Search Documents

By S. Managi, M. C. Williams, N. H. Behling

Particle processing is a key to using solid particles in fuel cell applications. Selectivity with regard to reactivity, impurities, etc. is important feature and the treatment of particle surfaces could greatly impact the performance of direct carbon fuel cells. Solid fuel particles will become increasingly important in the future. Present energy conversion systems for solid fuels are too inefficient. New energy conversion systems for solid fuels with higher energy conversion efficiencies are possible. Fuel cell technology is a key-technology in these new conversion systems. The direct carbon fuel cell (DCFC) operates on carbon particles obtained from a variety of solid fuel feedstocks. The DCFC is the only fuel cell designed to directly oxidize carbon particles in a special anode chamber. The particles are generally graphite structure with high purity. The electrolyte used is the high temperature solid oxide, molten carbonate or hydroxide electrolyte. Since a pure stream of CO2 is produced the stream can easily be sequestered and disposed. Pure carbon dioxide produced as a by-product would also have a market in many industries. A well-defined technology roadmap identifying key research and development (R&D) issues is necessary to provide a framework for the development of these systems and to prevent entrenchment in inherently inefficient technologies. This review paper describes the direct carbon fuel cell and its system, how it works, the developmental status, the characteristics of the carbon particles needed, and the research and development issues for the technology. INTRODUCTION The DCFC has been under development for many years. It was researched as early as 18961), but an intense research and development is necessary to realize its potential. William W Jacques, a US electrical engineer and chemist, described a DCFC in 1896 in US Patent 555511 for a “Method of converting potential energy of carbon into electrical energy”. Jacques used coke electrodes in a molten NaOH electrolyte. Molten carbonate fuel cell (MCFC), solid oxide (SOFC) or hydroxide electrolyte (AFC) technologies can be used as the basis for the DCFC technology. A schematic of the direct carbon fuel cell in the MCFC mode is shown in Figure 1. The molten carbonate fuel cell operates at approximately 650°C (1200°F). The high operating temperature is needed to achievesufficient conductivity of the carbonate electrolyte, yet allow the use of low-cost metal cell components. A benefit associated with this high temperature is that noble metal catalysts are not required for the cell electrochemical oxidation and reduction processes. For the hydrogen reaction the half-cell electrochemical reactions are

Jan 1, 2019

By C. E. Saxon, F. E. Cash

"Adequate lighting for all mining operations would unquestionably tend to promote both safety and efficiency; this would be true not only for men but also for the animals that man impresses into service in mines. The Markeeta Coal Co. and the Alabama Fuel & Iron Co. both operating mines in Alabama, have found that equipping mine mules with portable electric lights is more efficient, much more humane, and far more safe for both men and animals then the more or less usual method of forcing the animal to do its work essentially in darkness.This report is intended to give the mining industry data, that will aid in trying to bring about safe and efficient operation of mines.The authors desire to thank Charles F. DeBardeleben, president, Fred R. Bell, general manager, Hewett Smith, C. H. Shepherd, and R. A. Sensing, superintendents for the Alabama Fuel & Iron Co.; and Charles F. DeBardeleben, Jr., president, and H. M. House, superintendent for the Markeeta Coal Co., for their cooperation in furnishing the data for this paper.The eight mines operated by the Alabama Fuel & Iron Co. and one operated by the Markeeta Coal Co. in Jefferson and St. Clair Counties, Ala., are the only mines in Alabama where mules are provided with portable electric lights, and there are few if any mines in other States in which this system is in use.These two companies are convinced that equipping all mine mules with good lights decreases underground haulage cost by animals by prolonging the useful life of the animals, increasing their efficiency, lessening haulage wrecks and delays on haulage, and increasing production. Last but not least of the advantages would be the more humane treatment of the animals.The nine mines are developed by slopes along the dip of the coal bed, with double-room entries on 200- to 300-foot centers turned right and left off the slopes and with approximately 1 per cent grade in favor of the loads. Rooms are driven up or diagonally up the pitch from these entries.A surface hoist delivers the empties from the surface to the entry sidetracks at the slope and pulls the loads to the surface. From these sidetracks, mules pull one to four wooden cars, each of which holds 1-1/2 to 2-1/2 tons of coal, deliver the empties to the rooms and entry faces, and pull the loads to the slope sidetracks. The mule haul varies from 100 to 3,000 feet; there are no locomotives or trolley wires in any of these nine mines, seven of which are rated as gassy and two as nongassy by the Alabama state Mining Department."

