Search Documents

By Supachai Surapunl

The distribution behavior of VA minor elements (As, Sb and Bi) in the smelting stage of the Mitsubishi process were evaluated thermodynamically based on thermodynamic data and operating data. The fractional distributions between the gas, slag and matte phases considered as the degree of vapor saturation of l.0 are as follows: 53.8, 27.2 and 19% for As, 23.6, 56.6 and 19.8% for Sb, and 91.3, l.1 and 7.6% for Bi, respectively. Arsenic is mostly distributed to the gas and slag phases. It is effectively eliminated by volatilizing and slagging. Antimony is mainly in the slag phase, which is suitably removed by slagging. Bismuth is easily vaporized to gas phase. The degree of vapor saturation has a large effect on the distribution behaviors of the three elements between the three phases. The amount of a minor element in the charge has an effect on the distribution of As but no effect on the distributions of Sb and Bi. Increasing matte grade and temperature results in the change of distributions for As and Sb, significantly. The change in the distribution ratio between slag and matte phases also considerably affects the distributions of As and Sb. The distribution behavior of Bi is not significantly changed by the change in matte grade, temperature and distribution ratio.

Jan 1, 2003

By R. F. Robertson

"Adsorption isotherms of hexyl mercaptan vapour on synthetic sphalerite, zinc sulphide and zinc oxide were de-termined with a gravimetric McBain-Baker micro balance incorporated in the B.E.T. apparatus. Isotherms are given for hexyl mercaptan on synthetic sphalerite at 25°C, 0.5°C and 50°C; on zinc sulphide at 25°C and 1.5°C; and on zinc oxide at 25°C. All these isotherms are sigmoidal, with a definite change in slope at or close to the mono-layer. The amount of mercaptan adsorbed below the monolayer increases almost linearly with relative pressure to P/P0 = 0.8.Above this value, the amount adsorbed increases very rapidly with relative pressure. Hysteresis loops appear in the isotherms for all adsorption-desorption cycles. These loops are completely reversible. It is not possible to desorb the mercaptan monolayer from any of the adsorbents, even at elevated temperatures."

Jan 1, 1966

By Chris Uys, Johan Labuschagne

Sishen Iron Ore Mine, located in the Northern Cape, is an open cast mine excavating approximately 100 million tons rock to produce 25 million tons of high grade haematite ore per annum. The size of the pit is approximately 12 km ‘1.5 km ‘150 metres. The final depth is planned to be around 350 metres. It is hard rock mining operation employing the conventional truck and shovel method. Mining benches are twelve and a half metres in height and are divided into blasting blocks, each consisting of approximately 300 000 tons of material.

Jan 1, 1997

By James Terry Duce

The symposium on production for the year 1940 contains few papers on the foreign situation. It is probable that the foreign part of next year's symposium will be even shorter. This is due to rigid censorship in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even more true than in the last war, owing to greater mechanization of armies. 'It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable frod data available to the author, please inserty; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In sucli cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved') and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1941

By James Terry Duce

The symposium on production for the year 1941 contains few papers on the foreign situation. Rigid censorship prevails in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even truer than in the last war, owing to greater mechanization of armies. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to AutHORs In order to facilitate interpretation of the data in this chapter, we print the fol-lowing excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir.. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1942

By Basil B. Zavoico

The symposium on production for the year 1942 contains no papers on the foreign situation except those on Argentina and Mexico. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts From Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not determinable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a Rope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone.

Jan 1, 1943

By R-H Yoon

The MicrocelTM column flotation technology has been developed based on the fundamental understanding that the first-order flotation rate constant increases approximately as the inverse cube of bubble size. In this technology, bubbles in the range of 100-400 pm are generated by pumping aerated slurry through an in-line static mixer. The high-shear agitation provided by the in-line mixer produces small air bubbles without requiring large frother additions. This column has been tested successfully for processing a variety of non-metallic minerals including kaolin clay, graphite, phosphate, and feldspar.

Jan 1, 1993

Traction of mining vehicles is well understood for a variety of unfrozen road surfaces, allowing optimal design of mine access and haulage roads. However, no such characterizations exist for the frozen or partially frozen surfaces typically encountered in Northern regions. Recent work by U. S. Army researchers suggests methods for characterizing roadway traction for any vehicle on the basis of test measurements made with a standard test vehicle. Such a test vehicle was designed, and several sets of test data were recorded at the onset of winter in Fairbanks, Alaska. This work suggests methods for future research and possibilities for the use of such research in designing drive systems, tires, and mine roads for Arctic and sub-Arctic mines.

