Search Documents

By P. R. Brito-Parada, A. Norori-McCormac

Positron emission particle tracking (PEPT) has become an important tool for flotation research, as it is able to resolve directly the behaviour of particles in laboratory scale flotation vessels. The first applications of PEPT to flotation showed only the motion of an individual particle in the pulp and the froth, but nonetheless allowed interpretations of behaviour not previously possible. Since then, PEPT measurement and data analysis techniques have improved significantly and now ensure a high level of confidence in the particle behaviour obtained. In particular, statistical analysis of long-duration experiments allows time-averaged data to be collated, ensuring spatial accuracy and allowing rigorous comparison of different conditions. It will be shown that these PEPT techniques can be used to compare directly the effect of operating conditions and particle properties in a laboratory flotation system. Particle tracks will be illustrated, as well as analyses of particle speeds, average flow streamlines and occupancy that show marked differences in behaviour near the interface and impeller.

Jan 1, 2015

By E. Miller, J. M. Eldridge, K. L. Komarek

The thermodynamic properties of liquid Mg-Ge alloys have been determined between 1000°and 1500°K by an isopiestic method. Germanium specimens, heated in a temperature gradient and contained in covered graphite crucibles of special geometry, were equilibrated with magrtesium vapor in closed titanium tubes. The crucible design allowed free access of magnesium vapor to the samples during the equilibration to form alloys of magnesium and germanium, but prevented magnesium losses from the crucibles on quenching the titaniuin tubes to terminate the experimental runs, thus preserving the equilibrium alloy compositions. The activities and partial molar enthalpies of magnesium and the integral thermodynamic properties of the system were calculated from the experimental data. THE Mg-Ge phase diagram' shows one congruent melting compound, Mg2Ge, of essentially stoichio-metric composition, two eutectics, and very limited terminal solid solubilities. Very little information is available on the thermodynamic properties of the Mg-Ge system. The free energy of formation of Mg,Ge was recently deter-mined2 by a Knudsen cell technique in the temperature range 610° to 760°C. The standard enthalpy of formation of Mg,Ge was measured calorimetrically by Bever and coworkers.3 The present study was undertaken as part of a general investigation of the thermodynamic properties of the homologous series of Mg-Group IVB systems, i.e., Mg-Pb,4 Mg-Sn,5 Mg-Ge, and Mg-Si. An isopiestic technique was used which was developed by the authors5 for investigating the thermodynamic properties of liquid Mg-Sn alloys. Specimens of the nonvolatile component, contained in covered graphite crucibles, are heated in a temperature gradient in an evacuated and sealed titanium reaction tube, and equilibrated with magnesium vapor of known pressure. The method employs crucibles of special geometry which preserve the high-temperature equilibrium composition of liquid alloys having a highly volatile component such as magnesium on termination of the experimental runs by quenching the crucibles to room temperature. EXPERIMENTAL PROCEDURE First reduction germanium of 99.999+ pct purity (Eagle-Pitcher Co., Cincinnati, Ohio) and 99.99+ pct magnesium metal (Dominion Magnesium Ltd., Toronto, Canada) were used. The graphite crucibles were machined from high-density (1.92 g per cu cm) graphite rods (Basic Carbon Corp., Sanborn, N.Y.) which had a maximum ash content of less than 0.04 pct. The non-reactivity of graphite with germanium at the temperatures used in this study had been previously established by Scace and Sleck.6 The experimental procedure has been previously described in detail.5 The selection of a particular crucible geometry for a run was determined by a combination of imposed experimental conditions, the principle being that more tightly covered crucibles were required to preserve alloy compositions during quenching when higher magnesium pressures and higher specimen temperatures were used. Depending upon the composition range of the equilibrated alloys the source of the magnesium vapor was either pure magnesium or a two-phase mixture of Mg2Ge + Ge-rich liquid of known magnesium pressure. The experimental runs can be divided into the following three groups on the basis of crucible geometry and magnesium source material. Crucibles with Small Holes and Pure Magnesium Reservoirs. The crucible dimensions were identical to those of the Mg-Sn investigation5 except that the hole diameters were reduced to 0.010 in. because of the higher temperatures and higher magnesium pressures involved in the Mg-Ge system. During an equilibration run, magnesium vapor diffused from the reservoir to each specimen through the small holes, one drilled through the crucible lid and two others drilled through graphite baffles positioned vertically inside the crucible between the lid hole and the specimen. Since the magnesium pressure was high, i.e., in the range 117 to 277 Torr, during the equilibration time of approximately 24 hr, equilibration was not impeded by these holes. A specimen composition at equilibrium was fixed by the relative temperatures of the specimen and the reservoir, and by the thermodynamic properties of the system. Upon brine quenching the titanium reaction tube to end a run the vapor pressure of magnesium above the liquid alloys decreased exponentially with decreasing temperature, and the small cross-sectional areas of the holes (4.9 x 10"* sq cm) drastically reduced magnesium losses from the crucibles. Because of its low vapor pressure, germanium losses from crucibles during a run were at most 0.2 mg for pure germanium and correspondingly less for the alloys. This crucible geometry satisfactorily retained the equilibrium alloy compositions on quenching for magnesium-rich (from 3 to 33 at. pct Ge) alloys provided their temperatures were below the melting

