Search Documents

By Y. Chengxian

Many factors about the HIC (hydrogen-induced cracking) resistance of pipelines are discussed in this paper. The main factors that influence the ability of HIC are environmental and material factors. The chemical compositions, non-metal inclusions and microstructure are discussed in detail, while a group of tests on HIC resistance are done according to varying C, S, Mn and P contents in pipeline steels, different experiment time and different strength to the coupon. It is concluded that decreasing the amount of C and S can obtain good HIC resistance; the test time has an effect on the different microstructure of X70; microstructure is the most sensitive factor for the initiation processes of HIC.

Jan 1, 2005

By John V. Beall

The forecast of continued growing demand for phosphate, chiefly for fertilizer, has caused a world-wide rush for deposits by a variety of companies many of which have never before mined phosphate rock. The newcomers are diversifying into this growth industry on the strength of certain capabilities. Among these are the availability of investment capital, mining or processing know-how and marketing experience. Product tie-ins have motivated some into the search. Companies with excess sulfuric acid or potential for making it are in this category. This acid is the most commonly used for dissolving phosphate rock to make phosphoric acid. Base metal smelting companies are prime candidates in this field with by-product acid from roasting processes. Producers of "sweet" natural gas, such as those in Louisiana and Texas, have a potential for recovering low cost hydrogen from excess gas production for the manufacture of ammonia, the main source of nitrogen for fertilizer. "Sour" gas producers, such as those in the Canadian fields, are making sulfuric acid that is combined with western U.S. phosphate to make fertilizer materials. The presence of one or two steel companies in the look-see for phosphate deposits is based on by-product ammonia from coke-oven gas.

Jan 10, 1966

By J. C. Stankus

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a slope entry, the problem is more difficult because a slope will transverse through many different types of strata. Over the past three years, Keystone Mining Services, LLC, an affiliate company of Jennmar Corporation, has developed a new methodology designated the ?Stress, Geologic, and Support Design System (SGSsm)?. This patent pending method analyzes the stress, geology, and support design for a mine slope. It has been successfully applied in various new slopes across the United States. This paper will detail the main concepts of the methodology including: (1) Analysis of stress and geology and identification of strong, fair and weak zones along the slope; (2) Primary and supplemental support design; (3) Long term support design in the form of steel square sets or arches, and (4) Validation of the support design utilizing advanced finite element computer modeling.

Jan 1, 2011

By Dany Racine, Daniel Marceau, Denis Laroche, Dmitry Lukovnikov

Carbon base materials play a critical role in the performance of Hall-Héroult cell. The determination of their thermo-physical properties is of primary importance for modeling and designing complete cell systems. However, overcoming the associated experimental hurdles is complex and often underestimated. Of them are the Poisson’s ratio measurements and the continuous oxidation/burning of the materials at temperatures above 200°C. The novel procedure developed in this research is based on the Gleeble® 3800 system. Its vacuum chamber allows test with a chosen atmosphere at temperature of more than 1000°C. Young’s modulus, Poisson’s ratio and the coefficient of thermal expansion values can all be adequately measured using a single test. Cylindrical carbon samples (: 50mm, L: 100mm) were tested in the modified system at temperatures ranging from room to 950°C without any trace of oxidation. The resulting values were also in good agreement with literature data for a specific graphite material.

Jan 1, 2015

By Bluhm S. J, Feio L, Ramsden R

A new mining area at the Vaal Reefs gold mine is to have a shaft. system which will extend to a depth of 4 200 m and will require 130 MW of cooling. A novel feature of the proposed cooling system is a large underground air cooling installation in which an ice slurry is sprayed into the ventilation air. The design of the ice slurry bulk air cooler, in the form of counter.flow cooling towers, is discussed. Comparative thermal tests with cold water and ice slurries (with ice mass fractions up to 22 per cent), were carried out in a 5 m high test tower. The presence of the ice in the water spray increases the resistance to heat flow and reduces the overall thermal characteristics of the air cooler by 8 per cent. Notwithstanding this, the use of ice slurries is indeed beneficial in terms of overall costs. It is concluded that a 25 MW air cooler should use 410 kg/s of ice slurry with a 10 per cent ice mass fraction to cool 550 kg/s of air which is 75 per cent of the total air flow rate.

