Search Documents

By Y. Sasseville

"Niobec has been using vibrating screens and screw classifiers as a double stage classification in its grinding circuit since the very beginning of its operation in St-Honoré. Most of the other mineral processing plants around the world uses cyclones as the classification device in their grinding circuit. The difference between these two methods are well known in terms of capital cost and grinding efficiency but the differences in terms of the impact on the downstream processing stages are a lot harder to predict and are case specific. In the interest of lowering the capital cost of a future expansion project, Niobec decided to test the cyclones in its actual grinding circuit and evaluate their impact on the recovery of the downstream processing stages as well as the operating cost of the mill. We switched between cyclones and screens for 8 month in 2013 and early 2014 and we are now operating only with cyclones since march 2014.INTRODUCTIONThe Niobec mine and concentrator were built in the mid 70’s and at that time, the mill was processing 1 500 tons per day. Over the years, many expansion projects have brought the plant to 7 000 tons per day. Throughout the initial concentrator design and commissioning, screens have been chosen over cyclones because of their higher classification efficiency which is known to reduce variability and limit the fine generation especially due to a high undersize classification efficiency. Just like many other plants, fine particle generation is a major problem at Niobec because of its negative effect on downstream processing stages. In the interest of lowering the capital cost of a future expansion project, Niobec’s engineering team decided, 35 years later, to test the cyclones in its actual grinding circuit and evaluate their actual impact on the final recovery and the operating cost of the mill.The grinding circuit is separated in two lines which will be called Circuit #1 and Circuit #2 along this paper. Circuit #1 is, as you can see in Figure 1, composed of a rod mill and two parallel ball mills in closed circuit with screens and screw classifiers. The screens oversize are sent to the screw classifiers while the undersize are sent to the next processing stage. The screw classifiers overflow are both sent back to the pump box while their oversize streams return in their corresponding ball mills for further grinding. Circuit #2 is, as you can see in Figure 1, quite the same as Circuit #1 except it has only one set of screw classifier and ball mill. Figure 1 also shows the modification in arrangement each circuits went through to integrate the new cyclones. One of the ball mills in Circuit #1 now appears dotted because it can still be used but is not now"

Jan 1, 2015

By Madan M. Singh

Although roof bolting has been a major means of strata support for nearly two decades, little attention has been directed towards the design of bolt Installations. The variables involved are interdependent and their study complex. However, some simple tests may be employed to serve as guides to the efficient design of roof bolt systems. Local conditions are continually varying and are important to pattern design. This paper discusses such considerations and suggests techniques which may be employed to effect improved roof control with bolts.

Jan 1, 1967

By D. Brand

"The risk management objective of the AMIRA Code of Practice for Metal Accounting has seldom been systematically investigated in the literature up to the authors’ knowledge. Risk is defined in the Australian Standard on Risk Management (AS/NZS 4360:2004), as “the chance of something happening that will have an impact on objectives”. The simplified economic analysis performed in this paper has lead to define “something happening” as measurement non-representativity and “impact on objectives” as NSR loss from the optimal NSR. This has pinpointed a missing link being the establishment of a relation between NSR in flotation plants and measurement representativity. The proposed framework, referred to as the total cost of representativity, answers the previously unanswered question of how much accuracy/reproducibility is fit for purpose in a given flotation plant. Authors readily acknowledge that it is way easier to assess the cost of accuracy/reproducibility than the cost of inaccuracy/irreproducibility. However, this exercise not only answers previously unanswered questions but also establishes an essential link with operational excellence. This paper exposes why such operational excellence could neither be attained nor proved without a state of the art metal accounting system. This should impact not only how metal accounting systems are audited/designed/refactored, but also how flotation plants are designed.IntroductionBecause representative metal accounting is a vital source of information for the financial accounts of a mining/metallurgical company, the need for a code on metal accounting was recognized in 2001 and a team was formed in 2003, under the sponsorship of several major mining houses, to produce such a code. Table 1 exposes the two main objectives of this AMIRA Code of Practice for Metal Accounting."

