Search Documents

By J. E. Allen

The trend in refractory technology for the copper and nickel industries has been to higher quality raw materials and improved processing technology. These changes have been dictated by the changes in pyrometallurgical processes in these industries. For example the introduction of flash smelting, reaction type smelting and auxiliary slag cleaning furnaces havedemanded better refractories materials. Extensive field applications and improved laboratory testing procedures have helped make this transition possible. Changes in refractory technology, primarily in basic refractories, are followed from the late fifties to the present and into the future.

Jan 1, 1994

By T. M. Nasiatka

This report sterns from a study undertaken by the Federal Bureau of Mines to determine the possibility of reducing filter-cake moisture by applying radiant heat. Suitable laboratory equipment was set up to study the effect of heat, heating time, proximity of the heater to the filter cake, cake thickness, and other variables related to the final filter-cake moisture. A minus-48-mesh coal slurry and application of heat for 60 seconds resulted in filter-cake moistures 5.6 to 13.2 percentage points lower than could be accomplished by filtration alone at 24 inches of Hg for 1-1/4-and 1 1/2-inch cake thickness, respectively. The moisture reduction can be attributed to the combined effect of lower fluid viscosity and evaporation.

Jan 1, 1959

By John R. Green

Rotary kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary accorcling to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. Measurements of Kiln Temperature The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records ox automatic control are desired, while Optica1 pyometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. 1 shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected From puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly 0" to over zoo°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without effect of the flame temperature. There should some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and comments on the possibility of measurement and control. Of greater number and of varied influence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1942

By John R. Green

Rotary kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary accorcling to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. Measurements of Kiln Temperature The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records ox automatic control are desired, while Optica1 pyometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. 1 shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected From puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly 0" to over zoo°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without effect of the flame temperature. There should some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and comments on the possibility of measurement and control. Of greater number and of varied influence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1942

By E. Jackson

This paper describes highlights of the Placer Dome MiniMole project - the development and testing of a robotic machine for mining narrow ore veins. A prototype hydraulically controlled robotic machine was built and tested. The machine provided a platform for testing numerous cutters in the field. Other cutters, e.g. undercutting devices, were tested in the lab. Extensive analyses were done on specific energies and cutter penetration. Three sets of quarry trials were done, then the machine was tested in an underground mine. Rock UCS values varied from 180 MPa to 230 MPa. The paper includes lessons learned and recommendations based on the project findings.

Jan 1, 2007

By Nikolaos Syrtariotis, Mark Berger, Timothy O’Brien, Vojtech Gall

The Northeast Corridor Superconducting Maglev Project (SCMAGLEV) entails construction of a high-speed train system between Washington, DC and New York City, with the first leg between Washington and Baltimore, MD. This innovative project will shorten travel times between Washington DC and Baltimore to approximately 15 minutes, and connect Washington, DC to New York City in under an hour. In 2021 the draft EIS is expected to be issued for comment with a Final EIS/ROD anticipated by early 2022. This paper provides an update on the project as presented in Gall et al. (2020) and discusses the economic and environmental benefits, preferred alignment alternative, preliminary staging and launching of the TBMs for construction, and preliminary station design.

