study is the determination of mass transfer coefficients between all components in a steel/slag/refractory system. For this purpose, experimental and theoretical methods are applied. Laboratory scale experiments are carried out in an induction furnace, and the mass transfer coefficients of the defined steel/slag/refractory system are calculated from changes in the chemical composition of the various components. Additionally, a calculation of the mass transfer coefficients based on dimensionless quantities is carried out. By comparing the values of the mass transfer coefficients determined theoretically and those determined experimentally in the trials, the suitability of the calculation is examined. The collection of mass transfer coefficients provides essential findings for future kinetic descriptions of inclusion modification based on the effective equilibrium reaction zone (EERZ) approach.

Aug 21, 2024

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the thirteenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The description of the deposits developed is followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By Ralph H. Nafziger

The feasibility of smelting a Ni-Co-Cr-bearing laterite ore from southern Oregon was evaluated by the Bureau of Mines. The objective was to prepare a master alloy for subsequent stainless steel production. A mixture of the ore with suitable reductants and fluxes was smelted in a 50-lb-capacity single-phase ac electric furnace under sub- merged arc conditions. The smelting tests produced a metal in which most of the nickel was concentrated. High-chromium recoveries required an excess of carbon. The resulting metal alloys contain sufficient nickel for some stainless steels. Ferrochromium additions would be required to attain suitable chromium levels. This research was conducted under the Oregon Metals Initiative in cooperation with Walter B. Freeman.

Jan 1, 1993

By Byron E. Eldred

(Pittsburg Meeting. March, 1010.) GENERALLY speaking, the practical study of combustion has been made mainly from the stand-point of the steam engineer. This. narrow view-point has left open a large field for scientific research on the application of combustion in other arts, where the conditions of heat-utilization are widely different from those presented in the steam-generator. The great economic importance of the boiler and the ease of measuring its performance, together with the comparative uniformity of conditions in the steam-generator, is, probably, quite largely responsible for the practical neglect of the study of the use of fuels in other arts save only on the basis of their thermal value. Yet these other arts show quite plainly that a thermal-value basis alone is Dot sufficient. For example, in burning lime, under ordinary conditions of firing, a cord of wood will do as much work as a ton of coal, though the latter affords more than twice the number of heat-units. Similar results are evidenced in burning brick, in the roasting of certain ores, in reheating billets, and in many other arts where heat is to be applied over extended areas to fragmental masses of more or less refractory materials. In these arts much is to be gained by a careful study of the application of the heating-agent in the form of the long flame, and in the production of the heat in contact with, or in direct proximity to, the object to be heated. Of necessity, in boiler-practice, combustion cannot be maintained in actual contact with, or in close proximity to, the object to be heated. Speaking in a general way, heat is imparted from burning bodies to things to be heated in two ways : directly, by radiation, and indirectly, by transfer of the sensible heat of hot gases by convection or contact; by conduction from the hot uses. Both ways are utilized in boiler-practice-directly, by

Jun 1, 1910

By T Raynlyn, S Hapugoda, V Nunna

The predominant phase in most Marra Mamba, channel iron deposits and detrital iron ore deposits is goethite. Goethite abundant iron ore fines tend to have complex mineralogical associations and fine dissemination of gangue material. These ores are typically challenging to process using conventional beneficiation methods. With declining ore grades, there is a need to develop new processing routes for low-grade goethitic ores/fines.Comparative process amenability studies were carried out using two different processing options to recover iron with low alumina and silica content from a low-grade goethite-abundant iron ore fines (-2 mm) sample from the Pilbara region of Western Australia. The first option involved dehydroxylation at 350°C and 400°C, followed by grinding dehydroxylated samples to 100 per cent passing 106 µm and magnetic separation. The second option was processing raw sample by gravity separation using a Floatex density separator. The performances of the two processes are discussed in terms of the iron grade-recovery responses, and an optimal processing route is proposed based on the findings from these tests.CITATION:Nunna, V, Hapugoda, S and Raynlyn, T, 2015. Process amenability studies on goethite-abundant iron ore fines, in Proceedings Iron Ore 2015, pp 165–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Kevin J. Ashley

Coal is deposited at a mine site in several thin seams which outcrop in rolling hills and dip at about 8° to the northeast. The deposit is located in the northeast area of the State of New Mexico in the Southwest of the United States. A drilling program was undertaken and was quite irregular. Not all of the seams appear in all of the drill holes. Some of the holes did not go deep enough, while others were drilled below the outcrop of some seams. Occasionally a seam would pinch out and not be seen in a drill hole. Also, the outcrops of the seams are buried in many places by several feet of alluvium. All of these factors make correlation of the seams between drill holes difficult. The drawing of cross sections in three directions and at many locations across the mining area have been necessary to assure the accuracy of the input data.

Jan 1, 1982

By A. F. Colombo, R. T. Sorensen, D. W. Frommer

The Bureau of Mines developed a flotation method for concentrating spiral tailing produced from pilot plant tests on the Champion mine ore fines . The feed material contained about 49 percent Fe and 15 percent SiO2 and was posed mostly of specular hematite , muscovite , and chlorite . Bench- scale , batch flotation research developed a reagent suite composed of tall oil - fatty acid , fuel oil , sulfuric acid , sodium fluoride , and sodium silicate for recovery of iron minerals in the froth product . Concentrate made with the reagent suite contained 87.3 percent of the iron and analyzed 65.6 percent Fe and 1.9 percent SiO2 . Continuous flotation tests were made with a nominal feed rate of 400 lb /hr , but without middling recirculation . Using nearly the same amount and complement of reagents as in the batch tests , three similar continuous tests gave concentrates averaging 63.9 percent Fe and 3.1 percent Sio while recovering about 86 percent of the iron .

Jan 1, 1964