Search Documents

By B. Catalano, D. Ifrim

The Annacis Island Outfall Project includes two TBM bored tunnels with face pressures above 3.5 bar, with an internal diameter of 4.2 metres. This paper discusses the innovative approach to TBM tunnelling and TBM design at the Annacis Outfall Project. The TBM custom design includes a 3.6 m OD core machine manufactured by Herrenknecht and a 5.0 m add-on by the Contractor (Bessac), acting as an extension kit, with optimized gantry design to accommodate for short tunnel drives and quicker launches. This novel design approach produced safety improvement, cost and schedule savings while streamlining logistics of TBM retrieval.

Dec 1, 2022

By John H. Gasper

The success of steep slope (>20°) contour mining depends on many factors. Most important is the selection of the mining method that best suits the premining site conditions environmentally and economically. These conditions can be divided into three categories: • Geometric conditions - machine limitations, slope stability restrictions, erosion capacity; • Physical conditions - material properties, rock strengths, ability to dig, driving surfaces; and • Chemical conditions - acid-base relationships, blending or selective placement of overburden. This article incorporates these conditions by conceptually modeling compliance-oriented contour mining methods, particularly haulback methods, using the combined front-end loader (FEL)/ truck, tractor/scraper, and FEL-truck and scraper. Engineering analyses, including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces) and drainage requirements can be performed after the geometric constraints dictated by in situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized, three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple, two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By A. J. Barry

An apparatus and procedure have been developed for testing the anchorage effectiveness of slotted-type bolts. The apparatus consists of: (1) A hydrualic Jack assembly for loading the bolt and (2) a device (extensometer or cathetometer) for measuring displacement of the bolt as it is loaded. This apparatus and procedure permit measurment of anchor slip for loads up to the yield load of the bolt. Two representative makes of slotted-type bolts (a total of 94 bolts) were tested in typical sandstone and shale mine roof. Analysis of the test results showed that (1) anchorage capacities up to the yield load of the bolts can be developed in either rock type; (2) the shape of the slotted end of the bolt affects the ease with which the bolt can be driven; (3) all bolts for which the driving distance was more than 1.25 inches produced satisfactory anchorage in both rock types (thus, driving distance can be used as a criterion for satisfactory anchorage); (4) for the group of bolts that was satisfactorily anchored the anchor slip was unaffected by the type of bolt but was considerably larger in shale than in sandstone; and (5) the bolt expansion, that is, the amount the wedge expands the prongs in excess of the diameter of the hole, can also be employed as a criterion for satisfactory anchorage. Although the bolt-expansion and driving-distance results do not differ appreciably, the latter is recommended because it is easier to determine.

Jan 1, 1954

Mills Day left a journal of his travel to Ohio and return by way of Pittsburgh in 1810. He left this comment about western Pennsylvania: "June 19. As I proceeded toward Pittsburg, (From Washington and Canonsburg) the country grew more populous. The hills appeared to consist of strata of freestone, iron, coal, and slate. June 20. Its (Pittsburg's) water communication with a vast extent of country and the immense beds of coal in its immediate vicinity render it a place peculiarly adapted to manufactures. Coal may be obtained of a good quality, ready delivered at 5 cents a bushel."1 Until within a year or so of this period, coal was used for domestic purposes, brick-making, by blacksmiths, etc.; now the industry entered a period of rapid growth caused by the introduction of the steam engine. As manufacturing was increasing due to the settlement of the western country, the additional facilities created by mechanical power were welcome. Apparently the first engine was installed in Pittsburgh, in a steam grist mill, in 1808; it is described in the Navigator of 1811: "The water of the boilers are heated by large fires made of stone coal, which is introduced at one end into a grated fire place as long as the cylinders themselves; the quantity of coal consumed daily by these boilers is said to be about twenty bushels, which cost one dollar." Later it mentions the effect of burning coal:

Jan 1, 1942

By A. Sinha, C. Sawmliana, P. Pal Roy

Using the newly developed and permitted explosive Pentadyne-HP (Gulf Oil Corporation Ltd., Hyderabad), the Blasting Department of the Central Institute of Mining and Fuel Research, Dhanbad experimented at the GDK-5 Incline, RG-1 Area of the Singareni Collieries Company Ltd. (SCCL) to establish one modified angular cut blasting pattern as an alternative to conventional solid blasting in India to obtain longer pull, as well as to achieve at least 40 t of coal in a single blast round for the deployment of diesel load-haul-dump units at the face. This permitted explosive satisfied the statutory requirements of incendivity characteristics applicable to P5 explosives of the regulatory agency Directorate General of Mines Safety (DGMS) of India. The present paper summarizes the development of this new blasting pattern and its possible use in Indian coal mines.