Jan 1, 1967

By C. B. Alcock, L. I. Cheng

By the use of radiochemical methods for the study of the gas-liquid equilibria at low temperature, and for the determination of the sulfur contents of metal beads which had been equilibrated with H2S/H2 mixtures of known sulfur potential, it has been possible to obtain the liquid solubility and the free energy of solution of sulfur in liquid tin and lead at temperatures between 500°and 680°C. THE gas-liquid equilibrium method has proved in the past to be most successful in the determination of the thermodynamic behavior of dilute solutions of sulfur in liquid metals.1,2 One of the basic requirements for success with this method is that the volatility of both the metal and its lowest sulfide should be small, otherwise sulfide will be deposited at the cool end of the furnace, where it may react with the outgoing gases to form either sulfur-rich lowest sulfide or higher sulfides. The resultant value of the apparent equilibrium constant will then be lower than the correct one. This argument applies even at sulfur potentials below that in equilibrium with a separate condensed phase of the lowest sulfide at the reaction temperature, T. The mass of sulfide which is deposited at the cold end of the furnace, and hence the extent to which further reaction occurs with the outgoing gases, depends on the time taken for equilibrium to be reached between metal and gas. Since this will depend principally on the bulk of the metal phase which is used, one should clearly attempt to uie as small metal samples as possible. These considerations are important in the study of dilute solutions of sulfur dissolved in liquid tin and lead which both have moderately high vapor pressures as metals and form volatile sulfides. The limit on the size of the metal samples which may be used is set chiefly by the difficulties of analysis for very small amounts of sulfur. The oxygen or carbon dioxide combustion method, followed by iodimetric determination of the sulfur dioxide which is formed,has been found to be successful for the determination of small amounts of sulfur in copper, iron, cobalt and nickel.4 This method was unsatisfactory for sulfur dissolved in tin and lead, mainly because the sulfur dioxide was to some extent absorbed by the copious tin or lead oxide deposits which were formed on the walls of the combustion tube. Furthermore some of the sulfur was found to segregate on the surface of the beads as flaky sulfide crystals which would easily be lost in the transfer of a bead from a boat in the gas equilibration apparatus to one in the combustion apparatus. Oxidation in aqueous media to sulfate ion followed by precipitation as barium sulfate was, therefore, adopted as the analytical procedure. The gas-metal equilibrium experiments were all carried out with radioactive sulfur and thus the analysis involved the counting of barium radiosulfate. Furthermore the use of the radioisotope meant that the approach to the gas-metal equilibrium could be followed continuously by gas counting.' The metal beads were held separately in glass crucibles during equilibration and were transferred from the furnace to the beaker for dissolution in nitric acid still in the crucibles, and thus the possibility of sulfur loss by detachment of the sulfide segregates was eliminated. The temperature range of this investigation was 500° to 680°C. EXPERIMENTAL APPARATUS AND METHOD The apparatus consisted of two furnaces placed in series in a gas recirculation system, Fig. 1. One furnace F1, which was vertical was used to heat the alumina crucible, A, holding six metal beads in separate glass crucibles. The beads weighed between 300 and 700 mg each. The crucible assembly was introduced and removed from the furnace mechanically under a stream of oxygen-free argon. The other furnace, F2, was horizontal and was used to heat a cobalt Co9S8 mixture, held in an alumina boat, and made with radiosulfur containing about 1/2 millicurie per g of sulphur. This mixture, which was finely powdered, was used as a source of known H2S/H2 mixtures6 for a given furnace temperature. The recirculation system also contained a gas re-circulation pump (P), an end window Geiger-Miiller counter (N)—placed downstream of F1 so as to monitor the H2S pressure in the gas leaving this furnace— a sample volume for chemical analysis of the gas phase (G), gas drying tubes (D), filling taps and other standard ancillary equipment. The gas sampling volume was principally used in the cali-

