Search Documents

By David A. Newman

The Geomechanics Classification (Bieniawski, 1979) was modified for entry and roof support design in underground room-and-pillar coal mines. Adjustment multipliers were introduced to incorporate the influence of strata weatherability, high horizontal stresses, and the roof support reinforcement factor into the existing classification system. Sixty-two case histories of both standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant impact upon the supported stand-up time of coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1985

By Mohammed Sakr

This paper presents the results of a full-scale axial compression and tension (uplift) testing program executed on large-capacity helical piles installed in very stiff to very hard clay till soils (i.e. cohesive soils). A total of ten tests including six axial compression tests and four tension (uplift) tests were carried out. The results of the axial compressive and tensile pile load tests and field monitoring of helical piles with either a single helix or double helix are presented in this paper. Helical piles are traditionally used to support light to medium loads (i.e. loads up to 500 kN or 56 tons). However the results of the present study confirmed that helical piles can support significantly higher axial compressive loads up to 2450 kN or 275 tons, which is about 5 times traditional design loads. The study also demonstrated the high tensile capacities of helical piles which was as high as 85% of their compressive capacity. Hence helical piles can provide a viable design option for foundations supporting relatively heavy loads.

Jan 1, 2012

By Vern L. Kegler

This paper is one off a series dealing with mining methods and costs, sponsored and published by the United States bureau of Mines. ACKNOWLEDGMENTS The author acknowledges the, constructive and helpful suggestions and criticism of W. F. Lamoreaux, vice-president, and general manager of the Ducktown Chemical & Iron Co. United States Geological Survey Professional Paper- 139, by W. H. Emmons and F. B. Laney, has been drawn upon for some of the information contained in the paragraphs or history and geology.

Jan 1, 1931

By R. J. Sweigard

Deep tillage is used widely as a Means of alleviating excessive soil compaction. There has been some concern that the voids created by deep tillage may collapse before a more natural soil structure develops, resulting in recompaction subsequent to deep tillage. A laboratory investigation was conducted to determine the feasibility of pneumatically injecting organic material into the voids during deep tillage to prevent any significant recompaction from occurring. Various amendments were injected into the soil in the laboratory using a small-scale ripping and injection system. Measurements were made of selected soil properties to evaluate the feasibility of this method.

Jan 1, 1993

By J. Kretschmann, N. Nguyen

"The Vietnamese economic growth of more than 5% per year leads this country to an enormous demand for raw materials. In the duration of ongoing expansion, the big challenge in the coming decades will be to make this process as sustainable as possible when it comes to economic, environmental and social objectives. Risk management especially in occupational safety and health (OSH) in enterprises is one of the most important tools to achieve this aim. But until now, this has not been taken into priority by Vietnamese coal mining enterprises. Main reasons for this situation can be found in deficient legislative conditions and in non-synchronized risk management systems. In contrast, Germany has implemented an adequate legal system and the German mining industry has gained lots of experiences in risk management, especially in occupational safety and health. This paper seeks to point out specific challenges how to improve occupational safety and health in Vietnam by transferring and applying German methods and standards."

Jan 1, 2011

By C. P. Wa1ters

This paper is written primarily from the standpoint of the miner and consumer of Missouri fireclays in refractory products, principally firebrick used in the linings of blast furnaces, hot metal transfer cars, the recuperators of glass melting tanks, and other allied uses involving contact with liquid metals and reactive slags. For these uses the manufacturing plant requires forecast of certain physical characteristics, as well as chemical characteristics, of the raw clays as a determination of practicability of mining, treatment such as pre -firing or calcining, and final usage area. These methods and results may leave something to be desired from an academic view, but are used my operation as an on-running guide to seeking and mining raw material. The high quality fireclays of Missouri are generally differentiated by the user as the softer, somewhat plastic, "bond" clays and the so-called flint clays suitable for a fired or unfired aggregate portion of a brick composition. The semi-plastic "bond" clays are mined in a producing area of northeast Missouri including Montgomery, Audrain, Callaway, Monroe, and Lincoln counties. In this geographic area the clays are the members of the cheltenham formation and occur in rather large lenses in which the usable members may approach 15 meters in thickness and an area of 6o to 8o acres. Overburden is dependent on the surface topography and, in our operations, varies from 8 meters to 25 meters. It can be up to 36 meters in the prairie uplands, but this is rarely strip mined. There was former mining by shaft and drift methods in which the overlying coal was also worked. These clays are primarily used as a binding material for other clay aggregates and is characterized by its lower refractoriness-cone 3o (165o c) to cone 321/2 (172o c), in terms of pyrometric cone equivalent, and an alumina - Al2o3 - content of plus or minus 31%. Physically, these clays are readily slaked by water to a fine grain size and exhibit a degree of

