Search Documents

By L. D. Keller

The application of hydraulic concentration to large scale operations has been effectively accomplished by the use of the SiphonSizer. Operation has been simple, automatic and essentially trouble free. The use of the primary desliming SiphonSizer on magnetic taconites has shown an improvement in grade of concentrate and an increase in recovery over conventional hydroseparators. Magnetic concentrates have been further deslimed and upgraded in SiphonSizers by floating a coarse middling product away from the heavier concentrate. The application of the Siphon-sizer to closed circuit grinding has met with only partial success to date. Hydraulic concentration of minerals has been practiced for a good many years. Until recently, however, the practice has been limited to equipment using a multiplicity of small pockets and relatively low tonnages and flows. The adaptation of the SiphonSizer to the concentration and classification of magnetite has changed this concept. Some fifty commercial units varying in size from a 16-ft diam circular unit to a 25x100-ft rectangular unit are currently in operation on magnetic taconites. Additional units up to 38 ft diam are under construction. Depending upon the application in the flowsheet, upgrading varies from 0.75% to 14% Fe in a single stage. To those not familiar with taconite processing, the importance of the struggle to remove economically as much silica as possible may not be fully appreciated. Perhaps some figures pertaining to transportation costs will underscore this important process. If the silica content of the concentrate from a 10,000,000 ton per year plant could be reduced by I%, a savings in boat freight, at $2.00 per ton, would amount to $200,000 annually! THE SlPHONSlZER The SiphonSizer, as illustrated in Figs. lA, 1B and 2, is a hydraulic classifier in which the hydraulic water is distributed uniformly across the bottom of the vessel by means of a system of headers (1 and 2), jet pipes (3), and nozzles (4). The depth of the teeter bed is automatically maintained by the siphon-float assembly. The feed is introduced through a feed well (5) and separated into two fractions by the effects of rising water and the density of the teetered bed. The magnetite fraction is discharged by the siphon (12) while the fine slime and light middling overflow a peripheral weir (9) to the overflow launder (6). The bed depth is controlled automatically by float valves (7), which are responsive to changes in the height of clear water supported in the superelevation tubes (8) by the density of the teetered bed. On top of the float (7) is a needle valve (10) which permits

Jan 1, 1963

By R. A. Metz, Michael M. Easdon, Michael J. Fiannaca

Disseminated epithermal gold metallization occurs within a breccia unit interpreted to be a submarine debris flow. Gold is associated with oxidized pyrite, fluorite, and jasperoidal silica. A minimum of 8 Mt (9 million at) of open-pittable mining reserves will be cyanide heap leached as run-of-mine ore at a rate of 0.9 Mt (1.0 million stpy). Careful evaluation of the combined results of successive sampling projects has established the pit plan, minable reserves, and process metallurgy of the operation. The sampling procedure utilized for a given test depended upon geological interpretation as well as the procedures, successes, and failures of previous tests. This paper summarizes the sampling and testing procedures of the development effort in light of the project goals and attendant problems in achieving them.

Jan 1, 1992

By E. Bauer, S. Moore

Technological advances in underground coal mining have led to a reduction in fatalities. This study demonstrated that the percentage of cumulative injuries remained largely unchanged across two decades of technological advances (1983-1984: 37%; 2003-2004: 33%). Furthermore, it was demonstrated that the average number of lost days due to cumulative injuries has increased (36±55 days and 62±82 days, respectively) which may have been due to the increased age of the work force or an increase in length of employment meaning that the mine workers injured in 2003-2004 had been exposed to ergonomic risk factors longer than those in 1983-1984. It is recommended that ergonomics processes be implemented as a means to systematically identify, prioritize, and resolve the root causes of these cumulative injuries.

