Search Documents

By H. Hance James

SOME of the outstanding features of petroleum production in Illinois during 1923 were: (1) Sustained production from the older wells, due to cleaning and deepening; (2) good results from new drilling in a few localities; (3) large percentage of dry holes, many of which were ill advised tests, with a resulting high cost of the new production; (4) decrease in the number of productive wells in the state; (5) low average price of crude petroleum, a serious factor over the entire country. FIG. 1.-ANNUAL TOTALS OF ILLINOIS PRODUCTION. The total production of Illinois for 1923 was 8,710,000 bbl.,1 a decrease of 7.2 per cent. from that of 1922. Of this amount, it is estimated that about 8,500,000 bbl. were produced by old wells, many of which had been cleaned and deepened somewhat, and approximately 210,000 bbl. were obtained from the new wells drilled during the year. About 95 per cent. of the oil comes from the southeastern field in Clark, Crawford, and Lawrence Counties, where production is almost entirely from Pennsylvanian and Mississippian rocks. Extensions of the productive area were made in Clark, Wabash, Marion, and Jackson Counties. Some important gas development has been accomplished near Jacksonville, in Morgan County, and at Gillespie, in Macoupin County.

Jan 3, 1924

By K. K. Mamyrbayeva, G. Z. Guseinova, V. A. Luganov

This paper presents the results of theoretical and technological studies on leaching ore of Bozshakol deposit. The major oxidized copper mineral of Bozshakol ore is atacamite, and the content of malachite, azurite, cuprite, copper sulfide minerals is insignificant. The chemical composition of the test sample, with mass, %: 0.9 Cu; 55.00 SiO2; 22.40 AI2O3; 9.00 Fe2O3; 2.24 CaO; 3.56 MgO. Technological studies on leaching the ore were carried out with sulfuric acid 5, 15, 25 and 50 g/dm3 in one and multistage (up to 4 stages) countercurrents. Size of ore 1 mm, the ratio S : L 1: 4. It was found that with increasing of acid concentration from 5 to 50 at one-mode leaching the copper extraction reaches 55 %. At multistage leaching the copper recovery reaches 73 %, a productive solution containing g/dm3: Cu - 4; Fe – 1.2; Al – 1.1 at a pH of 2.8. When leaching the cinders obtained by ore roasting in an atmosphere with limited value of oxygen, with increasing of the roasting temperature from 650 up to 750 °? the extraction of copper from the Bozshakol ores reduced from 31.5% down to 24.4%. The rate of filtration is markedly increased compared with the crude ore. When leaching the cinders obtained by roasting in a nitrogen atmosphere a marked increase up to 87.2-88 % of copper extraction from Bozshakol ores is observed. As an extractant for the extraction of copper from the pregnant solution used LIX984N extractant in kerosene. On the basis of the calculations it was built extraction isotherm and modeled processes of copper recovery with the circuit 2E + 1P, allowing up to 93 and 96% extraction. The through extraction of copper from the ore in the electrolyte was 67 %. Technology is recommended for semi test.