Jan 1, 1977

By Ad. Breyre

[Internal-combustion engines have been used in Belgian mines for a long tine. As early as 1899, the use of these engines underground was considered, but the general policy was to prohibit such an application unless ministorial permission was granted' in special instances. At that time only gasoline engines were available, and a few of these were installed as stationary engines, although in general they were replaced later by electric or compressed-air motors. However, the number of gasoline locomotives continued to increase. Regulations governing the use of these locomotives soon were formulated and as early as 1920, when a now set of regulations was promulgated, the use of gasoline locomotives in mines could be authorized by the Provincial Inspection Department and no longer depended on obtaining a ministerial decision. Since 1931 this authorization may be given by the Chief Inspector of Mines, Director of the Mining District. Since 1920, safe practices have boon incorporated in the regulations.]

Jan 1, 1940

By Ad. Breyre

Internal-combustion engines have been used in Belgian mines for a long time. As early as 1899, the use of these engines underground was considered, but the general policy was to prohibit such an application unless ministorial permission was granted in special instances. At that time only gasoline engines were available, and a few of these were installed as stationary engines, although in general they wore replaced later by electric or compressed air motors. However, the number of gasoline locomotives continued to increase. Regulations governing; the use of these locomotives seen were formulated and as early as 1920, when a new set of regulations was promulgated, these of gasoline locomotives in mines could be authorized by the Provincial Inspection Department and no longer depended on obtaining a ministerial decision. Since 1931 this authorization may be given by the Chief Inspector of Mines, Director of the Mining District. Since 1920, safe practices have been incorporated in the regulations.

Jan 1, 1940

By Thomas E. McNider, Robert C. Howell, J. W. Stevenson

As of the end of October, 1990, there have been eight spontaneous combustion heatings reported to the Mine Safety and Health Administration (MSHA) at the No. 5 Mine. A reportable heating is defined as one with elevated surface temperatures of the strata greater than ll°C (20°F) above the ambient. The first heatings occurred in November, 1986. The last three heatings were located near the start line of "K" Longwall Panel in the southwest where mining had begun on May 21, 1990. All of the heated areas had been at the time of detection, or were sometime areas of high ventilation pressure differentials or high air velocities. All of the heated areas are in an expanded seam with associated, extensive floor heave which is characteristic of all of the expanded seam thus far exposed by development mining in the No. 5 Mine. Jim Walter Resources, Inc. submitted a plan to MSHA which would reduce the potential for spontaneous combustion at the No. 5 Mine by reducing high air velocities and high pressure differentials in the gob. These two parameters are the dynamics which feed oxygen to the pyrite, thus initiating the oxidation process which can lead to spontaneous combustion. No. 5 Nine operated under this plan for 29 shifts before mining on the longwall was stopped by MSHA and the Spontaneous Combustion Control Plan revoked. This paper briefly details the geology of the expanded seam and history of the heatings. It also gives a retrospective view of the operation under the Spontaneous Combustion Control Plan and reasons why it was revoked by MSHA. Currently, knowledge of the reaction process of the footwall coal seams at No. 5 Mine and other potential spontaneous combustion seams in the United States is limited. There are techniques used in the United States and other countries to minimize the potential for heatings in spontaneous combustion prone areas. The No. 5 Mine has attempted to utilize this current technology. However, in deep, gassy mines the problem is complex.