Jun 13, 2021

By J. O. Claassen

"SynopsisMining value chains are dynamic systems and should be managed according to systemic flow-based principles. This includes a detailed focus on the impact of variable geological conditions on material flow, product quality, and production cost, visibility of the total mining system to operators and managers, as well as the synchronization of resources and activities in downstream processes. Thirty mining operations across the African continent were studied to establish to what extent systemic flowbased principles are applied in day-to-day operations. The study indicated that although most mining operations have identified the relevant geoprocessing variables, only a small number apply this information in a flow-based management approach. Most mining operators do not focus on developing a clear flow view of the mining value chain and on making it visible to operators and managers to enable them to optimally set and reset operations. Daily synchronization of geoprocessing variables is limited to a small number of variables, e.g. synchronizing ore hardness with drilling or milling requirements, in less than 30% of the operations evaluated. Operations where these principles have been adopted reported a noteworthy improvement in performance. The study indicates that notable potential exists in most of the operations evaluated to implement flowbased management principles, including geometallurgical principles. This can significantly improve value chain performance without exorbitant capital layouts and enhance ROCE. IntroductionObjective of the studyThe study seeks to establish to what extent systemic flow-based principles have been adopted in the southern African mining industry and the implications thereof. Specific attention is given to the importance of defining and managing geoprocessing dependencies (geological variables directly impacting mining and plant performance – the geometallurgical approach), establishing a flow view of the mining system, which typically includes a dashboard of the flow of ore/product quality and cost from the mining face to the customer, and limiting the impact of dependencies through synchronization of activities and resources, e.g. ensuring that a continuous miner does not wait for a roofbolter, or that reagent addition rates are matched with a specific ore/concentrate composition."

Jan 1, 2015

By Tomás Gonzáles

El presente trabajo describe la metodología usada para evaluar las estrategias de las alternativas del planeamiento a largo plazo en la explotación del mineral y el lixiviable en la Mina Toquepala.

Aug 25, 2002

By B Crompton, A Berghorst, G Knox

Laboratory-based dynamic testing provides an invaluable tool in the development of rock bolts for use in highly stressed, burst prone rock masses. While in most cases the laboratory-based test method is not a direct comparison to an in-situ installation due to the purely axial loading and variations in boundary conditions, it does provide an indication of the performance of the tendon system under dynamic loading. The aim of the research described in this paper is to provide an understanding of the effect of the impact velocity of the impact mass during a laboratory-based dynamic test. Understanding the effect of boundary conditions of laboratory testing will improve Geotechnical Engineers understanding of the performance in an in-situ installation. In addition, due to the limited number of dynamic test facilities, an understanding of the effects of the boundary conditions will aid in the comparison of test results for different products from different test facilities. The research was conducted using an impact tester, whereby a known mass is raised to a known height defining the kinetic energy and velocity of the mass at the point of impact with the test sample after release. The impact velocity was varied between 2.7 m/s and 5.4 m/s, while the kinetic energy of the mass was maintained at 11.5 kJ. While a correlation between the impact velocity and strain rate of the system tested was established, due to the properties of the system tested, the range of impact velocity on which dynamic tests were conducted was insufficient to result in a considerable change in the average impact load, the cumulative proximal displacement and the cumulative maximum energy absorbed over multiple impulse. However, due to the reduction in the momentum of the impact mass the impact duration and displacement during each impulse in the series of impulses reduced. CITATION:Knox, G, Berghorst, A and Crompton, B, 2018. The relationship between the magnitude of impact velocity per impulse and cumulative absorbed energy capacity of a rock bolt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 160–169 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M. T. Ityokumbul

Flotation columns and their variations are increasingly replacing conventional cells in mineral processing circuitry. While the operational characteristics of columns differ from those of conventional cells, the same scale-up methodologies are being employed in design. This practice may be attributed to poor understanding of the factors controlling throughput. The use of tall flotation columns is frequently justified on the requirement for increased particle residence time. It is shown that longer particle residence times in the column cell alone do not translate into increased recoveries. Throughput data from several industrial flotation column installations is presented. An attempt at using dimensional analysis to provide scale-up methodology for the factors controlling column throughput is made.