Jan 1, 2016

By A. R. Miller, R. A. Stanton, M. J. Male, G. R. Cluff

"The Dubawnt Group consists of continental sedimentary and volcanic rocks which fill structural depressions - Baker Lake Basin, Yathkyed Lake and Angikuni Lake subbasins- whose evolution was controlled by late Aphebian extension, between 1.9-1.8 Ga. Structurally controlled uranium mineralization having the signature U + Mo + Ag + Pb + Cu ± Zn is spatially related to (i) intersecting fault systems that record multiple movements, (ii) chemically reactive lithologies containing sulphide, chlorite or graphite/ carbonaceous matter in the Archean and Aphebian basement complex and as alkaline volcanics of the overlying Dubawnt Group and (iii) areas containing thick successions of basal Dubawnt Group red clastic sediments.The most significant uranium occurrence found to date is the Lac Cinquante deposit, which contains 14 million pounds U3O8 of drill-indicated reserves. Mineralization is hosted in Archean meta-volcanic and metasedimentary rocks of the Henik Group adjacent to the basal Dubawnt unconformity in the northeastern A ngikuni Lake subbasin and occurs as plunging pods in and peripheral to a fractured and brecciated tuffaceous meta-sediment- sulphide+ carbonaceous exhalite. This deposit exhibits many features typified by the classical vein deposit at Beaverlodge, northern Saskatchewan.Epigenetic stratabound U + Cu + Ag ± Mo mineralization, typified by the 74-1E prospect in the eastern Baker Lake Basin, is hosted in thermally altered Kazan redbeds adjacent to alkaline dykes.At the eastern end of the Baker Lake Basin, small prospects having an elemental signature U + Se + Cu + Ag +Au are interpreted as unconformity-related mineralization associated with the Helikian The/on Basin.The Dubawnt Group rocks of the Baker Lake Basin, subbasins and adjacent basement complex contain uranium mineralization of two eras- Late Aphebian and Helikian."

Jan 1, 1986

By K. Lapakko

One responsibility of the Minnesota Department of Natural Resources is to encourage the development of mineral resources within the state. A second responsibility is to ensure that mineral development does not adversely impact other natural resources, including the water resources of the state. One approach the Division of Minerals has taken to fulfill these responsibilities is to conduct cooperative research with the mining industry. To encourage mineral development the Division has cooperated with industry on projects related to exploration, mining, and mineral processing. To examine environmental issues the Division has worked in concert with iron ore, base metal, and precious metal exploration and mining companies, as well as the Western Governors' Association, US Bureau of Mines, US Bureau of Land Management, and the US EPA for the past 20 years. These projects were conducted to evaluate methods of predicting, preventing, controlling, and treating problematic mine waste drainages, as well as mine waste revegetation. This paper I) briefly summarizes cooperative projects conducted, 2) enumerates elements which have contributed to the success of cooperative projects, and 3) describes changes implemented for future projects at the Division's new field and laboratory research facilities, as well as at existing mine and plant sites.

Jan 1, 1998

By David Roncalla, Emma Flores, Juan Pérez

Se ha co creado a Rurana, Centro de Innovación Social de Asociación Pataz, para coadyuvar en el abordaje de los desafíos de triple impacto, basados en la innovación como un evento sistémico con direccionalidad de largo plazo, pero con pasos de corto y mediano plazo para desarrollar las capacidades requeridas para el logro de Misiones, propósitos de gran impacto enmarcados en la teoría de Mariana Mazzucato.

Sep 29, 2023

One of the first all-hydraulic crawler drills in service at a US open-pit mine has significantly exceeded the penetration rates of comparable pneumatic crawler rigs, according to Atlas Copco Inc. Overall production with the hydraulic unit has been double that of pneumatic crawlers in use. The installation is at the Foote Mineral Co. surface mine at Kings Mountain, N.C., where the company is engaged in mining spodumene, a combination of lithium, aluminum, and silicates. The ore is found in pegmatite dikes, a tough and abrasive host rock with compressive strength of tip to 5800 kPa (40,000 psi).

Jan 9, 1978

By T. M. Jones

This paper outlines the development of the theory of controlled district recirculation and indicates the advances in understanding and technology which have enabled a major change in established ventilation practice. An insight is presented into the possible future use of controlled district recirculation as acceptable practice in mine ventilation planning.

Jan 1, 1987

By F. A., King

THE problem of the proper size and capacity of the open-hearth furnace has been a predominant issue ever since its inception some sixty years ago. The original furnaces, built in 1868 at Landore, England, were only to 3 to 4 tons capacity, and from' this there has been a steadily increasing and almost uniform rate of expansion until furnaces producing 300 tons are in successful operation today. At the end of the first half of this 60-year period, or about the year 1900, 50-ton furnaces we're common. Up to this time the problems of expansion had been largely those relating to suficient capital and the engineering development of larger units. But as 75, 100-ton and larger furnaces were proposed apprehension grew and other questions assumed leading consideration.