Jan 1, 2007

In redesigning the cyanide plant at Mount Torrens, in conjunction with Mr. L. W. Grayson, the manager, several minor alterations were introduced in order to have the operations under thorough control, and these having proved serviceable may be of sufficient interest to merit a description here. The lixiviation vats, though only 8 feet in diameter, were retained, but the pipes leading away from the bottom were reduced from two inches to half-an-inch in diameter, and had a fall to the zinc boxes of about 4 feet. As these small pipes were completely filled by the solutions fiowing away from the vats, they exerted a suction equal to their fall and thus hastened the rate of flow, so that tailings containing a larger proportion of slimes could be treated than was possible where the larger pipes were used, as, there not being sufficient fiow of solution to keep the latter filled, no suction could be obtained with them. It was found that with'most of the tailings treated a sufficient flow could be obtained from the half-inch pipes when the taps on, them were only one-third to half open. The lower end of each of these pipes was connected by means on indiarubber tubing with the sille hole of 11 in aspirator bottle, and to the mouth of this bottle a few feet of similar tubing was connected, so that the solutions coming through could be directed into either of the fixed tubes leading respectively to the waste water tank the strong solution zinc boxes or the weak solution zinc boxes.In working the vats, the following method was found to give good results. While filling the vats with tailings the taps were left open, so that the water might drain off into the waste water tank the surface of the tailings was carefully levelled. When the strong solution was run in at the top, the air contained in the interstices of the tailings was forced through the half-inch pipe at the bottom as a strong blast, instead of, as I believe js usual, escaping by means of channels formed by it through the tailings, and thus tending, it would appeal, to render the disposition of the tailings less even and to make.

By Laxman S. Sundae

A U.S. Bureau of Mines designed and fabricated in-seam tester (1ST), retrofitted with a dust shroud, was used to establish a respirable dust index (RDI) and to determine cutting forces from a variety of bit types in four coal mines and a salt mine. Results from cutting tests at four coal mines showed that radial bits required the lowest cutting force and the least specific energy. Generally, for each conical bit the RDI and cutting force increased when the included bit tip angles increased from 70° to 90°. During field tests it was not possible to measure the total quantity of respirable dust produced by each cut; therefore, attempts were made to determine the amount of dust that became airborne from each test cut. The test results show that the quantity of airborne respirable dust is very erratic and cannot be related to bit type. Two statistical methods were employed to analyze RDI, but no correlation was found between the RDI and bit type. Despite scatter in test results for RDI, significant difference was found in RDI generated in four coal seams. In general, RDI increased with the increased cutting force for each coal seam from mine 1 through mine 4.

Jan 1, 1989

By C. W. Huggins

The objective of this Bureau of Mines research was to compare the size distribution of respirable quartz collected at coal mines with that of several reference standards used to quantify quartz in coal mine dust samples. Particle size measurements were made on 23 samples and 4 ref-erence standards using a scanning electron microscope in the backscatter electron mode of operation, interfaced with an image analysis system. The Mine Safety and Health Administration provided the 23 respirable coal mine dust samples, which were collected at surface and underground coal mines in 7 States. The accumulated particle size measurements in-dicate three of the reference standards, minus 5-um Min-U-Sil, minus 5-um Supersil, and NBS 1878, would be preferred over the fourth, Silver Bond B, for quantitative quartz determinations in coal mine dusts by X-ray diffraction and infrared spectrometry.

Jan 1, 1985

By Daniel J. Brunner

The U. S. Department of Energy (D.O.E.) requires that the prospective nuclear waste repository in Basalt at Hanford, Washington, comply with State of California mine and tunnel safety orders. These regulations require that all main fans be installed in such a manner as to permit prompt reversal of airflow. This paper evaluates the requirement of air reversal and the appropriateness of imposing such regulations on the proposed nuclear waste repository in Basalt.

Jan 1, 1988

By P. Breidt, E. S. Greiner

THIS note reports a determination of the melting point of germanium, and the liquidus of the Ge-Ga alloys; lattice constants of the a phase are given. The alloys were prepared by melting germanium (>20 ohm-cm resistivity) and gallium (99.6 pct) in evacuated silica tubes. The materials (50 to 70 g) were heated at 1000°C, held in the liquid state for about ¾ hr, and then cooled rapidly in the tubes. Points on the liquidus were obtained by thermal analysis which consisted of obtaining time-temperature data during heating and cooling the materials in high purity graphite crucibles and a helium at- mosphere. Temperatures were determined with a Pt—Pt-Rh thermocouple protected by a silica sheath. The couple was calibrated against a National Bureau of Standards calibrated couple and also against the freezing points of copper, silver, aluminum, and the 28.1 wt pct Cu, 71.9 wt pct Ag alloy eutectic. The samples for X-ray analysis were prepared by heating small pieces of the ingots in evacuated glass or quartz tubes at temperatures between 600" and 900°C for periods ranging from 2 hr to 22 days, periods deemed sufficient for equilibrium to be attained, followed by quenching in water. The heat-treated samples were ground to powder for X-ray analysis. The lattice constants of the germanium-rich phase (a) were determined with a baok-reflection focusing camera. The X-ray reflections (331 and 422 Cr Ka, 422 and 333 Cr KB) were corrected

