Search Documents

By Jay F. Smith

The Alan Wood BOF Shop consists of two 140 ton furnaces with a rated yearly capacity of 1-1/4 million ingot tons, he hot metal for the BOF Shop is supplied by two 18 foot blast furnaces which produce an average of 2000 tons per day, To achieve the rated ingot ton capacity with this limited supply of hot metal, the preheating of scrap is necessary. This is accomplished in the furnace by using an oxygen-natural gas burner. Piping Arrangement The natural gas and oxygen are piped into the Shop through 8-inch lines to their respective valving stations. As can be seen from Figure 1, the flow of natural gas passes through a flow control valve which is common to both furnaces, after which it divides into two 6-inch lines forming two identical and independent gas control lines, one for each furnace.

Jan 1, 1972

By Silvia França, Hudson Couto, Renata Barbosa

"The flotation process, largely used for mineral concentration processes, which is based on air bubble adhesion to the dispersed solid phase, is also being used for wastewater treatment purposes. Dissolved air flotation (DAF) is based on the separation of the solid-liquid phases with the aid of small air bubbles (10-100 µm), with high values of interfacial contact area, improving the process efficiency. In the process, the air bubbles and particles or flocs form aggregates, which rise to the surface of the flotation cell to be collected. The advantage of producing small bubbles is directly related to the fact that smaller bubbles result in greater bubble-particle interaction. Wastewater produced in alumina refinery - from the red mud filtration step - has a red colored aspect due to the presence of very fine particles of red mud and also dissolved matter that still remain in the filtrate. This wastewater might be treated, aiming to reuse the water in the refinery or discharge it properly in the environment. The aim of this study was to evaluate the DAF process efficiency for the treatment of red mud wastewater in order to decrease suspended particles and dissolved solids contents, in addition to mitigate the high causticity of this wastewater. The process efficiency was evaluated by comparing turbidity removal and total solids concentration in the treated wastewater to the feed. The influence of important variables of the DAF process as type and concentration of coagulant and flocculant were evaluated. It was possible to obtain good turbidity removal efficiencies (up to 90%) using low concentrations of coagulant (50 mg/L) and flocculant (0.5 -1.0 mg/L). In addition, for most of the experiments, the specification for effluent diposal, according to the Brazilian environmental regulation 430 (Conama, 2011): pH range 5 to 9 and turbidity < 40 NTU, was attained. These results emphasize the possibility of using the DAF as an alternative technique to settling and filtration process, that are traditionally used, for treating wastewater from the alumina industry, allowing the reuse of water in the plant or adequate discharge with less environmental impact."

Jan 1, 2014

By J. H. E. Jeffes, C. Diaz

The heat balance and chemical equilibria involved in the production of blister copper from a chalcopyrite concentrate in a single operation are examined. It appears that two stages—one oxidising and one reducing—will be required. The analysis indicates that on thermal grounds the process is possible with a dry, high-grade chalcopyrite concentrate, if oxygen enrichment to about 30 per cent is used, but that copper losses in the slag will be serious and will require a secondary recovery operation. More extensive data on the activities of copper oxide in slags are required to elucidate this point more effectively

Dec 1, 1971

By William J. Wuest

The technical analysis of parameters that can influence roof and rib reinforcement is important to the operation of safe and profitable underground mines. One such parameter, studied in this U.S. Bureau of Mines investigation, is the effect of time on untensioned, resin-grouted bolt anchorage characteristics. A group of seventy-three 4-ft-long bolts with three different grout column lengths were I installed in a stable coal mine roof. The bolts were then subjected to standardized pull tests at various intervals throughout a 37-month period. For each test, load-deformation data were reduced to determine axial stiffness and yield point. The magnitudes of these two anchorage characteristics at the time of installation were compared with results from subsequent pull tests to determine if anchorage capacity deteriorated. Bolts with 18-in grout columns were studied over 9 months, and no measurable loss occurred. Bolts with 48-and 24-in grout columns were studied over 37 months and also exhibited no measurable loss.

Jan 1, 2010

By F. A. Skirvin

Purification techniques were investigated for removing low-level metallic impurities from tungsten hexachloride. These techniques included distillation) fused-salt scrubbing) zone refining) and adsorption. Fractional distillation of tungsten hexachloride was found to be an effective purification method. The impurity levels of molybdenum) iron) nickel) copper) magnesium) and manganese were reduced to provide a tungsten halide sample which contained a total of less than 10 ppm detectable metallic impurities. Purification by fused-salt scrubbing of tungsten hexachloride in a lithium chloride-potassium chloride eutectic produced a hexachloride product which was of approximately the same quality as that obtained by distillation. Zone refining and adsorption did not appear to be as effective as distillation or fused-salt scrubbing.

