Search Documents

By Rainer Alles, Markus Keller

INTRODUCTION For overland conveyors of several kilometres length and as well as wide for conveyors designed for high mass flows, the cost for the conveyor belting share is 40% to 50% of the invested cost 173. The German Standard DIN 22101 is used for calculation and dimensioning of - conveyor belts and belt conveyor components. Developments in rubber technology and conveyor belt design required a revision of the standard released in 1982 121, which was published in August 2001 131. New research results and publications 16-9, 13-15] led to a better understanding of the material behaviour and their influences on conveyor belts. Test and calculation methods have been established to determine the most important parameters which are related to the performance of a conveyor belt line. These parameters are • The running resistance of the idlers • The indentation resistance of the belt • The dynamic splice efficiency • The distribution of belt load in the splices, transition zones and on pulleys. As a result, new rubber compounds with low indentation losses allow the use of reduced friction coefficients and thus lead to reduced power consumption, smaller drives and lower belt tensions. The deeper understanding of the flux of forces within belt splices led to both optimised splice design and optimised rubber compounds which significantly improve the dynamic splice efficiency. Therefore, in accordance with the standard, the benefits of these technologies and the better understanding of material behaviour allow a reduction of belt strength still maintaining sufficient safety factors. Thus engineers are enabled to calculate belt tensions more exactly and users are encouraged to pay more attention to starting and braking techniques. DETERMINATION OF DRIVE FORCE According to the DIN standards the resistance to motion generally has to be determined for each different section of the belt conveyor including upper and lower run separately. The necessary drive power P is calculated as [ ] with v as the conveying speed. The total of all resistances to motion of carry and return run can be determined as [ ] FHo and FHu are the primary resistances consisting of the running resistances of the idlers, the indentation resistance of the belt, the fulling of the conveyed material and the flexure of the belt. While indentation resistance and idler resistance are measurable, they have been deter- mined to be responsible for up to 70% of the primary resistances covered by FH. Further FN is the secondary resistance that covers, for example, the resistance of feeding points and scrapers. Fa are the total slope resistances and Fs is the total of all special resistances, resulting, for example, from belt steering devices. These three resistances should be neglected in the following discussion. For conveyors where a determination of the substantial parts of the resistances to motion is not possible, according to the new DIN standard [31 a determination of the drive power is acceptable by using the fictitious friction factor) [ ] In this formula the index i identifies the individual section of the conveyor, 1 is the length of the section and MR, MG and ML are the related masses of the idlers, the belt and the load in kg/m. The fictitious friction factor f determines the ratio between the overall resistance to motion and the total of moved masses within the

Jan 1, 2004

By R Dunne, W McCallum

Continuous improvement might be defined as seeking incremental improvement over time through improved equipment, processes, technology and the efforts of people. Most people working in ore processing facilities embrace the general principles of continuous improvement. However, given the industry-wide issues with skilled personnel and the constantly changing environment in ore processing facilities, it is often difficult to identify improvements in a facility over a given time period. The driver for these outcomes is the use of basic principles and technology to achieve best practice targets. The process involves four stages: develop standards of practice to define best practice in specific areas; write procedures to guide the organisation towards these best practices; implement the procedures and develop a review process to provide a method of measuring performance against best practice.By reviewing performance against best practice on a regular basis, the organisation measures progress towards the best practice targets and the incremental improvement between these regular reviews is a measure of continuous improvement.This paper provides the background for developing standards of practice for metal accounting, metallurgy and metallurgical management. The paper also describes how standards of practice can be used to develop continuous improvement and the skills set of the departmentÆs leadership team.CITATION:McCallum, W and Dunne, R, 2012. Metallurgical management tools for continuous improvement, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 225-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Björn Johansson