Jan 1, 2017

By Rei Arai, Yuta Yamamoto, Tetsuo Yamazaki, Naoki Nakatani

"Methane hydrate is of interest as an alternative energy resource in Japan and the R&D program has been ongoing for ten years (MH21: http://www.mh21japan.gr.jp/english/). Rare-earth element-rich deep-sea mud (REE Mud) is also of interest as an alternative resource in Japan and an exploration program has been launched in 2013.For methane recovery from the hydrate, a depressurization method pumps up water in a production well and has been successfully applied in field production tests (MH21: http://www.mh21japan.gr.jp/english/). However, micro-bubbles, which appear in the hydrate dissociation and water recovery processes may present an environmental issue. It may stick on clay and silt particles that accompany the recovered water, and may disturb settling of the particles in the water separation tank. For exploitation of REE Mud, an air-lift system has been proposed in the feasibility study (Abe et al., 2012). The same micro-bubble issue is expected during the air, water, and mud particle separation processes. In this research, the authors conducted a preliminary tank experiment for clarifying the effect of micro-bubbles on settling behavior of fine kaolinite particles. The behavior was continuously recorded by a still camera and the images were analyzed by the gray scale intensity. From the results the authors found a suspension effect for the settling of fine particles as the result of micro-bubbles. The effect should be studied in detail for preventing some serious environmental impacts during deep-sea mining."

Sep 1, 2014

Develop quieted, hand-held pneumatic percussion drills that can replace standard hand-held drills in many underground mining applications. The Problem Percussion drills are the noisiest machines used in underground mines; noise levels of 115 to 120 dBA are common, requiring the use of hearing protectors and limiting the time a miner is permit-ted to operate the drill during an 8-hour shift. Hand-held pneumatic percussion drills pose a particularly difficult problem because the operator cannot be isolated from the noise source (e.g., an acoustical cab), and alternative technologies for drilling roof bolt holes and blastholes in tight quarters are not readily available.

Jan 1, 1984

By J. H. Zietsman, M. W. Erwee, Q. G. Reynolds

Pyrometallurgical furnaces, essential for metal extraction, operate at temperatures exceeding 1600°C and represent complex multiphase systems that challenge direct industrial research. Multiphysics models play a key role in shedding light on their intricate behaviours, supporting the refinement of design and operational strategies. Integral to the operation are the tap-holes, which facilitate the removal of molten products and are routinely opened by lancing, a process comparable to the use of a cutting torch, where high temperatures result from oxygen reacting with an iron lance. When the lance pierces the clay, oxygen gas enters the furnace, which could influence the behaviour of the molten material inside. In this work, a multiphase fluid flow model was used to investigate bulk flow dynamics, with a focus on the effects of the lancing process on the inside of the furnace, immediately behind the tap-hole. Incompressible and compressible multiphase fluid solvers were used and compared with respect their performance – the intention was to assess whether using a compressible solver would yield a different solution to the incompressible one. It was concluded that there are negligible disparities in bulk fluid flow behaviour between the solvers for the case studies examined, indicating that solver selection might be less consequential for certain aspects of oxygen lancing.

Apr 16, 2024

By Jing Zhan

The fibrous precursor can be obtained by coordination precipitation process, using oxalate, cobalt chloride and ammonia. The composition and morphology of fibrous precursor were characterized by XRD, IR, DTA/TGA and SEM analysis. The results show that XRD pattern and composition of the precursor with fibrous morphology precipitated at pH=9.0 were different from that of ß-CoC2O4?2H2O precipitated at pH=1.0. The mechanism on the thermal decomposition of fibrous precursor was addressed. The influences of various conditions in pyrolysis, including the temperature, time, atmosphere, and the morphology of the precursor, on the morphology, average size and specific surface area of the Co powders were investigated in detailed. At last, the final product, fibrous cobalt powders with diameter about 0.3~0.5µm in size and 40~60 in aspect ratio, were produced by thermal decomposition at 400~500? in the weak reducing atmosphere. The structure of pores in cobalt powders was capillary tube with open ports and the majority was mesoporous.