Jan 1, 1995

By Leo J. Vogel, E. D. Hummer

INTRODUCTION by E. D. HUMMER An efficient refuse-disposal system is a necessary part of the modem cleaning plant. The large-scale refuse system and disposal area, engineered for the lifetime of the plant, has become more important due to the greater tonnages of refuse produced from increased quantities of mechanically mined and prepared coal. Laws and increased government regulations have affected the design and operation of disposal systems. THE EFFECT OF MINE AND PLANT OPERATION Refuse disposal starts at the mining face. The mining system, the type of roof support, the machinery used, and the degree of discipline at the face contributes to the amount and type of refuse that must be removed through the disposal system. Economies gained through modification of the mining system or mining machinery may be partially offset by increased dilution of the mined coal with impurities from associated rock formations. In some cases the change in the mining system and equipment has reduced the dilution. In all cases the ratio of impurities that must be removed from the raw-coal feed to the plant not only affects the maintenance and operating costs of the plant, but greatly affects the design of the refuse disposal system. The design of a mine and plant should include the location and the estimated capacity of the disposal areas for the life of the property or plant. Complete evaluation of the disposal system and an estimate of its annual cost of operation over the life of the property or plant should be incorporated in the plant and mine evaluation. Plant design should be as simple as possible, consistent with the efficient production of clean coal. Material transfer points, crushing, screening and pumping operations should be kept to a minimum to reduce degradation and the subsequent increased difficulty and cost of refuse removal. The maintenance of good process control by operating management will result in a minimum of misplaced material in both refuse and clean coal. Reduction of misplaced float material in the plant refuse is an important factor in preventing combustion in the refuse storage pile. THE REFUSE DISPOSAL AREA Combustion in refuse piles occurs when air enters the pile in sufficient quantity to support oxidation. At certain rates of air in-filtration, the heat produced by the oxidation process is not dissipated and temperature rises.

Jan 1, 1968

By Klaus Stoss, Bernd Braun

The sinking and lining of a large mine shaft with 8.0 m i.d. and 1,133 m total depth is described in detail. The ground freezing method was applied to safely sink the shaft through unstable, waterbearing strata. Following a brief introduction to the geological and hydrological conditions and the owner's shaft requirements, is the general technical concept to sink and line the shaft. Particular emphasis is put on the lining system which has to provide stability and absolute watertightness for the lifetime of the shaft, even though mining takes place in its immediate proximity. Machinery and equipment used to execute the work are mentioned and commented. Furthermore, the excavation and lining of the large filling stations using rock anchors and shotcrete are described. Details on performance rates are given.

Jan 1, 1983

By K. Hambrice, E. Fauveau

"When it comes to measuring the level of bulk solids, liquids, and everything in between, guided-wave radar technology now offers more level-detection capabilities than ever before. For an ever-widening range of previously hard-tomeasure products such as molten sulphur, liquid ammonia and petrochemicals, guided-wave radar transmitters provide accurate level measurements even under harsh chemical environments, wide variations in operating temperatures and pressures, and low dielectric constants.Great strides have been achieved in making these units easier to configure to a variety of process applications coupled with the simplicity of integrating these devices with most digital communication protocols. These improvements come as welcome relief to process engineers within an expanded range of level applications across several different industries that seek solutions to measuring the contents of tanks, silos, hoppers, bins, mixing basins, and vessels.Because radar transmitters have no moving parts, radar has already established a dominant niche in level measuring that quickly distances itself from mechanical means, which do not hold up as well in dirty service. Radar achieves its nonmechanical level detection capability by measuring the time of flight of the transmitted signal.Known more accurately as time domain reflectometry (TDR), the process involves sending microwave energy down into a vessel. When the pulse of radar energy reaches the product (indicated by a change in impedance), part of the pulse is reflected back toward the transmitter.A receiver measures the exact duration of time between the transmitted and reflected signal — the “time of flight.” The device analyzes this time and ultimately displays the level of the product as a distance in feet, metres, or other engineering units."

