Search Documents

By X. G. Zhao, M. Cai, L. K. Ma, P. F. Li

"Crack initiation stress is one of the characteristic stress thresholds in the rock deformation process under compression. By analyzing AE responses of brittle rocks in uniaxial compression, a new method which is called cumulative AE hit (CAEH) method is proposed for determining the crack initiation stress. An advantage of the CAEH method is that the method removes the user's subjective judgment. To verify the CAEH method, uniaxial compression tests with AE measurement using 77 crystalline rock specimens were conducted. The test specimens cover eight rock classes with different mineral grain distributions. Crack initiation stresses of these specimens were determined by the proposed CAEH method and the LSR method, and the resulting mean crack initiation stresses determined using the two methods were comparable. In addition, taking one rock class with 20 specimens for example, the mean crack initiation stresses determined using the CAEH method and those from several established strain-based and AE-based methods were similar. Hence, the CAEH method can be used as an alternative method for crack initiation stress determination.INTRODUCTIONExperimental observations indicate that the failure process of brittle rocks is associated with crack initiation, crack propagation, crack damage and final strain localization (Brace et al., 1966; Bieniawski, 1967; Lockner, 1993; Wawersik & Fairhurst, 1970). Compression tests on cylindrical specimen are often used to characterize the crack development process. The crack initiation stress (sci), crack damage stress (scd), and peak stress (sc) represent important stress thresholds during the failure process of brittle rocks. Among the three characteristic stress magnitudes, sci is difficult to be determined objectively, directly from examining the stress–strain curves. Some researchers argued that sci obtained from laboratory compression tests is an important parameter for estimating the spalling failure observed in brittle rocks around underground excavations (Andersson et al., 2009; Diederichs, 2007; Martin, 1997). sci can also be used to estimate rock tensile strength and Hoek-Brown failure criterion parameter mi (Cai, 2010). Over the last 40 years, various strain-based methods have been proposed to determine the crack initiation stress in compression tests (Brace et al., 1966; Diederichs, 2007; Eberhardt et al., 1998; Lajtai, 1974; Martin & Chandler, 1994; Stacey, 1981). Nicksiar and Martin (2012) proposed a Lateral Strain Response (LSR) method for establishing sci for low-porosity rocks. Meanwhile, they also used different strain-based methods to evaluate sci of Äspö diorite, and the results showed that all strain-based methods gave acceptable crack initiation stress values. Subsequently, they utilized the LSR method to further investigate the crack initiation stresses in igneous, metamorphic, and sedimentary rocks in compression tests (Nicksiar & Martin, 2013). Compared with previously proposed strain-based methods, an advantage of the LSR method is that it removes the user judgment when interpreting sci. However, the use of the LSR method relies on accurate determination of scd and on having a polynomial fitting equation to find the maximum LSR value."

Jan 1, 2015

By Bruno Alves Resende

Em julho de 2010, a linha de Tiras a Quente da Usiminas, planta de Ipatinga, passou a operar com um novo sistema de controle para o laminador de acabamento. Assim, foi necessário atualizar o simulador offline de set up do Trem Acabador, utilizado frequentemente pelas áreas técnica e operacional. Para isso, toda a lógica de cálculo e formulações matemáticas do sistema online foram assimiladas e empregadas no novo simulador. Os resultados das simulações, quando comparados com os valores gerados pelo modelo online, mostraram-se bastante confiáveis. Sendo assim, conclui-se que o aplicativo desenvolvido está apto para ser utilizado como uma ferramenta de simulação offline do modelo de controle do Trem Acabador. Os benefícios potenciais do uso do simulador são: (i) aumento da produtividade por meio da redução de paradas da linha, (ii) melhoria da qualidade final do produto, (iii) redução do número de experimentos na produção e (iv) ajuste dos parâmetros dos modelos de controle. No presente trabalho são apresentadas e discutidas as características do desenvolvimento, da apresentação e da aplicação desse simulador.