Jan 1, 2009

By E. P. McCurdy, William J. Tait, Allen E. Craig

The Circuitron herein described applies current from the classifier motor circuit and energy from the sound of grinding media to move an oscillating disc. The disc through a photoelectric cell controls the speed of the ore feeder and consequently the amount of ore delivered to the mill.

Jan 10, 1950

A rough simulated borehole has been developed for the installation and dynamic testing of rock bolts a the WASM Dynamic Test Facility. The rough simulated borehole is used for rock bolts that are sensitive to equipment installation technique or borehole geometry (particularly friction rock stabilisers and resin encapsulated bolts). An extensive axial test program has quantified a difference between the static and dynamic capacity (kN/m of embedment) for friction rock stabilisers once sliding starts. The 47mm split tube bolt has a 50% reduction in embedment capacity (but with significant variation) dissipating 2.7kJ/100mm of sliding per meter of embedment, and the Omega (inflatable) bolt had a 70% reduction in embedment capacity dissipating 6.2kJ/100mm of sliding per meter of embedment. The Omega bolt dynamic capacity remainder at least equivalent to the split tube bolt static capacity.

May 1, 2009

By K. Rushdi, B. E. Abulnaga

The conventional Froude number is blind to the presence of solids, their density and their concentration in a stream of slurry mixture such as tailings flowing in an open channel. This often leads to rough approximations of subcritical, critical and supercritical regimes, based on one phase flow Froude number, limiting subcritical to a value smaller than 0.8 and supercritical to values above 1.4, as proposed in the past by Green, Abulnaga and other authors. While acceptable for small flows, such approximations can be uneconomical for the larger flows encountered in some modern plants that treat up to half a million t/day. A review of concepts of a densimetric Froude number sheds some light on the effect of solids on stratification prior and subsequent to a hydraulic jump. While the approach is heavily borrowed from modern sedimentology, it provides a useful tool to designers of large launders or open channel tailings systems. These concepts are reviewed with some practical examples.

Jan 1, 2013

By Frank Schrader

J. DANA SPERR, Jerome, Ariz. (communication to the Secretary*).¬Very little accurate information has been published about this district. Most of the geological data appearing in the technical press are based on "careful observations" made from an auto stage and a casual glance through the U. S. Geological Survey Bulletins, No. 340 of 1908 or No. 397 of 1909, both by F. C. Schrader. Mr. Schrader's report is still the best publication on the district. A really careful study of this report will uncover only a very few statements which have since proven questionable. This is a remarkable record when it is considered that only a short time was spent by Mr. Schrader in the field and that there was very little development work done at that time. The mining world and especially Mohave County, Ariz., will feel a sense of gratitude to Mr. Schrader for revising his early report. on this