"SUMMARY Every tunnel designer has to consider the power of water ingress when designing a new tunnel. Either you choose solutions with simple methods to divert the ingress water or a robust system with the intention that it will give gain on low maintenance costs and a long lifetime. This article describes a new method to divert ingress water in a robust way and more economical than traditional concrete lined tunnels. This system is based on a bolt grid suspending a water tight membrane, which is reinforced and covered with sprayed concrete. The method has been in limited use in Sweden since 2005 and with continuous improvement, still going on, it is now applied for the large project “Stockholm Bypass”, a 21km long highway project. TUNNEL MAINTENANCE RELATED TO WATER INGRESS The Swedish Transport Administration maintain approximately 190 various tunnels that is constructed by a number of different methods, (Swedish Transport Adm 2015). Commonly the ground conditions are good and fairly low ground support is needed. Contrary water and winter conditions can be sever, which gives high impact onto the tunnel design and in particular methods to protect against “frost and water ingress”. During a tunnels lifetime it is common that maintenance related to water ingress occurs several times and sometimes frequent occasions every year. Such maintenance costs and consequences of lost open time for the tunnel can rapidly become higher than the initial cost of the tunnel. Thereby it is obvious that spending time during design to evaluate requirements for a suitable system against water ingress is preferred. Icicles Icicles are formed when water is below freezing degrees and drips or run from an ingress point. At very cold conditions also water flows running at high velocity freeze into ice and a rapid growth can appear. If the integrity of the tunnel traffic area is interfered by icicles they urgently have to be removed before they cause an accident. Typically the tunnel or a part of the tunnel must be closed to do such maintenance. TUNNELS FROST AND WATER INGRESS PROTECTION IN SWEDEN In Sweden methods to perform “frost and water ingress protection” are primary developed for drill and blast tunnels as it is most common tunneling method. The foundation Swedish Rock Engineering Research has done a comprehensive report SveBeFo Rapport 77 that describes water and frost prevention in Swedish tunnels up to year 2005. Below is only slight description of those various methods. Lately some more attention is paid to concrete lined tunnels made by TBM since TBMs successfully built water tight tunnels in City Tunnel (Malmö) and Hallandsås Project. When environmental demands require maintained ground water levels, water tight tunnels made by pressurized concrete lining becomes more economical and on the same time also becomes protected from icicles and water drips."

Jan 1, 2016

By Yousef Mohassab, Feng Chen, Hong Yong Sohn, Mohamed Elzohiery

The determination of reduction degree in a DR process is sensitive to the total iron in the ore and DRI. An accurate and high throughput analysis method for total iron has been developed. Titration of the solution after tin(II) chloride reduction of ferric ion is a widely used method for iron analysis. However, it is a multistep method that requires many chemical reagents and much time. In this work, an ICP-OES analysis method with higher or equivalent accuracy compared with the titrimetric method was developed. This method has much higher throughput and demands fewer chemical reagents compared with the titrimetric method. In this paper, a comparison of the two methods is presented.

Jan 1, 2016

By Colin Barratt

The East Side Access (ESA) project is the largest underground rail infrastructure project under construction in New York City, USA. The Manhattan segment of the project is to be mined through rock and consists of 4.1 miles of Tunnel Boring Machine tunnels for track work and mined excavations to house rail switches, air plenums, and other rail facilities. This paper considers different methods for concrete lining, such as the use of fixed forms, adjustable forms, and pneumatically applied shotcrete. The advantages and disadvantages of these methods are discussed and the basis for considering one over the other are illustrated. Further discussions on design development and preparation of documents to facilitate quality and constructability in the field are presented.

By C. J. Cajka

Commodity agreements, trade liberalization, producer cartels, the New International Economic Order, price stabilization and access to supply are buzz words of the day. The international concern and dialogue on these concepts, often by a new breed of politically motivated experts, have generated intense interest in seeking an international solution to natural resource problems. While this momentum was maintained during the past year, the growing incidence of protectionist actions by several major nations has been eroding confidence in the global approach. The seriousness of current difficulties has created an urgent need for decisive action. At the same time, the limitations of the global approach have become more evident.

Jan 1, 1978

By Jean Scott, G. A. Collins, G. W. Hodgson

WHILE it is well known that trace metals in crude •oils and distillates have been a matter of deep concern to refining engineers because of the damage done .by the metals to cracking catalysts and refractories (8, 5), the trace metals in crude oils may be of great benefit in correlation studies and in origin studies. During the geological processes in which the oil is formed from •animal and vegetable life, the hydrocarbons are subjected to a host of inter-related reactions, both physical and chemical. It has been well demonstrated that the lighter materials, certainly the short-chain paraffin hydrocarbons, are degradation products of the heavier molecules, and it might be concluded that for correlation studies it would be advisable to direct attention as much as possible not to the degradation products of the large molecules but to the large molecules themselves. Be this as it may, the methods at •hand to conduct the study are not particularly precise and, in the past, attention has centred on the simpler small molecules, as evidenced by the great mass of work involving distillation and chromatography with painstaking separation of the simpler 'front-end' hydrocarbons.

