Search Documents

By G. H. Harris

The flotation behavior of two high sulfur coals using a non-ionic surfactant as collector from two series of compounds containing oxygenated functional groups was studied in detail using a 2-liter Denver flotation cell. The performance of these reagents was compared with that of an oily collector, namely dodecane. The results showed that at the same coal recovery, a much lower dosage of these non-ionic surfactants was required as compared with that of dodecane. More import was the performance of these compounds as promoters for oxidized as well as un oxidized coal. Mechanisms of interaction of these compounds with the coal are suggested.

Jan 1, 1993

By Drew M. Kurtz, Jeff L. Rai, Sara F. Frailey, Mohammad Ayub Iqbal

"This paper presents the foundation changes made for a five-span bridge over the Lehigh River constructed as a design-build project. During excavation within the cofferdam at Pier 2 for the construction of a spread footing to bear on rock, it proved extremely difficult to control the water entering the excavation as the sheet pile tips were variable due to the bedrock pinnacles and a weathered rock zone above the top of rock allowing water to pass below the sheeting. Water also entered from the bottom of the excavation, possibly due to the presence of solution openings within the dolomite bedrock. After repeated failures to achieve subgrade elevation and maintain a dry excavation, a design change to drilled shafts was made. Additional borings were performed for each of the shaft locations to explore the area underlain by karstic dolomite rock. A seal consisting of tremie concrete with adequate weight was placed to counter the differential head of water and the three drilled shafts (with minimum 25 feet [7.62 meter] rock sockets) were installed. A detailed construction sequence was followed and advanced quality control testing was performed. The construction of Pier 2 was completed successfully.1. INTRODUCTIONThis paper presents the description of the design change made from spread footing to drilled shafts as a result of site conditions encountered during the excavation for the spread footing for a bridge pier in the Lehigh River in Allentown, Pennsylvania. The bridge is located in an area underlain with dolomite rock, presenting karstic conditions including irregular top of rock and solution openings that provided high hydraulic conductivity below the top of rock. Also, the presence of a zone of weathered rock and pinnacle rock prevented the advancement of sheet piles when constructing the cofferdam. Thus, the difficulties of advancing the excavation to the desired spread footing level resulted in the design change to drilled shafts during construction. Since the project was Design-Build, the design could be changed by a collaborative process through the efforts of the Contractor, its geotechnical and structural engineers, and the State's (owner's) geotechnical and structural engineers and construction management staff."

Jan 1, 2016

By Daniel Amponsah-Berko, Palas Kamlakar Borkar, Kwabena Boafo, Neha Sharma, Timothy Eisele

A series of iron-leaching experiments were conducted to test the ability of metal-reducing anaerobic organisms to reduce iron from Fe3+ to Fe2+ to dissolve it from iron ore tailings. This bioleaching process involves the fermentation of biomass from Typha latifolia (a common wetland plant) to generate organic compounds, which, along with metal-reducing organisms, reduce and dissolve iron. The concentration of dissolved iron over time was studied for one year. Iron concentration above 1150 mg/L was achieved at a pH range of 3.95–5.36. Tailings from multiple locations were examined.

Feb 1, 2025

By L O. Filippov, I V. Filippova

Subsea massive sulfide deposits have particular mineralogical compositions and textural features differentiating them from onshore ore. When extracted from salty water and exposed to the air, massive sulfide samples strongly oxidise and soon become covered by thin layers of iron, copper and zinc-rich sulfates and oxides, as well as elemental sulfur. The textural properties vary according to the degree of maturity and the sample position within the hydrothermal deposit. Because of the variation of secondary mineralisation and porosity level, sea floor massive sulfides respond differently from terrestrial ore to processing methods. Froth flotation, commonly applied to separate all types of sulfides from the gangue minerals, is one possible treatment technique to process sea floor ore. Sulfide recovery rate is, in most cases, excellent (>90 per cent). However, separation of the various mineral phases is difficult to obtain even when applying known methods used for onshore ore. Moreover, the flotation behaviour decreases dramatically with time of conservation, even when the samples were stored in a confined environment. High pH range, which is a good way to depress pyrite and therefore to favour the flotation of copper and zinc sulfides, does not have the same effect on subsea ore. Consequently, careful flotation procedure should be elaborated to obtain efficient mineral separation for this specific marine ore.CITATION:Filippov, L O and Filippova, I V, 2015. Processing of subsea massive sulfide ores by flotation – similarity and features with terrestrial ores, in Proceedings Third International Future Mining Conference, pp 239–244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By R. Batterham