Jan 1, 1995

By D. Bigby

The current British Standard on rock reinforcement components used in coal mining (BS7861:1996) employs the axial double embedment tensile PET) test to determine the main system load transfer performance criteria, in terms of bond strength and stiffbess. This test involves measurement of load/displacement characteristics of a tendon fully grouted into internally threaded thick-walled steel tubes. Part 1 of the Standard covers rock bolting systems and Part 2 covers birdcaged cable bolting systems. Both parts are highly prescriptive, defining a specific design of bar (AT) and cable bolt (birdcaged). In 2000, it was agreed by the UK Rockbolt Research Liaison Committee that Part 1 of the Standard should be revised to allow further industry innovation of bolts and resins. Amongst other aspects, it was recognised that the double embedment test was limited by its inability to examine load transfer between the bolt and the host rock and the UK Health and Safety Executive commissioned an RMT research project to develop a new test to replace the DET test. The new test, the Laboratory Short Encapsulation Pull (LSEP) test has now been incorporated into a draft revision of BS7861 Part1 which has been issued for industry wide consultation. In 2003, it was agreed to begin revision of Part 2 of the Standard to encompass the many types of long tendon reinforcement which were, by then, being used in the UK coal mining industry. These included flexible bolts, deformed strands and tensionable systems encapsulated with resin, cementitious grout and combinations of the two. A second RMT research project was funded by the HSE to examine adapting the Laboratory Short Encapsulation Pull Test for the revised long tendon Standard. This project is nearing completion and a revised Part 2 of the Standard is being drafted. This paper presents some of the results of the two research projects, describes the laboratory tests and acceptance criteria developed and discusses the implications of the research on improving the understanding of reinforcement performance and its characterisation. In particular it shows how the new test can reveal very different load transfer characteristics to the double embedment test, as it takes the load transfer at the holefrock wall into account.

Jan 1, 2005

By D. Hongjun

In this paper, the flotation rule and behaviors of kyanite-group polymerphous minerals were studied in modified Hallimond tube in detail. Furthermore, the energy change of collector/mineral systems before and after adsorption and the net charge densities of the atoms on the minerals surfaces were calculated by use of quantum chemistry. The flotabilities in minerals were successfully explained.

Jan 1, 1995

By Xie Zhang, Jiang Diao, Xin Qiu, Lu Jiang, Bing Xie, Hong-Yi Li

"Duplex converter process, in which the first converter is used for removing phosphorus from hot metal (De-P), is an important way to produce low P-content and ultra-low P-content steels. In order to improve phosphorization removal and formation of slag with high basicity at relatively low temperature during dephosphorization converter process, effects of temperature, silicon content in hot metal and varied compositions of the De-P converter slag on phosphorus distribution between the slag and hot metal were investigated with thermodynamic calculations and by laboratory scale experiments in present work. Results showed that phosphorus distribution ratio between slag and metal was varied in 10.6~26.6 when basicity of the slag was in the range of 1.5~2.1 at 1370, and the distribution ratio was increased with increasing basicity and Fe10 content in the slag.IntroductionIt is known that phosphorus exists in steel in the form of solid solution, which can significantly improve strength and hardness of steel at room temperature. However, the plasticity and toughness of steel, especially the low temperature plasticity is sharply reduced and leads to high ductile-brittle transition temperature. This phenomenon is commonly known as cold brittleness of steel [1~3]. Hence, phosphorus should be removed as much as possible in the steelmaking process, because it is generally harmful to the iron and steel products."

Jan 1, 2013

By F. K. Spragins

The growing demand and a diminishing supply of conventional crude oil in North America are bringing about an ever increasing interest in the so-called "synthetic fuels". With one commercial plant already in full production, another in the planning and engineering stage, and still others being seriously considered, the Athabasca tar sands is proving to be a leading center of interest. Here, and in the closely related deposits, reserves in place total over 700 billion barrels.1 This major source of new oil is about ready to play a significant role in the filling of ever increasing market demand. When and if fully developed, the Athabasca tat sands could make both Canada and the United States substantially independent of all off-shore supplies of crude for many years to come. Its product, a high-quality, low-sulphur synthetic crude, is beginning to enter the market place at a most favourable time.

