Search Documents

By Pierre Roy, Claude Gosselin, Maryam Sadeghi, Michel Bourassa, Christian Rochefort, Claude Bazin, Gautier Mahieu, François Lavoie, Marilène Renaud, David Cataford

"Spirals are gravity concentrators used for the concentration of iron oxide minerals from ores. This paper presents the mineral size recovery curves observed for spirals operating in two Canadian iron ore processing plants. The size recovery curves are presented for rougher, cleaner and re-cleaner spirals. The partition curves observed for the spirals are significantly different than those observed for typical gravity concentration devices such as hydrocyclones or hydraulic classifiers. The size recovery curves show the complex behaviour of the minerals as they flow down a spiral and are analysed with a view toward process modelling and simulation. Initial simulation results show that gains in the iron recovery can be achieved by increasing the recovery of coarse iron oxide particles in the rougher spirals.INTRODUCTION Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and different heavy minerals ores (Wills, 1992). The classification of the particles in spirals is based on the combination of gravity, centrifuge, drag, lift and Bagnold forces (Atasoy and Spottiswood, 1995; Burt, 1984; Bouchard, 2001). Several papers are dedicated to the analysis of the forces acting on the particles flowing down a spiral (Das and al., 2007; Sivamohan and Forssberg, 1985; Holland-Batt and Holtham, 1991; Holtham , 1992). Most of these papers aim at the development of a general model for the simulation of the classification of the particles for coal ore processing. Few papers deal with the operation of spirals for processing iron ores (Hyma and Meech, 1989; Srivastava, 2001; Dallaire et al., 1978) and fewer papers present results for spirals used as cleaners following a rougher stage. Since the classification in spiral classifiers is dependent on the particle size and specific gravity a partition or performance curve commonly applied to classifiers (Mai Manga et al., 2012) is used here to analyse spiral operation. Few papers were found to describe the operation of spirals in terms of partition curves (Atasoy and Spottiswood, 1995; Holland-Batt and Holtham, 1991; Richards et al., 2000). Most of the investigations presented the application of a model to simulate the position of coal particles of various sizes and specific gravities along the trough of a spiral (Kapur et al., 1996; Holland-Batt and Holtham, 1991). In addition most of the available literature on spirals deals with one stage of concentration by spirals (Dallaire et al., 1978; Das and al., 2007; Sivamohan and Forssberg, 1985) while industrial circuits usually consist of rougher and cleaner spirals."

Jan 1, 2014

By Dean J. A, Taube A, White A. H, Messenger P. R, Jones I. W O, Huston D. L

The 50 million tonne Mount Morgan gold-copper deposit (4.99 g/t Au, 0.72 per cent Cu) was an irregular pipe-like body of quartz and pyrite, with subordinate chalcopyrite, magnetite and gold. Mineralisation was hosted by the Middle Devonian Mine Corridor Volcanics which occur as a roof pendant within the Late Devonian Mount Morgan Tonalite. On three sides, the deposit was enclosed by a series of normal, concave, listric faults and surrounded by outward-dipping Mine Corridor Volcanics. The tonalite which bounded the western side of the deposit transgresses the domal structure with no apparent interference. A pipe of intense, texturally-destructive, quartz-sericite-chlorite ¦ pyrite underlay and partly surrounded the deposit.The volcanic setting of the deposit, its shape, metal content and associated footwall alteration are consistent with a subsea-floor replacement origin for the gold-copper mineralisation. Mineralogical studies have confirmed the deposit has been recrystallised and annealed by a thermal metamorphic event, most likely the intrusion of the Mount Morgan Tonalite. Pyrrhotite Pipe mineralisation replaces annealed massive pyrite, suggesting that it formed during retrogressive metasomatism associated with tonalite emplacement. Telluride minerals have a close association with chalcopyrite, and no evidence for a late telluride paragenetic stage was observed. Telluride mineralisation is inferred to be genetically related to the massive sulphide mineralisation, and a separate magmatogenic origin for this mineralisation is discounted.