Jan 1, 1956

By P. Schmieder

"The close vicinity of mining companies to other sites that are used for commercial and residential purposes or to areas under conservation as well as the fact that the people become more and more sensitive to emissions have led to a negative attitude towards mining operations in the neighborhood. It is above all the use of drilling and blasting techniques that give rise to objections, in the course of which demands for more environmentally-friendly production methods have been voiced. It is in this context that production methods without the use of explosives are considered as an option. After all, the use of such production methods is the only alternative for some quarry operators. The question is what are the true benefits of these techniques and what is the relation between a possible improvement of the environmental effects on the one hand and the technological potential as well as the costs on the other. It is intended to assess the mining techniques for solid rock in their entirety. This paper will therefore look at the aspects for assessing mining techniques in the context of their environmental impact and the costs."

Jan 1, 2005

By John P. Capp

In recent years limited markets have been developed for fly ash, the dust removed from coal-burning powerplant stacks, but most of it is still dumped in spoils areas at a cost ranging from 20 cents to $1.75 per ton. Aside from this cost, the creation of huge spoils areas can present a considerable aesthetic problem. Since the present annual fly ash output of about 20 million tons will probably reach 30 million by 1970, and because satisfactory disposal areas are becoming more limited, markets for much larger quantities of the waste are needed to keep disposal costs from becoming a significant economic factor in coal-burning powerplant operation. Current stress on air-pollution control and beautification, plus the vital need for good powerplant economy, makes it imperative, therefore, that coal producers and consumers expand markets and develop new applications for fly ash. Markets for established uses can be increased by making a greater effort to sell fly ash. New large tonnage markets for fly ash should be sought via more intensive, coordinated research. The economics of fly ash utilization underscores the vital role that must be played by research. To be competitive with other products, processes for the conversion of fly ash into marketable materials face difficulty in regard to two important economic factors--transportation cost and product utility--the other economic factors are favorable. Raw material costs of fly ash, for example, are quite attractive, and supply is no problem because there are many coal-burning powerplants in operation and many more are planned. Demand for products made from fly ash will grow if their utility is established and a good sales program is initiated. The major problems then are transporta¬tion costs and development of useful products.

Jan 1, 1966

By AIME AIME

THE 139th meeting of the Institute will be held Feb. 17-20, in the Engineering Societies Building, New York. The annual business meeting will be held on Feb. 18 at 10 a. m., and no technical sessions will be scheduled at that time, so that all members may participate in the election of officers, hear the presentation of the annual reports of officers and committees and discuss any matter which they may care to bring up at that time. The annual dinner will be held at the Conlmodore Hotel on the evening of Feb. 20, and the usual good time is promised. Arrangements for this and other social features of the meeting are, as usual, in hands of the New York Sec- tion, of which the chairman this year, Ralph M. Roosevelt, has a well-established reputation earned as president of the Zinc Institute, as host.

Jan 1, 1930

By lndu S. Das

An analytical simulation of the material characteristics of Inconel 718 is developed and bounds for mechanical and microstructural stability are obtained for isothermal and temperature-dependent cases. Experimental flow stress data using hot compression tests are reported for a wide range of temperature and strain at various strain rates. A parametric study of strain rate sensitivity, dissipation and entropy are presented. A complete set of processing maps delineating the stable and unstable regions are developed to help define the most efficient means of manufacturing an Inconel product.