Jan 1, 1954

By William J. Schloemer

INTRODUCTION The history of coal mining the Ostrava Region of the Czech Republic goes back nearly 250 years. Both coking coal for steelmaking and thermal coal for the production of energy are mined here; however, it was the coking capabilities that subsequently turned the region into a major steel-producing area in the early 1800?s, something that continues to this day. Ostrava lies in the northeast corner of the Czech Republic, near the southern border of Poland, and falls within the Upper Silesian Coal Basin. The region contains over 400 seams of coal of which about 150 have been mined over its history and continue to be mined. Eighty percent of the Upper Silesian coalfieldlies in Poland and is presently mined by about 35 coal mines; the remaining 20% falls in the Czech Republic, which presently has four mines operated by OKD, a.s., a subsidiary of Amsterdam-based New World Resources. Traditionally, all the mines in this region have employed the longwall method of mining, of which subsidence is an unavoidable consequence. In fact, due to the long history of longwall mining here, there are areas where the overall subsidence has exceeded 37 meters (121 feet). The region is fairly densely populated with residences and industry, and a considerable amount of coal lies under some of these areas where subsidence is not allowed or has to be minimized. It is this reason that has driven OKD to consider alternate methods of mining that will not create subsidence. The decision was made to consider the room and pillar method of mining in order to leave stable pillars of coal to support the surface. After considering several locations, OKD chose the shaft safety pillar at the CSM mine as a test mining location. To say the least, this is a very challenging location in which to conduct a test. As with the entire region, there are many faults from tectonic activity, the seams are pitching at 12 to 20 degrees, the area is affected by high horizontal stress, and the depth of 750 to 900 meters is perhaps the deepest room and pillar coal mining ever attempted.

Jan 1, 2014

By S Watson, L Martinez

Mine projects are complex opportunities that demand a constant assessment of uncertainty, ie risk and upside potential. This is because the value of a mine project is typically influenced by many underlying economic and physical uncertainties, such as metal/mineral prices, metal/mineral grades, costs, schedules, quantities, and environmental issues, amongst others, which are not known with much certainty at the beginning of the project. But, is uncertainty an enemy or an ally of the mine planner/analyst? To answer this question, this paper first assesses and elaborates upon the general concept of uncertainty. It then looks at the different sources of uncertainty in a mining project, such as the orebody, costs and product price uncertainties, and their effect on the final project value. Next, a general?review?of current mine evaluation techniques highlighting their limitations when dealing with uncertainty is made. Finally, an extended evaluation and risk management framework that addresses the existing uncertainty in the (greenfield/brownfield) mine evaluation process is proposed. One important characteristic of this framework is that it uses and manages uncertainty in order to generate additional value to the project; this is done through operational and managerial flexibility, which allow mine planners to minimise/maximise project risk/upside-potential giving a more realistic estimate of the projectÆs market value - this is shown in practical and simple examples occurring at different stages of a mine project, such as exploration and operation. Final conclusions are provided at the end.CITATION:Martinez, L and Watson, S, 2012. Uncertainty - An important source of (additional) value for mine projects, in Proceedings Project Evaluation 2012 , pp 131-140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By V. Schwinn, P. Fluess, N. Cauderlier, J. Bauer

From a strategic and economic point of view, the development of fine grain high strength steels for long distance pipelines is intensified world wide to satisfy the demand for natural gas in the future.The project related property profiles based on strength, toughness, crack arrest and sometimes resistance against HIC at defined design temperatures require an effective structural refinement using advanced steelmaking and processing in the rolling mill. The microstructure of modern line pipe steels ranges from ferritic pearlitic to ferritic-bainitic and structures where bainite is the dominant component, possibly upgraded by secondary phases. This paper illustrates microstructures and properties of recent orders on line pipe steels both for onshore and offshore application using different processing routes in the plate mill. Examples will be given for SAWL 485 offshore grades, X65 HIC and X70 HIC onshore grades, respectively. Finally, production results of a recent X80 order will be presented.