Aug 17, 2017

By Luisa Alfieri, Giorgio Fantauzzi, Sergio Notarianni, Spencer Cavagnet, Alessandro Damiani

"The new tunnels of the Copenhagen ""Cityringen"" will be excavated, at Kongens Nytorv square, crossing over the existing M1 and M2 metro lines. After the crossing, the tunnels will underpass the historical building of the Magasin du Nord and adjacent masonry buildings, with a minimum tunnel cover of about 4.5 m. The tunnels have an internal diameter of 4.9m and are being excavated through earth pressure balanced Tunnel Boring Machines in mixed face.The Magasin du Nord estate is characterized by a very complex structure, with different blocks built in different times. An assessment of the condition of the building and its sensitivity to tunnellinginduced ground movements has been conducted through a fully coupled soil-structure interaction analysis; based on the results of this analysis, mitigation measures have been designed.INTRODUCTIONThe Copenhagen Metro Cityringen is expected to be running in July 2019 and will consist of two single tracks in a twin tunnels, each approximately 16 km in length, for transporting up to 243,000 passengers on an average work day. The Cityringen includes 17 underground stations with island platforms, 4 crossover facilities and 3 construction and ventilation shafts. The tunnels is being excavated using earth pressure balanced Tunnel Boring Machines and have an internal diameter of 4.90 m.The intersection with the existing M1 and M2 metro-line will take place at Kongens Nytorv and at Frederiksberg. According to the design alignment, in Kongens Nytorv the new tunnels will pass over the existing M1 and M2 ones; as a result of this, the tunnels will underpass the historical building of the Magasin du Nord and the adjacent masonry building hosting a Mc Donald’s with a minimum cover of about 4.5m.In the framework of Risk Assessment for sensitive buildings, the effects of tunneling-induced ground movements on the Estates ØS0437 (McDonald’s building), ØS0428 (Magasin du Nord) and ØS0004 (Hviids Vinstue) were evaluated. To achieve this goal a fully coupled soil-structure interaction has been considered and the entire excavation process has been reproduced in a 3D model where the abovementioned buildings have been modeled. In this way, a risk assessment analysis was performed evaluating directly the effects of the excavation in terms of settlements and variations of the internal forces as far as the excavation process proceeds. In figure 1, a picture of the construction of Kongens Nytorv station, with Magasin du Nord and Mc Donald’s building on the background, is presented."

Jan 1, 2016

By M. Salimov, J. Sattarvand

The conventional visualisation method of remote equipment is through the installation of one or more cameras on the machine, and sending a live feed to the operator’s flat display. However, the performance of the teleoperation can be enhanced using better visualisation through virtual reality (VR). This paper presents the process of the design and manufacturing of a robotic platform that will be used in the next phase of the project for a VR-assisted teleoperated excavator. The robot consists of a loading boom and arm arrangement installed on the undercarriage of a CAT300-9D. All hydraulic cylinders are replaced with electric actuators, and crawling motors are substituted by electric motors. The pieces of the boom and the arm, as well as the bucket were designed in Autodesk Inventor, and manufactured from aluminium sheets using a desktop and CNC machine. Parts are joined by pins and welding as needed. An Arduino-based control system is developed for the robot, and motor controllers are used to convert the power commands from the microcontroller to the high-amperage actuators. The control system is capable of communicating with a wireless Play Station controller to operate remotely. The manufactured robotic excavator is planned to be utilised in multiple autonomy research projects.

Sep 1, 2021

By Milson de Andrade Júnior

A central termoelétrica número 1 (CTE#1) da Companhia Siderúrgica Nacional possui duas caldeiras em operação denominadas 8 e 9 com capacidade total de produção de vapor de 200 Toneladas por hora. Estas caldeiras fornecem vapor para os turbo geradores e turbo sopradores da CTE#1, além de vapor de processo para a Usina Presidente Vargas (UPV). As caldeiras entraram em operação em 1982/83 e seus sistemas de controle e instrumentação eram totalmente pneumáticos. Ao longo do tempo foi surgindo dificuldades para reposição e manutenção dos componentes pneumáticos, motivo pelo qual se iniciaram os estudos para substituição deste sistema. Em 2009 teve início um projeto para substituição do controle pneumático por um controle microprocessado feito por PLC redundante trabalhando com um supervisório scada e para substituição das malhas de instrumentação pneumática por instrumentação em rede fieldbus. A substituição completa dos componentes pneumáticos foi concluída em 2012. O novo sistema implantado trouxe diversas melhorias na performance, confiabilidade, segurança operacional e ergonomia. Este trabalho apresenta as causas que motivaram o projeto em questão, a metodologia utilizada para a sua implantação e os resultados alcançados com a aplicação de tecnologia moderna para controle e instrumentação de caldeiras.