Jan 1, 1992

By David C. Oyler

The Bureau of Mines is cooperating with the U.S. Department of Energy in a directional degasification project at the Emerald mine near Waynesburg, Pa. This project is designed to combine the highly successful underground horizontal degasification technology with surface drilling methods. The objective of this program is to demonstrate that directional drilling can be used as a technique for degasifying coalbeds ahead of mining to reduce the hazards of methane-air explosions in coal mines. The directional hole at the Emerald mine is designed to start vertically and enter the Pittsburgh coalbed horizontally. A 3-inch-pilot hole entered the Pittsburgh coalbed at a vertical depth of 999 feet. The hole will be reamed to 8-3/4 inches in diameter, and 5-1/2-inch casing will be cemented in place. Three individual 3-inch-diameter, 3,000-foot horizontal gas collection holes will be drilled into the coalbed in a "bird foot" pattern. A corehole and vertical dewatering hole have been completed at the anticipated coalbed intercept. The dewatering hole was drilled to 130 feet below the Pittsburgh coalbed, a depth of 900 feet, and 880 feet of 7-inch-OD casing was cemented in place. Seven vertical holes for monitoring the extent and progress of degasification have been drilled within the horizontal drilling area.

Jan 1, 1979

By A. G. Guy

Thermodynamic activity rather than chemical composition is basic to the analysis of diffusion. This is the essential conclusion reached by Darken1-3 and by Birchenall and Mehl.4 If so, it is reasonable to expect that diffusion calculations should be carried out using activities. This paper will illustrate a method of employing activities in analyzing interstitial diffusion. For interstitial diffusion (of carbon in iron and probably generally) the diffusion of the solvent atoms, volume changes, and other such complexities not explicitly provided for in the usual diffusion equations cause a negligible error of the order of 1 pct. Therefore it is relatively easy to test the validity of an analysis based on activities in the instance of interstitial diffusion. The mathematical treatment of the more complex substitutional diffusion could be simplified once the adequacy of the activity method had been established for substitutional diffusion. Thus the present work has the purpose not only of providing a superior analysis of interstitial diffusion but also of indicating a possible approach to the more important question of an adequate treatment of substitutional diffusion. Development of the Diffusion Equation Although activities are convenient quantities to determine experimentally, they are derived from the more fundamental fugacities.9 Possible confusion in using activities can be avoided by basing equations involving their use on the relationship, dP = -D1d/ax dt [I] where, dP = the number of grams of solute crossing one cm2 in the time dt sec. D, = the diffusion constant for use with fugacities; it is assumed to be constant at a given temperature, and has units of secs. f = the fugacity of the solute in the solid solution; the units are those of pressure, dynes per cm2. x = the distance in cm. Eq 1 can be considered to be the basic form of the first Fick Law for one-dimensional diffusion. In order to convert Eq 1 into an equation involving activities, a choice of a standard or reference fugacity, f°, must be made: then. a = f [2] where a is the activity corresponding to the fugacity f. However, the value of a is also determined by the relation, a = a\c [3] where a is the activity coefficient and c is the concentration. For a given value of a (such as a = 1) it is evident that the units used for expressing concentration will affect the numerical value of a corresponding to a given amount of carbon dissolved in y-iron. Since weight per cent concentration is so widely used, this unit will be adopted as the standard in this paper. When the value off given by Eq 2 is substituted in Eq 1, the first Fick Law becomes, dP= -D,f°dl [4] Since D,f° is constant (at a given temperature), the second form of Fick's Law can be obtained in the usual manner, -dt D'f° dx [5] where c' is the concentration in g per cm3. In terms of weight per cent concentration, c, Eq 5 becomes, dc _ 100 d2a Tt = T /f w [6] where p is the density of the solid solution and will be assumed to be constant. In order to simplify Eq6, it is necessary to consider the standard state, f°. Standard states are chosen for convenience. There appears to be one especially convenient choice for the analysis of interstitial diffusion. If the activity coefficient, a, is set equal to unity at infinite dilution of the solute, 100 then — 100D1fl° is approximately equal P to the usual diffusion constant in dilute solutions. This is true since the activity, a, in Eq 6 can be replaced by the concentration, c, with little error in an infinitely dilute solution.* Here f1° is the standard fugacity necessary to achieve this standard state. It is proposed that a diffusion constant Da' be defined, Da1=100/pD1f1° [7] where A is the metal whose diffusion is * The second derivative of a is equal to the second derivative of c in dilute solution only if -da/dr- is. zero. Although theory does not require this condition, in the systems C in Fe, and Zn in Cu, dc is in fact found to be essentially zero.