May 1, 1933

By Theo Lehner

The Rönnskär smelter has wide experience in the field of recycling of non-ferrous metals. Today, smelting and refining from primary and secondary raw materials are integrated in a complex flow sheet. Boliden operates a lead flash smelter, a lead refinery, a copper smelter and refinery, a sulphuric acid and sulphur dioxide plant, a slag fuming plant and precious metal plant at its Rönnskär smelter in the North of Sweden. The Business Area Smelter Operations also incorporates Boliden Bergsöe, Sweden's lead-acid battery recycler, and Norzink, Norway, where recycled zinc accounts for more than 20% of it's production. Raw materials for the Rönnskär smelter include concentrates, ashes, slags, metallic scrap, electronic scrap and electric arc furnace (EAF) steel-making dust. This paper briefly describes current operations and illustrates current measures to improve productivity. Limits to recycling as experienced by a non-ferrous smelter are, illustrated. The deportment of critical elements contained in raw materials is also discussed.

Jan 1, 1998

By P. Rusin

Many oxide silver and molybdenum deposits remain undeveloped because chemical extraction yields poor recoveries or is environ-mentally unacceptable. Bio-reductive leaching of such ore samples at MBX resulted in high recoveries of silver and molybdenum. When baseline 3-day cyanide bottle roll tests were conducted on manganiferous oxide silver ore, 13.7% of the silver was extracted. In contrast, 86% of the silver was microbially solubilized into the organic growth medium by bio-reduction with 99.8% dissolution of manganese. A follow-up cyanide bottle roll test yielded an additional 8.5% silver recovery for a total recovery of 94.5%. Baseline 3-day acid bottle roll tests of the iron oxide molybdenum ore yielded 1.8% moly. However, bio-reduction solubilized 93.3% of the moly into the growth medium. An additional 0.3% moly was recovered during the follow-up acid bottle roll test. Microbial treatment of refractory oxide ores with bio-reductive bacteria resulted in higher recoveries of silver and molybdenum than conventional chemical leaching. The bioleaching process occurred at a near-neutral pH at ambient temperatures. The bacterial solubilization of silver and moly was achieved without the use of cyanide or sulfuric acid.

Jan 1, 1992

By O. Tranbarger

In aging tunnels, wall and roof deterioration can eventually result in defects that must be detected and repaired to maintain safe structural conditions. In investigating tunnel defect conditions, a specialized FM radar system was developed with a programmable VHF and UHF operating sweep range for optimizing the penetration and measurement capabilities. The new FM radar technology was tested in two aging brick-lined tunnels in New York City. Test results showed that FM radar signals could penetrate eight courses of water-saturated brick and that the original steel liner outside the tunnel walls was intact.

Jan 1, 1985

By George S. Rice

In response to numerous requests for information as to the status of internal-combustion mine locomotives of the Diesel type that use heavy or nonvolatile oil for fuel, with special reference to their safe use in coal mines, the United States Bureau of Mines is issuing this t port. Data were obtained on application of such locomotives to coal mining only in Belgium, France, Germany, and Great Britain. The locomotives are used in coal mining in other countries, as well as in potash, iron, and other kinds of mining, but their chief development has been in coal mining in Germany, France, and Belgium. Recently popular interest in the Diesel type of engine for motive purposes was aroused in this country by the successful application of Diesel engines to railroad locomotives hauling fast transcontinental trains, and, according to published statements, at a low cost of fuel per mile of run.