"The history of mineral processing is indeed long and has always been tied to mining methods of the day. While many new processes and devices have been developed, the most significant trend in recent times has been the ever increasing scale of operations. There is serious doubt this ongoing trend is enough to match the global trend of falling grades and rising energy demands needed for mineral processing. As well we see that globally, the social licence to operate for mining (and hence mineral processing) is far from secure. Indeed, some argue that mining as we know it is dying and in the future, mining will be much more environmentally secure, even to the extent of insisting upon “in place” recovery and only bringing to the surface the valued product. In this paper we comment on the ramifications of broader uptake of more sustainable mining for mineral processing methods and address the specific question of whether recent progress in in place recovery will lead to a timely breakthrough. The answer proposed is that this is possible in the next 10 - 20 years but in the meantime, the focus is just as likely to be on removal of waste much earlier in circuits. Either way, mineral processing as we know it will change significantly. INTRODUCTION Mineral processing has a long history well covered in a recent publication (Habashi, 2006) who points out “the ancient Egyptians knew already that it would be easier to melt an earth rich in gold particles than another which is poor. As a result, all efforts were made to enrich the gold by washing away the light gangue minerals. Similarly, another ancient method for enriching gold particles from a river stream was by means of fleece, hence the Greek myth of the “golden fleece”. Since the middle ages, striving for improved economics has driven a string of innovative developments in milling and separation. The reader is again referred to the informative and illustrative text by Habashi."

Jan 1, 2018

By C Bonini, A Markham, P Whittle, B Pearson

"Mine-derived sedimentation in rivers can have significant impacts on the processes and features of the receiving environment and impact on communities reliant on this environment. However, identifying and quantifying the contribution of mine-derived sediment to the receiving environment can be complex. This is particularly the case in remote environments and where little/no baseline assessments have been undertaken. One approach that can be used involves sediment fingerprinting, whereby a unique tracer is identified within the mine-derived sediment to discriminate between mine- and non-mine derived sediment sources downstream. The technique typically involves sampling of sediment at upstream, control and impact sites and sites within the mine deposit. Laboratory analyses are run on all the samples to determine whether the chemical signature (eg presence/concentration of specific metals) differs between each group of samples. In complex environments where the mine-derived signature may be difficult to detect from a basic review of the data, or where sampling constraints may limit the number of samples for analyses, statistical methods can be used to help identify sediment groups. This paper provides a mine case study to show how such an assessment can be undertaken despite the logistical challenges faced while working in remote environments.CITATION:Pearson, B, Markham, A, Bonini, C and Whittle, P, 2013. Fingerprinting and signatures - tracing mine impacts in complex aquatic systems, in Proceedings Water in Mining 2013, pp 287-292 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By S. Khan, M. Auret

Due to the modernisation of mines, traditional training methods may be supplemented to support the upskilling of supervisors in mines. A project was initiated by the SAMERDI SATCAP programme to demonstrate the “art of possibility” through a modern training methodology. Two exemplar digital supervisory leadership development modules for underground gold and platinum-group metal conventional and modernising mines, were developed for potential uptake by the mining industry. These exemplar modules were exhibited on a digital platform, towards leading and driving mining modernisation. The research adopted a mixed method approach that included a literature review, a review of an existing supervisory leadership development programme, data gathering, a pilot study, and stakeholder validation workshops. The research supported the development of exemplar digitised modules. The two digitised modules were showcased to the industry for potential adoption. Training slides, a facilitator guide, and a training video were developed for ease of use by industry. The training modules are generic and not specific to a particular mine. They may be used by multi-commodity mines, including gold and platinum-group metals, as ‘stand-alone’ modules. They are customisable, through consultation with relevant service providers for specific working environments. The findings indicated that both the traditional classroom training and the new digitised online learning solution offer advantages for supervisory leadership development. Digital learning is not a new concept for supervisors at mines and modern training methods are well-supported by supervisors in the industry. A ‘modernised’ training solution may consider a ‘blended’ learning approach that combines traditional training with digital methods.

Jun 27, 2025

By Corry Goumans, Dwayne Wallace

"On July 1, 1997, a rockslide occurred on the I-40 in Hayward County, North Carolina that completelyblocked all lanes and disrupted traffic flow in the region. Remedial measures were undertakenimmediately in order to open traffic, however on-going geotechnical investigation revealed stabilityconcerns that necessitated closing the highway to ensure public safety. Access to the top of the slope was available only from the bottom of the slide on the Interstate I-40. Excavation and trim blasting started from the top and along the west slope of the failure, however, additional geotechnical evaluation indicated that slope stability remedial measures were required to support the western rock slope mass."