Jan 1, 1950

By Robert L. Sundeen, Richard V. Wenberg

Overshot loaders are loading machines which fill a front-mounted bucket by crowding and bucket lifting, passing the loaded bucket over the machine and throw¬ing the load into a haulage unit to the rear. The load is retained in the bucket as the load mass is accelerated in its path over the machine. At the point of discharge, the bucket is stopped suddenly and the load leaves the bucket, following the throw trajectory past the rear of the loader. Fig. 1 shows a typical overshot loader of this type. Overshot loaders were developed for loading in nar¬row drift headings and drawpoints, where it is impossible to place or pass a haulage unit alongside the loader. Haulage access is to the rear of all overshot loaders. The first overshot loader was developed in the early 1930s. The early machines were rail-mounted, air¬powered, and had small loading capacities. To this day, the same basic design configuration exists, and all suc¬cessful overshot loaders still use compressed air. Bucket sizes range from 0.14 to 0.59 m3 (5 to 21 cu ft). The most commonly used machines are rail-mounted, al¬though crawler versions are popular for special applica¬tions, particularly shaft sinking. Rubber-tired machines have found some application where a greater travel distance is required between the loading and discharge points. CONDITIONS INFLUENCING APPLICATION Roadway Type Rail-mounted loaders are used where soft bottom requires rail support or where the long haul is ac¬complished with rail. This situation usually occurs in civil tunnels or in mine drifts that will continue to utilize rail-bound main haulage after development work is completed. Crawler and rubber-tire mounted loaders are used where the roadway surface is rough and lateral travel beyond the range of rail-bound machines is required. Work Area Dimensions The largest rail-bound loaders can clean roadways as wide as 4 m (13 ft) from a single track. Wider headings require multiple trackage. Headroom require¬ments are dependent upon the path described by the bucket as it passes over the machine. The largest over¬shot loader requires approximately 3.4 m (11 ft) of headroom. It follows that the largest heading that can be driven by overshot loaders from a single set of rails is approximately 4 m (13 ft) wide and a minimum of 3.5 m (11.5 ft) high above the rail. The smallest rail-bound loaders can work efficiently in headings as small as 1.8 m (6 ft) wide by 1.8 m (6 ft) high above the rail.

Jan 1, 1982

By R. L. Grayson, L. L. Probert

"A three-year project focusing on the depth profiling of respirable coal mine dust particles using scanning electron microscopy coupled with energy dispersive X-ray analysis resulted in the development of statistically classified particle-behavior models. The models depict the changing silicon fraction for particles at 5-, 7-, 9-, and 11-keV accelerating voltages, thereby giving a clear indication of the nature of various types of mineral particles. This paper focuses on the results for respirable quartz particles sampled from five underground coal mines across the US. Through statistical analysis of results the relationship between the fraction of surface available quartz in respirable dust samples and coal rank is established for three Pennsylvania coal seams. IntroductionThis is the last in a series of papers detailing the results of SEM/EDX-based analyses of respirable coal mine dust particles collected from field sampling. Previous papers have detailed preliminary results and the statistical validity of the methodology (Grayson, Andre, and Simonyi, 1990; Grayson, 1991). This paper presents the final results of the analysis of respirable dusts from five coal seams with a range of coal rank:• Lykens Valley seam (anthracite), eastern Pennsylvania• Brookville (A) seam (mid-vol bituminous), central Pennsylvania• Pittsburgh seam (high-vol B bituminous), western Pennsylvania• No. 6 seam (high-vol C bituminous), Illinois• Wadge seam (sub-bituminous A), ColoradoSEM/EDX-based techniques were applied to try to clarify the role of quartz as an etiologic agent in coal workers' pneumoconiosis (CWP). It was hypothesized that previous studies were hampered by the restrictions of bulk analysis techniques and that particle-level analyses were needed to answer a number of questions concerning the role of quartz in CWP and its progression.Since 1985, a large number of the respirable dust samples submitted to MSHA are analyzed for free silica (Tomb, Parobeck, and Gero, 1986). Our reasearch shows that conventional bulk analysis techniques may not give a true indication of the biologically available, or active, quartz in mine dusts. Analytical evidence indicates that respirable dust samples may contain many quartz particles that are occluded, or coated, resulting in a bulk analysis for ""free silica"" that may not be indicative of the biologically available quartz surface."