Jan 1, 2010

By G. E. McElroy

THOUGH air jets occupy only a minor role in the ventilation of mines and other enclosures, their importance in this respect is greater than is commonly recognized and may be considerably increased as our conception of their modes of operation becomes clearer. The object of this paper is to discuss some of the ways in which air jets are involved in mine ventilation and some possible applications to the ventilation of mines and other enclosed spaces. The mention of air jets ordinarily suggests the use of some form of an air injector, such as the Venturi blower occasionally used for auxiliary ventilation in mines, or the Saccardo (injector) system used to a limited extent for ventilating railroad tunnels. Actually, the term covers such common phenomena as the discharge of air from fan pipes and coal-mine line brattices, and even from smoke stacks and fans. A knowledge of the general mode of air entrainment by jets also helps to explain certain phenomena-some mine-gas explosions, for instance-that otherwise would remain obscure. Jet action has been involved in three recent series of Bureau of Mines experiments in which the author has participated: experiments on fan-pipe discharge, on the dilution of gases discharged from a stack and on the ventilation of a ship's hold. Available data on the discharge of jets into large openings and on the design and performance of air injectors have been analyzed in considerable detail and supplementary experiments are planned for after the war. The results of the fan-pipe experiments have been combined with the analyses of data on jet discharge into large spaces, and have been published.1 The results of the stack-gas dilution tests, which refer to a jet discharged into a crosswind, have also been published2 and a paper on the design and performance of injectors has been prepared for publication.3 These technical experiments and analyses form the background and the documented evidence for the following nontechnical discussion of the use of air jets in mine ventilation. JET CHARACTERISTICS The jets commonly encountered are those in which the air is in turbulent-as opposed to laminar, or streamline-motion. The characteristics under discussion apply only to such turbulent jets and have their basis in theories of the mixing of turbulent air currents. Such jets have basic characteristics that are present, though variable in form, regardless of whether the jet expands freely in space, whether the expansion is limited by adjacent walls, or whether the jet propels air through a flow circuit. They expand at definite angles and entrain the surrounding air, even though the entrained air must be obtained by recirculation of their own air streams. As the quantity of air in motion in the mixed stream increases, the average velocity of the stream decreases. In the case of entrainment in the free

Jan 1, 1945

By Hugh S. Spence

IN MAY, 1930, G. LaBine and E. C. St. Paul, prospect¬ing round the southeastern shore of Great Bear Lake, in the North West Territories of Canada, discovered pitchblende at what is now LaBine Point. At the same time, they also found native silver in a small sheared break on an island lying off the point. Late in 1930, samples of the pitchblende were sent to the Mines Branch, at Ottawa. The material consisted of several fair-sized slabs of botryoidal pitchblende banded with a brownish quartz. A small amount of chalcopyrite was visible as small particles and fine veinlets, and the pieces were rather heavily stained a yellowish-green by secondary copper-uranium salts. Analyses were run in the Mines Branch Ore Dressing Laboratories on two samples, and small-scale concentration tests were made on one of them. The results of this work were published in a Memorandum Series report (No. 48) of the Mines Branch, in March, 1931.

Jan 1, 1932

By Robert E. Frey

Regardless of the mechanical design features of a particular air classifier certain basic principles apply. Specifically , there are two forces at work: 1. An air drag force 2. An inertial or centrifugal force. The air drag force has an increasing influence as particles become smaller. A very small low mass particle is easily carried along with an air stream even when turning a corner. Thus, fine particles follow the air away from the classifying zone. Inertial forces increase as the mass of a particle gets larger. Thus oversize particles tend to obey Newton's laws and respond to centrifugal forces or simply continue in a straight path when the airflow changes direction.

Jan 1, 1985

Mark Twain once observed that "Everyone complains about the weather but nobody does anything about it." Not too long ago, the same observation held true for the problem of air pollution. During the past 25 years, however, the mounting concern over air pollution has spurred industrial and governmental research to find ways and means to combat the menacing situation. But for all the time and money spent in recent years to fight it, air pollution is still a major problem in most industrialized communities in America. At the SME Fall Meeting last September, coal's responsibility for such pollution was aired at an informative panel discussion moderated by Ernst Hall. The many-sided problem of air pollution became readily apparent as five experts, representing industry and government, parlayed over the task of cleaning up dirty air. Their opening comments are reprinted here.