Jan 1, 2005

By J Hadjigeorgiou

Narrow vein mining, as most types of mining, faces important geotechnical challenges. The specificity of geotechnical challenges in narrow vein mines stems from the nature of the deposits, which are often inclined, discordant and found within fractured rock or faults or in shear zones within country rock. This complicates the construction of representative geomechanical models and limits the applicability of several engineering design tools. Furthermore, in certain cases, the severity of encountered geotechnical problems is considerably greater in narrow vein than in wider orebodies. This paper provides an overview of geotechnical and other challenges in narrow vein mines with a focus on how these are currently addressed. Of particular concern is the use of manual labour working close to the mining face where there is greater exposure to geomechanical hazards. This review concludes with a particular emphasis on understanding the limitations of commonly used engineering tools and techniques to address geotechnical problems in narrow vein mines.CITATION:Hadjigeorgiou, J, 2012. Geotechnical challenges in narrow vein mining, in Proceedings Narrow Vein Mining 2012 , pp 15-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By S. Behera, K. Dey

This paper presents a methodology for finite element (FE) modelling to analyse the total deformation of rockmass under blast-load, with a focus on predicting backbreak that may occur during surface blasting operations. Backbreak can result from improper use of explosive energy, leading to damage beyond the excavation zone and jeopardizing operational safety and productivity. The paper highlights the impacts of backbreak on bench stability, excavator operation, drilling operation, flyrock generation, and improper fragmentation and boulder formation in surface blasting. However, prior estimation of extent of rock breakage zone can provide an idea to formulate the blast design to control the backbreak. While vibration-based prediction models are commonly used to estimate backbreak, they require physical blasting experimentation. To overcome this limitation, the paper describes the development of a FE model using ANSYS Explicit dynamics, which simulates rock blasting and calculates the total deformation of the rockmass. The rockmass deformation is modelled using Drucker-Prager (D-P) strength model with the Jones-Wilkins-Lee (JWL) equation of state for the explosives. The accuracy of the FE model is evaluated through physical experiments, and the results are compared with the vibration models. The FE model demonstrates close proximity to physical observations as well as vibration model result in predicting backbreak, thereby offering a promising alternative to vibration-based prediction models. The primary objective of the study is to predict the response of the insitu rockmass to explosive blast loading and determine the effective rock breakage zone.

Jan 1, 2024

By John Johnston

ONLY two of the Institute's 26 Local Sections were unrepresented at the delegates' three sessions, held on Monday morning and afternoon and Thursday afternoon of the annual meeting. The Philadelphia and Wyoming Sections alone sent no delegates. In all, seven hours were spent most profitably in reviewing the work done by the Institute at headquarters and in the field, comparing ideas and practices in varied activities, and in establishing personal contacts. Cordiality and the co¬operative spirit marked the meeting and apparently no one had any serious grievances to air. Four motions were introduced and unanimously passed. The first, which was introduced by B. L. Sackett, was a recommendation by the delegates that a national committee be appointed to cooperate with Local Sections in the matter of student activities, to promote Institute welfare. It was agreed that this recommendation be made simultaneously to the Board of Directors and to the Mineral Industry Education Division. A subsequent resolution by A. M. Smith was passed asking that a part of the duties of this committee be to secure the opinions of Local Sections as to the most desirable methods of interesting students in the preparation of technical papers, by giving prizes or otherwise, and to report their findings at the Section Delegates' meeting next year.