Jan 1, 1936

By A. Y. Senchenko, Y. V. Kulikov

"In recent decades HPGR technology has proven itself in comminution circuits of mining plants. High technical and economic performance, lower specific energy consumption and reliability of HPGR equipment makes it an efficient alternative to conventional circuits using stage crushing and rod/ball milling, as well as to AG/SAG circuits. However, despite all the advantages of this technology the correct selection of key and auxiliary equipment is very important since errors at testing and design stages may lead to discrediting of the whole concept of HPGR application. There is a great variety of possible circuit configurations using HPGR, e.g. with circulation of edge product, with crushing of the whole discharge and circulation of screen oversize, successive two-stage crushing, etc. Each type of minerals will require its own optimal crushing circuit. In this context the testing methodology for selection of an optimal configuration becomes of prime importance. It is common knowledge that the best simulation of material crushing and softening within a HPGR can be obtained only in the course of a large-scale pilot test. The main approaches applied to this kind of testworks are described in this article. Special aspects of HPGR technology design and industrial operation are revealed as well. Some operational issues of HPGR equipment and of circuit as a whole were detected. They are related to regions specifics, plants location, and other factors. Process solutions proposed to deal with these issues are also indicated in the article. INTRODUCTIONDesign and construction of the processing plants involving High Pressure Grinding Rolls (HPGR) technology becomes more and more common in mining as this technology has specific technical and economic advantages against the circuits with autogenous/semiautogenous mills (AG/SAG) and other circuits. The main advantage of the technology is low energy consumption and low operation costs respectively. The presence of microcracks and increased content of fine size fractions in the crushed product contribute to reduction of energy required for further ball grinding. Besides, HPGR technology applies a special wear resistant liner that enables significant reduction of operation costs of grinding media and liner comparing with AG/SAG circuits."

Jan 1, 2016

By S. Kittel, P. Galleguillos, H. E. Urtubia

The rougher flotation at Escondida consists of 80 cells of 100 m3 each, with injected air. Escondida has developed a system of automatic control of the rougher flotation using video cameras, which have been operating since 1997 for remote monitoring and manual control. Since 1999, an image processing software and a group of rules have allowed implementation of an expert system. To date, the expert system controls the superficial speed of each cell by adjusting the air flow and the froth depth of the flotation bank. Preliminary tests of the expert control on two of the eight rows gave 1.2% higher rougher recovery at a 92% degree of confidence. The proven benefits are already sufficient to move towards a complete plant implementation.

Jan 1, 2001

By Henry T. Miller

INTRODUCTION The basic purpose of this paper is to suggest procedures and practices to insure that no employee working in a uranium milling operation receives exposure to radioactive, toxic, or other materials or agents that might produce a permanent, deleterious effect upon his physical health and well-being. This program is also designed to insure that each employee can carry out his assigned duties without risk to his health or to that of his fellow workers. The assumptions underlying this program are by necessity, conservative, with emphasis being placed upon prevention rather than correction or reaction to an undesirable situation. The limits specified-either as Threshold Limit Values (TLVs), Maximum Permissible Concentrations (MPCs), or Radiation Protection Guides (RPGs)--represent both standards of best practice and those of law and regulation. The total program is envisioned as a balanced combination of occupational hygiene and radiation monitoring. This includes surveying, air sampling, personnel dosimetry, bioassay, medical surveillance, epidemiology, and training--all backed by a thoroughly tested and evaluated set of emergency procedures. The program, as presented, is keyed to the results of monitoring, surveying, air sampling, medical surveillance, and epidemiology--it being obvious that no problem can result when no hazard can be identified. The lack of an identified hazard, however, does not negate the need for such a program and prudence suggests the need for routine surveillance programs in the best-designed facility. [The Model Mill] The model mill used in this paper is that presented by the U. S. Environmental Protection Agency in its study of the uranium fuel cycle1. The model mill processes 600,000 metric tons of ore per year into 1,140 metric tons of U308 as yellowcake per year using an acid leach process. Other characteristics of the mill such as location, tailings dam design, number of light water reactors supported, and geographical location are not pertinent to this paper. The usual remote western location of these facilities produce some difficulties in delivering the required occupational medical services and is not within the scope of this paper. The operating lifetime of most mills is commonly estimated as from 12 to 15 years in actual practice; however, the U. S. Environmental Protection Agency estimated a 20-year lifetime for its model. The principal steps in the acid leach process include :2 (a) Ore is blended and crushed to pass through a 2.5 cm (one inch) screen. The crushed ore is then wet ground in a rod or ball mill and is transferred as a slurry to leaching tanks. (b) The ore is contacted with sulfuric acid solution and an oxidizing reagent to leach uranium from the ore. The product liquor is pumped to the solvent-extraction circuit while the washed residues (tailings) are sent to the tailings pond or pile. (c) Solvent extraction is used to purify and concentrate the uranium. (d) The uranium is precipitated with ammonia and transferred as a slurry. (e) Thickening and centrifuging are used to separate the uranium concentrate from residual liquids. (f) The concentrate is calcined and pulverized. (g) The concentrate or yellowcake is packaged in 208 liter drums for shipment. This process is illustrated in Figure 1.3

