Search Documents

By Mutombo Nombe, Avimanyu Das, Rick Honaker

Enhanced gravity separators (EGS) provide a more efficient separation than froth flotation when cleaning coal in the 150 x 25 µm particle size range. To improve the performance of an EGS unit, air bubbles were injected into the feed stream in an attempt to decrease the apparent density of the coal particles due to the formation of bubble-coal particle agglomerates. Air injection had a significant impact on operating characteristics and separation performance. Coal recovery was increased by 10 to 20 absolute percentage points while a 2 percentage point drop in the minimum product ash content was also achieved.

Jan 1, 2005

By P. L. Swanson, F. M. Boler

The U.S. Bureau of Mimes conducts research at the Galena Mine, Wallace, ID, with the aim of mitigating the effects of rock bursting. Destress blasting is commonly used as a stress control technique at the mine. A digital seismic array and an array of borehole pressure cells (BPC's) had been installed near the site of a stope undergoing mining and periodic destressing. The instrumentation was being monitored at the time of a destress blast of the 46-99 stope. No significant seismic events occurred coincident with the destress. However, the destress was followed by a 21/2-week period of increased seismic activity, including two damaging events on February 7, 1990, at 034500 (hour, minute, and second) and 122020 Pacific standard time. BPC measurements indicated coseismic ground pressure changes on the order of 200 to 300 kPa associated with the damaging events. Fault plane solutions and dislocation models established that stress changes induced by the event at 034500 may have been significant in promoting the occurrence of the event at 122020. Theoretical investigations suggest that applying knowledge of the existing stress field, an understanding of rock burst mechanics, and fracture mechanics principles can improve destress effectiveness.

Jan 1, 1993

By N. Som

The pile capacity in cohesive and granular soils depends on a number of parameters. The values of these parameters as recommended by Indian Standard Code of Practice vary over wide ranges. A designer often finds it difficult to select appropriate values of these parameters for realistic estimate of a pile capacity. The present paper makes a critical review of the values of the parameters given in Indian Standard Code of Practice and suggests a realistic approach to selecting them in the light of recent research.

Jan 1, 1996

By R. A. Lowe

Smectite is a common impurity in the kaolins of Georgia. This impurity is harmful to the low-shear rheology of kaolin slurries in concentrations as low as a few weight percent. The deleterious effect of smectite on the low-shear rheology is due to the swelling of the mineral. Montmorillonite containing clays were treated to precipitate a compact brucite layer {Mg(OH)2} in the interlayer region of the expandable layer silicate mineral. This treatment forms a hydroxy-Mg-montmorillonite with characteristics similar to chlorite. This treatment effectively reduces the swelling capacity of the mineral and improves the rheological properties of kaolin slurries contaminated with smectite impurities.

Jan 1, 1999

By Jacob T. Wainwright

This stove has been designed to meet the requirements of a fur nave that must be operated with either a reducing or a neutral flame ; and more particularly to make feasible the operating of re duction-furnaces with the cheaper grades of gas-fuel, which has heretofore been impracticable. In general, cheap gas-fuels result from incomplete combustion, and, being suited for further combustion, answer very well for heat ing purposes; and high temperatures may be attained with them, when they are used in conjunction with regenerative stoves. But, in operating a reduction-furnace, a high temperature is not the only requirement. It is also necessary that the fuel shall not be cansumed beyond a certain degree, in order to insure a re ducing flame for the reduction-process ; consequently, it becomes necessary to dispense with combustion as much as possible previous to the use of the fuel-gases in the reduction-furnace. Moreover, these gases must be preheated to a high degree, in order that a sufficient temperature may be maintained in the furnace; and, since this preheating cannot be accomplished by a previous, partial combustion of the gases themselves, it follows that the stoves for pre heating these gases should be heated to as high degree as it is pos sible to attain with an inferior fuel. This result can best be accom plished by complete combustion of the heating gases, and is further facilitated by preheating all of the air and gas used for this com plete combustion. It is more particularly desirable to preheat the air, since the combustible gases used may generally be obtained directly from the furnace, or gas-producer. The reducing gases, escaping from a gas-fuel reduction-furnace, are capable of considerable further dilution with air to secure com plete combustion, and consequently may be utilized for heating the stove to a high temperature, provided the air be sufficiently preheated.