Jan 1, 1933

By Charles G. Kemsley

IN view of the truly remarkable development of special steels for special purposes, the mining industry has for years looked forward to a time when steel makers would come forward with a product which would be an improvement over the straight carbon steel which has always held the field for drilling rock. In order to avoid making changes in conventional shop practice, the industry has perhaps been too insistent upon obtaining a water hardening steel which could be handled in the blacksmith shop by long established methods. As early as 1932 or 1933, an oil-hardening tool-steel of the one per cent carbon, plus chrome, plus molybdenum type was applied to hollow drill steel. It was known as a hard as well as a tough steel, and one that, theoretically, should give a good account of itself as a rock drill, if properly heat-treated; and so it has proved in actual trials. There were numerous deterrents which retarded adoption of this steel. For several years there has been a constant improvement in the drilling qualities of the straight carbon steel, and, considering the higher unit price ? of the alloy, there has been considerable doubt in the minds of some mining? men as to what advantage there might be in the use of alloy over straight carbon for hollow drill steel. The alloy being an oil-hardening steel, its adoption meant having two kinds of steel in the mine, for a time, and that spelled trouble, unless some positive means of identification was adopted. The hardening and forging ranges of alloy steel being narrow also made necessary much closer control over these operations if poor results were to be avoided. These thoughts undoubtedly prevented its use becoming wide-spread, for, as a matter of actual record, less than fifteen per cent of all the hollow drill steel used in Canada today is alloy.

Jan 1, 1942

By Robert P. Vinson

A sequential sampler, based on the Archimedes screw, has been developed by the Bureau of Mines. Its initial purpose was to collect air samples during tracer gas studies in underground mines. However, the basic concept can be applied to other sampling needs, including sampling of liquids. A prototype was built and successfully tested in the Bureau's Experimental Mine at Bruceton, Pa. The simple design makes the sampler inherently durable and low in cost.

Jan 1, 1976

By George O. Lower

The use of cyanides in the extraction of gold and silver is well known.1 Such extractions employ con¬centrations of cyanide in the range of 0.02-0.25 % sodium cyanide equivalent in leaching cycles of 24-48 hours and frequently longer. Copper minerals, even though minor components of precious metal ores, dissolve in these cyanide leaching solutions, consume cyanide, cause fouling of mill solutions, and thus interfere with the precipitation and recovery of gold and silver. 2,3,4 This paper presents a summary of laboratory investigations on the use of cyanide solutions as extractants for copper from various copper-bearing ore fractions. In view of the metal contents involved, it will be apparent that larger quantities of cyanide are required to extract copper than for the extraction of precious metals. In cyanide solutions of concentrations generally favorable to copper extraction, sulfide and oxide copper minerals were found to dissolve rapidly at room temperature and atmospheric pressure. For example, on products in the flotation size range, the major portions (e.g. 65-85%) of the extractable copper frequently dissolved in 2-10 minutes. At coarser grinds, e.g. 100% minus 28 mesh and 100% minus 10 mesh, 75-85% of the total copper was extracted in 30 minutes.

Jan 1, 1966

By Keulla Venya Urbano e Silva, Marcelo Quintão e Silva Marchetti, Rafael Silva Marcelino, Rafaella Bicalho da Rocha

Comparative study between standard and BigFLUX matrices for high intensity magnetic separation pre-concentration (WHIMS) stage for iron ore. The evaluation was carried out on GAUSTEC’s pilot equipment for samples from Viga Mine’s operation. Samples in different feed iron content on rougher stage were evaluated in 46 experiments with matrix variation. The analisys compared chemistry, mass recovery and metallurgical recovery results to define the most efficient matrix to use in a pre-concentration stage.