Jan 1, 1988

By Shadia J. Ikhmayies

CdSxTe1-x and CdS1-yTey solid solutions are usually formed in the interfacial region in the CdS/CdT thin film solar cells during the deposition of the CdTe layer and/or the processing steps of the device. It is well known that CdCl2 heat treatment encourages the formation of the CdSxTe1-x alloy which improves the solar cell performance. In this work, indium doped CdS1- yTey thin films are produced by first producing CdS:In thin films by the spray pyrolysis (SP) technique on glass substrates, then annealing the films in nitrogen atmosphere in the presence of elemental tellurium. The films are characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), and transmittance measurements. The transmittance is used to deduce the optical parameters such as; the extinction coefficient, refractive index, besides to the real and imaginary parts of the dielectric constant. The dispersion parameters such as Eo (single-oscillator energy) and Ed (dispersive energy) of the deposited films are also estimated and discussed.

Jan 1, 2015

By Joseph M. Kuchta

The limits of flammability and minimum autoignition temperature of a fuel are important elements in assessing fire and explosion hazards that may exist when using or handling the fuel. The limits of flammability define the range of compositions of the fuel gas or vapor mixed with an oxidant through which a flame, initiated by an outside energy source such as an electrical spark, can propagate. The minimum autoignition temperature (M.A.I.T.) is the lowest temperature at which the fuel vapors ignite spontaneously in a specified medium; in this case the ignition energy is supplied by the heat content of tae environment. This temperature is also referred to as S.I.T. value by some authors. Because the autoignition of a fuel also depends on the time interval during which the fuel is subjected to heat, ignition delays are significant. Ignition delay is defined here as the total time elapsed between the introduction of the liquid fuel into the oxidizing atmosphere and the appearance of a flame. This time interval includes both the physical and chemical processes leading to ignition. The ignition delay is usually maximum at the M.A.I.T, and decreases as the temperature of the system is increased. The flash point and the fire point are also useful in assessing the fire and explosion hazards of a fuel. The flash point is the lowest temperature at which saturated, flammable fuel vapor-air mixtures are formed at atmospheric pressure and, therefore, it is essentially the lower limit of flammability

Jan 1, 1962

By W. R. McClelland

GOLD-BEARING ores, representing many types, are found widely distributed through the Province of British Columbia. They range from those which by their nature may be considered as complex, to those whose mineral characteristics are simple. Those in which the gold is associated with metallic sulphides provide particular milling and metallurgical problems, the solution of which involves not only detailed laboratory investigation but also a careful consideration of economic factors. The location of an ore-body may have a deciding influence on the adoption of a method for the metallurgical treatment. Whether the ore should be treated with the object of recovering the gold as bullion or as a shipping concentrate is often dependent on such topographical considerations as the position of the mine at or near tidewater or within a reasonable overland distance of a smelter. British Columbia is fortunate in having the Trail smelter situated in the southern part of the Province, and the smelter at Tacoma, Washington, is accessible for coastwise traffic. Both of these provide a ready market for most types of gold-bearing concentrate. In order that the results obtained by laboratory tests may give a fair indication of what should follow in mill operation, it is essential that the test sample should represent as closely as possible in mineralogical character and in grade the ore that eventually will constitute the feed to the mill. In the early stages of mine development this consideration is sometimes overlooked and samples of a much higher grade than would be representative of run-of-mine ore are submitted. Flotation tests on such a sample of ore high in sulphides may show a low ratio of concentration, bu.t if the actual run-of-mine ore is lower in sulphides the mill operation will reveal a much higher ratio. The recommendations for treatment based on the results of laboratory tests may have been against concentration, when in actual operation this would be the most suitable method of treatment. Recommendations based on laboratory tests are necessarily from the results of work carried out on the sample submitted, modified only by such other economic or topographical information as may be known to the investigator. This paper deals with a few of the gold ores found in the six mining districts of British Columbia and is based on investigations made in the Ore Dressing and Metallurgical Laboratories of the Mines Branch, Department of Mines, Ottawa.