Jan 11, 1964

By B. M. Davis

Characterizing exploration prospect potential has aspects that differ from those encountered during ore reserve estimation. One problem is determination of the ore reserve potential prior to acquisition of significant volumes of hard data. The evaluation is subjective and data are usually sparse and of uncertain quality. However, estimations of the ore reserve potential are commonly demanded by management before project funding will be approved. The estimations from several prospects, along with the uncertainties inherent to the estimation, are then used to compare and contrast the potential of several prospects, often with widely varying geologic models.

Jan 1, 1990

By A. P. Paiva

Studies focused on the recovery of precious metals by solvent extraction have recently increased. either to devise suitable solvents or to clarify the involved extraction mechanisms and kinetics. In this work, a comparison of the performance exhibited by triphenylphosphine (TPP), bis-(penty1thio)-ethane (BPTE) and triisobutylphosphine sulfide CI"I'BPS) in the extraction of silver from acidic chloride media is carried out. Extraction and stripping isotherms involving the three extractants are presented together with the results obtained on the selectivity of silver extraction against high contents of iron, copper and lead. Attempts to clarify the mechanism of silver extraction by TIBPS were performed by studying the distribution coefficient dependence on ligand and chloride concentrations. The effect of temperature on extraction and stripping is also considered. The interfacial tension for the system, measured with different concentrations of extractant in the organic phase, is analysed.

Jan 1, 1994

By Andre Zingano, Anderson Weiss

"The objective of this paper is to study the behavior of a low thick and low depth coal seam and the overburden rock mass. The mining method is room and pillar in retreat and partial pillar recovery. The excavation method is conventional drill and blast because of the small production. The partial pillar recovery is about 30% of the previous pillar size, 7m x 7m. The roof displacement was monitored during retreat operation; the surface movement was also monitored. The effect of the blasting vibration on the final pillar strength had been considered. Due to blasting, the pillar reduced about 20%. The consequence is more pillar deformation and roof vertical displacement. The pillar retreat and ground movement were simulated in a three-dimensional numerical model. This model was created to predict the surface subsidence and compare to the subsidence measured. This study showed that the remaining pillar and low seam reduce the subsidence that was predicted with conventional methods.INTRODUCTIONMining low coal seams (less than 1 meter) with the room-and-pillar mining method implies the excavation of part of the roof or floor to maintain adequate entry height for equipment and compliance with labor regulations with respect to ergonomic issues. The direct consequence of this is an increase in coal contamination and the increased cost of transportation and preparation at the plant. Traditional room-and-pillar mining only uses a development operation, even with a continuous miner or drill-and-blasting. Therefore, all the run of mine (ROM) coal is carried out with part of the roof or floor. However, if the retreat mining method were to be considered, the quality of the coal could increase because only the coal seam is excavated from the pillar recovery. The quality of ROM coal will increase, and the cost will decrease proportionally to the amount of coal produced from the retreat operation.However, the retreat mining with partial or total pillar recovery implies greater subsidence. This is particularly true if the coal seam depth is shallow, under 100m depth. Subsidence prediction in room-and-pillar retreat mining is complex; it depends upon the remaining pillar (stump pillar) size, as well as the pillar height, and the behavior of the pillar after retreat. This is related to the strength of the remaining pillar, which is related to the excavated method (drill-and-blast or mechanical)."

Jan 1, 2018

By John Birkinbine

(New Haven 'Meeting, February, 1909.) AWAKENED public interest in efforts to conserve natural resources will certainly be appreciated by the members of the American Institute of Mining Engineers, and a discussion upon conservation may well form a part of one of the Institute meetings, for the records of papers and discussions which appear in the 38 volumes of its Transactions are replete with evidence of effort's in this direction. Every process which reduces the fuel consumed or the power applied per unit of product; every utilization of waste material, or employment of that formerly rejected, to obtain something of value ; every feature of construction or operation which lessens the labor required or increases the output per employee, is an advance in the direction of true conservation. This may not appear from the records of late conferences or from published articles, in which the effort seems to be concentrated upon reducing the consumption and presenting to the people of the country estimates of exhaustion of natural resources. I rejoice in the awakening of public interest in a matter so important for the present and future welfare of our nation; I appreciate the possibility of much good following conferences of the Governors and delegates from various States and from national societies; and I recognize the interdependence, not only of different States, but of contiguous nations. In fact, the marvelous development of transportation by land and by water, and the decreasing rates at which commodities can be moved great distances, have in many cases practically obliterated geographical boundaries, and nearly every country on the globe can either market its product in other lands or draw upon them for raw or manufactured materials ; hence, conservation is an international subject.