Dec 1, 1996

By E. S. Peterson

The selective separations of trace metals- and organics from water are processes of importance to industry. The application of a new metals capture technology coupled with polymer membrane technology has proven to be one avenue to accomplish such selective separations. The polymers used in these studies are polyphosphazenes. Polyphosphazene polymers consist of an alternating backbone of nitrogen and phosphorus atoms. The polymers have high thermal and chemical stabilities. Experiments at the Idaho National Engineering Laboratory demonstrate that polyphosphazene membranes coupled with Chromato Chem,"Chelation Chromatography" process are capable of removing both chlorinated hydrocarbons and metal ions from process streams. These results point to a wide range of potential industrial and environmental applications for such systems. Data will be presented which show the efficiency and selectivity of separations, postulated separation mechanisms, and the initial designs of industrial demonstration units which are currently under construction. Parts of this work have been performed under a Cooperative Research and Development Agreement (CRADA) between ChromatoChem, Inc. and Idaho National Engineering Laboratory (INEL). The work at INEL was been sponsored by the United States Department of Energy's Office of Industrial Technologies

Jan 1, 1995

By Brian Hall

For some years, the mining industry has been consistently delivering returns below the market average. One of the causes is a disconnect between what is perceived to drive value creation by many industry analysts and senior corporate executives, and what actually drives the intrinsic value of mining operations. The perverse effect is that strategies that should increase value are perceived to have the potential to drive share prices down, and vice versa. This paper challenges common perceptions of what drives a mining company?s value. Anecdotal evidence suggests that the key drivers of value in the market, and hence in many boardrooms, are such things as increasing the reserves and production rate, and reducing unit operating cost. However, while the quoted reserves may satisfy ore reserves reporting code requirements to be economic, this does not imply that they are optimal. Often, a proportion of the quoted reserve reduces the potential value of the operation. Metal price increases, increased production rates, and operating cost reductions are all seen as conditions or actions that can improve value, and lead to cutoff grade reductions, thereby increasing ore reserves. However, modern cutoff theory and studies conducted by the author and his colleagues show clearly that, while breakeven cutoff grades will fall in these circumstances, optimum cutoffs may be much less volatile, and may even increase. Results from case studies indicate that value is maximised by right-sizing, not maximising, the production capacities, and by optimising the cutoff strategy. Values of many existing underground mining operations can be increased significantly by a substantial cutoff grade increase. Also, an increase in downside risk, and hence reduced returns, can occur using typical life-of-mine planning strategies if prices received are lower than predicted. Since this is often the case, low industry returns may be a direct result of typical strategic mine planning processes. Relatively simple cost-effective techniques are available to provide senior decision makers with information needed to assess the tradeoffs between their many conflicting corporate goals, and the balance between risk and reward. Often this information is not being generated at all. If it is, decisions affecting the value of the company are occurring by default at relatively low levels within the hierarchy, with senior executives apparently unaware of them or their potential impact. The paper concludes that without a re-evaluation of the way mining projects are valued, to demand proven value optimisation from mining plans by boards and mining analysts, the industry will continue to deliver below average returns.

May 1, 2003

By Louis W. Towle

A brief history of the use of Ammonium Nitrate in explosives and blasting agents is given. Methods of manufacture and physical properties of the various types of Ammonium Nitrate are given with particular reference to their use in blasting agents Important properties of blasting agents discussed are sensitiveness, methods of initiation, velocities of detonation, strength, density, products of detonation, rate of pressure development, and borehole pressure.

Jan 1, 1959

By Maria I. De Rosa

High temperatures encountered by mine rescue teams during emergency situations may cause severe physiological strain, hindering the men from carrying out rescue and recovery missions. A prototype ice-cooling garment (ICG) was developed by the Bureau of Mines to alleviate physiological strain due to heat stress. The effectiveness of the garment was tested with acclimatized and unacclimatized subjects at a typical work rate (1,200 Btu/hr) expected during rescue operations and at various hot environments (97° to 113° F dry bulb and 80° to 89° F wet bulb). During exposures with the ice cooling garment, the subjects were able to maintain a safe deep body temperature of 100.4° F or below Without the garment, the deep body temperature rose beyond values of 100.4° F, a condition considered unsafe for continuous work in hot conditions. Both heart rate and skin temperature values were lower while wearing the ICG. Subjective observation also indicated a marked benefit by wearing the ICG.

Jan 1, 1976