Jan 1, 1999

By Jan J. Cilliers, Nicolas Barbian, Esther Ventura-Medina

"Froth structure and stability are known to play an important role in determining flotation recovery and selectivity. An industrial sampling campaign was performed to develop a clearer understanding of the effect of flotation variables on froth stability and the role played by the resulting stability on flotation performance.Froth stability was estimated as the fraction of bubbles bursting on the surface of the froth through image analysis and the solids loading on the bubbles at the top surface. It was generally found that high air flowrates resulted in a drop of froth stability showed by a drop in the fraction of air overflowing and a decrease in the solids loading and simultaneously produced low copper recoveries and low concentrate grades. Deep froths only allowed a small fraction of air to overflow and consequently produced low recoveries. An increase from a standard to high frother dosage did not result in a larger fraction of air overflowing, hence producing low recoveries. Likewise, low frother addition only allows low recoveries because the resulting unstable froth cannot support itself. Low aeration was found to be preferential as it allowed high particle loading, therefore high bubble stabilisation, and low gangue entrainment, resulting in the highest flotation performance.Additional laboratory tests were performed to introduce a new stability parameter and to give a clearer understanding of the effect of flotation variables on froth stability. The results confirmed some of the observations made on the plant."

Jan 1, 2003

By R. E. Kennedy

The presence of combustible gases and vapors in air can constitute n extremely serious explosion hazard. This hazard is even greater when explosive mixtures are confined under high pressures, as the pressure can become tremendous immediately before the container is ruptured. Because of its interest in safety in mining and. allied industries, the U. S. Bureau of Mines has investigated the explosive properties of a number of gaseous and liquid compounds; the results of these investigations have been published in various government papers and journal articles. The increased use of liquefied, petroleum gases has intensified interest in the effect of high pressures on the explosibility of propane-air mixtures. The limits of flammability of natural gas-air mixtures have been determined at pressures ranging from 50 min. Hg to 3,000 p.s.i. As it is known that a combustible. gas or vapor cannot burn or explode when the oxygen content of the atmosphere is less than a certain value, critical values were determined for the oxygen content of atmospheres to which nitrogen had been added as a diluent. In this connection limits of flammability were determined for ethane in atmospheres containing added. nitrogen or carbon dioxide at pressures up to 900 p.s.i.g.

Jan 1, 1951

By J. T. Liu

Packing in a flotation column is one way to increase separation efficiency and effective descending flotation-column height. In this paper, the difference between filling packing and sieve packing is described, and the flaws of filling packing in flotation columns in industrial application are pointed out. A change of flotation process and its effect on flotation results are reported. Based on sieve-plate filling, a high-efficiency mixed packing mode consisting of screen-plate packing and honeycomb-tube packing has been proposed, with the packing mode optimized in the cyclonic static microbubble flotation column in the separation zone. In the mixed packing mode, the honeycomb tubes are used to reduce the vortex effect at the base of the column and weaken the radial dispersion of jetting bubbles, and the sieve plates are used to comminute bubbles in the separation zone, to lengthen the bubble migration path, and to stabilize the foam layer. The superiority of honeycomb-tube packing is analyzed using bubble-particle collision theory, and the dynamic equations of collision probability are derived. The role of mixed packing in guaranteeing mineral recovery is analyzed by the axial dispersion method, and a dimensionless axial dispersion model is derived. When a high-turbulence flow is maintained, a static separation environment is formed in which secondary mineral processing is rendered more effective. In this way, a nonlinear separation environment is formed in the flotation column. Finally, mixed packing was applied in an industrial test. A large vortex developed at the base of the column. It was observed that the bubbles in the radial flow were homogeneously dispersed, the residence time of the pulp was prolonged, and the froth layer became thick and stable. Based on the test data, it was found that the sieve packing has the potential to yield a product of approximately 25.83% copper concentration with 91.78% recovery from a feed concentration of approximately 0.727%. If mixed packing were used, the product concentration could be further increased to 27.60% from a feed of approximately 0.739% concentration with 93.38% recovery.

Jan 1, 2014

By D. J. Fray, F. Tailoka

Microporous ceramic tubes (15 micrometre pore diameter) and PVC membranes (10 micrometre diameter) have been used as spargers in the electrowinning of copper from concentrated and dilute chloride electrolytes. At a current density of 600 A/m2 and a nitrogen gas sparging flow rate (at NTP) of 1.53 cm3/s per unit electrode length, it was possible to electrowin planar rather than powdery deposits with copper concentrations as low as 0.157 M. To obtain a planar deposit at higher concentrations of cupric chloride the most realistic optimum current density appears to be between 1 000 and 1 500 A/m2.