Apr 1, 1909

By Bradley V. Johnson, Robert J. Timko, Edward D. Thimons

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has researched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1987

By Christopher P. O?Connor

Stereolithography is a well known rapid prototyping technique in the manufacturing sector. Essentially it is a three dimensional printing process that produces plastic prototype parts from standard CAD files. At present, Canadian mining companies are not fully aware of the potential of Rapid Prototyping Techniques (RPTs) for their production and mine design systems. Mining engineers and geologists attempt to visualize and understand the characteristics and layouts of orebodies on computer models and in cases where it is decided to develop physical models, the process is time consuming based on simplified constructions. Rapid prototyping techniques (RPTs) such as stereolithography can facilitate engineers and geologists to quickly and with satisfactory accuracy to visualize sections of orebodies and evaluate alternative ore extraction techniques using 3D solid models. The research discussed in this paper is carried out by the Laurentian University Mining Automation Laboratory (LUMAL) in collaboration with the Department of Mines Research of Inco Limited and the Integrated Manufacturing Technologies Institute (IMTI) of the National Research Council of Canada. The main objective with this research is to evaluate the applicability of state-of-the-art RPTs (e.g. stereolithography) to underground hard rock mining systems. RPTs can play a significant role in accelerating the design and development process of mining systems.

May 1, 2002

By Olga Frank-Kamenetskaya

The experimental results of study of atmospheric corrosion processes on Saint-Petersburg bronze monuments surface, received in situ and by means of simulating experiments, have been discussed. Influence of the time factor on corrosion film (patina) mineral composition has been analyzed. Direct dependence between patina mineral composition and environmental conditions has been proved. The sequence of patina phases crystallization has been established. Effect of the chemical composition and heterogeneity of artistic bronze and also monument surface structure on the rate of corrosion process has been regarded. The time variations of mass of the crystallized in the hydrochloric acid vapor phases have been investigated. The kinetic laws of their development at the initial stage of formation, indicating simple (non chain) reactions, have been revealed.

Jan 1, 2006

By Malcolm J. McPherson

The highest recorded loss of life due to the collapse of mine workings occurred at the Coalbrook North Colliery in South Africa on 21st January, 1960. A total of 437 persons died when bord and pillar workings collapsed over an area exceeding one square mile The whole mass of strata from the 470 ft (143 m) deep seam to the surface being affected. Although the Coalbrook disaster was unique in its scale the problem of pillar failure, particularly in old workings, is by no means uncommon nor confined to recent history. Indeed, the collapse of large pillared areas was a regular feature of mining in the north of England in the early part of the nineteenth century. When a section of underground workings collapses, the air under the descending roof is compressed very rapidly. The pressurised air is dissipated subsequently at a rate governed by the leakage paths available. If the collapsing area is small, such as the case of a local fall of roof, then there will be little danger of an air blast. If, however, an extensive area collapses suddenly then the rapid compression of air will give rise to a pressure shock wave that will be transmitted through the remaining workings as an air blast. If worked out areas are connected to current workings via unstopped airways an air blast caused by pillar failure in the old workings will be extremely hazardous to personne1 and may cause extensive damage to equipment, perhaps even reaching to surface plant. At Coalbrook, the air blast blew out a wall in the surface fan house. Areas that are considered liable to sudden collapse may be isolated from current workings by the construction of stoppings. However, such stoppings must be capable of withstanding the 'hammerblow' effect of peak air pressures developed during the collapse. The work described in this paper was undertaken in order to determine the maximum air pressures that stoppings must withstand during a major pillar failure. The result has been a method of establishing peak air pressures that is quick and simple to use. Readers who are concerned primarily with the practical application of the method are advised to turn directly to the last main section of the paper.