Jan 1, 1962

By M. Krishna, Jayagopal Uchi1, Shanta Sastry, B. M. Satish

"A well-considered composite of ZA-27 reinforced with weight percentage 0, 2, 4, and 6% of alwninite particulate has been made by compocasting technique. The elastic properties of ZA- 27 /alwniniute particulate composite were determined by using U1M. The results showed that the modulus of elasticity and UTS of the composite gradually increases with increase in the wt.% of reinforcement. However, the overall ductility decreased monotonically with an increase in reinforcement. The results of these tests· as well as the predictions of several model~ for composite strengthening available in the literature were compared with experimental results. The data observed from Young's modulus by measurements studies were compared with theoretical results predicted by Eshelby model.IntroductionMetal matrix composites (MMCs) have received increasing attention in _the recent decades as engineering materials. The introduction of a ceramic reinforcement into a metal matrix produces a composite material resulting in an attractive combination of physical and mechanical properties that cannot be obtained with monolithic alloys. Particulate reinf9rced MMCs among the discontinuously reinforced MMCs have attracted quite a lot of attention both in the industrial sectors and the academic communities. There is an increasing need for knowledge about the processing techniques and mechanical behavior of particulate MMCs in view of their production getting enhanced and their commercial applications becoming wider [I]. Interest in particulate reinforced MMCs is mainly due to easy availability of particles and economical processing techniqu"

Jan 1, 2000

By Will H. Coghill, I. L. Feld, G. D. Coe

"INTRODUCTION During the course of research on the beneficiation of the Big Seam iron ores of Birmingham, Ala., an urgent need was felt for quick iron assays of grab samples for mill control. Since the gangue minerals in these ores - quartz, limestone, and clay - all have about the same specific gravity, the use of a specific-gravity method was anticipated as a means of measuring the iron content. The idea of estimating the composition of a mineral mixture by measuring its specific gravity is by no means new. However, the usual method of carry in out this idea proved unreliable when applied to the Big Seam ores. The usual rapid method of determining specific gravity consists of measuring the volume of a known weight of sample that has been dried at high temperature. The inadequacy of this method led to the development of the rapid, modified, specific-gravity determination described in this paper.This work- was an incidental development resulting from research on beneficiation of iron ores by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and ore producing companies of the Birmingham district."

Jan 1, 1946

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and maintenance costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per elm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured underground. The computer outputs for each simulation run are presented in Volume II of this report.