Jan 1, 1967

By M. B. McClenaghan

"Abstract- The Ontario Geological Survey completed a regional till sampling project between 1984 and 1988 in the Black River Matheson (BRiM) area of northeastern Ontario. The project was designed to aid mineral exploration in the area by documenting the Quatemary stratigraphy and by providing a database of till geochemistry. This paper summarizes the results from the sonic overburden drilling component of the BRiM project carried out in areas of thick drift (> 5 m). Results from till sampling in areas of thinner drift (<5 m) have been presented in a separate paper. Approximately 1100 till samples were collected from 225 sonic drill holes. For each sample, the non-magnetic heavy mineral (> 3.3 S.G.) and fine (-250 mesh) till fractions were analyzed geochemically and visible gold grains were recovered by panning.Gold and other multielement geochemical data were plotted using proportional symbols to high­ light anomalous areas and to demonstrate how to evaluate and interpret a very large geochemical dataset. Thresholds for identifying anomalous concentrations of Au in till samples, defined using the 95th percentile, are 1500 ppb and 12 ppb for the heavy mineral and fine fractions, respectively. The heavy mineral fraction of older tills and to a lesser extent, Matheson Till, display a number of significant gold anomalies in the study area, which in a few cases, are associated with base metal anomalies. The vertical position of gold anomalies in Matheson and older tills varies from directly on bedrock to several meters above the bedrock surface and can provide information of relative ice transport distances."

Jan 1, 1994

The following letter has been received from Professor P. A. Young, Head of the Department of Mining and Mineral Engineering at The University of Leeds, England. Extractive and process metallurgy The first annual TMS-AIME Extractive and Process Metallurgy Fall Meeting:1983 International Sulfide Smelting Symposium, will be held from 6th to 9th November, 1983, in San Francisco.

Jan 1, 1982

By Malti Goel

"Technology advancements in fossil fuel based energy generation and consumption are currently being aimed at minimization of CO2 emissions. To attain energy security, India must accelerate the pace of economic development, while achieving reduction in CO2 emissions per unit of energy consumed. It would need access to advanced coal utilization technologies to be demonstrated on indigenous coal characteristics. Of specific importance would be: improvement in coal quality, increasing energy efficiency and suitability of other CO2 sequestration technologies for reducing CO2 footprints. There is need to address related risks and financial burden through adoption of policies and regulations including the issue of open access in energy research. In this paper, seven important areas of strategic plan that need to be pursued for managing CO2 emissions in steel energy sector in India are discussed.IntroductionWorld is facing a crisis of climate change, which follows in the footsteps of global energy and environment crises. Accumulation of carbon dioxide from the generation and utilization of energy is leading to greenhouse warming and climate change. The global warming is causing the boundary between four seasons to be fuzzy and resulting in more spiky weather. Significance of its impact on environment is also determining the technology development needs in various sectors of economy for taking remedial measures.To respond to climate change concerns, the steel industry is undergoing a transition. It is at the threshold of a rapid change in technology as it targets innovation to achieve 50% reduction of CO2 emissions per ton of steel produced. Fossil fuel use is the main contributor of increasing concentration of carbon dioxide in the atmosphere. The control of air pollution and CO2 capture are thus relevant for a coal based industry, whether thermal power plant or a demand side energy intensive industry. World steel production has shown phenomenal increase in first eight years of 21st century increasing from 780 Mt in 2000 to 1343 Mt in 2008 [1]. It was merely 28 Mt in 1900. The global CO2 emissions from steel industry are also increasing and became 2550 Mt (3-4% of total GHG). Indian industry contribution was 161 Mt (15% of direct emissions from industry). It is likely to grow further to keep pace with the accelerated economic growth of 8-9% per annum."