Jan 1, 1991

By D. T. Van Zandt

IN the late 1920's rotary drills began to replace the churn drills in the petroleum industry, but until the middle 1940's the churn drill was the only widely accepted means of drilling large-diameter blastholes for quarry operations. The Calcite plant of the Michigan Limestone Div., U. S. Steel Corp., was one of the first to experiment with rotary drills for quarry blasthole drilling, and the first to employ compressed air on a fully rotary rig to cool the bit and raise the cuttings to the collar of the blasthole. The Calcite plant operates a limestone quarry near Rogers City, Mich., in the northern part of the lower Michigan peninsula. The formation quarried, a portion of the middle Devonian series, is the Dundee limestone, which is uniform, seldom massive, and characterized by definite bedding planes. The dip is southeast, 40 ft to the mile. Quarry faces vary from 20 to 116 ft in height. Vertical blastholes are used entirely, from three to five rows of holes being drilled parallel to the working face, spaced 18 ft apart with 18-ft burden and drilled 6 to 8 ft below shovel grade. Quarry operations coincide with the navigation season on the Great Lakes, as the bulk of the stone is transported by lake carrier. The normal operating season runs from April to December, the remaining time being devoted to stripping operations and plant and equipment maintenance. In the followirig discussion drilling rates mentioned refer to overall drilling time and include all operations such as moving from hole to hole, penetration and extraction of tools, and routine maintenance. Time consumed by such factors as power delays and major machine repair is not included in drilling time unless otherwise stated. Figures cover only operations at this one plant in the formation mentioned. Needless to say, a very different set of figures could be obtained in a different formation. However, the comparison of footage obtained with churn drills and rotary rigs in this particular formation has been used as an indication of what might be the expected performance of rotary rigs in other formations. Prior to 1950 the bulk of the blasthole drilling at the Calcite plant was done by electrically powered churn drills. Both crawler and wheel-mounted rigs were used. These machines, which mounted a 22-ft drill stem of 4½ in. diam and a spudding type of bit 2 to 4 ft long, drilled a hole of 5 ?-in. diam. Average drilling rate of these rigs in the Rogers City formation was 8 % ft per hr. In 1946 one of the first rotary blasthole drills offered to the quarry industry was put into use on an experimental basis. This machine, known as the Sullivan Model 56 blasthole drill, Fig. 1, was on 16-in. crawler pads and electrically powered at 440 v. The drill bit, a Hughes Tri-Cone roller bit of 5?-in. diam, Type OSC, was threaded into the end of the 4-in. square hollow drill rod or stem. These drill rods were 20 ft long with female threads on one end and male on the other to allow for addition of the desired number of rods for drilling holes of various depth. Rods were handled by a single drum hoist geared to the main drive motor and racked by a 30-ft derrick or mast when not in use. The cable from the hoist drum fed through a crown block on the top of the derrick back to the water swivel mounted in the top end of the drill stem in use. This cable remained attached during drilling operations and was used to hoist the tool string from the hole. Down pressure was applied to the tool string by means of a pair of 4-in. diam hydraulic cylinders acting on the drill chuck holding the drill rod. The first chuck consisted of flat jaws which gripped the flat sides of the stem. These jaws were controlled by set screws forcing them into contact with the drill stem. As these set screws had to be loosened and tightened by hand with each stroke of the hydraulic feed cylinders, there was great delay. For this reason the semi-automatic chuck was developed which automatically gripped the stem on the downward stroke but released for retraction of the hydraulic feed cylinders. Rotation was imparted to the tool string by a rotary table acting on the chuck and geared to the main drive motor through a separate gear train and clutch. A positive displacement water pump, mounted on the drill, fed water through a system of pipes and hose into the water swivel mounted on the top of the drill rod and through the rod and bit, washing the drill cuttings to the collar of the hole. Where water was scarce, provision was made to settle out the cuttings coming from the collar of the hole and re-use the water. Where water was abundant the stream coming from the hole was wasted. Drilling rate with this machine was about 20 ft per hr and bit life 1600 ft of hole. While this rate was more than twice that obtained with the churn drills employed, the problem of water supply and drill cuttings disposal rendered the machine impractical from an operating standpoint. Consequently it was used only in that part of the operation for which water was easily supplied, when the character of the formation made it least difficult to wash cuttings away from the collar of the hole. In October 1949 it was suggested that drill cuttings be removed by compressed air, long used for this purpose on pneumatic drills, and collected at the collar by suction. Thereafter, the water pump on the Sullivan 56 was replaced by a 500-cfm air compressor and a trial run made. Air pressure at