Jan 1, 1981

By Mark Hollingworth

"There is general consensus that as the world continues to change at an ever-increasing pace, companies must continually adapt their operations in order to remain competitive. Those that change fast enough, survive; those that don’t, perish quickly. Today, we hear that it is not worth the time preparing corporate business plans as they are out-of-date before the ink is dry. Within the corporate environment of the 1990s, we must “think” strategically, be a “learning organization”, keep our costs low, focus on our core competencies, stay as flexible as possible and create value. So-called “sustainable competitive advantages” can be obsolete before a patent is issued — if its even worthwhile patenting the advancement. This is industry in the 1990s.Now, while all this radical change has been underway in the global industrial environment, what have Canada’s universities been doing to keep pace with the change affecting one of their major stakeholders? Have they adapted their products and services to suit the new market conditions? Have they built closer links to industry to try to understand how better to serve this important client? Do they welcome industry input as to how to redefine their mission, objectives, strategies or their course contents? Do their students graduate with skills ideally tailored for the global mining industry? In the era of communication, can they write high quality reports in English, never mind speak French or Spanish?In an effort to provide Canada’s engineering faculties with a “blueprint” for the future, the Canadian Academy of Engineering pre-pared a report entitled “Engineering Education in Canadian Universities”, published in August1993, which concluded with the following recommendations:"

Jan 1, 1996

Discussion of the papers with a written contribution and authors' written replies.

Jan 1, 1947

By Dippenaar R, Evans T

Twin-roll continuous casting technology is rapidly approaching commercialisation. Fundamentally different than conventional continuous casting, heat transfer and hence solidification during twin-roll casting are governed by the interfacial melt/mould thermal resistance, as opposed to the resistance of the solidifying shell. Under these conditions the interface resistance is predominantly controlled by the melt/substrate wetting behaviour. The very early stages of melt/mould contact are characterised by highly transient heat transfer conditions. The overall melt cooling rates prior to the formation of the first solid are reported to be in the range of 1000 - 50000 K/s with melt undercoolings of up to 300 K. At the points of intimate melt/mould contact the thermal resistance is approaching zero, where cooling rates and undercooling much larger than those reported in the literature are probably occurring. Improved wetting will reduce the energy barrier for nucleation while at the same time increasing the cooling rate of the liquid. Since the overall nucleation rate is controlled both by the rate of cluster formation and the rate of atom transfer to the nucleus, a critical cooling rate will exist above which the nucleation rate is expected to be reduced. Under these conditions, it is possible that the first solid phase to form is a metastable glass which subsequently transforms into a crystalline phase. The implications on nucleation and early growth are also discussed.

