Search Documents

By A. W. Newberry

The Virginia copper district is situated in North Carolina and Virginia. It contains many mines and prospects that were active at the turn of the nineteenth century. The Bureau of Mines, as part of the strategic-minerals program, began a project in September 1942 to investigate and explore the most promising of the mines in the district. The Seaboard, High Hill, Durgy, and Blue Wing mines were the sites of the main project activity. This report deals principally with these four mines. Drilling did not discover any new ore shoots but indicated the persistence of known ore shoots in depth. There appears to be no indication of impoverishment of copper with depth.

Jan 1, 1948

By J. F. Enrietto

Internal friction measurements were used to determine the effect of manganese on the solubility and precipitation kinetics of nitrogen. Manganese, in concentrations up to 0.75 pct, has little effect on the solubility at temperatures above 250°C. On the other hand, at Concentrations as low as 0.15 pct, manganese inhibits the formation of iron nitrides, especially Fe4N, even though it may not form a precipitnte itself. The precipitation and solubility of carbides and nitrides have been extensively investigated in the pure Fe-C and Fe-N systems.1-3 In recent years, some effort has been ispent in studying the influence of substitutional alloying elements on the behavior of carbon and nitrogen in ferrite.4 -7 In particular Fast, Dijkstra, and Sladek have investigated the effect of 0.5 pct Mn on the internal friction and hardness during the quench aging of Fe-Mn-N alloys.', ' They found that at low temperatures (below 200°C) the presence of 0.5 pct Mn greatly retarded quench aging. For example, after 66 hr at 200°C very little precipitation had taken place in the iron alloyed with manganese, whereas precipitation was complete after a few minutes in a pure Fe-N alloy. The effect of varying the manganese content and the details of the precipitation process were not mentioned in these papers. Fast' postulated that manganese causes a local lowering of the free energy of the lattice with a resulting segregation of nitrogen atoms to these low energy sites. The segregated nitrogen atoms are bound so tightly to the manganese atoms that they cannot form a precipitate. The internal friction measurements of Dijkstra and Sladek tended to confirm the concept of segregation of nitrogen around manganese atoms, and the increase in free energy on transferring a mole of nitrogen atoms from a segregated to a "normal" lattice site was computed to be - 2800 cal. Dijkstra and Sladek9 distinguished between two types of precipitates: ortho, a nitride of appreciably different manganese content than that of the matrix, and para, a nitride with a manganese content essentially that of the matrix. With each type of precipitate a solubility, again designated ortho or para, can be associated. Since the internal friction maximum in alloys which were aged several hours at 600" C dropped almost to zero, Dijkstra and Sladek9 concluded that the ortho solubility must be very low. The effect of temperature on the ortho and para solubilities has no1: been investigated. There are obviously several gaps in our knowledge concerning the influence of manganese on the behavior of nitrogen in a-iron. It was the purpose of the experiments described in this paper to determine the following: 1) The ortho and para solubilities of nitrogen as a function of temperature. 2) The details of the precipitation process at elevated temperatures. 3) The effect of varying the manganese concentration on the above phenomena. EXPERIMENTAL PROCEDURE Internal friction is conveniently employed in studying the precipitation of nitrides and/or carbides from a -iron because it is one of the few parameters, perhaps the only one, which is not affected by the presence of the precipitate itself. For this reason, internal friction techniques were heavily relied upon in the present experiment. A) Preparat of -. All specimens were prepared from electrolytic iron and electrolytic manganese. Alloys containing 0.15, 0.33, 0.65, and 0.75 wt pct Mn were vacuum melted and cast into 25 lb ingots. After being hot rolled to 3/4 in. bars, the ingots were swaged and drawn to 0.030 in. wires. The wires wen? decarburized and denitrided by annealing at 750° C for 17 hr in flowing hydrogen saturated with warer vapor. To obtain a medium grain size, - 0.1 mm, the wires were then heated to 945oC, allowed to soak for 1 hr, furnace cooled to 750°C, and water quenched. Subsequent internal friction measurements showed that this procedure reduced the nitrogen and carbon concentrations of the alloys to less than 0.001 wt pct. The wires were nitrided by sealing them in pyrex capsules containing anhydrous ammonia and annealing them for 24 hr at 580°C, the nitrogen being retained in solid solution by quenching the capsule into water. Immediately after quenching, the wires were stored in liquid nitrogen to prevent any precipitation of nitrides. By varying the pressure of ammonia in the capsule, it was possible to produce any desired nitrogen concentration. B) Internal Friction. The internal Friction measurements were made on a torsional pendulum of the Ke type,'' a frequency OF 1. or 2 cps being used. For