Jan 3, 1917

By P. C. Johnson, B. A. Stein

This paper describes a study of the effects of combined heat treatment and explosive loading on the mechanical properties of high-strength steels. nis program investigated two distinct areas: 1) the effect of shock waves, without gross irreversible defmmution, on a 3-Cr steel at various stages of heat treatment; and 2) the effect of rapid deformation (explosive forming) on H-11 and D6-AC steels in the metastable austenitic state. The mechanical properties of these steels were improved, in some cases markedly, as a result of these treatments. ,AUSFORMWG, which requires the plastic deformation of metastable austenite, is a process which can appreciably improve the properties of selected alloy stee1s.l,2 The Ausform process significantly increases the strength of these steels without decreasing their ductility. The properties at high temperatures are also improved through a change in the response of the steels to tempering. Although the mechanism by which ausforming alters the properties of these steels is not fully understood, it appears that the dislocation arrays produced by deformation of the metastable austenite influence the structure of the martensite on subsequent transformation. This, in turn, affects the strength, ductility, and tempering response of the martensite. This research used chemical explosives to deform steels at various stages in their heat treatment in order to improve the properties of these steels. The explosive energy is used in two ways; 1) high-pressure shock waves are propagated through the steel to produce extensive microscopic shear strain without causing a large irreversible change in shape, and 2) explosive energy is used to cause extensive macroscopic plastic strain in the metastable austenitic state (explosive forming). I) AUSFORMING WITH INTENSE SHOCK WAVES The steel used in this phase of the research was an alloy having a nominal composition 0.43 pct C, 3.0 pct Cr, 1.5 pct Ni, and 1.5 pct Si. The steel was subjected to intense shock waves in three conditions: 1) in the metastable austenitic state, 2) in the tempered mar tens itic state, and 3) in the tempered martensitic state after ausforming by conventional techniques. The specimens were in the form of disks 2.75 in. in diam and 5/16 in. thick. These were incorporated into a specimen assembly consisting of two disks pressed into a 5 by 5 by 1 in. block of stainless steel, Fig. 1. Spalling (or scabbing) is confined to the front disk. The specimen is protected from oxidation and decarburization by the surrounding metal. The temperature of the assembly is monitored by a thermocouple inserted into one side of the stainless steel block. The assembly is positioned over an oil reservoir which serves both as a means of catching the disks and as quenching medium for the disks shocked under ausforming conditions. Plane shock waves are introduced into the assembly by a metal driver plate impacting the top surface of the block. The driver plate is accelerated by a chemical explosive sheet supplied by E. I. du Pont de Nemours & Co. All the specimens were subjected to plane shock waves having a peak pressure of approximately 430 kbar. The pressure is that quoted by G. E. Dieter for the plane wave generator used in this work.' The driver plate used was 1/4 in. thick, so that the initial pulse was essentially a l/2-in.-wide square wave. The attenuation of the peak pressure during the subsequent 1/4 in. is estimated to be less than 5 pct. The shock front induces a temperature rise, a portion of which is irreversible. Rough estimates (+25 pct) of this temperature rise have been made for iron shocked at room temperature.4 For a 500-kbar shock wave, the temperature rise in the shock front is about 700°F, and is held for a time of the order of microseconds. The irreversible temperature rise, which remains after the shock wave passes, is about 450°F.4 The disks are quenched to room temperature within a few seconds of the shock treatment. It should be emphasized that the temperature rises given above are estimates for pure iron at room temperature, and are not necessarily true for the tests made in this work. The disks shocked at temperatures in the metastable austenitic range were austenitized in the stainless steel assembly in a furnace protected from the firing area. The assembly was removed from the furnace and placed over the recovery reservoir. The plane wave generator was then positioned and

Jan 1, 1963

By Luciana Vilarinho Ramos de Carvalho

Este trabalho tem como objetivo avaliar o efeito do nióbio e do vanádio no aço estrutural, conforme norma brasileira NBR 7007 AR 415, quando laminado a quente a diferentes temperaturas de reaquecimento, nos resultados de limite de escoamento, limite de resistência e alongamento. Os demais parâmetros de processo que influenciam as propriedades mecânicas dos aços como temperatura e taxa de deformação de cada passe, temperatura de acabamento e taxa de resfriamento foram controlados e considerados constantes. Os resultados do ensaio de tração mostraram que os limites de escoamento e resistência da corrida com vanádio foram bem superiores aos obtidos da corrida com nióbio. O alongamento, em contrapartida, foi reduzido na corrida com vanádio, mas acima do valor mínimo especificado pela norma. Além disso, na corrida com nióbio, foi observado aumento das tensões de escoamento e resistência com o aumento da temperatura de reaquecimento de tarugos. Esses resultados propiciam uma maior flexibilidade da usina em trabalhar com os dois tipos de liga dependendo das condições de mercado e operacionais.