Jan 1, 1999

By Galen Clevenger

THE losses of gold and silver occurring during the conversion of the precipitate, resulting from the cyanide process, into bullion may occur in two ways: first, there may be mechanical losses during the handling of the precipitate up to the time that it is charged into the melting furnace; and second, there may be losses after the precipitate reaches the melting furnace. Much of the loss during the handling of the pre-cipitate can be eliminated, and in fact, in modern plants this loss is known to be very small; particularly since preliminary acid treatment of the precipitate with the attendant extra operations has been abandoned in all but certain plants where gold predominates and this extra step is still deemed necessary. The losses in the melting furnace are from dusting and volatilization; losses in the furnace bottom and linings; floor sweepings; and slag and matte. The gold and silver in the: products which do not: go out of the flue are readily recoverable by standard methods, and while there may be considerable gold and silver tied up at times, the ultimate loss with careful "work should be small. The losses resulting from volatilization and dusting in connection with the melting of the silver slime from copper refineries have been determined by standard methods, and the possible recovery: definitely estab-lished through the installation and operation of electro-static precipitation units. This subject has not been thoroughly investigated in connection with the melting of`. cyanide precipitate; at least, there are no published accounts of such tests. Experiments have been made in the past to determine melting losses by weighing and assaying the precipitate, but this method gives results which are uncertain on account of the difficulty of accurately sampling and assaying cyanide precipitate. Attempts to ascertain these losses by bubbling a measured sample of the gas through cyanide solution or, other absorbent have likewise failed to give depend-able results.

Jan 1, 1922

By James Pirie

"The major Archean gold deposits in the Red Lake greenstone belt, which have produced over 374 million grams of gold since 1930, occur near the top of the lower komatiitic to tholeiitic mafic to ultramafic metavolcanic sequence. The upper calc-alkalic mafic to felsic rocks form three discrete and separate ediftces overlymg this lower sequence.The gold deposits are classified according to their stratigraphic or lithologic associations into:1) mafic-volcanic-hosted deposits;2) felsic-intrusive-hosted deposits; and3) stratabound deposits.Group 1 and to a lesser extent Group 2 deposits occur within zones of alteration several square kilometres in extent. The nature of this pervasive alteration can be characterized by comparison of petrochemical data from the altered rocks and their fresher equivalents some distance away. The altered rocks have substantial addition of SiO2> CO2, K2O, As and Sb and subtraction of Na20, CaO, MgO and total Fe. Cr, Ni, Co and Zr appear to have been relatively immobile. Hydrothermal alteration and gold deposition probably accompanied early fumarolic activity and continued during subsequent deformation the metavolcanic sequence, with gold eventually being mobtltzed and concentrated into major vein structures to form the present orebodies. The smaller Group 2 deposits formed by emplacement of felsic intrusions into already altered, anomalously gold-bearing mafic metavolcanics, with the heat from the intrusions setting up parasitic hydrothermal systems which mobilized the gold and deposited it along with minor sulphides in fractures in the cooling intrusions."

Jan 1, 1982

By M. J. Ferrante

The standard enthalpy of formation, low-temperature heat capacities, and enthalpy increments above 298 K were determined by the Federal Bureau of Mines for synthetic dawsonite [NaA1C03(OH)21. The enthalpy of formation was determined by hydrochloric acid solution calorimetry, with the result ?Hf°298 = -469.4±0.7 kcal/mole. The low-temperature heat capacities were determined from 6 to 307 K by adiabatic calorimetry. Tabulated are low-temperature values of Cp°, S°, and H.-Ho° from 3 to 298 K. The derived entropy at 298 K is S298 = 31.55±0.3 cal/deg mole. Enthalpy increments above 298 K were obtained by copper-block drop calorimetry. Tabular data of Cp°, S°, H°-H°298, -(G°-H°298)/T, ?Hf°, ?Gf°, and log Kf are given from 298 to 477 K. Enthalpies and Gibbs energies of decomposition are also reported.

Jan 1, 1976

By Michelle Mouton, Johanna van Deventer, Jussi Vaarno

Mintek has been involved in numerous projects to remove Fe and Mn from dilute Co sulphate solutions by means of oxidative precipitation using air/SO2. Test work was done using a gas induction system, designed and supplied by Outotec. Various aspects, such as SO2 concentration, SO2 flowrate, impeller rotation speed and pH were investigated on a 2 m3 scale. Batch tests were performed using a residence time of 5 hours. Mintek has been involved in numerous projects to remove Fe and Mn from dilute Co sulphate solutions by means of oxidative precipitation using air/SO2. Test work was done using a gas induction system, designed and supplied by Outotec. Various aspects, such as SO2 concentration, SO2 flowrate, impeller rotation speed and pH were investigated on a 2 m3 scale. Batch tests were performed using a residence time of 5 hours. Impeller rotation speeds of 0-220 rpm were tested, and it seemed that speeds of between 80 and 220 rpm gave similar Fe and Mn removal rates. Co and Cu losses were generally below 1% and 5% respectively at pH 3.