Jan 1, 2003

By J. B. Hess, C. S. Barrett

Single crystal rods of cadmium collapse under uniaxial compression into peculiar kinks if the (0001) glide plane is nearly parallel to the axis of compression. In his report first describing this behavior, Orowan1 proposed that these "kink bands" do not develop entirely by ordinary gliding and twinning but by a special mechanism in which glide lamellae of uniform thickness snap abruptly to a tilted position that permits lattice continuity across the glide planes. He concluded that a portion of each boundary of a kink band consists of a plane (non-crystallo-graphic) which bisects the angle between the glide planes on the two sides of it, and along which the bending and the dislocations are concentrated. The data presented by Orowan seemed to us to be insuffcient to conclude that a wholly new mechanism of deformation was responsible for the kinks. Therefore, we have investigated zinc, which is hexagonal close-packed and has an axial ratio near to cadmium, to see whether similar bands are produced, and whether the ordinary mechanisms of glide, bend-gliding, twinning, and the formation of deformation bands can account for its mode of deformation. We find that kinks form profusely in zinc as shown in Fig 1. The structure of these kinks, reported below, seems to require no new mechanism for their explanation, but indicates that kink bands are a special form of deformation bands and develop gradually, solely from basal glide. A theory covering the formation and structure of the bands is presented in detail because it is seldom possible to study deformation bands under such simple conditions, yet many principles applying to these kinks should also apply to deformation bands in general. Experimental Procedures Single crystal rods of 2-3 mm diam and 10-15 cm length were grown by the Brideman technique from swaged wire of Horsehead Special zinc in un-coated pyrex tubes. Orientations of the rods were determined with an optical goniometer after cleaving the rods at liquid air temperature. Crystals of desired orientations were then selected and used as "seeds" to grow additional crystals approximately 4 ft in length from which all specimens were cut. The wires were compressed in two ways: in a simple hydraulic handpress —a "soft" machine—and in a Riehle hydraulic testing machine modified to produce very "stiff" action by the simple expedient of inserting lengths of steel bars at the sides of the zinc crystals between the compression plates. For metallographic examination, the specimens were mounted in sealing wax. Hand polishing was employed, with no grits coarser than No. 1 paper; following the abrasives about 0.025 in. was removed by an etch-polishing reagent.* Final etching to reveal ori-

Jan 1, 1950

By M. J. Preim

Two case histories are presented on the evaluation of static bearing capacity of piles driven in soils that exhibit time dependent strength changes. Under consideration are a steel and a concrete pile driven into soils generally consisting of silty and clayey fine sand. Pile dynamic measurements and analyses were performed on both piles during initial installation, and also during restrike one week later. This information was used to predict each pile's long term capacity (defined as 14 days after initial drive), which was then compared to that measured with a static load test. Agreement between predicted and measured capacities were remarkably good, with an average error of only 4.5 percent. Two weeks after driving, total pile capacities were three times those at the end of drive. If only the skin friction was considered, however, it increased by an average factor of 16. The increase in pile capacity was determined to be linear over the time period considered.

Jan 1, 1989

By C. D. Johnson

Exploration work in 1932 in the Rocky Mountain region, which includes the states of Montana, Wyoming, Utah, Colorado and New Mexico, resulted in the discovery of one new oil field, Cut Bank in Glacier County, Montana; one new gas field, Craig in Moffat County, Colorado; and the definite outlining of a second gas field, Piceance Creek in Rio Blanco County, Colorado, in which there had been drilled but one small gas well prior to 1932. During the year, 95 producing oil or gas wells were completed, giving new initial production amounting to 188,000,000 cu. ft. of gas and 176,420 bbl. of oil per day for the region. By far the largest part of this new production of both oil and gas was developed in southeastern New Mexico, mainly the Hobbs field. However, the Dry Creek field of Carbon County, Montana, contributed over 5000 bbl. of; new oil production. Sixty-two wells were abandoned during the year but of this number only 10 promising structures were nonproductive. The remaining 52 wells had little to recommend their drilling from a structural or strati-graphical standpoint. Eighty-eight wells were suspended in the region' during 1932 before the tests had reached their individual objective horizons. Many of these suspensions were due to financial difficulties and it is possible that several of the operations may be resumed at a later date. At the close of the year, 54 wells were actively drilling, 54 were shut down and there were 20 rigs and locations in the five Rocky Mountain states. The accompanying table gives details of drilling and production.

Jan 1, 1933

By P. V. Roundy

PUBLIC lands in Florida were first withdrawn from entry by President Taft on July 2, 1910, as a conservation measure because of their possible phosphate content. The reserve thus established was subsequently modified by further withdrawals and by restorations, so that on Jan. 1, 1934,' it contained 66,796 acres, of which only a small part had been defi-nitely classified. The reserved land was in scattered parcels, ranging from less than 40 acres to 320 or more, distributed in many counties. For administrative purposes and for final disposal of any of the numerous parcels, mineral classification of the land is legally necessary. In 1934 and 1935 the United States Geological Survey, under two successive grants from the Public Works Administration, prospected some 83 tracts of these lands in Polk County, comprising in all about 3300 acres, and six tracts comprising 240 acres in Citrus and Marion Counties. The tracts in Polk County were all in the so-called land-pebble field and the others in the hard-rock field. The Survey field party was under the direction of P. V. Roundy, from whose unpublished report the material in this paper is largely taken. The foreman of the prospecting crew was J. H. Wingate of Zephyrhills, Fla. The individual tracts were identified through the cooperation of the General Land Office, by transitman Hugh B. Crawford. This prospecting work fitted well the classification adopted for Public Works projects in general: it could not he done on any considerable scale under the Survey's usual appropriations; it gave employment to unem-ployed labor; and it may be expected ultimately to repay the Government in royalties more than the cost of the exploration.