Jul 31, 2018

By Carlos Vinícius Domingos de Carvalho

As perdas geradas nos processos de uma Aciaria contribuem de forma significativa para a perda metálica do processo. Eventualmente, mesmo com uma operação correta, do ponto de vista de características do produto, pode ocorrer comprometimento do ponto de vista econômico, e uma forma de redução direta dos custos e aumento de performance é a redução das perdas geradas no processo. Desta forma, tornou-se importante realizar um estudo para reduzir as perdas metálicas na Aciaria. Foi utilizado a metodologia Seis Sigma, sendo estratificadas as perdas por processo na Aciaria, onde as maiores perdas na rota dos processos de Lingotamentos Contínuos foram: perda no Distribuidor (24,7%), corte de sequência (17,5 %), retorno de corrida por baixa temperatura do aço na panela (16,3 %); perda por obstrução da válvula da panela (8,8 %). A perda metálica foi reduzida em 50,8%. Além da redução expressiva das perdas, houve uma grande contribuição em relação à compreensão dos modos de falhas para apropriação correta das perdas, tornando as informações mais seguras e facilitando o tratamento de possíveis falhas no processo.

Oct 30, 2017

By Christian Overhagen

In bar and wire rod mills, rolling procedures featuring three- and four-roll technologies are state-of-the-art to produce high-quality long products. While a rolling model for the three-roll process including an equivalent pass method was already presented by the author, pass design methods are dealt with in the current work. The geometry of the rolled product and roll grooves are described mathematically using functional contours, allowing geometric-numerical methods to be used for manipulation and deformation simulation of the rolled product. For a given pass, the output section is constructed using these methods. Roll force, torque and rolling power are calculated using the mathematical rolling model presented before. Interstand tensions are discussed as influencing parameters on the force, torque and power demands, as well as on the section shape. A mathematical model for the influence of interstand tensions on lateral spread is incorporated in the model. To complete the pass design model, elastic mill stand feedback is considered in terms of a fixed elastic modulus for each rolling stand, the elastic feedback and therefore cross-sectional variation due to elastic mill spring being calculated iteratively from the roll force by application of the Gagemeter equation. The interaction of section height and width faults due to elastic mill spring and spread variations is analyzed in detail and the consequences for the roll pass design are shown.

Oct 1, 2019

By Phil Dakin, Rajiv Chandramohan, John Lo Grande, Greg Lane

Crushing and grinding circuit availability is a critical design factor defining the installed equipment selection and the process buffers required to maintain throughput during maintenance. The comminution circuit typically accounts for a process plant’s largest capital expenditure and energy use. Effective process and equipment selection and layout optimization are crucial steps when combining the objectives of cost-effective design and high circuit availability in operation. This paper outlines fit-for-purpose design principles for optimizing process flow, eliminating standby equipment and reducing buffer residence time whilst improving maintainability and operability.

Feb 1, 2025

By Paul Doherty

It is known that the axial capacity of a displacement piles installed in clay varies with time. Consolidation theory suggests that dissipation of porewater pressure set-up during pile installation would lead to increased effective stress and hence higher pile resistance. In recent years a number of case histories have reported time dependent capacity increases for piles installed in sand. Although there is some debate regarding the physical mechanisms controlling this phenomenon, known as ageing, it is unrelated to pore pressure dissipation as piles in sand are installed in primarily drained conditions. A series of field tests designed to investigate ageing effects in soft clay are presented in this paper. Full-scale load tests on 6m long 250 mm square concrete piles, which were driven into soft clay are described. The piles were first tested approximately 100 days after installation, at which stage full equalization of the excess pore pressures had occurred. Static load tests were then performed up to 10 years after pile installation. The piles exhibited significant ageing, with their shaft resistance increasing by up to 66% over a 10 year period. Possible mechanisms for such aging characteristics are explored.