Jan 1, 1928

By R. R. Brandenthaler

Petroleum producers in the Mid-Continent field, up to the present time, have been more concerned with the mechanical operation and efficiency of the gas-lift than with its possible effects on the physical properties of the oil. As a result few specific data are available on the subject and contradictory opinions exist. Some operators are positive that the gravity of the oil is decreased, while others present data which definitely show that the gravity of the oil is increased. In other localities, some operators have given careful attention to the effect of the gas-lift on the gravity of the oil. When the emulsions formed have given much trouble, the problem has usually been dodged by placing the well on the pump. Certain Fundamentals Certain fundamental results may be expected under ordinary conditions and with all types of crude oil, when gas is the prime mover of oil in producing formations. For example, the gravity of oil will decrease as the rock pressure in the producing formation declines, the change being greater in the higher gravity oils. Furthermore, the character of emulsion formed is primarily dependent on the kind of oil, thus more refractory emulsions are formed from asphaltic-base oils, less refractory from mixcd-base oils, and the least refractory from paraffin-base oils. However, refractory emulsions are sometimes formed from paraffin or mixed-base oils that are difficult to treat by ordinary methods, especially by electrolytic processes. With oils having the same base, those of lighter gravity are less subject to the formation of emulsions, especially of refractory emulsions. There are two types of emulsions formed; namely, water-in-oil emulsions and oil-in-water emulsions. The former are the more common; in fact, very few examples of oil-in-water emulsions have been noted in the oil fields. The amount of water produced with the oil influences the percentage of emulsion formed. Agitation and velocity of flow play an important part in the forming of emulsions.

Jan 1, 1928

By Leslie C. Taylor, Scott A. Yamada, William L. Fourney

Previous studies have shown that the pressure load on a target by a buried explosive charge is not smoothly distributed. The effort reported here was undertaken to explore the mechanisms believed to cause this uneven pressure distribution: jets from the surface originating in instabilities caused by the explosive shockwave interacting with surface irregularities. Small-scale tests using conical, hemispherical, and cylindrical indentations in the sand surface above a buried charge were conducted to identify trends in the velocity and form of the resulting jets. In these tests, the most important factor affecting the resulting jets was the distance between the bottom of the indentation and the top of the charge. Cylindrical indentations resulted in higher jet velocities than those from comparable hemispherical and conical indentations.

Jan 1, 2012

By J. R. Kadambi, E. Kucukal, J. Furlan

"Hydrocyclones are used in various industrial applications, including mineral processing and tailings management, to separate or classify solid particles and/or liquid droplets from multiphase feed. The fluid flow in a hydrocyclone (used in mineral processing) was investigated numerically and experimentally using particle-image velocimetry (PIV) and refractive index matching techniques. Two turbulence models were used in the calculations: the k–? model and the Reynolds stress model. Particle image velocimetry measurements were taken at various spatial locations along the cyclone. Computational results were validated globally using pressure and flow-rate readings at the boundaries, and locally by comparing the PIV velocity-vector maps and profiles.RÉSUMÉ On utilise les hydrocyclones dans diverses applications industrielles, dont la minéralurgie et la gestion des résidus, pour séparer les particules solides et/ou les gouttelettes liquides de l’alimentation polyphasée, ou pour les classifier. Une étude numérique et expérimentale sur l’écoulement des fluides dans un hydrocyclone (dont on se sert en minéralurgie) a été menée à l’aide des techniques de vélocimétrie par images de particules (PIV, de l’anglais particle image velocimetry) et d’appariement des indices de réfraction. Deux modèles de turbulence ont été utilisés dans ces calculs, à savoir le modèle de turbulence k–? et le modèle aux tensions de Reynolds (RSM, de l’anglais Reynolds stress model). La valeur de la PIV a été mesurée à diverses positions spatiales le long du cyclone. Les résultats de ces calculs ont été validés globalement à l’aide de relevés des pressions et du coefficient d’écoulement d’une extrémité à l’autre de l’hydrocyclone, et localement à des coordonnées spatiales spécifiques en comparant les cartes et les profils du vecteur vitesse PIV."