Jan 1, 1889

By Charles H. Thurman

The data given herein were first included in a paper read before San Francisco Section, A.I.M.E., in October 1940, and are applicable to conditions existing until the gold-dredging industry was temporarily suspended by Order L-208 of the War Production Board in the fall of 1942. There is no doubt that gold dredging will be resumed at some future time, and on a scale equivalent to that of the recent past, but the cost data given herein will be affected to some extent by conditions existing at that time, and by labor rates and prices for materials then prevailing. Dragline vs. Bucket-line Dragline dredges should not be considered for mining large areas of low-grade placer gravel. In such deposits a dragline operator with a 5-cu. yd. dragline would be doing well to maintain an operating cost of 6¢ per cu. yd., while a bucket-line dredge with buckets no smaller than 7 cu. ft. each could be operated for less than 4¢ per cu. yd. By operating costs, I mean only field charges such as direct operating and overhead, which includes pay roll, power or fuel, repairs and maintenance, insurance, land clearing and general expenses, but not including such items as prospecting, depletion, depreciation of equipment, State Franchise Tax, or Federal Income Tax. It is not to be inferred that a dragline dredge cannot make a profit in small low-grade deposits, where the extent of a given property is too small to justify the use of the more costly bucket-line dredge. Consider small deposits of 106 gravel. It is obvious that a deposit of 5,000,000 cu. yd. of such gravel could not be mined profitably with a new 7-cu. ft, bucket-line dredge, costing upward of $250,000, and in operation costs at 4¢ per cu. yd., paying for land or royalties out of earnings; nor could a new combination 5-cu. yd. dragline and washing plant, worth upward of $125,000 and working at 6¢ Per cu. yd., make a profit. These comparisons are made because the hourly capacity of both types of dredges is nearly the same. The bucket-line dredge averages 93 per cent operating time in 24 hr., as against about 80 per cent or less for the dragline dredge. These Percentages of operating time are important factors in making a comparison of this kind- The bucket-line dredge has greater efficiency in cleaning soft bedrock, usually characteristic of dredging deposits, and a 7-cu. ft. bucket-line dredge can be efficient to a total digging depth of 80 ft- (65 ft. below water, 15 ft. above). A 5-cu. Yd. dragline dredge is limited to about 30 ft. of efficient digging depth, 5 ft. of which could be above water. In small areas of gravel not over 30 ft. deep, a 5-cu. yd. dragline dredge could make a profit where a bucket-line dredge could not do so. As an example: compare the dredging of 3,000,000 cu. yd. of 10 gravel 28 ft. deep with bucket line, costin 4¢ Per cu. yd., and with a 5-cu. yd. dragline dredge operating at 6¢ Per cu. yd. Because of small yardage, new equipment is not warranted, therefore we can assume that the dredges of both types are used equip-ment, fully depreciated. Dismantling, mov-

Jan 1, 1946

By F. R. Lee

[THE Bureau of Mines was established in July 1910 to conduct research and to Establish standards for mining equipment and practices which would conserve human life, natural resources, and property in the mineral industries. Several lists of equipment approved by the Bureau as permissible for use in gassy coal mines have a been issued since then. The lists covering all approved equipment except breathing apparatus and explosive have been consolidated info two publications: Bulletin 543, Permissible Equipment Approved to January 1, 1953, and Information Circular 5220, Permissible Mine Equipment Approved By The Bureau of Mines During 1953-62. The purpose of this publication is to supplement Bulletin 543 kind Information Circular 8220 with a listing of permissible equipment approved during 1963 and 1964. The schedules (standards) under which equipment listed herein have born approved are as follows (titles and dates of approval and revision are given in footnotes): Schedule 2F,3 schedule 6D,4 schedule 7C,5 schedule 8C,6 schedule 9B,7 schedule 10C,8 schedule 12D,9 schedule 22,10 schedule 24,11 schedule 25B,12 schedule 28,13 schedule 29A,14 schedule 30,15 and schedule 31.16]

Jan 1, 1966

By M Tessier, M Pahkala, L Sletmoe

The Red Lake mine is one of the richest gold mines in the world. The primary mining methods are overhand and underhand cut and fill. Starting in 2003, Goldcorp initiated an expansion program at the mine. The expansion includes a new 6.55 m diameter hoisting shaft currently under construction. The shaft will be driven to a length of over 2180 m. The shaft will be used as a primary ventilation intake to the mine. In addition to the new hoisting shaft, a return air raise is being driven approximately 1690 m from surface. This raise will be a parallel return to the existing mine infrastructure. This paper describes the ventilation and climatic analyses performed in support of the expansion project. The study included a full mine ventilation survey, in situ rock mass measurements, analysing options related to mine layout, airway sizing calculations, air heating options, and climatic simulations. Specifications were prepared for an air heating system and main and booster fans. Analyses were also performed related to heat in the stoping areas namely caused by auxiliary fans and backfill with high cement content.