Jan 1, 1983

By Bing Gao, Zhe Wang, Xiangdong Xing, Xueqi Zhang, Shan Ren, Jianliang Zhang

"In sintering, the flame front speed (bed permeability) and sinter qualities are greatly depended on the feed size, especially coke breeze and limestone particle size. It is well known that coke breeze provides sinter bed with heat to meet the demand of partial fusion and diffusion bonding while limestone reacts with iron ore to generate bonding phase in the sintering process. Accordingly, it is necessary to find the optimum combination of different particle size of coke breeze and limestone to yield sinter associated with better qualities. In this study, sinter was produced in the sinter pot with varying coke breeze and limestone particle size together in sintering of a coarse hematite iron ore. The sintering productivity was measured and all of the result sinters were examined by microstructure analysis and reduction degradation test (RDI test). For the sintering of a coarse hematite iron ore, it was found that the optimum mean particle size combination of coke breeze and limestone was 1. 71mm and 1.55mm in the sinter mix. On such a circumstance, sintering productivity was higher and the properties of sinter were better.IntroductionNowadays, as the main iron bearing burden material of modem blast furnaces, sinter has a great influence on the blast furnace operation. Sintering is a greatly complex process involving various chemical reactions to form kinds of mineral phases [1, 2]. In the sintering process, coke breeze is used for fuel and it generates heat to raise the green bed temperature. Limestone serves as flux and it reacts with iron ore to produce various mineral phases. On one hand, during the sintering process, the particle size of coke breeze can have an effect on temperature, atmosphere, the flame front speed and all of them act on the microstructure and mineral constitutions of sinter [3, 4]."

Jan 1, 2013

By G M. Volkmann

Pipe umbrella systems have effectively been used as an additional support system in the working area in weak ground conditions during the last decades. Thus, a considerable number of applications accounts in urban tunnelling with shallow overburden. However, this support system is also successfully used when a tunnel alignment crosses fault zones, sediments, moraines or talus with overburdens from shallow to deep. The pipe umbrella support system itself is termed differently worldwide – synonyms are canopy tube umbrella method, umbrella arch method, or long fore-poling method.One main reason for the increase in application is that this support system closes cost-effectively the gap between reasonable, normal supported tunnels and tunnels supported with more expensive special techniques like horizontal jet-grouting or ground freezing. By using this system, many projects can be built more cost effective without decreasing the common level of safety.The pipe umbrella construction method is pretty young, so the knowledge about this system has been intensely researched in the last decade. This led to an enormous increase in understanding the interaction between support system and surrounding ground, the mode of action, and the important details for construction.Pipe umbrella support systems are applied in difficult ground conditions, so a special developed measurement arrangement was used to observe deformations ahead of the working face during tunnelling. The evaluation of collected data sets identifi ed that cased-drilling systems have clear advantages compared to predrilling systems during the installation process in weak ground conditions. This may become important depending on project requirements, so this difference must be considered in design as well as in the tender document specifications.

Mar 8, 2011

By K Gardner, R Fraval, V Singh

Using new technology to create optimised infill drill programs in underground or open pit settings, it is possible to quantify the value of a drill program. The computer designed programs are optimised to uplift the most amount of resource possible into the specified resource classification, while honouring geological, spatial, equipment and budgetary constraints. When designing ‘by hand’ balancing all these factors is a time-consuming effort with no real way to determine metrics on ‘how good’ a program will be. The optimisation considers many factors allowing geologists to apply critical thinking and domain knowledge to constrain the optimisation, letting the computer do the heavy lifting of determining hole placement. Once programs have been created, they can be integrated into a production schedule. This is a critical step in determining the correct sequencing and balancing of resource availability and seeing how a program will interoperate with other tasks in the mine. For example, if drill drives are a requirement for part of the program, will they be developed in a time frame that is useful for the goals of the program? Do we risk drilling infill holes too late to add value? Do we put production at risk by not classifying parts of the model ahead of time, thus adding to uncertainty? Using software to assist with optimising and scheduling of drilling is a useful technique to save the geologists from the mundanity of manually designing drill programs and puts metrics around the effectiveness of a program and has the potential to add quantifiable value to a program. Examples will be presented that demonstrate the effective use of drill hole optimisation, comparing manual designs with optimised designs, as well as the examples that show the effective use of scheduling.