Jan 1, 1955

By M. Copeland

Phase relations of gadolinium alloyed, up to 40 weight-percent (wt pct), with AISI 304-type stainless steel were established. Body-and face-centered cubic iron-rich solid solution phases and several intermetallic gadolinium-containing compounds of variable composition that approximated the formulas Fe9Gd, Ni7Gd2, Ni3Gd, Fe2Gd, NiGd, and NiGd3 were identified. The intermetallic phases Fe9Gd and Ni7Gd2 were noted to melt at about 1,080° C at about 0 to 2 wt pct gadolinium. The melting temperature of Fe9Gd increased with increas-ing gadolinium content to a plateau at about 1,230°C and 30 wt pct gadolinium, and the melting point of Ni7Gd2 decreased to a plateau at 900° C and 30 wt pct gadolinium where Ni3Gd, NiGd, and Fe2Gd coexist. Body-centered cubic iron solid solution was stable from 1 to 2 wt pct gadolinium to higher contents, 30 wt pct gadolinium or possibly more, and face-centered cubic iron up to 12 wt pct gadolinium below 1,200° C. The stability of these phases above 1,200° C was not resolved except for the mel points. A limited number of fabrication variables as well as mechanical and corrosion properties of alloys containing up to 5 wt pct gadolinium were studied. Equilibrating and forming operations were best conducted at about 940° to 1,080° C. Some variability in the yield and tensile strengths of alloys was noted; however, there was a continual decrease in ductility and impact resistance with increasing gadolinium contents. The resistance of gadolinium alloys to corrosion in water at 354° C was about the same as stainless steel.

Jan 1, 1965

By B. C. Peterson

Calumet Division, Calumet & Hecla, Inc., whose operations are in Houghton and Keweenaw Counties, Mich., is a highly integrated and complex organization. This division operates mines, a railroad, a concentrating mill, a reverberatory smelter, and the auxiliary generating plants and shops to service these operations. In addition, it operates a sands reclamation plant, leaching plants, a foundry, and a machine shop that serves varied industries with castings and parts for many applications. Calumet & Hecla, Inc. has produced over 60 percent of all the copper that has been produced in Michigan since discovery of the ore in 1864, and in 1959 the company ranked eight among the country's producers with a production of 17,407 tons. To keep abreast of modern accounting systems developed elsewhere in industry and to combat increasing costs due to higher labor and supply costs, as well as increased costs due to deeper mines and lower grade ore, the company has developed a modern machine cost accounting system. This not only provides the usual bookkeeping and cost accounting facilities but offers accurate cost data for engineering evaluation of the mining operation. This system is credited with being instrumental in permitting continued operation of these high-cost mines in a period of increasing costs with no corresponding increase in the price of metal.

Jan 1, 1962

By Michael A. Knott

Large lateral forces on bridge foundations due to extreme events such as vessel collisions, earthquakes, and wave forces on storm surges during hurricane events are often the controlling design condition for bridge foundations. A review of the American Association of State Highway and Transportation Officials (AASHTO) vessel collision analysis and design codes used in the United States for highway bridges will be presented. The paper includes the background and development of the AASHTO Guide Specification and Commentary for Vessel Collision Design of Highway Bridges (1991) and vessel collision provisions of the AASHTO LRFD Bridge Design Specifications (3rd Edition 2004 and the approved 2005 Interims). Experience in using the AASHTO codes will be discussed and observations on the adequacy and gaps, comparison with the European Standard Code, and recommendations for immediate and long term needs will be presented.

Jan 1, 2013

By Fred N. Kissell

A parachute-type stopping intended for changing the course of mine ventilation air during mine emergencies has been designed and tested. Some production uses are also visualized for metal mines. Preliminary tests in the laboratory and underground indicate that the parachute stopping is a workable concept, but further developmental research is required.

Jan 1, 1975

By A. I. A. Salama, M. W. Mikhail

"A comprehensive software package has been developed at the Western Research Centre to meet many of the coal preparation requirements in the Canadian coal industry. This package performs three main functions: (1) data handling and manipulation; (2) data analysis, including the generation of washability data, performance evaluation and prediction, density and size modelling, evaluation of density and size partition characteristics, and attrition curves; and (3) graphics output.The software described in this paper is potentially a valuable tool for coal preparation plant engineers and operators for evaluating process performance and adjusting plant density separator cutpoints. Moreover, the analytical laboratory technician could find this package very useful in manipulating and presenting laboratory results."