Jan 1, 1937

By John R. Eckel

A Iaboratory drilling rig has been devised and placed in operation which permits the application of hydrostatic, terrastatic, and formation pore pressures to a rock sample for drilling under controlled conditions. Calibrated rests of this equipment in-dicate qualitative agreerment with field results on the effect of weight on bit, rotary speed, and rate of circ~~lation on drilling rate. Tests under pressure, using water and air as the drilling fluids, indicate that when drilling saturated limestone samples, a pressure differential between hydrostatic and formation pressure is the only pressure which affects drilling rate. A differential in either direction causes a reduction in rate, but the same diflerential from the wellbore into the formation causes the greater reduction. Also, in lime.stone, air favorably affected drilling rote only when compared to water at high hydrostatic pressurre, all other conditions remaining constant. Large increases in drilling rate with air could be obtained in the laboratory only while drilling a shale, which offered a limited permeability to nitrogen and which could be drilled with a differential from the formation into the wellbore. In general, the magnitude of the changes due to the pressure effect were small compared to changes in drilling rate obtainable by changing either bit weight or rotary speed. INTRODUCTION In the course of Humble's drilling research program, the desirability of investigating several factors which lend themselves to laboratory rather than field study became obvious. Principal reasons for this are the expense involved in field studies and the difficulty of exercising the required degree of control. Of primary importance are investigations of the effect of fluid pressure on rock rate, the effect of pressure on rock drillability, and a study of the fundamental mechanics of rock failure and chip generation. Several years ago some work in the laboratory on the effect of mud properties on drilling rate was re- ported to the API', but the completion of this work and the investigation of the other variables affecting drilling rate required equipment somewhat more elaborate than that used on these earlier tests. This equipment has been assembled to form Humble's Drilling Engineering laboratory. To date only the effect of pressure on rock drillability while using water and air has been investigated, and this work is not yet complete. Facilities are available to investigate the effect of fluid properties on rate of penetration, and information is being assembled on a current basis on the mechanics of drilling. The sequence of presentation in this progress report is somewhat different from that in which the data were obtained since the order of ex-

By Aaron L. Sacks, David R. Good, Srinivas Yennamanda, Joseph K. Carey

Construction of Parcels 6 and 7, the second phase of The Wharf, began in 2019 and geotechnical construction was completed by December 2020. The overall project consisted of horizontal site, parks, and office buildings. The Wharf’s Phase 2 development includes approximately 1.2 million ft2 (110,000 m2) of above-grade construction including five multi-story, mixed-use buildings constructed over up to three levels of underground parking. The site is located between the WMATA Green Line Tunnels to the north and the Washington Channel to the south; it is bisected by a 108-in. (2740-mm) diameter DC Water outfall pipe. This arrangement, along with very difficult ground conditions, created challenges in the geotechnical design and construction. The support of excavation for this complex project required several different methodologies, including sheet piles, soldier piles, displacement piles, tiebacks, deep foundation anchors, jet grouting, and internal bracing with multi-tier rakers. Ground improvement was also required for support of spread footings in soft soils over the garage footprint. Underpinning of the active 108-in. (2740-mm) diameter DC Water outfall pipe running on a north/south alignment through the center of the site between the two garage structures was also performed. Since portions of the support of excavation are below the groundwater table, an extensive pre-excavation dewatering program was necessary and was separate from the foundation package. On the north side of the project, support of excavation (SOE) was required on a curved alignment, offset approximately 10 ft (3 m) from the outbound Green Line tunnel. Due to the proximity of the tunnel, a stiff, near-zero displacement wall was required. A portion of the buildings extend over the tunnels, imparting load to the tunnels to approximately restore original overburden loads excavated for the basement space. The building foundation is a 3 to 4-ft (0.9 to 1.2-m) thick mat slab anchored into the Potomac clay formation. Continuous movement monitoring of the tunnels was performed by an automated system. This paper describes the design and construction of the SOE and foundations for this high-profile project, which required collaboration between the Owner, Engineer, Construction Manager, and Specialty Geotechnical Contractor to solve many challenges.