Jan 1, 2007

By S. Frimpong

The cable shovel excavator is used for primary production in many surface mining operations. A major problem in shovel excavation is the variability of material diggability, resulting in varying mechanical energy input and stress loading of shovel dipper-and-tooth assembly across the working bench. This variability has a huge impact on the shovel dipper and tooth assembly in hard formations. In addition, the geometrical constraints within the working environment impose production limitations resulting in low production efficiency and high operating costs. A potential solution to the above problems is the application of an intelligent cable shovel excavation(ICSE) technology. In this paper, dynamic models of the cable shovel excavator are developed with numerical examples. These models form the basis for developing dynamic shovel simulators for an intelligent shovel excavation technology. The dynamic equations are developed using the Newton-Euler techniques. The path trajectories for efficient excavation, dynamic velocity and acceleration profiles, and dimensioned parameters for optimum feed force, torques and momentum of shovel boom-bucket assembly are modeled and used for efficient excavation. The optimum digging forces and resistances for the cable shovel excavator are modeled and used to predict optimum excavation performance.

Jan 1, 2003

By Irving H. Wentworth

The little town of San Nicolás, Tamaulipas, Mexico, lies approximately 60 miles east of Linares, situated in the State of Nuevo Leon, and 150 miles SE. of Monterey, as shown in the sketch-map, Fig. 1. The place is reached from Monterey by the Tampico train as far as Linares, a distance of 92 miles, and then by coach the rest of the way. It is situated in a narrow valley between low hills, the houses forming one main street and a plaza. It is peopled by about 500 inhabitants. The climate is temperate, the thermometer ranging from 90" in summer to a few degrees below freezing-point in winter; but this severe weather only lasts a day or two at a time, when the " northers " blow. There are no streams in the vicinity, but water sufficient for the use of the people is obtained from wells. The rainfall is about the same as that in the rest of NE. Mexico. The rainy months are July, August, and September. The rest of the year is practically dry, with an occasional showery day or two during the winter, when a " norther " is blowing. Timber is abundant in many localities. There are two varieties of oak, besides mesquite, ebony, "maguira," "patol," and a number of other kinds of trees indigenous to this region. I. History. On the discovery of the silver-lead bearing veins occurring in this district, the mining-camp of San Nicolás was founded in 1767 by the Spaniards, and numerous mines were opened and worked for a distance of about 3 miles east and 5 miles west of the town. At the western extremity and near the Car-rolefia mine, a small town called San Pedro was huilt. The

Jan 1, 1913

By Robert Linton

AT its meeting on May 21, the Board of Directors approved the recommendations submitted by President Lovejoy and named a nominating committee for the year that is especially well distributed as to major technical interest and as to geography. As may be seen from the list published herewith, two come from the East, two from the Midwest, and three from the far West. Mr. Linton, the chairman, has been a valued member of the Institute for 36 years. A memorandum drawn up by Paul D. Merica, representing the A.I.M.E., and W. R. Barclay, representing The Institute of Metals of Great Britain, setting forth a reciprocal plan for special memberships in each Institute for members of the other, was discussed. Both societies already have formally approved the plan in principle and Dr. Merica was clothed with full authority to agree on a few small details that have not been settled, and conclude the arrangement in behalf of the Institute.

Jan 1, 1936

By Oliver Bowles

It is noteworthy that 80 to 95 per cent of the gross production of all slate quarries in the United States is discarded as waste . In view of the loss involved in handling so much waste , and the consequent added cost of the finished product , the Bureau of Mines has undertaken a study of the slate industry for the purpose of devising the best means of reducing the proportion of waste , and of utilizing the unavoidable waste . The utilization of waste has received special attention , and the cooperation of many prospective purchasers of waste slate has been enlisted in testing its adaptability for various uses .

Mar 1, 1921