Jan 1, 2010

By E. W. Davis

DURING late years, the proportion of beileficiated iron ore shipped from the Lake Superior District has increased very rapidly. By benefication is meant washing, screening, drying, sintering or any process by which the grade or structure of the crude ore is improved before shipment. In 1915, only 3,000,- 000 tons, or 9 per cent, of t6e total Minnesota shipment was beneficiated ore, compared with 13,500,000 tons, or 35 per cent, of the total Minnesota shipment in 1925. This increase is, of course, due to the fact that iron and steel can be made more cheaply after beneficiating these ores than they could have been had these ores not been so treated. Fundamentally, however, several causes contribute to the necessity for beneficiating iron ores, such as depletion of the reserves of high-grade ores, the iron ore leasing systems and taxation methods and, at the smelting plants, a better understanding of blast-furnace operations, increased operating costs and increased sulfur content of blast-furnace coke. As economic conditions change, it is by no means certain that the proportion of beneficiated ore shipped each year is going to continue to increase. Undoubtedly some of the beneficiation operations are not economically sound at the present time and what the future has in store for the iron ore industry is problematical. Generally speaking, the cost of fuel for blast-furnace operations will increase as time goes on and in order to continue to produce cheap iron and steel, some of the other costs must be lowered. Freight and labor rates probably can- not be reduced. The cost of producing iron ore cannot be reduced much below the present price. It therefore appears that the best opportunity for maintaining iron and steel prices at their present level in spite of in- creased costs of labor and raw materials is to use. less or cheaper raw materials. This, of course, contemplates an improvement in metallurgical processes all along the line and, as a matter of fact, we can confidently expect these improvements because scientific investigations will undoubtedly be even more productive in the future than they have been in the past.

Jan 1, 1926

By Joseph Hirschi, Behrooz Abbasi, Harrold Gurley, Yoginder P. Chugh

"The research goal was to assess if analytical tool/s can be developed to quantify displacements around a geological fault as longwall face moves toward it and past it. A company was faced with crossing a 2-3 m (6-10 ft.) normal up-thrown fault in the development entries and the face while mining a 375 m (1,200 ft.) wide longwall face. A field monitoring and numerical modeling study was performed to develop data. Field measurements consisted of roof-to-floor convergence and rectangular rosettes in the immediate roof. Numerical modeling consisted of constructing a 3-D structural model using the FLAC3D software with the fault plane incorporated as ubiquitous joint. Based on analyses and field observations data, the coal company was informed of impending movements along the fault plane and likely impacts on the development entries. Additional stiff supports were installed in head gate entries around the stage loader and equipment about 60 m (200 ft.) outby of the longwall face (solid). As the longwall face approached the fault, predicted displacements were documented and manifested by severe loading on the installed supports.BACKGROUND AND STUDY OVERVIEWThis paper summarizes results of a cooperative study aimed at improving longwall mining operations in Illinois. More specifically, the study focused on: 1) In-mine measurements in development entries while mining ahead of and behind a faulted zone, 2) Making observations on stability of pillars and entries while mining through the fault, and 3) Developing simplified analytical structural models using FLAC3D to assess if predictive techniques can be developed to plan mining operations through fault zone. Available data on geometry of the fault with estimates of the cohesion and frictional parameters were used for modeling."

Jan 1, 2015

By P. S. Newall

As part of a much larger research project, factor analysis was employed to help interpret and compare the geochemical signatures produced by two different sample media; a traditional -80# soil fraction, and a coarse float. Both sample types were collected by hand auger from the extension zone of the Redmoor sheeted-vein complex and analyzed -for 19 major and trace elements. The rationale behind the study infers that the geochemical anomalies produced by wallrock alteration around such targets can be better detected in the lithogeochemical rather than the soil environment, sometimes at considerable distance from their source.

Jan 1, 1991

By Rafael Colás

Computer visualization can be employed in industry as an aid to the understanding of the complex interactions between variables encountered in production. The examples of ingot casting of rimming steel and that of hot rolling of low carbon steel strip are presented. Both processes are mathematically modeled, and their results are presented in a graphical way. Such models have been proven to be an asset in quality improvements and increase of productivity as the personnel involved get a better understanding of their job.

Jan 1, 1993

By Paul D. Tomlingson

World class performance is the ultimate objective of many maintenance organizations. It marks the organization as a leader in its industry and sets it apart as the ultimate achiever. But what is a “world class” standard and how can it be achieved? Is there a yardstick by which an industrial organization can measure the relative performance of its maintenance activity and compare it with performance levels that universally identify “world class” status? Are there financial formulas, achievements, evaluation techniques or indices that provide this yardstick?