Jan 1, 1937

By P M. Hancock, Associates

Lacustrine sediments, hydrothermal explosion breccias and spring precipitates deposited 5200 - 1800 years BP as a result of geothermal activity at Lake Rotokaua, contain New Zealand's largest known sulphur reserves. Current drill indicated reserves are 2 600 000 tonnes of elemental sulphur, assuming a ten per cent (dry basis) cut-off, contained in some 17 000 000 tonnes of ore with an average grade of 214.0 per cent (dry basis) sulphur. Additional inferred ore containing 500 000 - 900 000 tonnes of sulphur has yet to be prospected by drilling. Geological factors will be important in exploitation of the deposit, particularly the extent and disposition of the orebody, sulphur grades and distribution, physical characteristics of the ore, permeability and stability of the overburden and the nature and extent of geothermal activity in the area. Trials to date indicate that Frasch mining and possibly opencutting are unlikely to be successful mining methods. Further mining feasibility studies will be required to ascertain the most likely mining system for the deposit.

Jan 1, 1984

By P. G. Flood

A simplified conceptual model shows how the arc flank to arc fringe areas adjacent to ignimbritic centres form a prospective zone for natural zeolites. Large alkaline lakes that serve as the repository of voluminous ash-fall tuffaceous material provide the ideal chemical setting for pervasive alteration of silicic glass to zeolites. The unusually old age of the Escott deposit demonstrates that any silicic volcanic province that contains low-temperature, unmetamorphosed sequences is a potential zeolite exploration target and that age should not be used as a criterion to exclude potential areas. It has also been demonstrated that heulandite and mordenite, formed by diagenetic alteration of silicic glass, do not always change to analcite and albite through the ageing process

Jan 1, 1991

By Nobuhiro Ishikawa

The in-situ observation of the effect of impurities on the reduction process of iron oxides by C in TEM was carried out. A few wt% of CaO or AbO, was used as impurities in FeO was prepared. Some precipitates grew into the C layer expect for using 3.0wtCa. The reaction between FeO and carbon was much different from using pure FeO at about 800-1 lOOK. The rate of reaction became much slower including Ca and almost no reaction was happened with the concentration of CaO up to 3.0wt%. On the contrary, AbO, had ahuost no effect on the reaction. The results indicated that Ca suppressed the reaction and the effect of Al was much less. The precipitates which grew into C layer accompanied almost no Ca and AI. Only Fe was detected in the precipitates.

Jan 1, 2008

The compliance sampling method for coal mine dust in the United States has not changed appreciably in the last 30 years. A call for more frequent sampling with immediately available results is leading to new instruments that may supplement or replace the existing sampler. This report discusses two such instruments that provide immediate results of dust levels. The first, called the Respirable Dust Dosimeter (RDD), is designed to supplement the existing U. S. cyclone compliance sampling method. It uses the pressure drop across a filter to provide an inexpensive screening type of measurement. The RDD has been tested in the laboratory and a limited number of coal mines. Side by side testing has compared the RDD performance with personal coal mine samplers in triplicate area sample measurements. Results show that the differential pressure of specific filtration media can be an effective surrogate for respirable mass. Data show that there is a dependence on coal type and an effect of relative humidity. There also appear to be two distinct responses related to coal type. For specific coals the coefficients of determination, R2, are better than 0.9. For general use the detector tube, using laboratory generated calibration curves, can be used to estimate respirable dust levels. However, a calibration to a specific coal type may substantially improve the accuracy. Another sampler in development is called the Personal Dust Monitor (PDM). Designed to give compliance quality accuracy, the PDM uses the frequency change of a vibrating element to measure dust and give immediate feedback of results. Results of laboratory comparison of the prototype PDM sampler to personal gravimetric samplers indicate R2 values of better than 0.99 for three different coal types. Work is in progress to package the components into a person-wearable unit combined with a cap lamp system with a total projected weight of less than 1.4 kg (3 lbs).

High Pressure Grinding Rolls (HPGR) are said to be a good option in new grinding circuits. Due to their low energy consumption compared to other grinding systems such as SAG milling, there is a strong incentive to check their behaviour for certain ore types. With rising energy prices the operation will become even more beneficial in future. As published in the past, the HPGR is claimed to increase the liberation of the valuable mineral component within an ore. An investigation at the research centre of Polysius was conducted to substantiate the liberation behaviour in finish grinding operations. A pilot scale HPGR test unit (POLYCOM MAGRO) with a roll diameter of 950 mm and processing capacity of 80 t/h was used. Grinding tests were completed with a screen and a two stage drying air separation process (SEPOL). Analysis included standard screen analysis, fractional XRF and modern MLA technology. A technique was developed to oppose the amount of produced slimes (resuming bad flotation) against the positive effect of producing high mass fraction at flotation-easy sizes. The paper shows how effective the use of a dry grinding separation could be in terms of production of mass of liberated metal.

Jan 1, 2012