Jul 30, 2018

By Russell Frith

For many years, underground rock mechanics and in particular, roadway/tunnel roof stability has been underpinned by the often unchallenged assumption that roof strength (as defined by the UCS) and stiffness (E) are key stability controls. This has logically led to the proliferation of laboratory testing of rock specimens and the development of indirect geophysical methods to gain estimates of these two rock parameters. Furthermore, many design methods are significantly focussed on replicating rock mass behaviour through either intact or failed constitutive models. Demonstrably the strength and stiffness of the host rock material is commonly used as one of the key indicators of excavation roof stability and it finds either direct or indirect use in just about every rock mass rating system in use today. In more recent times there has been a common move to consider and apply (even if only conceptually at the current time) structural engineering type principles (e.g. buckling) to coal mine roadway roof (and rib) stability. Similarly our knowledge of the in situ stress environment and its likely origins has improved significantly, largely through stress measurements and subsequent analysis. This paper combines knowledge in both of these fundamental areas through a deterministic model for roadway roof stability and in combination with field examples, reaches the almost certainly controversial conclusion that UCS and E are commonly irrelevant, albeit that the former may provide an indication of other relevant geotechnical parameters (e.g. bedding cohesion). As with all hypotheses or rules, there are naturally exceptions and in this case, the most obvious is the tailgate of the longwall panel (with adjacent goaf). Due to the significant change in the strata loading environment of a longwall tailgate as compared to first workings for example, the stability equation materially changes so that UCS and E become critical controls. The point of the paper is to present a different perspective on a traditional mining problem and to challenge geotechnical professionals to keep thinking ?outside of the square? in the never-ending endeavour to improve our understanding of the engineering problems we regularly face. Such an understanding impacts upon such issues as geotechnical data collection from borecore, support hardware requirements and design capabilities. Therefore making the assumption that our understanding is always fundamentally correct could in fact be limiting the development of new and improved engineering in the future.

Jan 1, 2006

By K. Olsen

As aluminum alloy usage in automobiles grows, there are increasing demands on recycling processes and facilities to deal with mixed alloy automotive aluminum scrap. These processes and facilities strive to produce near virgin aluminum stock, which can be relatively costly and difficult. One alternative is to use physical processing methods to upgrade the scrap properties instead of chemically refining the scrap. The Impulse Atomization Process (LAP, patent pending) is a new process for making metallic and ceramic powders. It can produce fine homogeneous microstructures in scrap aluminum alloys due to high undercooling and rapid solidification. The particles have a very narrow size distribution and are in a convenient form for consolidation. This paper compares and contrasts the microstructural features of Impulse Atomized. and quenched Impulse Atomized powders,' for both AL6061 and a scrap aluminum alloy composition.

Jan 1, 1995

By W. K. Collins

Engineered Scavenger Compounds (ESCs), developed by the U.S. Bureau of Mines, are a novel class of compounds that can selectively recover a desired element from a solid or molten alloy. Lithium titanate (Li2Ti3O7 or L'20-3T'02) is being used as an ESC to recover lithium (Li) from Aluminum-Lithium (Al-Li) alloys. X-ray diffraction measurements have shown that lithium titanate undergoes a phase change from an orthorhombic structure to a hexagonal structure. This change is due to the incorporation of Li in the matrix of the material and the effect of temperature. Although both are metastable, the hexagonal phase that forms during the scavenging of Li from Al-Li alloys appears to be the more stable phase. Recovering Li from the ESC by electrodeposition does not cause the structure to revert to the orthorhombic phase. Both the orthorhombic and the hexagonal structures of Li2Ti3O7 have similar scavenging capacities for Li. This paper proposes a new mechanism for the phase transformation.