Oct 3, 2019

By N. M. Komkov

The main operation of obtaining zinc from sulfide raw materials by hydrometallurgical technologies is the oxidation roasting of zinc concentrates in fluidized bed furnaces. The technical-economic parameters are determined by the parameters of the roasting process, which depend on the composition of the initial raw materials, the temperature of the bed and on other factors. The predetermined roasting temperature is maintained due to the change of specific efficiency as well as to the quantity of the heat removed from the bed. The efficiency of caissons depends at a high degree on the composition and the thickness of the accretion formed on the surface of the caissons. Forecasting the roasting results is impossible unless we know the mechanism of the accretion formation. The aim of the present paper is the thermodynamic analyses of the behavior of the charge compositions under roasting and the determination of the potential mechanism of the accretion formation. The thermodynamic analyses show that under conditions of the oxidation roasting the thermodynamic probability of the formation of zinc sulfate is higher than the probability of the oxide formation until a temperature of 873°K is reached. The thermodynamic probability of the formation of the lead sulfate is higher than the probability of oxide formation in the entire temperature range of roasting. The probability of formation of ferrites and silicates of zinc decreases only insignificantly the sulfate stability. The results of the investigation of the accretions composition formed under roasting of concentrates with particle sizes less than 0.02 um (60%), containing 65% of sphalerite (ZnS), 12% of pyrite and chalcopyrite (FeS2 and CuFeSz2 each, 3% of galenite (PbS), 7% of silica and other non-ore minerals, have shown that the composition of accretion varies depending on the depth of the accretion layer. The accretions on the caissons and the thermo-siphons consist mostly of zinc sulfate (more than 50%). The accretions of forchamber consist mostly of zinc oxide. They also contain ferrites and silicates. The formation of the sulfate zinc accretion in the cold parts of the fluidized bed furnace (the caissons and thermo-siphons) may be explained by a lower temperature on the surface and probably by a catalytic influence of the present oxides in the formation of S02 and sulfates. The nature of the structure of the accretion in the hotter parts of the furnace may supposedly be explained by the formation of elemental vaporous zinc during roasting.

Jan 1, 2003

By GEORGE S. POPE

The purchase of coal by the Government under specifications depending on the heating value of the coal, its content of ash and of moisture, and other considerations, rather than upon the reputation or trade name of the coal, was based on the fuel investigations begun by the Technologic Branch of the United States Geological Survey in 1904. The plan was first adopted by the Treasury Department in 1906. Since then the plan, variously modified in form but the same in principle, has been gradually adopted by other departments until at present of the coal used by the Government, the total value of which approximates $8,000,000 annually, more than half is purchased under specifications. The Government publications dealing with the adoption by the Government of the specification plan, the number of contracts awarded on that basis, and the quality of the coal delivered under such contracts in the several fiscal years covered by the reports are given in publications listed at the end of this bulletin. Under the authority of acts of Congress making appropriations for analyzing and testing fuels belonging to or for the use of the United States Government, a laboratory is maintained at the headquarters of the Bureau of Mines, Washington, D. C., where samples represent- ing deliveries of coal purchased under specifications for Government use are analyzed and tested. At this laboratory more than 1,200 samples have been analyzed and tested in one month. With the complete equipment and the efficient force employed, the analytical work has been so perfected that the analyses and heating-value tests of the samples received are as accurate as may be reasonably expected in laboratory work of this nature. One of the serious drawbacks to the general adoption of the speci- fication method for the purchase of coal is the difficulty of obtaining at reasonable cost samples of coal that can be considered fairly repre- sentative of the commercial product delivered in wagons, railroad

Jan 1, 1913

By O. F. Brown

Excavation and loading are primary operations in the surface mine production chain, constituting a significant component of production costs. This makes excavation and loading important cost centers that need to be improved to lower production costs. Optimizing the design and use of excavators will improve energy efficiency in earthmoving operations, and this requires a thorough understanding of the soil-tool interaction process. Modeling the interaction process accurately is the key to this optimization. Experimental and analytical methods have provided limited information on the behavior of soils during excavation. Finite element (Fe) analysis of soil-cutting blade interaction produces some advantages over experimental and analytical methods. However, the soil constitutive equations used in most of the available Fe analyses fail to adequately model the plastic behavior of the soil. This work uses Fe modeling to study the behavior of formation-cutting blade interactions in dozer excavation. The formation is modeled as a nonlinear elastoplastic material using the modified cam-clay (mCC) model. The model accounts for soil-tool interface friction, and progressive and continuous cutting at the blade tip. The results provide soil forces, a progressive developed failure zone and soil displacement fields. The sensitivity analysis of changes in blade angle on cutting force shows that the cutting force increases with increasing blade angle. The cutting depth of the blade had a similar effect on blade cutting force. Increasing the depth of cut increases the required cutting force. Increasing the coefficient of friction at the soil blade interface increases the blade cutting force. Reducing the coefficient of friction at the soil blade interface from 0.3 to 0.05 reduces the cutting force by 22.3%. The percentage represents the maximum potential savings in blade cutting force. This research initiative advances the frontiers of soil-tool interactions during excavations to expand the limited knowledge in this critical area.

Jan 1, 2012