Jan 1, 2017

By Merline W. Van Dyke

The Surface Mining and Reclamation Act of 1977, PL 95-87 (The Act) granted the Office of Surface Mining (OSM) the duty of collecting fees from the active coal mining activities to be used in abating the hazards associated with abandoned coal mines. Since the passage of the Act, OSM has been instrumental in closing a multiple of mine hazards and in full cooperation with the states involved. Complete mine closures range from simply filling a subsidence hole to exodic designs costing thousands of dollars, such as in the case of the Portal Park swimming pool in Colorado Springs, Colorado. The Portal Park olympic sized swimming pool was built over an abandoned coal mine by a group of local citizens and given to the city of Colorado Springs. This pool receives the largest number of users each year. During the past four years, OSM has abated six mine related hazards in and around the pool. During the summer of 1982, the pool started tipping causing the pool waters to run out the west end. This pool tipping and the associated cave-in problems caused great concern to the city and the local users. This citizens concern generated a request from the city for OSM to assist in checking out the pool problems. Early in 1983, OSM initiated a driling program to investigate the subsurface voids. This drilling effort revealed several large voids within a few feet of the pool deck, with all voids inundated with ground water. Therefore, the void filling method favored the hydraulic backfilling needed to be confined to the area under the pool. This confining problem lead to the development of the gravel bulkhead cutoff walls to confine the backfilling effort to the areas under the swimming pool.

Jan 1, 1985

By H. T. Green, R. M. Brick

True stress-strain data on alloys of pure iron with up to 2.4 pct Al were obtained in the temperature range +100° to —185°C. Alumi-num was found to reduce yield and flow stresses of iron at low temperatures but to have little or no effect on ductility. The effects of temperature and composition on strain hardening are discussed. SEVERAL independent studies of the behavior of high purity iron binary alloys at low temperatures are now in progress in attempts to evaluate systematically the variables affecting the low temperature brittleness of ferritic steels. This paper reports the results of one such investigation in which the tensile properties of aluminum and aluminum plus silicon ferrites were measured from 100" to —192°C. True stress-natural strain data have been obtained in order to evaluate as many as possible of the parameters which describe the behavior of the materials involved. In comparable studies at the National Physical Laboratory in England, iron and iron alloys of high purity have been produced' and tested at subat-mospheric temperatures.' True stress-natural strain curves were obtained there also. The purest iron contained 0.0025 pct C and 0.001 pct O and N. Even this, as normalized at 950°C following hot rolling, showed little ductility at -196°C. The grain size was ASTM No. 3, and the room-temperature yield strength was 17,800 psi (which seems too high for pure iron). Some of the NPL irons contained considerably more oxygen and demonstrated intergran-ular fracture at —196°C. The authors2 carefully differentiated between intergranular fractures associated with excessive oxygen content and transcrys-talline cleavage with little ductility encountered at —196°C in the purer material. The cleavage stress was half again as great as that associated with inter-granular fracture. Test Material, Preparation, and Procedures Of a number of Fe-A1 alloys produced, eight were considered to be sufficiently pure for testing. Partial chemical analyses (Table I), low observed yield points, and high ductilities indicate these alloys to be comparatively pure for vacuum-melted irons of sizable ingots, 5 Ib or more. To produce the binary Fe-A1 alloys, electrolytic iron was melted in air, cast into slabs, and rolled to strips 0.010 in. thick. These strips, joined into a continuous ribbon and wound into 2 1/2 in. diameter spools, were subjected for four weeks to a moving atmosphere of purified dry hydrogen in a stainless-steel tube at 1050" to 1150°C. Charges of these spools were melted in beryllia crucibles under good vacuums (1 micron), and aluminum (99.97 pct Al) was added to the melts. Compositions of these alloys are recorded in Table I. The ingots were hot forged and then cold rolled at least 65 pct to 3/8 in. rods which were vacuum annealed to the desired grain size, approximately ASTM No. 4, prior to machining into tensile test bars. All tensile specimens had gage sections 1 in. long, with a fillet of 1.5 in. radius to the shoulder. Gage diameters were 0.250 in, except for a few rods where additional cold work required use of a 0.200 in. gage section. After machining, 0.002 in. was removed from the gage diameter using 240, 400, and 600-grit metallo-graphic papers. The final polish with 600 grit left the fine scratches running in the longitudinal direction. By this means, surface metal strained during machining was removed. A few specimens heat treated after machining were similarly reduced 0.004 in. to remove any material affected chemically by the atmosphere during heat treatments, as is discussed in a later section. Tensile tests of the eight alloys at constant temperatures from +100° to —185°C were performed in apparatus which has been described." The essentials include a double-walled insulated metal vessel which contained the liquid heat-transfer medium surrounding the test specimen. A constant temperature was maintained by means of a pyrometer which regulated the pressure of dry air driving liquid air through a copper coil. Temperature variation was less than ±2°C during a specific test. For axial straining, two lengths of case-hardened chain, terminating in simple shackles, loaded the specimen through threaded grips. The lower grip bar passed through a hole in the bottom of the test vessel to which it was joined by a thin-walled