Jan 1, 2011

By C. Zhou, R. Jacksha

This paper reports measurement results for radio frequency (RF) propagation around 90° corners in tunnels and underground mines, for vertically, horizontally and longitudinally polarized signals. Measurements of signal power attenuation from a main entry into a crosscut were performed at four frequencies — 455, 915, 2450 and 5800 MHz — that are common to underground radio communication systems. From the measurement data, signal power loss was determined as a function of signal coupling from the main entry into the crosscut. The resultant power loss data show there are many factors that contribute to power attenuation from a main entry into a crosscut, including frequency, antenna polarization and crosssectional entry dimensions.

Jan 1, 2016

By LUKE O. LINDOE

A major clay products industry in the Medicine Hat area since before 1910 has maintained a continued interest in the clays of the Cypress Hills. For the first forty years the materials used were local red-burning Cretaceous and Pleistocene clays and sands and high-quality stoneware clays of the Whitemud Formation at Eastend, Saskatchewan. Recently a much broader spectrum of raw materials has been brought into use. Including the exposures of the Eagle Butte structure, the Cypress Hills present a 1200 m section of clay-like sediments. Of this 1200 m about 94 per cent, the high montmorillonite shales of the Upper Cretaceous, can be considered useless, or nearly so; the remaining six per cent, all fresh-water beds, presents a wide variety of potentially useful materials. The development of these clay resources is complicated by deep surface creep on the south flank of the Cypress Hills, by largescale slumping on the north flank and by a structural complex in the Eagle Butte area.

Jan 1, 1984

By Eric Jette

IN order to control a chemical process by other than empirical, rule of thumb methods, two types of knowledge concerning the reactions involved must be available: (1) the thermodynamics of the reactions, and (2), by no means less important for efficient operation, the mechanisms and kinetics of the reactions. Information on the thermodynamic side enables the operator to decide upon initial and final conditions, whether heat must be .added or removed from the system, whether the reactions proceed farthest in the desired direction at high pressure or low, etc. Knowledge of the mechanisms involves the determination of the individual steps by which an initial set of reactants, under given conditions, proceed to give the desired final products and kinetic studies upon which the mechanisms are based give the speed at which each of these reactions or steps take place. Thus thermodynamic studies of a 'reaction enable the operator to control the direction and extent to which the reaction can proceed, while kinetic studies enable him to control rates and thus the time' efficiency of the operations. The thermodynamics set the limit to which the reacting system approaches; the kinetics tell how fast the system actually approaches this limit. The two types of information are complementary and not antagonistic even though in discussing the mechanism the introduction of thermodynamics is entirely needless and generally of no assistance, while in thermodynamic studies mechanism need not even be mentioned.

Jan 1, 1931

By A. Gungor

Thermal treatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The assistance of thermal pretreatment prior to grinding by microwave heating is scrutinized in this study. For this purpose three copper ore samples with different chemical composition were used. To see the effect of microwave heating on ore; work index, breakage rate and breakage distribution functions of original and heat treated samples were examined. The results obtained in this study did not show significant improvement in the grindability characteristics of the studied ores with microwave heat treatment. The inadequate amount of microwave transparent matrix was the main reason for the absence of cracks and micro-fractures in the microwave heated copper samples.