Jan 1, 1997

By Robert J. Henning

The term olivine was first used in 1790 by J. Werner, and the corresponding mineral was so named because of its olive-green color (Hunter, 1941). Olivine is the principal component of the rock known as dunite. While by classic definition dunite is composed of 90% or more olivine, commercial use of these terms has resulted in more specific definitions. Commercially, the term olivine is used to designate a material that consists of 85% or more forsterite and contains 45 to 50% MgO, 39 to 42% SiO2, 5 to 8% Fe2O3, and has an ignition loss (LOI) of 1 to 2%. The term dunite designates a rock that contains 36 to 45% MgO, 36 to 39% SiO2, and has an ignition loss of as much as 10% (Teague, 1983). GEOLOGY Olivine is found in basic igneous and basic metamorphic rocks whose age varies from pre-Ordovician to Tertiary. Economic deposits are of magmatic origin and are restricted to the dunite variety of the peridotite group of ultrabasic igneous rocks. Olivine also occurs in basic igneous rocks such as gabbro, basalt, and diabase and more rarely as an accessory mineral in granite and metamorphosed crystalline limestones. Mineralogy The term olivine refers to a group of orthosilicate minerals in isomorphous series with magnesium-rich forsterite (Mg2Si04) as one end member and iron-rich fayalite (Fe,SiO,) as the other. In most olivines the ratio of magnesium to iron varies from 16: 1 to 2: 1. Commercial olivine deposits contain a mixture of forsterite and fayalite with the fayalite content restricted to less than 15% (Reed, 1959; Teague, 1983). Accessory constituents may include primary minerals such as ilmenite, magnetite, diopside, chromite, and garnet and secondary minerals such as chlorite, serpentine, talc, and vermiculite as alteration products. Chemical and Physical Properties The chemical composition of olivine can be expressed as either (Mg, Fe), SiO, or 2(Mg, Fe)O.SiO,. Table 1 presents chemical analyses for some commercial olivines. The physical properties of olivine are shown in Table 2. Distribution of Major Deposits Commercial olivine and dunite deposits are found in Norway, Japan, Spain, India, Italy, the United States, Sweden, Austria, Pakistan, and Mexico. Noncommercial deposits have been reported in New Zealand, Zimbabwe, South Africa, New Caledonia, Greece, Brazil, and Canada (Teague, 1983). The present markets for olivine are characterized by low unit value, high volume, and high sensitivity to freight costs, so few deposits are commercially viable. Literature from the USSR indicates that considerable research on olivine refractories is being done. (Afansa'ev, 1988), lending credibility to the conjecture that commercial deposits are being mined there. In eastern Canada synthetic olivine is being produced by calcining chrysotile asbestos mine tailings. In the United States numerous lenses of olivine extend in a belt from northeast Georgia northeastward across western North Carolina. Total reserves in North Carolina and Georgia are estimated at between 125 and 200 Mt. The largest US deposit is Twin Sisters Mountain, located in Whatcom and Skagit Counties in the state of Washington. This deposit, which has an outcrop area of 93 km2 and a relief of about 1 525 m. is estimated to contain 1 800 Mt of fresh, unaltered olivine (Teague, 1983). In addition, the US Bureau of Mines reports reserves of 50 Mt on Cypress Island in the state of Washington, and the literature reports eight complexes in southeastern Alaska, some containing cores of olivine as large as 1.6 km in diameter (Taylor, Jr., 1967). The world's largest deposit of olivine occurs in the Aaheim area of Norway, where reserves are estimated at a 2 000 Mt. Several other Norwegian deposits contain as much as 5 Mt each. In Japan the production of ultrabasic rocks is currently about 6 Mtpy, but the bulk of this output is serpentinite. Olivineldunite accounts for only 17% of this production. The major olivine deposit in Japan is located at Horoman Hill on the northern island of Hokkaido. Reserves at this deposit are estimated at 100 Mt (Anon., 1990). Spain is one of the largest producers of dunite. Reserves in the La Coruna District in northwestern Spain are estimated at 100 Mt. India, also a major dunite producer, has a large deposit at Salem in Tamil Nadu. In Italy olivine/dunite is mined from a deposit near Turin. In Sweden the largest deposit is at Arutats and is reported to be comparable in size to the Twin Sisters deposit in the United States. At present the only production in Sweden is from a deposit 30 km south of the town of Gallivare. Reserves at this deposit are reported to be between 1 and 2 Mt. Other significant deposits are: 1) in Austria at St. Stefan near Leoben, 2) in the Swat District of the North West Frontier Province in Pakistan, and 3) in Mexico at Cuidad Victoria in Tamaulipas (Anon., 1990).