Mar 22, 2022

By R. Mensah-Biney

The loading characteristics of gold-tetrabromide species onto activated carbon have been evaluated using a completely mixed batch reactor system. The overall loading of gold onto carbon was rapid for the first hour but continued slowly without cessation as a result of reduction of gold. Conventional equilibrium considerations were therefore not applicable. Although loading continued slowly after several days, abnormally high loading capacity values of 10-12 meq/g carbon (650-800 kgAu/tonne) could be attained within 72 hours. The loading of gold-bromo species by activated carbon was by the mass transfer of [AuBr4l-onto the carbon surface where reduction to metallic gold took place. Elution of gold from the loaded carbon was feasible provided the carbon had not been loaded to too high capacity values. If loading is carried to high levels, complete elution becomes impractical and the gold may be recovered by ashing the carbon. For the high loading capacities observed, this option would appear to be cost effective. The effect of several variables on the loading capacity of the activated carbon is discussed.

Jan 1, 1992

By L. C. Bartel

Geologic features such as structure (faults, folds, fractures, etc.), water bearing zones, aquifers, pemeability variations, and porosity variations are important for mine planning and in situ energy recovery processes. Features important for planning a mine will be important for planning the recovery of energy by in situ processes. Various geophysical techniques might be used to obtain the necessary geologic information. In this paper, case histories will be discussed of the use of electromagnetic geophysical surveys at a potential underground coal gasification site and a potential tar sand oil recovery site to obtain pertinent geologic information. Results show that the controlled source audio- frequency magnetotelluric technique shows promise for mapping faults and natural fracture systems when there is a sufficient resistivity contrast.

Jan 1, 1982

By James F. Kemp

The Bulletin of the Institute for March, 1911, is chiefly devoted to papers upon the iron ores of northeastern Cuba. At that time information about the new developments in the peculiar brown hematites of the region was becoming widely circulated and interest was especially keen. For some years exploration had been conducted with pits and trenches and so great an area had been shown to contain ore in the Mayari, Moa, and Cubitas or San Felipe districts, that the reserves conveniently situated for the consumption of American furnaces were estimated as quite two billions of tons. In the subjoined footnote will be found a list of the principal papers of special interest which have already been published.' The further remark may, however, be made that the

Jan 1, 1915

By William J. Almas

Operating uranium mill tailings containment and mill decommissioning activities are regulated by the Nuclear Regulatory Commission (NRC) and the Environmental Protection Agency (EPA) through numerous regulatory mechanisms. Reduction of radon emissions from tailings disposal areas, remedial actions to return groundwater to baseline constituent concentrations, and 200-to 1,000-year stabilization of tailings are major focus areas of regulation. The cumulative economic impact and uncertainty associated with regulation are very significant and will hinder future development of uranium milling facilities.

Jan 1, 1991

By H Zhang, A Lawrence

To accommodate the fast growing need for services in Singapore’s Marina Bay downtown area, Marina South, the construction of a common services tunnel (CST) was required. The CST includes various services such as telecom cables, power lines and water pipes. A deep excavation and temporary earth retaining system (TERS) was required to facilitate the construction of the tunnels. Marina Bay is reclaimed land over thick soft marine clay which is likely to be still consolidating. The deep soft marine clay poses a big challenge for deep excavations in downtown areas where highways and sensitive structures are close by. This paper presents a case study of part of the CST Phase 1B and 2 at Marina South, in particular a 26 m deep excavation supported by a 46 m diameter temporary caisson. The construction started in late 2006 and the basic structure was completed in early 2011. The caisson was formed by 1.0 m thick overlapping diaphragm wall panels with a capping beam and three ring beams at different depths. Two-dimensional finite element analyses were conducted to predict the ground settlement, lateral displacement, bending moment and hoop stresses in the diaphragm wall and ring beams during different excavation stages. A comprehensive instrumentation and monitoring scheme was established to verify the design predictions, control excavation safety and trigger the contingency plan to protect public safety. The impact of construction activity, unbalanced temporary stockpiles and adjacent deep excavation for a mole removal will be discussed.CITATION:Zhang, H and Lawrence, A, 2014. A case history of a deep excavation in a big circular shaft in Singapore marine clay, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 581–588 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Donna lynne Anderson