Jan 1, 1972

By AIME AIME

T HE 133rd meeting of the A. I. M. E., opening in New York on Feb. 15, promises to be as successful technically and socially as any in the past. The papers submitted for the various technical sessions are unusually excellent and insure something of interest to every group. Tentative programs have already been issued, and a concise resume of the various sessions, arranged chronologically, appears on page 48. Among the many interesting technical sessions arranged, attention is directed to those of the Petroleum Division, embracing the Symposium on Production that has come to be an annual feature, and new ones on refining practice, transportation and economics. The Institute of Metals program is similarly comprehensive. It includes 15 papers, 8 on copper, 4 on aluminum and its alloys, and one each on magnesium, lead, and fatigue of metals. The Coal Committee offers as a leading contribution its report, prepared under the direction of H. N. Eavenson, giving a new analysis of the capacity of the mines and a comparison of coal with other industries. This will be supplemented by a number of other papers of especial interest to operating men, among which are "Data on Use of Loading Machines in Bituminous Mines," by Graham Bright; "Evaluation of Coal," by R. H. Sweetser; "Selection of Coals for the Manufacture of Coke," by H. J. Rose; and "Relation of Origin and State of Carbonization of Coal to Problems of Low Temperature Carbonization," by S. W. Parr. The Iron and Steel Committee has scheduled seven papers, and there will be a special session on open-hearth practice, in which will be presented the first results of the two conferences, held by the sub- committee at Pittsburgh and Cleveland. A symposium on molding sands will be a special feature of the session on non-metallics.

Jan 1, 1926

By Peter Grawenhof

Universal joint shafts and slipper spindles are commonly used in rolling mills to compensate the design- and process-related offset between the motors and work rolls. Although both types of shafts exhibit on the same kinematic principle, there are basic differences regarding the design concepts. These differences become noticeable on many levels and may become very distinct in terms of Life-Cycle-Costs (LCC). In this respect, a critical comparison between universal joint shafts and slipper spindles can be made.

Aug 16, 2017

By Arthur Bell

(San Francisco Meeting, September, 1915) . PRIOR to 1908 the oil production in the State of California, had been almost entirely a heavy fuel, oil, with a high flash point, hut changed within a-short period to a large percentage of refining oil with a low flash, by reason of the coming in of the Santa Maria field, the Midway field, and the increased production of the Fullerton field. This is clearly shown in the following tabulation of California's production: Year Barrels . Below -20° Be, Above 20° Be,, Per Cent_ Per Cent. 1905 48,307,000 90 10 1910 77,698,000 SO 20 1912 90,075,000 6o 31 1914 10:3,600,000 47 53 The bringing in of these high percentage's of light oil with their dangerous low flash and the increasing demand for the refined products necessitated the devising of some cheap and efficient means of quickly separating the lighter elements either in the field or at the main distributing points; also it became necessary to remove the excessive percentage of water which many of the light oils carried in emulsion.

Jan 9, 1915

By Todd W. Armstrong, Michael D. Reader

"INTRODUCTIONThe Playa Vista Development is the largest urban infill development in the history of the United States. Overall, it encompasses about 1100 acres in the City of Los Angeles and is situated north of Los Angeles International Airport near the Pacific Ocean. The development taking place on the project consists primarily of high-density residential condominiums with 1 to 2 levels of subterranean parking . The geotechnical conditions are typified by high groundwater, soft clays, and liquefaction, in addition to environmental issues such as methane.Due to a combination of the geotechnical factors and noise restrictions, both driven and drilled piles were not feasible once the initial phase of the project was occupied. As a result, the project developer undertook a testing program that consisted of the installation and load testing of 9 piles in order to obtain City of Los Angeles acceptance of a pile installation system that met the site constraints. The testing program was divided between two separate contractors operating on sites set on opposite sides on the street (Figure 1 ). Contractors working in Test Areas A & B employed the ""dry dip"" and ""wet dip"" methods of auger pressure grouted displacement (APGD) pile installation, respectively.This paper summarizes the extraordinary program undertaken to install, document, test, and examine auger pressure grouted displacement piles at this site. The program ultimately resulted in City acceptance of auger pressure grouted displacement piles, a historically difficult challenge given the City's resistance of acceptance of ""new"" technologies.A summary of elements included in the test program are: (1) quality control; (2) load testing; (3) long-term testing; (4) non-destructive testing; and (5) pile exhumation."