Jan 1, 1980

By Roe-Hoan Yoon, Kaiwu Huang

Derjaguin and Dukhin [1] were the first to develop a first-principle flotation model by considering the role of surface forces in bubble-particle interactions. According to the model, the ζ-potentials of particles constitute the energy barriers, E12, for particle (1)-bubble (2) interactions, which corroborates well with the observation that flotation recoveries reach maxima under conditions of zero-zeta potentials. In the present work, a series of surface force measurements were conducted for the quartz-dodecylamine hydrochloride (DAH) flotation system, for which detailed studies had been conducted by D.W. Fuerstenau [2], including the measurements of zeta-potentials, contact angles and collector adsorption as a function of pH.

By L. D. Jaffe, H. C. Mann, E. L. Reed

It has been generally believed that fracture originates at a point and, if the stress is suficient, propagates across the material from this point. Evidence to the contrary is given in Fig 1. This micrograph shows an area close to the fracture of a steel containing The material had been quenched from 1675°F and tempered at 1150°F as a round about 10 in, in diam, and had a static tensile strength of 132,000 psi and a static yield strength of 105,000 psi. The steel was broken in 3000 cycles of reversed bending at a nominal max. fiber stress of 110,000 psi at a speed of 10,000 rpm. It was in the form of a standard R.R. Moore specimen with 45" V-notch, 0.015 in. radius and 0.220 in. diam at base of notch. The fractured edge in Fig 1 is part of the central portion of the specimen which broke during the final sudden fracture. Attention is directed to the short cracks which appear as dark lines within the specimen. Similar cracks were found in another specimen of the material, broken in 1,798,000 cycles at a nominal stress of 40,000 psi. The cracks were found in several areas close to the path of the final sudden fracture. This final fracture appeared microscopically to be wholly brittle and transcrystalline. Closer to the surface of the specimens, near the path of progressive fracture, which presumably advanced gradually during many cycles, there was microscopic evidence of some local deformation, but no microcracks. Neither were microcracks observed in areas distant from the main fracture path. The following explanation is offered: In the sudden fracture of the specimen, a crack propagates along a crystallo-graphic plane, with little or no plastic deformation of the adjacent material, until it reaches a grain boundary or a particle of carbide or inclusion which stops its advance. (The particle or boundary may be outside the plane of polish and not visible in the micrograph.) A stress concentration occurs about the end of the stopped crack. One or more new cracks are likely to start in the zone of this stress concentration. They may lie in the same grain as the first crack or in an adjacent grain. New cracks may occasionally start in a nearby but not adjacent grain whose orientation with respect to the stress leads to more ready fracture than does that of the grain between. Once started, these cracks propagate along crystallographic planes in their grains and the process repeats. This leads to discontinuous, branching chains of microcracks. As the process continues, microcracks probably tend to link up by fracture of intermediate material under the influence of increasing stress concentration. Occasionally, too, there may be a series of nearby grains of similar orientation so that there is a certain continuity of fracture across them. In either case the effective size of a crack is increased, resulting in greater stress concentration at its ends and a greater likelihood of further increase of size of the continuously-fractured region. When one continuous crack crosses the entire specimen, macroscopic fracture has occurred. The fractured edge of the specimen in Fig 1 represents a series of microcracks which became continuous across the entire specimen. The short, dark-appearing cracks in the figure did not become continuous over a large area. The row of microscopic stress concentrations at their ends may link up with those of the "main crack" outside the plane of polish. The above explanation does not imply that microcracks develop at the same rate in all portions of the specimen. They will develop most rapidly where the macroscopic tensile stress and macroscopic stress concentration are greatest. Viewed on a scale large compared to the grains, the fracture would appear to progress continuously across the specimen. Although Fig 1 shows a specimen broken in a fatigue test, it is believed that the microcracks discussed do not depend on the repetitive nature of the stressing used, since they are in the region where "sudden" fracture occurred, presumably in a single stress cycle. The whole process of microcrack propagation outlined above is thought to have occurred during this single cycle. It is believed that discontinuous crack propagation may be universal in brittle transgranular fracture of crystalline solids. Further experiments are under way.

Jan 1, 1950

By S. Raghavan

An investigation of the possibility of improving the grinding characteristics of a gabbro ore containing copper and nickel sulfides via a thermal shock treatment technique has been carried out. The results obtained indicate that the breakage characteristics of the gabbro are particles can be significantly improved by preheating the are particles to a temperature around 400°C followed by rapid water quenching. For a given power input and feed size, the thermally treated material produces a product of much finer distribution than the untreated material. An assessment of the improvement in grindability has been made by calculating feed size selection functions for untreated and heat-treated materials.

Jan 1, 1981