Oct 1, 2022

By J. C. Gerdeen

A new analytical model for the shear stiffness at a joint of the fully-grouted resin roofbolt is developed using the Theory of Elasticity and an analogy to a beam on an elastic foundation, Gerdeen [2]. The model developed in this study treats the elastic foundation modulus of the resin as being composed of both an elastic rock and an elastic resin. All previous attempts have neglected the elasticity of the rock and treated only the resin. A three dimensional finite element model of the bolt-resin-rock system is developed also and comparisons are made between the predictions made by it and the analytical solution. It is found that the agreement between the two representations ranges between 1.2% and 10.5%, with the greater differences being observed for systems of very large or very small bolt diameters and resin annulus thicknesses. Since such configurations are not the rule in practice parameter studies are performed using the analytical solution with the finite element solution being used as a check. For a 0.75 in. bolt, a resin annulus thickness of 0.1375 in., a resin with E = 7 x 105 psi and -1) = 0.210, and a rock of modulus E = 6.8 x 106 psi and V = 0.159 the shear stiffness is found to be 1.220 x 106 lb,/in, from the analytical solution and 1.245 x 106 lb,/in, from the finite element model. Applying the finite element model to the problem of the axial stiffness of the fully-grouted resin roofbolt a value of 6.002 x 106 lb./in. is obtained which proves to be at least 50% higher than any of the now existing analytical predictions.

Jan 1, 1976

By John F. Parmeter

On August 29, 1989, the Department of Labor, Mine Safety and Health Administration (MSHA), published a Federal Register concerning a new proposed rule on air quality, chemical substances and respiratory protection standards. As of this writing, their proposed rule has not become a standard. However, with little revision it could be expected to become a standard, and we in the mining industry will be expected to adhere to and enforce it.

Jan 1, 1991

By Shoukun Wei, Cong Wang, Lin Cheng, Zhiyu Qiao, Jingkui Liang, Weidong Zhuang

"The subsolidus phase relations in the Sm2O3-CeO2-CuO ternary system sintered at 1000°C in air have been investigated by X-ray powder diffraction. The system can be divided into two ternary phase regions and three binary phase regions. Solid solution Sm2-xCexCuO4-y is the only ternary phase in the system. The maximum solid solubility was confirmed to be x = 0.2. The crystal structure, oxygen content and superconductivity of the solid solution Sm2-xCexCuO4-y have been investigated.I. INTRODUCTIONAfter the first discovery of the superconducting ceramic system La-Ba -Cu-O[l] with Tc = 30 to 40K, other families of cuprate-based ceramics have been synthesized with higher critical temperature. These oxides include the R-Ba-Cu-O (R: rare earth) systems (Tc=90K or so)[2,3], the Pb-Sr-(R,Ca)-Cu-O systems (T c = 50 to 100K), the Bi-Sr-Ca-Cu-O systems (Tc=80 to 105K)[4], the T1-Ba-Ca-Cu-O systems (Tc=85 to 125K)[5], the Hg-Ba-Ca-Cu-O systems (Tc=90 to 150K)[6,7], and some others. The improvement of Tc is very rapid. The measurement of the Hall and Seebeck coefficients shows that they all are p-type superconductors. In 1989, Tokura et al.[8] discovered the superconductors R2_XCexCU04_y(R = Nd, Pr, Sm) with Tc=20 to 24K (onset) and found that the charge carrier is electron in contrast to their hole doped counterparts. This discovery increases the fundamental understanding of the cuprate-based superconductors by comparing their characteristics and mechanisms to those of the p-type superconductors.One of the outstanding features of these n-type superconductors is the difficulty in obtaining samples in good charactors, such as the difficulty in obtaining zero resistivity state in single crystal or bulk samples; the semi-conductivity of bulk samples in ordinary state (opposite to the superconducting state) and a reducing reaction involved before the superconductivity has been found[9]. Therefore, it is necessary to optimize the sample preparation of the n-type superconductors. All the n-type superconductors have been found· considerable solid solubility. The compositional variations play a governing role in the carrier doping of the superconducting phases. Also, it is vital to the ceramic processing of superconductors to identify the compatible phases in the phase diagram. Finally, there is always the possibility of finding additional compounds, both superconducting and non-superconducting, in an unexplored system."