Jan 4, 1993

By T. B. Szwilski

ISO 14000 series are voluntary international standards that address environmental management system standards, environmental auditing, environmental labeling, environmental performance evaluation, and life-cycle assessment. An environmental management system (EMS) is a facet of an organization's structure that addresses the immediate and long-term impact of a company's products, services, and processes on the environment. Many companies in the United States are taking a cautious wait-and-see approach before embracing ISO 14000. A few mining companies are reviewing the standards and using them as guidelines. The paper outlines the status, possible benefits to the mining industry, and options available to a company wanting to become involved in the ISO 14000 standards.

Jan 1, 1997

By Don Langlois, Udo Weber

"The effect of grinding media performance on milling and operational behaviour was demonstrated under different selected milling conditions of calcium carbonate. A variety of grinding media material and bead sizes, along with 2 different stirrer tip speeds, were used in the grinding process to generate a particle size reduction of the calcium carbonate (CaCO3). To determine the optimum milling parameters the collected test data was used to calculate and evaluate specific energy as well as stress intensity under different milling conditions.INTRODUCTIONAs a result of increasing energy costs and raw material prices it is important to look at the efficiency of the manufacturing process. Wet grinding and ultrafine wet grinding in stirred media mills are now a possible cost-effective production step for the processing of industrial minerals and precious metals. The generation of smaller particle sizes (down to micrometer scale) can be advantageous for further production steps – i.e. better liberation of precious metals or improved industrial mineral qualities.In the following, the wet grinding process is investigated under different milling conditions of calcium carbonate. Different grinding media materials varying in specific weight, bead size and stirrer tip speeds are used to determine optimal energy consumption for the milling process.DESCRIPTION OF TEST CONDITIONS AND PARAMETERSMill ParametersTests were performed in a Drais Laboratory Perl Mill PML H/V with an installed electrical motor power of 3 kW. The mill chamber is silicon carbide where as the stirrer and discs are made of yttria stabilised zirconia. The mill working volume is 0.9 l. A screen cartridge with a screen size of 0.2 mm is used to separate the beads and slurry at the outlet of the mill. All tests were performed with a grinding media filling grade of 80% (Mill working volume). The stirrer tip speed was set at 6 m/s and 10 m/s."

Jan 1, 2009

By L. F. Terry, H. K. Ihrig, D. J. Sabin, Ralph E. Davis

This paper presents the results of a study of the comparative values of the several fuels commonly used by industrial plants. It shows that the energy actually recovered from any fuel and turned into useful work is dependent upon several factors: (1) the total energy available in the fuel, (2) energy losses resulting from combustion reactions and (3) energy losses dependent upon the mechanics of the firing operation. The chemistry of combustion and the losses resulting therefrom are discussed. The Advantages and disadvantages of the several mechanical methods of firing and the resulting heat losses in each are developed. Data obtained from several typical fuel operations, where careful records have been maintained, are presented to show that the practical results in the actual operation are in harmony with the theoretical results developed in the earlier part of this paper. Water power and solid, liquid or gaseous fuels are at present the only commercial sources of energy. The economic utilization of any one of them depends, in the final analysis, on the cost of energy per unit of finished product to which the energy is applied. The location of the plant utilizing the particular fuel chosen is a large factor in the original choice. The cost per unit at its original natural source, or even in its delivered form, is not always the final measure of its worth. The use of electricity as a source of energy illustrates this to the extreme. Electric current produced from water power is very cheap in certain localities. In Norway, current is sold as low as ½0# per kw-hr., while in dry cells it costs as much as $10 per kw-hr. Yet the sale of dry cells is a large business. The selling price of gas also varies widely. In some localities natural gas for the manufacture of carbon black sells for as low as $0.02 per million British thermal units, while artificial gas for domestic purposes sells for as high as $6 per million B.t.u. Obviously the cost per unit of energy is not the final determining factor in its purchase. Any discussion of the economic utilization of fuels must include costs in relation to the units of finished material manufactured. In large central power generating stations, this is the over-all cost per kilowatt-hour, and in ceramic firing the cost per unit of finished product of a certain quality is the criterion of economic utilization.