Jan 1, 1999

By T. O. Massalski, J. D. Ayers

A massive transformation, 0 —am, takes place in a number of copper-based systems where the ß phase field at high temperatures extends to compositions that are slightly less solute-rich than the limits of the a phase field that exists at lower temperatures. Consequently a solid-state transformation becomes possible that does not involve a change of composition. Within this narrow range of composition the massive am phase can be usually produced in two ways: by a fast quench from the ß phase through the a phase field, or by pulse heating into the a phase field of an undecomposed ß phase retained at room temperature by a prior quench. In the Cu-Ga system the occurrence of a massive am phase has been also observed in alloys whose composition falls outside the equilibrium a phase field1 but not in the Cu-Zn system.2 We have recently observed the occurrence of the ß — am transformation also in two silver-based systems, Ag-Zn and Ag-Cd. The a and 0 phase fields in these systems again slightly "overlap" in a narrow composition range. In the Ag-Zn system this range falls between 36.7 and 40.2 at. pct Zn, and in the Ag-Cd system between approximately 41 and 42.5 at. pct Cd. Alloys were prepared from high-purity materials and cast in quartz tubes under inert atmosphere. No significant change of composition occurred during casting. After homogenizing in the 0 phase field, small pieces of each alloy were reheated at the homogenizing temperatures for a few minutes and quenched into various media. There were examined metallographic-ally after removal of surface layers that may have suffered from contamination or from the loss of the solute element. In the Ag-Zn system extensive areas of the am phase (identified by selective etching, observation of the slip trace variants, and occurrence of twinning) were observed in a comparatively low-zinc alloy (37.8 at. pct Zn) for all quenching media employed: iced

Jan 1, 1969

October 16th, 1872. THE Institute assembled on Wednesday evening at the Western University, and was called to order by President Raymond. Mr. James Park, Jr., of Pittsburgh, made the address of welcome, which was responded to by President Raymond. The Council reported the following names, with approval, for election Ashburner, William, - San Francisco, Cal. Asmus, George, - New York. Baillie, Nathaniel, - Uniontown, Pa. Bowie, A. J., Jr. - San Francisco, Cal. Brown, A. J., - Treasure City, Nev. Butler, J. G., Jr., - Youngstown, Ohio. Chamberlin, J. G., - Leetonia, Ohio. Clark, R. Neilson, - Canyon City, Colorado. Cornell, A. B., - Youngstown, Ohio. De Crano, E. G., - San Francisco, Cal. Engelmann, H., - Salt Lake City, Utah. Faber du Faur, A., - New York. Janin, Louis, Jr., - San Francisco, Cal. Johnson, George J., - Salt Lake City, Utah.. Kent, Joseph C., - Phillipsburgh, N. J. Kent, William St. G., - Phillipsburgh, N. J. Liebenau, Charles von, - Silver City, Idaho. McClintock, A. H., - Wilkes-Barre, Pa. Miller, Thomas N., - Pittsburgh, Pa. Millholland, James A., - Mount Savage, Md. Peters, Ed. D., Jr., - Dudley, Colorado. Reese, Jacob, - Pittsburgh; Pa. Schirmer, J. F. L., - Denver, Colorado. Smith, W. S., - Fairplay, Colorado. Stoelting, Hermann, - Georgetown, Colorado. Sweet, W. A., - Syracuse, N. Y. Tripple, Alexander, - New York. Van Arsdale, W. H., - Swansea, Cal. Willard, Dwight D., - Bordentown, N. J. The following resolution was then offered and passed Resolved, That gentlemen present, not members, be invited to take part in the discussions of the Institute at the various sessions of the present meeting.