Jan 1, 2005

By David Lin

"Modal data from Red Dog Main Pit ores were collected and analysed on a size-by-size basis. The Main Pit data were compared to data from composite samples of Red Dog Aqqaluk ores. The data revealed that a large fraction of the sphalerite in the Aqqaluk baritic ore was tied up in sphalerite/galena binaries. This provided an explanation for its poor leadlzinc selectivity compared to Main Pit ores. The Aqqaluk vein ore exhibited levels of sphalerite/galena binaries comparable to that of Main Pit ores resulting in comparable lead/zinc selectivity.An attempt was made to correlate the modal and metallurgical data for Main Pit stockpiles. It was found that there was moderate correlation between the percentage of sphalerite locked in binaries with galena in the <C5>C6 size fi-action and sphalerite deportment to the leadconcentrate.INTRODUCTIONTeck Cominco’s Red Dog Mine in northern Alaska is one of the richest zinc districts in the world. Red Dog Mine has been in operation for over ten years and produces nearly 1 million tonnes of zinc concentrate per mum. Red Dog Mine is an open pit operation and current mining is conducted in the area known as the Main Pit. The Main Pit contains proven reserves of about 41 900 000 tonnes of ore grading 19.2% Zn and 5.2% Pb (Cominco 2000). To the north of the Main Pit is the Aqqaluk deposit. It contains probable reserves of 56 100 000 tonnes of ore grading 16.6% Zn and 4.1 % Pb. After the Main Pit has been exhausted, the Aqqaluk deposit will be exploited.The Aqqaluk deposit consists of three main geologic ore types: baritic, siliceous and vein. The siliceous ore type is dominant, representing 64% of the mineralisation. Composite samples of these ore types were created from drill core and batch flotation tests were performed on them. The flotation tests indicated that there were significant metallurgical differences between Main Pit ore and the Aqqaluk siliceous and baritic ore. The siliceous and baritic ores were found to suffer from poor lead/zinc selectivity (Lin 1999, G&T 1999). It was suspected that there were problems with the original Aqqaluk composite samples, thus a new set of composite samples were created and batch flotation tests were conducted again. In this set of tests, the new baritic ore still suffered from leadlzinc selectivity problems, but the new siliceous ore provided excellent metallurgical results. A summary of the flotation results is given in Table 1. Stockpile 132, which is typical of Main Pit ore, is given for comparison purposes. The mineral suite at Red Dog is relatively simple. The ore consists of galena, sphalerite and pyrite in a silicate matrix. The low zinc recoveries of the baritic ore were largely due to sphalerite losses to the lead concentrate."

Jan 1, 2002

By J. M. Wempen

Booster fans, large underground fans, can increase the volumetric efficiency of ventilation systems by helping to balance the pressure and quantity distribution throughout a mine, reducing leakage and reducing the total power requirement. However, in ventilation systems that use booster fans there is a potential for system recirculation, the leakage of return air to intake air, and also for localized recirculation near the fan through the bulkhead and airlock doors. Air that is recirculated locally decreases the system efficiency because the quantity of air flow through the fan increases without increasing the airflow throughout the system. To understand the detailed flow characteristics of a ventilation system with a booster fan, two-dimensional computational fluid dynamics (CFD) models were developed using the software Ansys-FLUENT. Though two-dimensional models do not represent the full complexity of the flow dynamics, they do provide a good representation of the flow characteristics and they allow for a qualitative analysis of how the flow dynamics are affected by the system characteristics. The CFD models were used to evaluate how the number of booster fans, the booster fan placement, the location and geometry of the fan installation and the construction of the airlock system affect the flow characteristics and the localized efficiency of the ventilation system.

Feb 27, 2013