Jan 1, 1955

By Q. Chen, J. H. Zhang, M. Zhang, F. M. Zheng, Y. J. Zhang

The characteristics of air bubbles and gas dispersion in KYF flotation cell are studied using the method of the point conductivity probe and CFD simulation. With increasing of speed, the velocities of air bubbles increase slowly and the distribution of diameters exhibits little change. With increasing of aeration rate, the gas holdup is increased. However, the velocities and diameters of bubbles have no great change. The CFD predictions on gas holdup have good agreement with the experiment results. The gas holdup distribution in the center section is revealed. The gas dispersion in the middle and upper part of flotation cell is uniform. It would be helpful for bubbles and solid particles collision. The gas holdup of the lower part of flotation cell is scarce, and it agrees with the observation in experiment. The gas would accumulate at the suction side of impeller blades, and it would decrease the power consumption. The rotating speed and aeration rate have great effect on gas dispersion. With increasing of aeration rate, the gas holdup of flotation cell will increase. The increasing of speed would improve gas dispersion. The results are expected to help to optimize the performances of KYF flotation cell.

Jan 1, 2015

By T. T. Chen

Copper anodes generated from copper scrap are relatively rich in Sn, Zn and Fe. Because of the presence of oxygen, only trace amounts of Sn occur in solid solution in the copper crystals. Thus, Sn occurs mainly as SnO2, Cu-Sn-Ni oxide and Sn-Ni-Zn oxide in the copper anodes, and Zn and Fe occur mainly as minor constituents in the Sn-Ni-Zn oxide and Cu-Sn-Ni oxide. During electrorefining, these oxide species are liberated from the copper anodes and report directly to the anode slimes. The trace amounts of Sn present in solid solution in the copper crystals dissolve but reprecipitate as Sn arsenate or a Sb-As-Sn-O phase. Accordingly, high Sn contents in copper anodes do not lead to elevated Sn concentrations in the electrolyte.

Jan 1, 2010

By M. Matema

Paper written on project work carried out in partial fulfilment of BSc (Eng.) Metallurgy and Materials Engineering Small and large welded aluminium specimens were tested in fatigue and the results compared with design curves for aluminium in specification BS8118. Metallurgical tests were also performed on the specimens in order to correlate microscopic and macroscopic phenomena. The small-scale fatigue test results were in reasonable agreement with results in BS8118, whereas the large-scale fatigue tests showed that BS8118 is conservative.