Jan 1, 1873

TEE Institute assembled on Wednesday evening at the Western University, and was called to order by President Raymond. Mr. James Park, Jr., of Pittsburgh, made the address of welcome, which was responded to by President Raymond. The Council reported the following names, with approval, for election : Ashburner, William, . . . . . San Francisco, Cal. Asmus, George, . . . . . . New York. Baillie, Nathaniel, . . . . . Uniontown, Pa. Bowie, A. J., Jr., . . . . . San Francisco, Gal. Brown, A. J., . . . . . . Treasure City, Nev. Butler, J. G., Jr., . . . . . Youngstown, Ohio. Chamberlin, J. G., . . . . . Leetonia, Ohio. Clark, R. Neileon, . . . . . Canyon City, Colorado. Cornell, A. B., . , . . . . Youngstown, Ohio. De Crano, E. C., . . . . . San Francisco, Cal. Engelmann, H., . . . . . . Salt Lake City, Utah. Faber du Faur, A., . , . . . New York. Janin, Louie, Jr., . . . . . San Francisco, Cal. Johnson, George J., . . . . . Salt Lake City, Utah., Kent, Joseph C., . . . . . Phillipsburgh, N. J. Kent, William St. G., . . . . Phillipsburgh, N. J. Liebenau, Charles von, . . . . Silver City, Idaho. McClintock, A. H., . . . . . Wilkes-Barre, Pa. Miller, Thomas N., . . . . . Pittsburgh, Pa. Millholland, James A., , . . . Mount Savage, Md. Peters, Ed. D., Jr., . . . . . Dudley, Colorado. Reese, Jacob, . . . . . . Pittsburgh, Pa. Schirmer, J. F. L., . . . . . Denver, Colorado. Smith, W. S., . . . . . . Fairplay, Colorado. Stoelting, Hermann, . . . . . Georgetown, Colorado. Sweet, W. A., . . . . . . Syracuse, N. Y. Tripple, Alexander, . . . . . New York. Van Arsdale, W. H., . . . . . Swansea, Cal. Willard, Dwight D., . . . . . Bordentown, N. J. The following resolution was then offered and passed : Resolved, That gentlemen present, not members, be invited to take part in the discussions of the Institute at the various sessions of the present meeting.

By K L. Temel, W P. Player

The underlying message of this paper is that investment in prospecting, exploration and mining in New Zealand is welcomed. The Government's policy with respect to Crown owned minerals is for continuing investment in prospecting, exploration and mining which is in accordance with good exploration or mining practice. To encourage continued investment requires a business-friendly environment. Government policies and initiatives to enhance the business environment for the minerals and coal exploration and mining industries are discussed in this paper. As well, new initiatives under consideration, which have the purpose of enhancing the investment environment, are discussed.

Jan 1, 1997

By Joseph A. DeCarlo

The annual survey of the oven-coke industry by the Bureau of Mines, United States Department of the Interior, described in this report shows that 79 plants were operating in 22 States December 31, 1956. On that date 15,923 serviceable ovens existed, with a maximum total annual coke capacity of 79,965,100 net tons, and 631 new ovens were under construction. Their annual coke capacity was 3,307,300 net tons. The number of serviceable ovens in existence relates only to those capable of producing coke and does not include (1) any ovens that were blanked off or retired permanently in batteries that were operating December 31, 1956, and (2) ovens that had been demolished and were being rebuilt on that date. For this reason, the number of ovens at furnace plants reported by the Bureau of Mines at the end of each calendar year differs from the number reported for the same group by the American Iron & Steel Institute, as the institute includes ovens being rebuilt.

Jan 1, 1958

By Margaret Armstrong, Arne Berckmans

The longterm aim of this research project is to find fast ways of simulating the recoverable reserves of a deposit for input into financial Monte Carlo simulations without having to conditionally simulate the whole orebody many times. The first step in this re- search is to visualize and quantify the ore tonnage T and the metal quantity Q above an arbitrary cutoff z. This paper presents detailed results for one specific distribution, the lognormal. These lead to a suggestion of a fast way of simulating QTz curves.

Jan 1, 1996

By Marcus Nadler

WAGES in the United States, in spite of the wage freeze, have increased materially. Overtime payments have become standard practice in almost all industries. Now efforts are being made to place wages on an annual basis, and if this is adopted, it will result in an increase in the cost of production. Organized labor today is more powerful than ever before; union membership is large and steadily increasing, and in many instances membership in the union is a prerequisite to employment. The treasuries of many unions are strong as a result of the large membership and full employment. The unions, therefore, today are in a much better position than ever before to carry on long strikes. Politically, too, the unions are more powerful today than they ever were. On the basis of their strength, one may expect that some of the demands that the labor unions will make in the not distant future will be granted. It is, therefore, quite evident that before long, particularly when the curtailment in war production reaches about 40 per cent, this country will be confronted with a serious labor problem.

Jan 1, 1945