Jan 1, 1993

By P. O. Parfitt

The Critical Path Method has proved its usefulness at Mcintyre Porcupine Mines Ltd. This paper illustrates the techniques of network construction and analysis, and the application of the method at the Mcintyre copper mine to various projects in the gold mine. C.P.M.'s use in a mill maintenance project is also discussed.

Jan 1, 1966

By M Malec, J Szczerbinski

Hazards in underground mines are concomitant with the mining of mineral deposits and have their source in a minerÆs work environment. The authors of the paper have undertaken a trial classification of these hazards into three groups, depending on the sphere of their occurrence:lithosphere, ie rock mass, atmosphere, ie air in mine workings, and technosphere, ie machines, equipment and facilities in mine workings. The lithosphere creates such hazards as bumps, rock outbursts, the atmosphere is a factor causing fires, methane explosions and climatic hazards, whereas accidents concomitant with an operation of machines and equipment occur in the technosphere. Assuming that the number of accidents in the mining industry, concomitant with hazards, reflects the degree of safety, it has been shown, that in Poland they are under control to a large extent.

Jan 1, 1999

By Herty, C. H.

The effect of temperature on the physical properties of structural materials has been the subject of many investigations during the past decade. The literature on the effect of elevated temperatures. is voluminous, and during the last four years a great deal of experimental work has been carried out on the effect of low temperatures on the impact properties of steel. For many engineering purposes it is important to know the shock resistance of steels at low atmospheric temperatures, and with the ever-developing field of refrigeration and separation of materials at low temperatures, the normal limits of atmospheric temperature have been exceeded in practice. Iron and its alloys in the unnotched condition have a high impact strength at low temperatures, but in practice variations in type of notches result either from design or accidentally through scratches and surface or internal defects. A study of notched bar impact tests is, therefore, highly important to the engineer. A survey of the literature on low temperature impact testing indicates that chemical composition, heat treatment and method of testing have been the variables which have been considered in most previous work. In only a few instances has any mention of the steel- making method been mentioned and in these the comparison was between steel-making processes and not between steel-making methods on the same process. In view of the wide variations in impact properties at room temperature, in quench and strain ageing and in grain growth of steels of identical chemical composition, (by this is meant the usual five element analysis reported), it was felt

Jan 1, 1957

By Faruk Oksuz, Dave Schiemann, Matt Trotter, Mike Padilla, Miguel Sanchez, Carmen Scalise

"Chicago’s Tunnel and Reservoir Plan (TARP) is a nearly $4.0 billion and over 30 years long program and arguably the largest and longest combined sewer tunnel and reservoir system in the world. Recently, a massive tunnel construction is underway for connection of the McCook Reservoir to the existing TARP tunnel system. Once completed in two stages in 2017 and 2019, the reservoir will hold 38 billion-liters (10 billion-gallons) of combined sewer overflows (CSO) and flood waters from the city of Chicago and over 20 communities in Cook County, Illinois. McCook Main Tunnel will connect Chicago TARP’s Mainstream Tunnel to the McCook Reservoir. Connecting two 10-meter (33-ft) diameter tunnels at 92 meters (300 feet) underground has not been a simple task for the McCook Tunnel Project participants, the project owner U.S. Army Corps of Engineers (USACE), local sponsor Metropolitan Water Reclamation District (MWRD) of Greater Chicago, designer Black & Veatch, and the contractor, Kiewit Infrastructure Company (Kiewit). Yet alone excavating and lining massive size tunnels, the team is also challenged with live tunnel conditions in TARP Mainstream Tunnel that carries CSO and flood flows from city of Chicago which runs full during rain events and must remain in service at all times. The project is a noteworthy feat for engineering and construction with the upcoming installation of world’s largest underground wheel gates for flow control within the tunnel. In this paper, we describe one of its kind elements of this major tunnel system along with key design and construction considerations, specifically for the live tunnel connection which is a rare occurrence in the tunneling industry. INTRODUCTION The McCook Main Tunnel system consists of a 10 m (33 ft) finished diameter and 490 m (1,600 ft) long hard rock tunnel constructed from a 27.5 m (90 ft) diameter and 92 m (300 ft) deep main gate and tunnel construction access shaft. The gate shaft houses six high head 4.4 m by 9 m (14.5 ft by 29.5 ft) wheel gates to be installed in the bifurcated and steel lined section of the tunnel. The tunnel also includes portal and energy dissipation structures as it daylights into the reservoir."