Jan 1, 1962

By Taner Aydogmus

The A$29 billion Chevron-operated Wheatstone Project is one of Australia’s largest resource projects. Located at Ashburton North, 12 kilometers west of Onslow in Western Australia, the project will consist of two Liquefied Natural Gas (LNG) trains with a combined capacity of 8.9 million tons per annum and a domestic gas plant. The LNG Plant will serve the offshore gas fields, which are situated some 250 km off the coast of Onslow in Western Australia. Once operational and on-stream, the Wheatstone Project will contribute to Australia becoming the world’s second largest exporter of LNG. For crossing the environmentally sensitive shore area, a micro-tunnel with an internal diameter of 2 m and approx. 1,242 m in length has been constructed by means of the pipe-jacking method. The micro-tunnel will accommodate a 1.1 m diameter pipeline (trunkline) to deliver gas from the offshore fields LNG Plant. The Wheatstone shore crossing design involves a number of unique challenges owing to its coastal location, where the alignment crosses through a shore area and terminates in a marine environment. This paper provides an overview of the Wheatstone Shore Crossing Project, presents the key features, and discusses the main aspects of the micro-tunneling design.

Jun 13, 2021

By Robert Lee, Jeff Corace, Rob Cyr

Blasting in the heart of the historic Byward Market District of Canada’s capital, Ottawa, presents a unique set of challenges. The obvious difficulties arising on projects requiring blasting within 3 m (10 ft) of 125 year old buildings in various states of disrepair have been encountered and successfully dealt with countless times before. The complexities increase exponentially when tenuous property boundaries, unknown structural details, litigious histories and the need for encroachment agreements lead to individuals with competing interests all able to impact the same operation. Blasting on three projects in the Market was started in early 2005 after months of negotiation. Ultimately, the potential for the projects to proceed hinged on the ability to successfully disseminate blast data to the various stakeholders. As part of the agreements drawn up, property owners demanded immediate notification of the measured vibration levels with contract provisions including clauses such that any exceedance of the USBM criteria immediately triggered project shut down and complete blasting program redesign, and approval by all parties. With stakeholders located in various cities and, in some instances, on various continents, a conventional attended monitoring strategy would not satisfy the requirements. In response to the critical reporting need, Explotech Engineering Ltd. installed unattended monitoring stations around the sites, all incorporating wireless telemetry. After each blast, data was automatically transferred from the monitoring stations to a web-linked server via the wireless network, where it was immediately available to project stakeholders through a password protected website. The solution required a unique blend of data acquisition, telemetry, database, and security technologies, all married to produce a reliable system that was easy to maintain and use. While these types of systems were originally developed for use as permanent monitoring networks in operating mines and quarries, monitoring professionals are increasingly benefiting from the technology on temporary building projects that have typically been the realm of attended monitoring strategies. Globally, this has emerged as a solution to provide more timely access to data for stakeholders, and to minimize the legal exposure from multiple violations of vibration limits. As this trend is likely to continue, the regulated vibration control industry is likely to see a continued shift in technology development to leverage wireless networks and the Internet to continue to improve data transfer, archiving and distribution.

Jan 1, 2006

The greater part of this paper comprises the material used in a lecture delivered to the South Queensland Branch of the Australasian Institute of Mining and Metallurgy in September, 1949. It contains little in the way of original matter, its main purpose being to call attention to the need for research into the properties of Queensland coals and to indicate some of the lines such investigations might profitably follow.Since the lecture was given the Powell Duffryn (1949) 1 report, which has made an excellent start along these lines, has been printed. This report is, however, only a beginning, though a big one, and there is ample room for many years of work along similar lines.The paper is based largely on the work of de Jersey (1946, 1949)2,3,4,5 and Jones and de Jersey (1947)6, but these workers in turn owe a debt to the work of many British and American investigators, too many to enumerate. The subject is a very large one-to deal with it fully would require not a paper but a book; all the author can hope to do is to discuss very briefly some of the main lines of investigation and indicate some of their applications.The reason for selecting Queensland coals in particular is the widespread ignorance of the extent of the coal resources of that State and the almost complete ignorance, to within the last year, of the modern industrial purposes to...