This report documents the status of a laser-based underground guidance system for tracking and controlling the movements of underground mobile mining equipment. This research is part of a multiple project effort at the U.S. Bureau of Mines to increase mine safety and efficiency by developing technology for computer-assisted mining. Guidance systems, which can track and control the movements of underground mining equipment, are essential during computer-assisted mining operations. A continuous mining machine at the Bureau's surface test facility served as the test-bed for initial development and experimentation of this guidance system. Subsequently, a continuous mining machine in an underground mine served as the platform for in-mine experimentation The first section of this report includes details of the laser sensors, communication network, and computer hardware. The next section includes experimental results, which show the system capable of accurately tracking and controlling the tram maneuvers of a continuous miner underground. The final section discusses conclusions and recommendations.

Jan 1, 1992

By D. A. Shock

Utilizing the technology developed for oil well stimulation by hydrofracing, a disposal system which permanently fixes the waste has been proven. Large quantities of radioactive waste can be processed by a single well system making this method an attractive method for permanent radioactive waste disposal. The system depends on locating a relatively thick formation of impermeable, but easily fracturable rock such as a shale, creating a horizontal fracture, pumping the waste into the fracture in a form which will subsequently solidify and seal the fracture from the well system. The paper presents the theoretical considerations from creating and extending horizontal fractures and how these considerations were used in designing a waste disposal system which is now operating.

Jan 1, 1964

By Defeng Zhou, N. Trubaki, Jian Meng, Fanzhi Menga, Xiaojuan Liu, Yanjie Xia

"The microstructure and the electric conductivity of (Ce0.9Nd0.1)1 xMxO2 d (M=Mo, W) solid solutions were investigated. It has been found that their conductivity containing the grain (s gi ), the grain boundary (s gb) and the total conductivity (s t ) at 300°C- 700°C can be ranked as: (Ce 0. 9Nd 0. 1 ) 0.99 W 0.01 02- d (s gi = 0.065 S.cm·1, (s gb = 0.265 S.cm·1, s t = 0.039 S.cm-1) > (Ce0.9Nd0.1)0.99Mo0.01O2- d (s gi = 0.053 S.cm·1, s gb = 0.142 S.cm·1, s t = 0.029 S.cm-1) > Ce0.9Nd0.1 s 2- d (s gi 0.045 S.cm-1, s gb = 0.091 S.cm-1, s t = 0.018 S.cm-1) measured at 700°C. The highest conductivity is obtained in (Ceo.9Ndo.1)0.99W0.01O2 d. These results indicate that (Ceo.9Nd0.1)0.99W0.01O2- d is the most promising electrolyte materials of intermediate-temperature solid oxide fuel cells among (Ce0.9Nd0.1)1-xMxO2- d. IntroductionRare-earth (e.g. La3+, Nd3+, Gd3+ and Sm3l doped ceria-based ceramic materials have been acknowledged to be attractive electrolytes for solid oxide fuel cells operating below 600°C due to their high ionic conductivity [1, 2]. In order to improve ionic conductivity of these electrolytes further, in recent reports [3-6], some aids such as Mo03 [3] etc. in a limited amount can be used which causes extremely high conductivity. For example, Zhou et al. found that with MoO3 doping, the grain boundary conductivity of Nd3+ doped CeO2- d increased notably especially at lower temperatures due to the effect of severely undersized do pants [3]. It is well known that the size of W6+ (rw6+ = 0.60 Å) is close to Mo6+ (rMo6+ = 0.62A) because of lanthanide shrinkage. Thus, rare-earth doped ceria e.g. Nd3+ doped CeO2g with WO3 in a limited amount will be probably good and even better electrolytes. However, much less information is available about these materials. Therefore, in our paper, (Ce0.9Nd0.1)0.99 1-xMxO2- d (M=Mo, W) solid solutions have been prepared and characterized. Much higher conductive electrolytes are found in the series of (Ce0.9Nd0.1)0.99 M0.01O02- d particularly (Ce0.9Nd0.1)0.99W0.01O2- d"