Jan 1, 2016

By T Ma, F T. Suorineni, Q He, J Oh

Directional hydraulic fracturing was invented by Polish experts and was first applied in coal mining to prevent hard roof rock bursts. Based on its successful application in coal mining, directional hydraulic fracturing has the potential to reorientate the hydraulic fracture trajectory. Recently, this technique has been introduced into cave mining for the purpose of lowering breakdown pressure. The hydraulic fracture is much easier to initiate with the assistance of an initial notch. No systematic theoretical or experimental studies have been carried out to investigate the influencing factors in the hydraulic fracture reorientation process. In this paper, the numerical modelling software Realistic Failure Process Analysis3D (RFPA3D) – Flow Version is used to study the influence of the in situ stress condition and rock mass heterogeneity on directional hydraulic fracturing in brittle heterogeneous rock masses. Firstly, the reliability of RFPA3D in simulating hydraulic fracturing is validated by comparing its results with experimental results and the simulation results from the extended finite element method. The hydraulic fracture trajectory is then observed in a three-dimensional stress environment. The results indicate that for the in situ stress condition, when the borehole lies in the ?2–?3 plane, only the difference between ?2 and ?3 has an important influence on hydraulic fracture reorientation. Furthermore, rock mass heterogeneity is a key factor that must be accounted for when fracture reorientation is required.CITATION:He, Q, Suorineni, F T, Ma, T and Oh, J, 2016. Modelling directional hydraulic fractures in heterogeneous rock masses, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 369–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R. P. van Hille, A. W. van Zyl

The BIOX® culture, aiding liberation of arsenopyrite/pyrite occluded gold, is inhibited by thiocyanate (SCN > 1 mg/L); precluding the recycling of tailings water up-stream of the bioleaching circuit. The activated sludge tailings effluent remediation (ASTERTM) process is a biological process that was developed to facilitate water recovery and treat waste water on-site (to achieve a SCN concentration < 1 mg/L) to be recycled or disposed of. The aim of this study was to investigate the effects of changing temperature and SCN loading on the SCN degradation ability of the mixed microbial population clue to seasonal temperature changes and fluctuations of SCN concentration in the waste water.

Jan 1, 2011

By Travis A. Davidsavor, Charles Dowding, David A. Provost, Yonggang Gou

This paper compares measured blast induced strains on operating, full scale, buried pipelines with three similar past studies. The recently performed study represents realistic and modern pipeline blasting techniques combined with modern data acquisition. The evaluation compares measured PPV and strain, as well as calculated stress, at equivalent scaled distances.

Feb 1, 2020

By E. H. Bentzen

The purpose of this paper is to explain the production of sand for glass manufacturing and the reasoning behind the sand specifications set by the glass industry. In order to discuss the production of glass sand, there is a need to understand what glass is and how it is made. Therefore this paper discusses glass, as well as sand beneficiation.

Jan 1, 1977

By M. Ito

Cobalt-rich ferromanganese crust and nodule ores from seamount areas contain volcanic and sedimentary rocks as substrate or nuclei and these ores require mineral processing to remove the substrate/nuclei rock before smelting. This paper reviews the results of jig separation and air table treatment for the coarse fraction and flotation and hybrid jigging for the fine fraction. Using these techniques substrate/nuclei rock was removed from the cobalt-rich ferromanganese oxide components. The mineralogical properties and metallurgical treatment methods including hydrometallurgical treatment of low grade ore is also reviewed.