Jan 1, 1994

By Guy R. B. Elliott

If chemical mining is to work, it is extremely important to watch heat balances. Some reactions with coal give off heat and others absorb heat. The reactions of coal with oxygen or air give off heat, but the reactions of coal with steam or with carbon dioxide absorb heat. By balancing the proportions of the two types of reactions, the energy of the coal can be almost completely recovered and environmental damage is minimized. The chemical reactions are listed in Table 1 in the usual form with subscripts (s) and (g) indicating solid or gaseous materials. In reaction 1, solid corbon, C(s), reacts with gaseous oxygen, O2(g), to produce gaseous carbon dioxide, CO2 (g). H means enthalpy or available heat in the material; F is free energy, and it measures whether the reaction can go at all, and if so, how much.

Jan 9, 1973

Physical and chemical methods were investigated to tower thorium levels in Eneabba Ilmenite from the natural levels of 180-500 ppm to give Becher Process synthetic rutile with less than 100 ppm thorium. Chemlcal treatments, but not physical separations were successful. A pilot plant trial of a sodium hydroxide leach (25M NaOH at 75°C and 40 wt% solids for Ih) followed by a sulphuric acid leach (3M H2S04 at 90°C and 60 wt% solids for 211) confirmed that thorium could be removed to below 100 ppm. However, the activity of the ilmenite was not lowered to the same extent

Jan 1, 1996

By Christopher Jon Preston, Troy Williams, Daniel Roy

There has been significant progress made with narrow vein gold mines in which a second option for crushing has begun to attract attention. To ensure the profitability of a mine that has based its economics on the absence of a crusher station, more than just best blasting practices are required. Using a blasting operation itself as a primary crusher would undoubtedly save enormous capital costs as well as eliminate some of the costs of crushing ore with the result that considerable savings might be realized. The challenge would be to define the conditions necessary to make this type of operation feasible by providing consistent blasting methods that result in a significant paradigm shift with respect to both blasting and current underground crushing methods. A break model has been developed and applied as a technique in designing blasting patterns based on a unit charge blasting geometry and stress reflection from free faces. There are four components to this model and these are 1) unit charge, 2) thermodynamic/energy, 3) stress reflection, and 4) radial break. Some important changes in timing between holes and rows based on rock properties and the percentage of burden moved were also used. On-site testing at a narrow vein gold mine in Quebec Canada, provided measured parameters for the model. No underground crusher was planned - relying only on the fragmentation profile generated by ring blasting. The specification for muck was that the fragmentation profile needed to be 100% < 400 mm (16 in) with no overbreak - with dilution less

Jan 1, 2019

By Vijaya Thangavelu

Biological leaching of low-grade nickel laterite is based on a non-traditional leaching of oxide minerals using heterotrophic micro-organisms. The organisms solubilise metals by excreting organic acids; these acids then form complexes with heavy metals. High salinity of water supplies and soils in the vicinity of nickel laterite ore bodies is a major abiotic stress to fungi and represents a major challenge in the application of bioleaching process in-situ. Salinity exposes fungi cells to Na+ toxicity and osmotic stress. This study examined the salt tolerance development of Aspergillus foetidus based on gradual acclimatization of organism, its salt threshold and the salinity effect on its metabolism. The biological leaching of weathered saprolite ore with the resulting halotolerant organism under saline conditions was assessed. It was observed that salinity stress affected the organism?s growth and energy utilization

Jan 1, 2006