Jan 1, 1996

By Julián M. Ortiz

Uncertainty quantification of a spatially distributed variable at any scale can be handled through geostatistical simulation. Large computation time, storage, and post-processing of the realizations are required to obtain a final assessment of block uncertainty. Multi-Gaussian kriging is a flexible alternative to simulation. The idea is to compute the conditional distribution of uncertainty after normal score transformation of the original samples. Under the multi-Gaussian assumption, all marginal and conditional distributions are Gaussian, hence fully defined by their mean and variance. The parameters of the conditional distributions are obtained by simple kriging and can be back-transformed to the original units of the variable of interest. An estimate and any summary of uncertainty can be easily retrieved. The main disadvantage of performing multi-Gaussian kriging is that change of support is not straightforward, that is, calculating uncertainty of block grades. We propose a methodology to overcome this limitation by considering a matrix simulation to generate multiple probability fields. Each probability field is used to draw spatially correlated point values from the point-support conditional distributions, and multiple realizations of the average can be obtained. This permits the calculation of the average over the block and its uncertainty. These blocks may correspond to selective mining units or to volumes from longer production periods relevant for engineering decisions. They can even be disjoint blocks, such as when several faces are mined at the same time. POSTMG, a Fortran program to perform these calculations, is described and a case study is provided.

May 1, 2004

By H Ş. Duzgun

It is expected that the future of mines will heavily adopt autonomy. However, problems with leveraging workforce transition, meeting Sustainable Development Goals, SDG’s (poverty, reduced inequalities), managing uncertainties (geologic, operational, economic), cybersecurity (connectivity, cyber-physical infrastructure) and innovation (transformative processes, real-time decision-making etc) are required to be solved for the intended autonomy. These problems also impact the safety of the future mine environment. The AI technologies provide a broad range of opportunities for enhancing mine safety. However, development of an accurate AI model for mine safety requires a large number of data, which may not be readily available to overcome the associated uncertainties in the mine environment.

May 5, 2022

By R. J. Mechin

IN the early part of 1934, the St. Joseph Lead Co. purchased from the Kadco Corporation three dust-removal units, two suitable for raise work, and the other for drifting operations. The equipment was installed at the Balmat mine, in St. Lawrence County, New York. The Kadco dust-control system can be briefly described as one in which hoods, through which the drill steel is drawn, control the dust at the drill hole, the dust is conveyed through rubber hose or pipe to a collector, where it is removed from the air stream, and the air is then available for recircula-tion in the working place. As during the last few years a number of studies had been completed for the purpose of determining whether or not the dust was effectively removed by the Kadco system, and as the dust counts taken in these tests apparently indicate that it was, the St. Joseph Lead Co. was only inter-ested in obtaining data to show the efficiency of drilling, expressed in terms of minutes per foot drilled, when -using Kadco equipment, in comparison with the former method of drilling dry in a raise and drilling wet in a drift. Comparative dust counts were taken at Balmat, however, by the Metropolitan Life Insurance Co. to show the difference in the dust content of the air in which the operators worked when drilling dry, wet, or with the Kadco equipment.