Jan 1, 2005

By Stevenson I, Dickinson W, Taylor R. N

Despite flash smelting's widespread use little is known about the actual processes taking place in flash furnace shafts and comparatively few reports of sampling campaigns have appeared in the published literature. his paper reviews the previous reports of the use of horizontal trough samplers and analyses their expected collection efficiency. In the light of the deficiencies revealed by this analysis an isokinetic sampler was produced and a vertical sampling technique was also developed to obtain samples from directly below the burners in the shaft of the flash furnace at the Kalgoorlie nickel smelter. Comparison of the sizing of the samples obtained with the horizontal trough and isokinetic samplers confirmed the theoretical analyses and showed that the trough samplers were not collecting the fine particles. Besides providing data to validate mathematical models of the burners and shaft, chemical analyses of the shaft samples showed that the coal in the charge was reacting preferentially and that the plume of at least one of the burners was being deflected from its axial position. In the region directly below the burner there was evidence that the disperser on the burner was imparting more momentum to the coarser particles and that these were concentrating in the outer regions of the particle plumes issuing from the burners.

Jan 1, 1992

By Larry F. Brown

Mining has been the mainstay of the Woods Creek Valley for more than a century. The head of the valley is at the Continental Divide, about 50 miles west of Denver, Colorado. First, it was the quest for gold and silver that drew people to the valley. Then, when molybdenum was classified as a strategic metal by the U. S. Government during World War I, it was the valley's molybdenum mineralization which attracted the most attention. Molybdenum is used primarily as an alloying material in superior grades of steel. Circumstances responsible for providing the label "Urad" are unknown, but Urad is variously reported to be an acronym for "Uranium Research and Development" or "Uranium Research of America Division". The search for uranium was fruitless as no ore grade uranium exists in this area. The moly orebody was first developed and mined by the Primos Exploration Company from 1914 to 1919. During World War II, the mine was purchased by the government and turned over to the Molybdenum Corporation of America to operate. In 1963 AMAX Inc. purchased the property for $2 million. After spending nearly $30 million for exploration and development, AMAX put the mine into production again in 1967.

Jan 1, 1984

By W. J. D. Stone

Many of the common valuable minerals have a magnetic susceptibility which is sufficiently high to render them amenable to magnetic separation. In addition,, many minerals which form the unwanted constituents of an ore can be removed by magnetic means. Magnetic separation in general has suffered seriously from, the lack of a high intensity wet separator. It is only recently that such a separator has become available to the industry. Prior to this, high intensity magnetic separation has been limited to the use of the dry techniques. Since the introduction of the Jones Wet High Intensity Magnetic Separator, extensive test work has been conducted to investigate possible applications. From the investigations conducted and the discussions that have taken place in the industry, it is apparent that the important mineral characteristic of magnetic susceptibility is not receiving the attention that it deserves. Applications for high intensity wet separation are being found in areas hitherto not considered.