Jan 1, 1993

By W. D. Riley

Engineered Scavenger Compounds (ESCs), developed by the U. S. Bureau of Mines I are a novel class of compounds that can selectively recover a desired element from 'a solid or molten alloy. Lithium titanate (Li2Tip7 or Li20' 3TiO.) is being used as an ESC to recover lithium (Li) from Aluminum-Lithium (AI-Li) alloys. X-ray diffraction measurements have shown that lithium titanate undergoes a phase change from an orthorhombic structure to a hexagonal structure. This change is due to the incorporation of Li in the matrix of the material and the effect of temperature. Although both of the structures are metastable, the hexagonal phase that forms during the scavenging of Li from AI-Li alloys appears to be the more stable phase. Recovering Li from the ESC by electtodeposition does not cause the structure to revert to the orthorhombic phase. Both the orthorhombic and the hexagonal structures of Li.Til07 have similar scavenging capacities for Li. This paper proposes a new mechanism for the phase transformation.

Jan 1, 1991

By K. J. Liles

To encourage the development and conservation of the Nation's ceramic raw materials, the Bureau of Mines, U.S. Department of the Interior, under an agreement with the Georgia Department of Natural Resources, evaluated samples from a clay resource located in Clay County, Ga., for use as a raw material for lightweight aggregate. The physical properties of clay samples, taken from 5-foot increments of drill cores from 11 holes, were determined. Raw materials were plasticized and extruded to produce 1/2-inch by 1-inch pieces and fired in a rotary kiln to produce lightweight aggregate samples. The resulting expanded material had excellent loose pour weights ranging from 30 to 37 lb/cu ft. The expanded test materials were crushed, sized, and used as aggregate to form concrete cylinders. The unit weight and compressive strength of the cylinders averaged 106 lb/cu ft and 3,350 lb/sq in, respectively; these values meet American Society for Testing and Materials specifications for structural concrete. The clay from the drill cores was also used to make test bars that were evaluated for building brick.

Jan 1, 1980

By Waldemar Lindgren

THE following pages present data accepted by many geochemists and geologists regarding the succession of minerals and the temperatures of formation in ore deposits affiliated with igneous rocks. They also present the individual views of the author on the composition of the solutions that were active and on the mode of deposition. He does not regard these views as speculations or hypotheses but as forming a well motivated and consistent theory. It is not certain, however, that all investigators will subscribe to them.

Jan 1, 1936

CONTENTS: Broken Hill The mixing stations.Operating and mixing apparatus.Pulp distribution.Stope preparation.Filling procedure.Consolidation of old fill.Drainage:Pulp density tests. Life of sand pipe lines.Results.Advantages and disadvantages.Conclusion and acknowledgments.General remarks on South Limited.Mining methods.History of stope filling in Broken Hill.Need for a new and better filling method and transport system.Initial experiments with hydraulic stowing.Source of the sand.Water Supply.Signalling system.GENERAL REMARKS ON BROKEN HILL SOUTH LIMITEDThe South Mine, property of Broken Hill South Limited, is situated at Broken Hill, N.S.W., Australia, towards the southern end of the main lode.The leases (M.L's 7 and 8)' cover a length of 2,400 feet along the lode outcrop and the workings extend, at this date, to a depth of 1,940 feet below the collar of the original main shaft and to 825 feet below sea level.Mining operations have been continuous for about 58 years and during this period nearly 12.5 million tons of ore have been mined. The monthly tonnage extracted approximates 30,000 tons in normal times.The ore is a mixed sulphide containing galena and marmatite; the gangue minerals are principally calcite, rhodonite, quartz and garnet.A typical assay for a monthly period is 14·40/0 Pb., 5·6 ozs. Ag., and 11· 60/0 Zn. The whole of the ore is concentrated on the property by combined gravity and flotation methods. The lead and 'zinc concentrates produced are railed to other centres for the extraction of the contained metals.MINING METHODSMining practice throughout the field varies only in minor details. The ore-bodies forming the Broken Hill Lode lie within complex folds arranged along a shear and vary in size and mineralogical associations, but all the mines have similar types. Some of the ore-bodies have weak walls, but the chief difficulty in mining is caused by "heads" and "flaws" in the ore.Besides these local weak areas there are ground movements-referred to later-of varying magnitude extending throughout the central portion of the lode where the large ore-bodies, several hundred feet wide, approached the surface.

Jan 1, 1944