Jan 1, 1950

By D Bruggemann, F Sereshki

There has been an ongoing research on coal and gas outburst for the past two decades at the School of Civil, Mining and Environmental Engineering, University of Wollongong. Research study began with a humble beginning, initially conducting basic laboratory studies on the coal and gas properties, progressing into the determination of gas content of coal by sorption technique and the effect of gas pressures on coal strength. The present laboratory facilities and research interests are extended to include the study of coal permeability and shrinkage properties and their effect of gas drainage characteristics with respect to gas type, and pressures. All the changes are examined with respect to changing in-site geological conditions of the coal deposit investigated. The aim is to provide a long-term support to industry in establishing a data bank for Australian coal deposit characteristics and properties.

Jan 1, 2005

By Thys B. Johnson

The mine system analysis and evaluation study presented in this report was part of the U. S. Bureau of Nines' Tertiary channel project conducted under the Heavy Metals program. The Badger Hill pit, located on the west end of the San Juan Ridge area, near Nevada City, California, was the site of the Bureau's field work. The objectives of this study were: (1) Determine potential alternative mining systems for some of the large tertiary channel gold-bearing gravel deposits, and (2) Identify areas of technology where further investigation would be merited because of their potential inclusion in a mining system for such deposits, The study involved the development of a mineralized block inventory, an economic block inventory, determination of optimum ultimate mining limits and a preliminary economic mining system evaluation. Computer programs were developed and utilized for each of the study phases stated above. The sampling program conducted at Badger Hill by the Bureau Delineation Group together with confidential drill hole data provided by the San Juan Gold Co. formed the basic gold values and distribution information from which a deposit model was developed. The deposit was divided into minable block units and net economic values were assigned to each block for various configurations of both open-pit and underground mining methods based on cost and performance data provided by the various Bureau of Mines Research Centers. A number of controllable variables such as: (1) Mining method (open-pit and underground), (2) depth of mining cut, (3) production rate and (4) equipment type and capacity were evaluated. The prime measures of effectiveness on which the mining systems where judged were discounted cash flow rate of return and maximum utilization of natural resources. The analysis showed that underground mining of the Six-Mile Tertiary channel gold-bearing gravel deposit under consideration was uneconomical and did not permit maximum recovery of the resources within the channel. It was also apparent that mining the Six-Mile Deposit for gold alone is uneconomical or at best marginal at a gold price less than $80 per ounce. The analysis showed that the potential for an economic mining operation within the Six-Mile Deposit exists when the gravel resources of the channel are considered together with the gold. It was determined that the highest rate of return would be realized with a 20-year open-pit mining operation yielding 745,000 ounces of -gold and 55 million cubic yards of usable gravel.

Jan 1, 2012

By N. Hadebe, A. Mampuru, F. Jantjies

Mintek conducted test work to study the effect of media wear when using Mintek’s Milling-in-raffinate technology. The grinding media consisted of high-chrome and ceramic balls. The tests were conducted using a laboratory 5L 316 stainless-steel rubber-lined mill. Magotteaux supplied the high-chrome and ceramic balls. The raffinate was synthetically prepared using a typical Cu/Co (2.2 g/L Cu, 3 g/L Co) composition. The milling rate, media wear, mill, leach extraction efficiencies, gangue acid consumption, and residence time were studied. The tests indicated that the high-chrome balls had a higher corrosion rate than the ceramic balls. The ceramic corrosion rate was lower than 0.1 mm/y. The highchrome balls performed better during the leach stages with faster milling time, higher leaching efficiencies for both Cu and Co, lower gangue-acid consumption, and lower residence time

Jan 1, 2023

By Lex B. Golden

The purpose of this investigation was to evaluate the corrosion properties of certain alloys of titanium and to compare them with those of unalloyed titanium. Such information should make it possible to determine the desirability of substituting these alloys for commercially pure titanium in certain applications. Titanium-manganese, titanium-chromium-iron, and titanium-vanadium-iron alloys, with 2 types of unalloyed titanium, I consolidated by arc melting and the other by powder-metallurgy techniques, were included in the study. Tests were carried out in sulfuric, hydrochloric, phosphoric, nitric, and mixed acids and in chloride solutions. All solutions were saturated with air.