Jan 1, 1963

By Yong Yuan, Wenhao Xiao, Luc Taerwe

"The static shear stiffness of an immersion joint subjected to combined compression and shear forces is investigated by experiments in a test set-up. To explore the performance of the immersion joint, the compression-shear loads, which are applied on a specimen according to test protocol, are determined based on real design situation. In this test, the main focus is on the steel shear keys and the rubber sealing. For the applied loading schemes, different levels of axial force, corresponding to the water depth of the joint, are considered as well as the changing amplitudes of the shear force. The force-displacement curve is obtained and the hysteresis is observed during the whole test. The joint‘s static shear stiffness is calculated, showing to increase linearly with respect to the magnitude of the axial force. Moreover, it is found that the rubber sealing has a significant influence on the shear behavior of the joint. INTRODUCTION An immersion joint is the connecting part between two adjacent elements of an immersed tunnel. Compared to that of the bulk elements, the stiffness of the immersion joint is relatively small. When it is subjected to shear actions, whether resulting from vertical foundation settlement or horizontal earthquake movements, shear-resistance of the joint is the main concern for a safe and reliable water-proof design. A flexible immersion joint, which normally consists of a rubber seal and shear keys installed at an element end is a common solution in practice. The way in which the shear keys and the rubber seal behave in the joint together is of vital importance to a comprehensive understanding of the shear behavior of the joint. However, in literature very few experiments on the shear behavior of immersed joints are available although the flexible joints are applied in practice for more than 50 years already. O. Kiyomiya (2004) carried out both a 3-dimensional experiment and a finite element analysis for a new type of flexible joint referred to as the Crown Seal. The results indicated that this new type of joint can be applied in practice because of the effective reduction of lateral deformation. A linear model was found in the paper of Anastasopoulos et al. (2007) to describe the behavior of the shear keys, which consider that the stiffness of the shear keys tends to infinity. R.S. van Oorsouw (2008) discussed the shear capacity of concrete shear keys in segmental joints, by analyzing the influences of reinforcement and friction force between shear keys."

Jan 1, 2016

By Vasile Murariu, William Pate, John Herbst, Dilek Alkac

"Multiphysics models are essentially first principles models capable of providing very accurate micro scale predictions. The computational requirements for Multiphysics Models are extensive, precluding their direct use for flowsheet simulations. Population balance models get their form from theory but the model parameters have to be provided from experiments. The prediction errors for the population balance models are typically significantly higher than those for the Multiphysics Models but the computational effort for Population Balance Models is typically much less than that for the Multiphysics models. The hybrid model described here takes advantage of the strengths of each of the two primary model types and minimizing the weaknesses of each. The Multiphysics Model is used to perform high accuracy "experiments" that are difficult or impossible to conduct in laboratories or plants. The results of these experiments are combined with standard laboratory or plant data to parameterize and further enhance the Population Balance portion of the hybrid model. The creation of a useful Hybrid Model is demonstrated for a MP1000 secondary crusher. The validation of the hybrid crusher model is also presented. Finally the use of the Hybrid Model is illustrated in a full comminution flowsheet simulator."

Jan 1, 2014

By Z. Q. He

This paper introduces the structure and working principle of SLon magnetic separator that has excellent performance in iron removal, and summarizes a part of the examples of applications, which applies this machine to remove iron from non-metallic ores, and shows widespread prospect of application of this machine in the purification of non-metallic ores.

Jan 1, 2014

By Isobel Yeo, Florent Szitkar, Sven Petersen, Sebastian Graber, Meike Klischies

Technological advances and the shift towards green energies in the last decades have led to a substantial increase in the demand for metal resources. With rising political tension, and quasi-monopolistic production of some key metals, a secured supply chain cannot be guaranteed [1]. Therefore, the focus of the international research community and mining companies has expanded to the seafloor, looking for additional resources. The seafloor may have the potential to contribute significantly to a secure metal supply in the future. However, we have only investigated a fraction of our oceans in sufficient detail to assess the global resource potential. A detailed exploration of the vast seafloor is currently economically not feasible, due to its extremely time-consuming and costly nature. Seafloor massive sulfides generally form along the active plate boundaries and at active volcanoes in arc settings. However, the resources are not evenly distributed on the seafloor. Large deposits tend to be more common along slow-spreading and ultra-slow- spreading ridges that make up the majority of the global mid-ocean ridge system [2]. Therefore, it is important to establish geological models and exploration criteria in order to narrow down the permissive areas, which are likely to accommodate economically interesting deposits. Based on a detailed study of the TAG hydrothermal field in the central Atlantic Ocean, hosting a large active mound as well as several inactive mounds, we develop exploration methods and criteria to define areas of potential massive sulfide occurrences along slow-spreading sections.