Jan 1, 1931

By Cristiano José Scheuer

The effect of low-temperature plasma carburizing treatment on the micro-abrasive wear resistance of AISI 420 steel was investigated by mean of a CSM Calowear ball-cratering equipment. Carburized samples were treated at temperatures of 350, 400, 450 and 500°C for a fixed time of 12 h, using a gas mixture containing 99.5% (80% H2+20% Ar)+0.5% CH4. Micro-scale abrasive wear tests were conducted with a 25.4 mm AISI 420 steel sphere, using an abrasive suspension of alumina (Al2O3) with particle size of 1 ?m (abrasive concentration of 0.11 g/cm³). The contact normal force, abrasive flow and ball rotation speed were fixed at: 0.5 N, 0,2 drop/s, and 120 rpm. The wear craters were analyzed using a confocal laser microscope, Olympus OLS 3000. The wear analyses were performed for test times of: 30, 60, 90, 120, 180, 360, 540, 720 and 900 s (equivalent sliding distance: 0.84, 1.68, 2.52, 3.36, 5.04, 10.09, 15.14, 20.19 and 25.23 m, respectively). The results indicate that the wear coefficient in the outer layer and in the diffusion layer are different, being lower in the latter. It was also verified that the wear coefficient on the outer layer region decreases with increasing treatment temperature in the range of 350 to 450 °C, and increase again for 500ºC. The diffusion layer wear coefficient is similar for all the carburized samples. Finally, for all studied conditions, the analysis of the wear craters surface indicates the occurrence of grooving and micro-rolling abrasion wear modes.

Aug 8, 2018

By Frederic Dewey

(New York Meeting, February, 1913) This old and well-known method of determining, silver is, in bullion work, so far superior to the furnace-assay that it is looked upon with reverential awe by many, if not by most, users, and its-ease of execution, with proper equipment, commends it highly where much commercial bullion work on silver is required. The method is so thoroughly well known that a, description of it here may seem to be unnecessary, but many thousands of determinations are annually made by it in the U. S. Mint Service and its practice is there reduced to an art. This is necessary both for the sake of economy of time, acid because high-grade work with it requires constant practice. It is useless for a person who uses it only occasionally to expect to attain high accuracy with it, without spending more time upon a determination than is warranted in a busy commercial laboratory. It is always employed in the Mint service whenever possible, but its chief field is in the determination of silver in standard silver (ingots and coin), which is 900 fine in silver and 100 fine in copper, and I shall first briefly outline its use on this metal and then take up various points in detail, especially as related to the accuracy of the results obtained.

Jan 4, 1913

By Keith S. McIntosh

The fire assay process for the quantitative recovery of platinum group elements (PGE?s) prior to subsequent analysis traditionally is a time-consuming process. Samples derive from various ore types and contain PGE?s at the ppm or ppb levels, making concentration of the elements mandatory before assaying. Traditionally sample turn-around times are of the order of 24 hours. The whole sequence of sample preparation, fire assay and subsequent analysis of PGE?s have been automated by Anglo Platinum. Some of the major challenges on the road to automation will be discussed and the novel solutions that were implemented. The engineered solution included robotic automation of the whole sequence, from sample preparation, up to the final element by element assay. The final system allowed for rapid (less than one hour) and accurate analysis of PGE?s even in streams containing very low levels, such as flotation tailing streams and drill core samples.

Jan 1, 2006

By W. J. Fene

A comprehensive study of all bituminous coal-mine fatalities occurring in Pennsyl¬ vania during the 5-year period, 1926-1930, was made to try to determine the factors that in¬ fluence accidents which cause these fatalities. During this study some two thousand reports of fatalities were reviewed, and pertinent information as to causes and influencing factors were tabulated therefrom. These tabulations are discussed in detail, and in some instances recommendations are made with a view to reducing the hazards in certain classes of these accidents.

Sep 1, 1931

By Huai-ying Ma, Jun-hua Zhao, Xia Zhao, Si-bin Zhang, Wen Pan, Zhi-xing Zhao

Ignition is the start point of the sintering circuit, which plays an important role during the whole sintering process. The gas consumption accounts for 80% energy cost in the sintering ignition process. Therefore, gas flow reduction is of great significance to energy conservation in the sintering ignition process. In current study, the concept of comprehensive ignition intensity (CII) was introduced to determine the ignition effect. The experimental results indicate that the value of CII increases with higher air-fuel ratio at gas flow of 550 and 600 Nm3/h. From another point of view, given constant CII value, lower gas flow can be achieved with higher air-fuel ratio. Based on the comprehensive ignition intensity, the ignition parameters were optimized and the gas flow was subsequently reduced. By increasing the air-fuel from 5.5 to 6.6, the gas flow is reduced from 450 Nm3/h (8.1 GJ/h) to around 350 Nm3/h (6.3 GJ/h).

Mar 1, 2018