Sep 1, 2012

By Emil H. Geus

A process has been developed to recover aluminum from dross which does not require the use of salt flux as commonly employed, This results in a salt-free residue which has potential industrial uses or alternatively can be safely land-filled. The dross is first heated by an air-fuel or oxy-fuel burner in a sealable rotary furnace. At a suitable temperature the burner is turned off and the temperature of the dross thereafter controlled by means of an atmosphere of oxidative and inert gases. When the free metal has agglomerated it is first discharged from the furnace, followed by the residues.

Jan 1, 1995

By John Rusnak

The Coal Mine Roof Rating (CMRR) is a practical rock mass classification system for use in design of mine openings. Data can be obtained for this purpose from exploration drill cores if simple geotechnical logging and rock mechanics testing is conducted. The CMRR is an excellent method to quantify rock characteristics for engineering purposes. It bridges the gap between geologic description and engineering design. The CMRR was utilized in the design of a 10,000 fl. long coal belt conveyor tunnel connecting an Eastern Associated Coal Corp. mine and preparation plant in Boone County, West Virginia. Data gathering and analysis techniques are discussed involving the calculation of the CMRR and its application in the design of the tunnel, which was driven through a thin coal bed zone. The preliminary findings have correlated well with actual roof and mining conditions encountered during driving the tunnel and it is concluded the CMRR is an effective method to utilize geologic data from exploration core holes for engineering analysis and design.

Jan 1, 1998

By R. W. Stahl

Burning coal-mine refuse banks were surveyed in 15 States. The following characteristics were tabulated for 495 hanks: County; name, population, and distance of nearest town; size and status of bank; status and stage of fire; and topography. Ways of controlling fires were reviewed, the compacting and sealing method proving most satisfactory. Means for preventing refuse-bank fires by proper construction of banks are described.

Jan 1, 1964

By Kenneth Seaver

It is rather gratifying that in the field of the manufacture of refractories, in which, as a whole, foreign practice has surpassed us, the United States stands pre-eminent in the making of silica brick. In some instances European manufacturers have refused point-blank to credit the possibility of making to such specifications as are Common with us, until the actual completed shapes were shipped for inspection. But both the manufacturer and consumer in foreign lands are now frankly learning from us, and benefiting by our advanced practice in this field, as is evidenced by the orders placed here and the efforts put forth abroad to come up to the standard of American-made material. In no metallurgical operation has the employment of silica brick spread with such leaps and bounds as in the building of plants for the carbonization of coal, particularly in the byproduct coke oven. Today, in practically all types of oven, the structure above the floor level (except the facings) is of silica, while in the recuperative and in some regenerative types, its use is extended to that portion of the oven below the floor as well. By reason of the fact that there are a number of classes of refractories of higher silica content than the usual so-called fire-clay brick, there is sometimes a misunderstanding as to the class of material referred to as "silica" brick. We here refer only to a brick having a silica content of 94 per cent. or more and made usually from quartzite rock with a small percentage of lime as a binder. The term "silica" brick is sometimes rather loosely applied to brick from highly siliceous clays, or to a quartzite refractory of mingled fire-clay and quartz rock; but such products are not considered in this discussion. : Materials The rock from which practically all high-grade silica brick are made is a true quartzite or metamorphosed sandstone, variously known as

Jan 1, 1916

By T. G. Melkus

A Setaram C-80 heat flux micro- calorimeter was used to study the surface and interfacial properties of fine coal particles in water containing flotation agents via heat of immersion measurements. Heat of immersion (?Himm) is usually a small exothermic quantity and can be used&apos; to characterize a solid in terms of its relative hydrophobicity or hydrophilicity. The effects of coal type, surface oxidation, mineral matter content, kerosene concentration, and pH on the wetting characteristics were investigated. Results obtained from the calorimetry experiments correlated well with results from independent flotation experiments.