Jan 1, 2018

By Robert H. Merrill

A method of determining the strength of a mine roof layer in place is described in this report. The method was tested on a limestone roof layer 50 feet wide, 100 feet long, and 20 inches thick. In place measurements were accomplished by introducing air under pressure into a separation between the layer and the overlying roof, and as pressure was increased, the corresponding strain and deflection of the roof layer were measured until the roof failed. The ultimate strength of the roof agreed with the tensile strength of the roof rock (modulus of rupture) as determined in the laboratory; the modulus of elasticity as measured in place did not agree with the laboratory-determined values; the deflection and tensile strain in the layer in place showed good agreement with the theory of a body-loaded beam clamped at both ends. This procedure for determining the strength of a mine-roof layer is safer and less costly than successively widening a roof to failure. For example, it would have been necessary to mine the room to a width of 114 feet and a length of 228 feet to produce failure in this roof layer. The method is not necessarily limited to limestone; any thinly bedded rock type can be tested by this procedure when there is an open parting over the mined area.

Jan 1, 1958

By John Nagy

Results of initial research by the Bureau of Mines are given on the dust explosion hazard of float coal and on the related factors of occurrence, rate of production, sampling techniques, transport, and deposition of float coal. Tentatively, it is suggested that where float coal deposits prevail, a mini-mum of 80 percent incombustible be maintained in the top 1/8-inch layer to neutralize the explosion hazard of the surficial coal deposit.

Jan 1, 1965

By Edward T. Koch

With the dramatic increase in world demand for basic raw materials, open pit mining is proceeding at an unprecedented rate. A viable demand is the ever tempting Siren's song for increased production or new facilities. When the Siren's lure is viewed against the panorama of today's world economic milieu the concomitant Scylla and Charybdis are seen in the form of high capital cost and high operating cost. If the economic realities of present day open pit mining are to show a proper return on investment, a clear and penetrating eye must be cast upon the area of mine planning. This paper deals with the problem of overburden removal. In almost every open pit mining operation overburden removal is a significant part of the capital cost and operating cost of the total operation. This paper deals with a new and unique method to affect economical overburden removal. Well known to all are the parameters surrounding draglines, shovels, and bucket wheel excavators. All of these machines require a reasonably stable soil to support them and the shovel and bucket wheel excavator require a reasonably stable bank in which to operate. Their reliability, portability and rate of production per dollar of invested capital are good.

Jan 1, 1975

By William Kent

Mr. ASHBURNER's paper on the Classification and Composition of Pennsylvania Anthracites, read at this meeting, well shows the need of new and accurate determinations of the heating value of these coals. A similar need exists for the determination of the value of bituminous coals, since the variation in quality of the latter is greater than the variation in anthracites. The recent extensive use of liquid and gaseous fuels, " patent" fuels, tan-bark, and other refuse fuels, also makes a necessity fix some correct method of determining the relative values of each of these fuels. Mr. Ashburner has recommended that tests of coals should be undertaken by the Second Geological Survey of Pennsylvania, and Professor Dewey, as stated in Mr. Ashbnrner's paper, has suggested a plan for tests of American coals, by the Smithsonian Institution, for which an appropriation by Congress will be asked. It is to be hoped that if any extensive series of tests of coals is carried on under either Government or State auspices, the erroneous methods of test which were followed by Professor Johnson in 1842, and by Quartermaster-General Meigs in 1882, will not be adopted.* The first requisite in determining the heating-power of a fuel is proper apparatus, such as has not been used in any of the tests of American coals yet reported. In the hope that more accurate means may be used in future tests, the writer desires to call attention to an apparatus which he has designed for the purpose. Not having had opportunity for making a trial of it, nor even of having it criticised by others, he does not offer it as the best possible apparatus; but if it contains any points of value, and leads to the design of still more suitable devices by others, the object of the presentation of this paper will be accomplished. The tests by Professor Johnson and General Meigs were made by evaporating water into steam in ordinary steam-boilers. A steamboiler of ordinary construction is not a good apparatus for determining the heating power of a fuel, for the following reasons:

Jan 1, 1886

By Nirmal Weerasekara

Mill liners serve the dual purpose of protecting the shell from wear and transferring the rotary motion of the mill to an effective grinding action. As the liners wear, the efficiency of energy transfer changes, so there is balance between liner profile for wear and for milling efficiency. A tool that can simultaneously predict the evolution of the liner profile and the associated change in milling efficiency should prove most useful in optimal liner design. This paper presents such an approach, based on measured 3D liner profile data informing 3D DEM simulations of charge motion and liner wear modelling.

Jan 1, 2012