Jan 1, 1957

By Lester A. Blackner

Discussion of the paper of LESTER A. BLACKNER, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 102, June, 1915, pp. 1249 to 1290. SIDNEY J. JENNINGS, New York, N. Y.-In the historical part of the development of the caving system discussed by Mr. Blackner, I notice the absence of one man's name, Charles Henroten. Mr. Henroten used the caving system in South Africa in the. Kimberly mines, and realized from his work there that ground would cave when properly prepared. I think it is due him that his name should be mentioned in connection with an exposition of this system in America.

Jan 12, 1915

By B. Salt, R. Sullivan, E. Roos, M. de Vries, K. McKenna, L. R. Nelson, M. J. N. Uys, P. Jacobs, E. Munnik, P. Lewarne

A review is presented of the furnace cooling system design and operating developments since the initial furnace start up in January 2001 of the Chambishi DC-arc furnace to produce ferrocobalt alloy. The furnace operating conditions present a number of challenges to the furnace designers and operators in particular to provide a sustainable lining that can withstand the highly corrosive siliceous slag (roughly 50% SiO2). This is exacerbated by the dual requirement to operate this slag in a relatively highly superheated state (?T ? 400°C when tapped at 1550°C) to ensure that the ferroalloy can be tapped (estimated 1370°C alloy liquidus temperature) prior to atomisation. The core design challenge occurs at the alloy-slag interface, where a single refractory type cannot simultaneously meet the dual requirement of both adequate alloy and slag corrosion compatibility. Progression by the fourth furnace campaign to involve a retrofit of the bath sidewall to Hatch high-intensity, water-cooled, copper Waffle coolers and tapblocks is described. This involves operation of the entire slag bath, the slag-alloy interface and a portion of the alloy within a more chemically compatible refractory/slag (and possibly at times even an alloy) freeze-lining. Due to the high furnace power density employed (up to 500 kW/m2 hearth area) coupled with the large slag superheat needed, the resulting imposed peak bath sidewall heat fluxes are substantial, especially in the alloy (typically averaging 170 kW/m2), and on occasion have exceeded 1000 kW/m2. The performance of the Hatch Copper Waffle coolers under such aggressive process pyrometallurgical conditions is described. Aspects of the design and especially operating strategies to effect sustained production at up to 38 MW power input are also discussed.

Jan 1, 2004

By A. Whillier

Methods are given for estimating heat flows into mining excavations of various types, with an example to illustrate how the refrigeration requirements are then determined after allowing for the cooling effects of the ventilation air.

Jan 1, 1981

By F. C. Hull

The grain size of a metal or alloy is one of the most important factors determining its properties. In steels, for example, grain size affects hardenability, toughness and machinability; in brasses, grain size is related to hardness and deep-drawing quality. In the field of heat-resistant alloys, grain size has a marked effect on ductility, creep and endurance strength. In order to determine these effects, as well as to control the properties of materials, many accurate and rapid measurements of grain size must be made. This paper presents a new and improved method for the estimation of grain size. Usual Methods OF EvaluatiNg Grain Size A frequetly used method of estimating grain size is that of comparing the image of a polished and etched specimen on the ground-glass screen of a metallographic microscope with standard grain-size charts. Several types of standards are available for use with different classes of microstructures. Geometric Grids.—The Metals Handbook' has a series of hexagonal grids ranging in size from ASTM No. I to 8. Idealized Grain Networks.—Idealized grain.boundary networks for ASTM grain sizes I to 8 are included in the American Society for Testing Materials Tentative Standard E 19 - 39 T, standard Micrographs & Metals Handbook and ASTM Tentative Standard E19-3gT contain micrographs of hypo-eutectoid and hypereutectoid steels ranging in grain size from No. I to 8. The grain size of annealed brass (diameter of the average grain in millimeters) is obtained by comparison with 10 micrographs of varying. grain size in ASTM Tentative Standard E 2-39 T. A handicap to accurate evaluation of grain size by this method is the fact that it is difficult to compare photographs in a dimly lighted room with the image on the ground-glass screen, or, if the general illumination is increased so that the printed standards may be clearly seen, the contrast of the image of the unknown is decreased. It is easier to estimate grain size by comparing a micrograph of the unknown with the grain-size standards. However, photographing every specimen on which the grain size is desired is too costly in time and materials to be practicable. For hardened steels, the Shepherd or Jernkontoret fracture grain-size standards are very accurate and useful, but this method obviously cannot be applied to ductile alloys such as brass, stainless steels and austenitic heat-resistant alloys. Jeffries' method for grain-size measurements consists of counting the number