Jan 1, 2006

By Paul D. Tomlingson

There are huge benefits for mining operations that have a well-defined maintenance program that is understood and followed across the total operation. But for operations lacking a quality maintenance program, there is equal assurance that nearly every major maintenance problem can be traced to this omission. Few problems will be permanently corrected until such a program is implemented. Definition The maintenance program re-quires the interaction of all mine departments. Initially, the production department will request work and the maintenance department will identify work, principally through preventive maintenance inspection and testing efforts. Maintenance will then classify the new work to determine the best way to respond. Maintenance will plan selected major jobs to enable its crews to carry them out more effectively. Maintenance will schedule the planned work with operations. Supervisors will assign all types of work to their crews then, control the work through effective supervision. As work is completed, maintenance will measure the work using an accurate information system. Next, it will assess overall accomplishments against goals such as performance standards or budgets. In addition, the pro-gram would prescribe a means to evaluate every aspect of the operation as it affects maintenance so that necessary improvements or changes can be identified, prioritized and acted on. Such evaluations should be part of a mine-wide continuous improvement effort. A well-defined maintenance program is one of the best investments a mining operation can make to assure its profitability. Educating the total operation on the pro-gram assures long-term dividends from the investment.

Jan 1, 2008

By H. Ogasawara

To study the preparation process of an earthquake, we should get closer to the hypocentre. In co-operation with ISS International, we had an experimental field (~200 m x~200 m) without dykes and faults in a South African deep gold mine. We have monitored more than 20,000 seismic events (M<2) with borehole tri-axial accelerometers. We used a data acquisition system with 15 kHz sampling and 120-dB dynamic range. In a remnant area at a distance of 100?200 m, an earthquake sequence associated with an M~2 event occurred. Significant changes in seismic parameters such as stress drop, b-value, energy index were observed associated with the sequence. We installed Ishii?s borehole strain meters and could monitor as large a strain change as 10-4associated with mining. However, sampling was only 4 times per hour and 12 bit A/D. A distance from the M2 sequence was ~100 m, being not close enough. Therefore, we found another field with several crosscut tunnels excavated across a fault where an M=2-3 event is expected. We installed the strain meter within several metres of the fault to monitor both shear and normal strains on the fault. The strains are continuously digitized with a 24-bit 25-Hz A/D conversion. The Earth Tide (10-8)is clearly detected. Seismicity induced by longwall mining can be compared to earthquake swarm induced by fluid intrusion to vertical dykes. We also found a decrease in energy index in the source area of M>5events a few days before the major events. Keywords: seismic monitoring, strain monitoring, seismic parameters, preparation process of an earthquake, South African gold mine.

Jan 1, 2002

Discussion of the paper of HOWARD N. EAVENSON, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 413 to 430. WILLIAM H. GRADY, Bluefield, W. Va.-Mr. Eavenson gave a comparison between accidents in the State of West Virginia and in the Pocahontas field. The figures quoted are, I presume, taken from the reports of the State Mine Inspector. There are no statistics available, in readily accessible form, giving a comparison between the Pocahontas field and the mines of the United States Coal & Coke Co. which are a part of the field. It occurs to me that the paper would be more complete with these data and I will say that the mines of the Pocahontas field produced during the year 1913 about 15,000,000 tons, about 3,000,000 tons of which was produced by the United States Coal &Coke Co. This gives an indication of the extent of its operations. The Pocahontas field lies largely in the counties of McDowell, Mercer, and Wyoming in West Virginia, and Tazewell in Virginia.: Without consulting maps, I should say that all of the acreage under operation at present by this company lies wholly in McDowell County and that the average conditions off roof top and bottom in its mines are the average of the county, but that the worst conditions in some of these mines are the worst to be found in the county. The average conditions in Tazewell County are about the same as in McDowell County, except that the average thickness of the seam is much greater. The average conditions of top and roof and bottom are better in Mercer and Wyoming counties than in the mines of the United States Coal &. Coke Co.; the worst conditions in these counties are not so bad as in McDowell and Tazewell counties and the best are better than those encountered in McDowell and Tazewell counties; also the thickness of seam is less in Mercer and Wyoming counties. THOMAS W. DAWSON, Scottdale, Pa. (communication to the Secretary*).-The H. C. Frick Coke Co., the mines of which are in Fayette and Westmoreland counties, Pennsylvania, in the Connellsville coke region, has been pursuing a safety campaign for a number of years and a short resume .of its practices will be of interest in connection with Mr. Eavenson&apos;s paper.