Jan 1, 2012

By G. C. Hancock

The operating plant of The Broken Hill Associated Smelters Pty. Ltd. is situated at Port Pirie in South Australia and it treats to finality the whole output of lead concentrates from the mines of The Zinc Corporation Ltd., North Broken Hill Ltd., and aroken Hill South Ltd. at Broken Hill, New South Wales. Lead bearing ores from other sources are also purchased for treatment and lead scrap and residues are treated on a toll charge basis. The present output of the plant is approximately 200000 tonnes of refined lead per annum and there is a substantial production of by-products including refined silver, gold, cadmium, antimonial lead alloys, copper matte and sulphuric acid. Recently the Company commenced the production of zinc by slag fuming and electrolysis from a six million ton dump of lead blast furnace slag, which has been accumulating at Port Pirie for over fifty years. The slag fuming plant contains two furnaces of conventional design, but features a high degree of pre-heat for the blast air and this is obtained by the use of all-metal recuperators. The raw zinc oxide fume produced by the plant is roasted in a rotary kiln prior to treatment in the leaching and electrolysis sections, which follow conventional practice for nigh current density plants. Present output is approximately 36000 tonnes of electrolytic zinc per annum.

Jan 1, 1970

By Peter Fischer

Between 45,000 and 50,000 claims for subsidence are submitted each year to the German hard coal industry. In order to improve the service to claimants a quality management was established in 2005. This paper describes the process now used for handling these claims. A quality check has also been carried out by way of a customer survey, which was performed by an independent research agency. The results of the survey are presented in this paper. In Germany, research into mining subsidence mainly involves the prediction of ground movements caused by deep mining operations. Special areas of research are subsidence reducing aspects of the extraction panel planning, especially from the point of view of mining dynamics, as well as securing and restoration measures. This work seeks to prevent or minimize mining-induced damages close to the surface, for instance, buildings or infrastructure installations (such as pipelines), or underground mine openings (e.g. shafts). Roof collapses and surface fractures caused by shallow mine workings of an earlier era currently constitute a special area of investigation.

Jan 1, 2006

By W. U. Reimold, R. Armstrong, R. G. Charlesworth

For many years rockbursts have plagued the mining industry. Although much research has gone into studying this phenomenon only a small proportion of it has been on the actual source mechanism. A study was recently carried out to compliment the previous work done on the micro-structure of these features and to compare it to the micro-structures seen on shatter cones, from meteorite impacts. Both optical and electron-microscopy were used during the study. Samples were collected from rockburst sites by the CSIR Miningtek Rockburst Investigation Unit, and from the collar of the Vredefort Impact Crater. In the optical-microscopy study, the pinnate fractures observed in previous studies were seen in the shatter cones, through all the material. In the rockburst samples, the fractures were observed only in the quartz grains. Quartz micro-crystals were present in the rockburst samples and appeared to be the product of comminution rather than crystallisation. Cataclasite was present on rockburst and shatter cone fracture surfaces. The observations of the shatter cone surfaces with the scanning electron microscope are in agreement with previous work, including the observed presence of melt features, spherules and spheroidal material. The deformation in the rockburst samples is concentrated in the quartz grains, highly complicated with brittle features like sub-conchoidal structures and step structures present. A quartz spherule was identified on one rockburst sample and rhombic-dodecahedra type micro-crystals were present and seen fracturing off quartz grains. It is clear that the rockburst and shatter cone fracture surfaces are quite different; the shatter cone deformation is equally distributed across the sample and involves plastic-deformation, while the deformation in the rockburst material is concentrated in the quartz grains and, with the exception of spherule formation, is brittle. This study agreed with the current explanation for the formation of the rhombic-dodecahedra, and disproved the possibility of it being coesite or fine-grained meta-chert. Although there is no definite evidence of the mechanism of formation of the spherule, it is believed to be the product of vaporization and condensation, and the presence of this material indicates the extreme conditions under which this event occurred.

Jan 1, 2003