Jan 1, 1948

By F. C. Hull

The grain size of a metal or alloy is one of the most important factors determining its properties. In steels, for example, grain size affects hardenability, toughness and machinability; in brasses, grain size is related to hardness and deep-drawing quality. In the field of heat-resistant alloys, grain size has a marked effect on ductility, creep and endurance strength. In order to determine these effects, as well as to control the properties of materials, many accurate and rapid measurements of grain size must be made. This paper presents a new and improved method for the estimation of grain size. Usual Methods OF EvaluatiNg Grain Size A frequetly used method of estimating grain size is that of comparing the image of a polished and etched specimen on the ground-glass screen of a metallographic microscope with standard grain-size charts. Several types of standards are available for use with different classes of microstructures. Geometric Grids.—The Metals Handbook' has a series of hexagonal grids ranging in size from ASTM No. I to 8. Idealized Grain Networks.—Idealized grain.boundary networks for ASTM grain sizes I to 8 are included in the American Society for Testing Materials Tentative Standard E 19 - 39 T, standard Micrographs & Metals Handbook and ASTM Tentative Standard E19-3gT contain micrographs of hypo-eutectoid and hypereutectoid steels ranging in grain size from No. I to 8. The grain size of annealed brass (diameter of the average grain in millimeters) is obtained by comparison with 10 micrographs of varying. grain size in ASTM Tentative Standard E 2-39 T. A handicap to accurate evaluation of grain size by this method is the fact that it is difficult to compare photographs in a dimly lighted room with the image on the ground-glass screen, or, if the general illumination is increased so that the printed standards may be clearly seen, the contrast of the image of the unknown is decreased. It is easier to estimate grain size by comparing a micrograph of the unknown with the grain-size standards. However, photographing every specimen on which the grain size is desired is too costly in time and materials to be practicable. For hardened steels, the Shepherd or Jernkontoret fracture grain-size standards are very accurate and useful, but this method obviously cannot be applied to ductile alloys such as brass, stainless steels and austenitic heat-resistant alloys. Jeffries' method for grain-size measurements consists of counting the number

Jan 1, 1948

By Victor Maksaev, Marcos Zentilli

"Abstract - The Domeyko Cordillera, the westernmost uplifted crustal block of the composite High Andes of northern Chile (20°S to 28°S) hosts a narrow N-S trending belt of Late Eocene-Oligocene giant porphyry copper deposits, which include Collahuasi, Chuquicamata, El Abra, La Escondida, and El Salvador. These deposits are spatially and genetically associated with the closing igneous activity along this range, prior to a 30 km eastward jump of the magmatic front in response to tectonic plate interaction. The porphyry copper deposits are also spatially associated with a major intraarc strike-slip shear system, the Domeyko Fault System. Although the tectonic uplift of the 3000 m to 5000 m high range has generally been assumed to be mostly Miocene in age, field relationships suggest that the Domeyko Fault System and tectonic uplift were active as early as the Eocene, coinciding with porphyry copper emplacement between 41 Ma and 30 Ma. Apatite fission track (FT) thermochronology provides both age data and a time-temperature history for rocks since they cooled below a temperature of ca. 125°C (equivalent to a depth of 4 km to 5 km under normal geothermal gradients) on their way to the surface during exhumation, or after a heating event. Apatite FT data from the Paleozoic crystalline basement of the Domeyko Cordillera indicate that at least 4 km to 5 km of rocks were eroded during exhumation of this tectonic block between ca. 50 Ma to 30 Ma (Middle Eocene to Early Oligocene), a time that immediately precedes and overlaps with the emplacement of giant porphyry copper deposits. The FT data constrain the age and duration of a period of crustal thickening and extensive erosion known as the Incaic compression, an event recognized in the Andes of Chile and Peru. Assuming that cooling was due to denudation alone, modelling of the FT data allow estimation of denudation rates between 200 and 100 m/My during this period. In contrast, exposures of pre-porphyry Paleocene intrusives on the western edge of the Domeyko Cordillera reveal apatite FT ages that are concordant with biotite 40Ar-39Ar dates, indicating shallow emplacement, fast cooling and negligible exhumation. The apatite FT ages of the Chuquicamata and El Abra porphyry copper deposits are only marginally younger than their 40Ar-39Ar dates, implying fast cooling/exhumation of shallow mineralizing systems (ca. 2 km to 3 km). Their FT time-temperature history is compatible with extremely low rates of exhumation (ca. 50 m/My) since about 30 Ma (Early Oligocene). This limited extent of erosion, due to exceptional aridity, has greatly contributed to the preservation of rich supergene enriched blankets above some of the porphyry copper deposits.A model is proposed, which is consistent with field relationships, geochemical, and geochronological data. High relative velocities and intermediate-angle oblique convergence between the Nazca and South American plates in the Eocene-Early Oligocene led to intra-arc transpression partitioned into reverse faults of opposing vergence and a right-lateral shear system (the Domeyko Shear System) localized along the magmatic front. Crustal shortening and thickening led to uplift within the Domeyko Fault System and to erosion of at least 4 km to 5 km. Crustal thickening deepened the zone of magma generation, and magmas accumulated in the lower crust, allowing small volumes to rise rapidly to shallow levels along transtensional domains of the regional shear system. A similar model of crustal thickening and shortening before and during porphyry copper emplacement in zones of transtension may also apply to the Miocene-Pliocene giant porphyry copper province of central Chile."