Jan 1, 1987

By R. Lechuti-Tlhalerwa

"Geometallurgy aims to improve mining project value by predicting the impact that ore and waste characteristics will have on mining and metallurgical processes. This requires integration of rich spatial models of orebody characteristics with validated process response models. These models have, until recently, been constrained by the spatial coverage and representativity of relevant data and the ability to validate predictions made.The revolution in the diversity and volume of data and computational power that is now becoming available for integrated geoscientific modelling of orebodies, and stochastic simulation of mining and mineral processes is accelerating. By embracing emergent integrated data analysis and simulation techniques, geoscientists and engineers can lead a transformation in the way the mining value chain, from orebody to recovery, can be conceived, evaluated, and operated by using the geometallurgical paradigm.This paper describes a methodology that is applied to an existing diamond operation. Analysis of spatial and process data is used to build an integrated geometallurgical value chain model (IGVCM). This IGVCM is used to generate geometallurgical options and evaluate their potential outcomes. The model facilitates the use of flexible, highly configurable, and potentially automated intelligent approaches to evaluate mining and mineral process configuration, and results in more robust design outcomes. The approach described here, and its successful implementation has potential to deliver step-changes in value. IntroductionGeometallurgy aims to identify treatability risks – and opportunities – that arise from the interaction of orebody characteristics with mining and treatment. Improved understanding of the rock/process relationships allows project planners and production teams to predict performance, identify potential shortfalls, and thus enable the proactive creation and evaluation of strategies to mitigate these risks. These advanced insights also create opportunities for continually improving operational performance through dynamically adapting and improving the process response to the changing properties of the ore (Figure 1)."

Apr 1, 2019

By M Pyle, R Ch, T Vizcarra, ramohan, G Lane, G Ballantyne

Preconcentration, through gravity separation (Wallace et al, 2015), magnetic separation and particle size (Clout, 2013), has been used in many historical projects to convert low grade material into ore. More recently, pre-concentration technologies such as bulk sorting (Kurth, 2017), screening (Bearman, 2014) and coarse particle flotation (Vollert et al, 2019) have also demonstrated their ability to progressively reject waste through the value chain. These technologies can not only deliver stepchange improvements to the economics of mining operations, but can transform the environmental and social aspects by minimising water and energy consumption and significantly reduce the quantity of fine tailings produced. However, implementing progressive waste rejection requires technologies and approaches to be combined and applied in the right way to capture the value. From a technical perspective, progressive waste rejection introduces challenges related to the orebody, equipment performance, engineering and understanding the value chain from the resource through to final product. From a management perspective, the key issues are related to people and processes, in particular; motivating the business, challenging the paradigms, and introducing new ways of operating within the constraint of existing management structures to manage risks and minimise lost opportunity costs. This combination of technical and management issues means that progressive waste rejection is a complex undertaking for mining companies, yet the reward for the business and other stakeholders is potentially high and should not be ignored. This paper presents how progressive waste rejection can offer step-change improvements to the business case for high and low grade greenfield and brownfield projects based on case studies completed by Ausenco. The paper then outlines different implementation approaches from concept studies to execution to address the various technical and management challenges outlined above.

Nov 10, 2020

By-products are of greater importance in lead and zinc mining than in any of the other major base metals. While I think most mining people would accept that statement, you would probably get some widely varying estimates when attempting to quantify the value of by-products in lead and zinc mining. We are now able to do this with our lead-zinc mine cost model. This model was originally developed as a zinc mine cost model to help us forecast long-term zinc supply and price as part of a study we completed in late 1979 entitled "Zinc - The Next Decade". Before demonstrating the importance of by-product revenue to lead- zinc mines, let me first explain how the cost model was constructed. I will discuss the model as it was originally constructed - as a zinc mine cost model. It has subsequently been expanded to include lead only mines and now can Be run either as a zinc or a lead mine cost model.

Jan 1, 1980

By R. W. Stahl

Burning coal-mine refuse banks were surveyed in 15 States. The following characteristics were tabulated for 495 hanks: County; name, population, and distance of nearest town; size and status of bank; status and stage of fire; and topography. Ways of controlling fires were reviewed, the compacting and sealing method proving most satisfactory. Means for preventing refuse-bank fires by proper construction of banks are described.

Jan 1, 1964