Jan 1, 1935

By E. Godfrey

The average man one meets on the street thinks of an explosive as a medium of death and destruction, something unstable which should be given a wide berth, because he knows little or nothing about its use or its stability. Briefly, explosives are compounds that develop very large quantities of heat and gas in an extremely short time and in a small space, thereby exerting enormous pressure upon surrounding bodies, and by the rapid expansion of this highly heated gas are able to perform a considerable amount of useful work. The amount of heat generated and the volume of gas produced by the decomposition of an explosive determines the amount of mechanical work it can do, and the time occupied by its change from solid or liquid condition to gaseous condition determines its shattering effect. Explosives manufactured by reputable people are not extremely dangerous, on the other hand they are quite safe if handled in a proper manner. Furthermore, before an explosive can be placed on the Canadian market a sample must be submitted to the Explosives Division of the Mines Department, who may condemn or permit its manufacture, according to their findings regarding its safety in handling and its stability during storage.

Jan 1, 1926

By James T. Staley

Quenching and aging are critical processing steps used to produce precipitation hardenable aluminum alloy products. This work describes personal computer programs that employ models to predict certain properties after quenching and aging and graphically display them. One of the programs allows the user to predict the attainable strength and toughness of aluminum alloy products after an arbitrary quench. Another program simulates the changes in strength and electrical conductivity occurring during second-step aging alloy 7050-T7X products as a function of thickness, furnace temperature set point, and furnace characteristics.

Jan 1, 1993

By Patrick M. Hurley

The spreading-ridge, or accreting plate margin, is the primary conduit of metals delivered to the earth's surface. Isotope ratios of lead show primitive mantle values at these sites, indicating that this is true. We can use lead isotopes in any mineral deposit to indicate the degree to which the metal is "primitive" in the sense of having been uncontaminated with U-enriched crust or "crustal" in the sense that it has been cycling at the earth's surface since earlier times. The reason for this is that the upper continental crust has an enrichment in the ratio of U/Pb over that in the mantle, so that old continental leads have a larger radiogenic component. The primitive metals delivered to the surface at the spreading-ridge are transported on the oceanic plate until they reach a subduction zone. Here they become cycled in the "orogen". However, in this process the primitive metals are mixed with metals from the continent so that the average lead isotope ratios are between those in the mantle and the average upper continental crust. Subsequently a part of the metals in the orogen may become fixed in a new block of continent. However there are processes which continue to uplift and erode ancient continental regions so that there is a continuous feeding back of metals to the orogen. We have therefore a cycling of metals from the existing continental crust into the orogen where they are mixed with new contributions from the spreading ridge and mantle.

Jan 1, 1977

By J. C. Edwards, C. C. Hwang

A computational fluid dynamics (CFD) program was applied to fire spread along combustibles in a ventilated mine entry. The rate of flame spread was evaluated for the ribs and roof of a coal mine entry; timber sets; and a conveyor belt. The CFD program models char forming materials with temperature dependent thermal properties. The program solves three dimensional time dependent flow equations with a mixture fraction model for the gas phase reactions. Radiant heat exchange is evaluated for non-scattering gas. The CFD program predicted a flame spread rate of 0.0145 m / s for an actual coal mine fire in which the estimated flame spread rate was 0.0086 m / s. This overestimated flame spread rate was a possible consequence of the presence of inert materials in the mine entry’s roof and ribs. CFD fire spread rate predictions of 0.043 m / s and 0.73 m / s bounded the measured value of 0.27 m / s for fire spread along Douglas Fir timber sets in a tunnel.

Jan 1, 2006