Jan 1, 2005

By R. L. Garrett

The quality of mineral additives used 1n a drilling fluid (mud) can dramatically affect the fluid's properties and the overall cost of drilling an oil or gas well. The principally used minerals are bentonite, barite, barite/hematite blends and hematite alone. The high specific gravity minerals, barite and hematite, are used to increase drilling fluid density. Bentonite clay is used to increase drilling fluid viscosity, gel strength and to provide a low permeability filter cake. A multi-million dollar investment in a well and the safety of the personnel on the drilling rig can depend on how effectively these mud additives perform with other constituents in the mud. This paper points out effects caused by small amounts of certain carbonate and sulfide mineral impurities in barite or hematite and how polymeric extender additives in bentonites contribute to unpredictable behavior of a mud. Effects like these are the reason why oil companies who use these materials sometimes set their own quality standards beyond those already specified in API Spec. 13A. Also discussed in this paper are the current standardization activities in API Committee 13 on these minerals.

Jan 1, 1986

By Carl Hendricks

Aquila Mining Systems Ltd., is the world leader in drill monitoring, control and GPS-based machine navigation systems for the mining industry. This paper will review the design and application of AQUILA’s drill monitoring, control and positioning systems currently in use throughout the world and some of the benefits that derive through their use. In 1993, AQUILA became the first company to install a high precision, cm level, real-time GPS receiver on a blasthole drill. In fact, this was likely the first application of GPS on any form of production mining equipment. To date, AQUILA has installed over 90 GPS based drill monitoring systems worldwide. Since 1992 AQUILA has continued to lead in the advancement of new technologies for drilling including real-time geology recognition and automated drilling control systems. The AQUILA DMseries drill systems offer mines the ability to collect and transmit to the mine office; drill production statistics, ore and waste intersections, exact collar elevations, hole positions and depths, maintenance information and consumables tracking. Unique office software developed by AQUILA provides an encompassing Windows environment within which to manage and coordinate all aspects of data communications and information management between the drills and various mine departments. AQUILA and Caterpillar, along with Mincom and Trimble Navigation are partners in a technology alliance that is providing the surface mining industry with vehicle tracking and navigation systems for all mobile production equipment.

Jan 1, 2000

By William C. Maurer

A survey of 25 novel drills has shown that spark drills have potential for drilling oil wells and blastholes at higher rates than rotary drills. Available laboratory and field data were extrapolated to drilling rates of 70 to 280 fph for full-scale spark drills. Most of the data used in these extrapolations were from small-scale laboratory tests at atmospheric pressure. Accurate extrapolation of the small-scale spark drill tests to full-scale field drills was complicated by the fact that the effect of fluid pressure in the well bore and the effect of spark size were not known. In order to answer these questions and to more accurately evaluate the potential of spark drills for drilling blastholes and oil wells economically, a high-voltage spark discharge system was assembled. This equipment produced powerful sparks (10,000 joules) equivalent to those that would be used on a 100-kw full-scale field drill. These sparks are 100 times more powerful than those previously used on spark drills, thus eliminating extrapolation of the spark size. In addition, a pressure chamber was modified to enable using these sparks to produce craters in rocks at fluid pressures up to 15,000 psi, thus eliminating extrapolation from atmospheric pressure to the high pressure existing in deep oil wells. These tests have provided considerable information for more accurately evaluating spark drills for oil-field drilling. MECHANISM AND THEORY OF SPARK DRILLING Spark-Drilling Mechanism When a high-voltage capacitor is discharged across two electrodes, the dissipated energy produces a high-temperature, high-pressure plasma for a few µsec. When these sparks are discharged in air, they undergo considerable expansion (Fig. 1) and produce low-pressure pulses (103-

Jan 1, 1970

By J. A. Cavallaro

To determine whether magnetite consumption could be reduced and salable coal production increased by using froth flotation units in series with magnetic separators, the Bureau of Mines conducted laboratory froth flotation tests on primary magnetic separator effluents obtained from three coal preparation plants. Tests were performed in a standard 500-gram-capacity laboratory batch flotation cell. Oleic acid and methylisobutyl carbinol were used as the collector and frother, respectively. Magnetite recovery was comparable to that expected from secondary magnetic separation, and salable float coal recoveries of 0,8 to 7.6 tons per hour were obtainable. The economics of the proposed technique appear to be sound.

Jan 1, 1966