Jan 1, 1999

By Leandro Seixas Bicalho, Wagner Cláudio da Silva, Kelly Laranjeira Nunes, Lívia Marques Faustino

Seeking to implement the Global Industry Standard on Tailings Management to improve the safety of their tailings facilities across the globe, mining companies are motivated to invest in new technologies to recover valuable minerals from tailings. One solution being evaluated is the use of magnetic separators to concentrate ultrafine tailings. However, this approach is energy intensive as it requires high magnetic fields to recover ultrafines, and usually results in low mass yields. Additives that modify pulp rheology and surface properties, or selective flocculate ultrafine particles, were tested to enhance the performance of magnetic separation. Promising results in laboratory scale testing different types of additives confirmed that it is possible to increase the mass yield, keeping the selectivity of this stage.

Feb 1, 2024

By Keith Wallace

Although systematic control of ventilating air currents in underground mines dates back to the Greek and Roman empires, quantified analysis dealing with the cost of providing airflow did not appear until about 1860 when the first fans with acceptable efficiencies became available. Initially, these were introduced to avert methane explosions initiated by shaft bottom furnaces. However, discussions arose on how much coal the steam driven fans consumed in comparison with shaft furnaces in order to produce the sane amount of airflow. Ventilation economics had arrived. In 1981/82 a project was funded by the Department of Energy and carried out at the University of California, Berkeley in order to analyze and compare alternative ventilation designs from the viewpoint of economics and systems efficiency1. This paper highlights some of the results of that study.

Jan 1, 1983

By L. Sandbak

A geomechanical rock mass classification or RMR is currently being used for the evaluation of an LHD mechanized mining system versus the conventional block caving method. The successes and failures of a Panel lS-19 LHD test block on the 2315 level can be attributed to the geologic and geomechanical zonation present. Trench blasting, caving procedures, and sequencing are other factors that were also considered. Lessons learned from the P.lS-19 test block have been used to alter the design for future LHD production blocks on the 2615 level. These modifications are designed to maximize the pillar and insure an adequate draw connection.

Jan 1, 1988

By Walter E. Vanderpool

Full scale load tests are frequently performed immediately prior to deep foundation construction to verify the design assumptions. Occasionally, load tests are performed during design development and applied to the final design for critical and non-redundant structures. We believe that full scale load tests can be very valuable and economical for projects, especially in a geologic environment where the record of full scale load testing is very limited or non-existent. The load testing for the Utah Transit Authority?s Airport Light Rail Trax project provides an example of the advantages of a load test in design development. The savings realized by the owner was in excess of $800 thousand dollars.

Jan 1, 2011

By D. E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2.0 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH's Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis, and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items which require the constant attention of miners operating in these conditions. Disclaimer: Mention of any company or product does not constitute endorsement by the National Institute for Occupational Safety and Health.

Jan 1, 2009