Jan 5, 1915

By James D. Noll, Jon A. Hummer, Shawn E. Vanderslice, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health designed and conducted a study in an underground metal mine to assess the effects of selected diesel emissions control technologies on the concentrations of diesel particulate matter and gases in underground mine air. The control technologies studied included diesel particulate filter (DPF) systems, filtration system with disposable filter elements, diesel oxidation catalytic converter, and biodiesel blends. Each technology was tested on a mining vehicle operated in an isolated area of an underground mine supplied with fresh air. These isolated zone tests allowed for the operation of vehicles under conditions and over duty cycles that closely mimic actual duty cycles of production equipment. The DPF systems reduced the elemental carbon (EC) concentrations in mine air between 88% and 99%. The same systems reduced total particulate matter (TPM) concentrations in mine air by approximately 75%. The biodiesel blends B20 and B50 caused a reduction in the EC concentrations of 26% and 48%, respectively. Those blends also reduced TPM concentrations by 9% and 24%, respectively. The use of #1 diesel fuel reduced EC concentration by 13% compared to #2 diesel fuel. An increase in nitrogen dioxide concentration of up to two times was seen when platinum-catalyzed DPF systems were tested.

Jan 5, 2006

By H. H. Murray

Industrial usage of clays for current and new applications will continue to grow into the next century. The rate of growth will be highest in the less developed areas of the world. Transportation costs are a significant part of the delivered price, so the location of reserves and processing facilities for kaolin, bentonite, and palygorskite (attapulgite) are reviewed relative to serving these emerging markets. New value added applications will increase in the more developed areas which will require high quality raw materials, more sophisticated processing, and rigorous quality control.

Jan 1, 1998

By Mark Coleman

Pnuematic Conveying and Process Injection Technologies have been implimented in the metals markets for the last 40 years and have consideribly improved the productivity and the performance of many processes. There have been many steps forward in handling technology and this paper seeks to consider those now offered by Clyde Materials Handling who as an established customer-driven solutions provider, which has turned its attention to supporting the Metals Market. Clyde seek to utilises its knowledge, expertise and technologies to transform the production processes of its customers, who operate in the ferrous and non-ferrous metals industries. With over 30 years experience in the process improvement industry, Clyde Materials Handling has helped their global customer base transform the way in which they operate their processes, which has enabled them to generate sustainable economic benefit and maintain their positions as leaders in their respective markets. Operators within the metals market have developed and deployed pneumatic conveying and pneumatic injection technologies. These environmentally supportive and sustain-able solutions have been used to transport raw materials within operating facilities, from storage to silo, as well as injecting these materials directly into the heart of production processes. Operators, such as Codelco in Chile, Corus Steel in the UK, and many others across the World have seen pneumatic injection solutions transform their process and costs. To inject a consistent, pulseless and accurate flow of material to a copper concentrate bath smelter, or injecting granular or pulverized coal as a coke substitute in to a blast furnace via the Tuyeres helps to increase the operational capacity, availability and productivity and reduce the cost of the operation. This paper will discuss and highlight the ways in which pneumatic conveying and injection technologies, created by Clyde Materials Handling, and applied in partnership with the customer, have helped to improve the operational performance of the production processes of operators across the non-ferrous metals markets with specific reference to applications in the Lead and Zinc Industries. With examples from Zinc Fuming in Australia, Zinc Calcine and Powder Handling in Korea, Precision coal injection to QSL and TSL Furnaces, and metered distribution of Zinc Calcine to Reactors.

Jan 1, 2008

"The reduction works of the Boston & Montana Reduction department, near the north end of this dam is one of the reduction plants belonging to the Anaconda Copper Mining Company, the other being at Anaconda. These works employ about 1,100 men and have a capacity of about 3,800 tons of crude ore per day. This plant is now being remodeled to embody results of experiments and investigations which have been made with a view to more economic.al treatment of ores. A brief description of the plant as it will be after the remodelling is as follows:Concentrator Department: Consists of six units or sections, each section treating from 550 to 600 tons of crude ore per day. This department is not being. remodelled at the present time. A concentrating process, however, has been developed and partially installed in the old mill, and an experimental section embodying this concentration process has also been installed at the concentrator at Anaconda."

Jan 1, 1913