Search Documents

By Anna Franzkowiak, Dean Gregurek, Alfred Spanring, Angelika Ressler

In order to determine the most suitable refractory products and improve the lining lifetime for the diverse furnaces used in the nonferrous metal industry, corrosion tests are performed at RHI’s Technology Center. The practical facilities include the cup test, induction furnace, rotary kiln, and drip slag test described in this paper, which enable a comprehensive understanding of the chemo-thermal brick wear on a pilot scale. The corrosion trials are performed with actual slags generated during operations at a customer’s plant. To determine the highest influencing wear parameter, every single test is combined with a detailed mineralogical investigation and thermochemical calculations performed using FactSage. Based on the results, tailored refractory solutions for the nonferrous metal industry can be provided in combination with trials conducted at the customer’s site.

Jan 1, 2014

By C. Altstetter

THE work herein reported is restricted to the carbides which occur in quenched and tempered AISI 43XX steels with carbon contents up to 0.40 pct and silicon additions of up to 3 pct. In view of the instability and extremely small size of the carbides formed at low tempering temperatures, the technique for successfully preparing specimens for X-ray diffraction will be outlined. The alloys listed in Table I were obtained through the courtesy of the United States Steel Corp. in the form of 1/2-in. rounds forged from 100 lb. induction furnace heats (except for 4337 which was a commercial heat). The stock was normalized and then swaged and drawn to 15 mil wire with anneals at 1200F between passes. The wire was austenitized for 45 min in evacuated vycor capsules and quenched into iced brine with simultaneous smashing of the capsule. Tempering was done in air with a water quench after tempering. The carbides were extracted in a simple cell using a solution of 1M KC1 and 0.5 pct citric acid with an initial current density of 0.1 amp per sq cm. One end of a short length of wire was immersed in the solution, and the current at constant voltage was noted as a function of time. After about an hour the current dropped sharply because of the decrease in specimen cross-section. At this point it was found that the dissolution could be stopped and that the very fine wire which then resulted was just large enough to permit handling of the extracted precipitate still clinging to it, yet so small that it diffracted and absorbed only a negligible amount of the X-radiation. This rod of residue with a convenient handle of undissolved wire was rinsed in distilled water. alcohol, and acetone. Then it was dipped in a thin solution of cellulose-acetate cement and dried in vacuum. The resulting specimen was straight, uniform in density, easily handled, but most important, was completely sealed and never exposed to air. Furthermore, the residue had never been subjected to strong acids or rough handling such as in the extraction-replica technique or in the complete extraction to a powdered residue. It was found that improperly coated specimens were pyrophoric, turning to oxide with a dull red glow as they were exposed to air and yielding patterns of Fe2O3 and Fe3O4. The steels containing 3 pct Si were especially difficult to prepare for this reason. The specimens were put in a 57 mm Straumanis camera with double pinholes or slits and irradiated with filtered-chromium radiation. Readable patterns were obtained in less than an hour. A preliminary finding of some note was that for both tempered and as-quenched specimens of steels 4337 and 4337 (1.5 Si). M23C6 patterns were found along with the patterns of other constituents of the residues. This result was somewhat surprising in that previous investigators had reported that this carbide did not appear in a 0.38 pct C, 0.48 pct Mo steel1 or in chromium steels of less than about 10 pct Cr.2 Although the total amount of carbide-forming alloying elements is less than 2 pct, due to their mutual interaction and the action of the plastic deformation in promoting equilibrium, this carbide was able to form even in the steel containing 1.5 pct Si. M23C6 was not detected in the 4337 (3.0 Si) steel and the lower-carbon steels were not investigated in this condition. It is very likely then that the steels studied herein underwent a fourth stage of tempering during the anneals at 1200°F. This result has significance in that even a small amount of undissolved M23C6 in a low-carbon, low-alloy steel would exert a large effect on its hardenability. Its presence would also influence the mechanical properties by decreasing the carbon content of the matrix. Annealing in vacuum for 1 to 4 hr in the austenite field removed all traces of MZ3C+ The results on carbide precipitation during tempering, summarized in Table I, are in agreement with those of Klingler et al.3 for the higher carbon steels. For the AISI 4337 steels it is noteworthy that in the steels with added silicon the E carbide persists to longer times and higher temperatures and that silicon delays the formation of cementite. The results for the lowzr-carbon steels parallel those of the higher-carbon grade. The appearance of E carbide in the AISI 4315 is significant. There is considerable disagreem-nt in the literature as to whether this carbide forms in the tempering of steels containing less than about 0.2 pct C. Following the detection of E carbide in a 0.18 pct C plain-carbon steel,4 its occurrence in a steel containing chromium and molybdenum should be expected. The fact that the low-carbon steels have the same carbide-precipitation sequence as the high-carbon steels has bearing on the larger problem of the exact tempering reactions in all steels. Following the suggestion of Roberts et al.,' the first stage has been generally assumed to result in a metastable equilibrium of c carbide and martensite of about 0.25 pct C. From this it was concluded that a steel having less than 0.25 pct C should then be under-saturated with respect to c carbide and should not precipitate this carbide upon tempering. In view of the experimental findings of c carbide in steels hav-

Jan 1, 1962

By C. W. Spencer, F. G. Hochgraf, R. F. Cheney

Columnar grained specimens of nickel, containing 0.25 pct Si and 0.22 pct Mn, have been exposed to liquid bismuth in the temperature range 670° to 1050°C. Under isothermal conditions the liquid penetration rate is constant. The activation energy for the process is 22,000 cal per g-atom. Small amounts of plastic deformation, introduced into specimens prior to exposure, increase the penetration rate. The slou. step in liquid film penetration is associated with a reaction which occurs at or near the leading edge of the film. Either transfer of nickel across the liquid-solid inteqace or diffusion in the grain boundary ahead of the liquid film is suggested. Aliquid metal, if brought into contact with the surface of an unstrained solid metal, will usually penetrate to some extent into the grain boundaries of the solid. Under isothermal conditions the extent of penetration after any particular time of exposure is related to the relative magnitudes of the interfacial tensions concerned.1,2 If the liquid-solid interfacial tension is less than one-half the grain boundary tension the liquid may penetrate at a relatively rapid rate for an indefinite distance into the grain boundary surfaces. If the liquid-solid interfacial tension is greater than one-half the grain boundary energy, liquid penetration occurs at a continually decreasing rate so that after the liquid has penetrated to a relatively short distance below the surface the process essentially ceases.3 Many observations of a qualitative nature concerning inter crystalline attack by liquid metals have been reported, for example, liquid bismuth upon copper,' liquid mercury upon brass,4 and liquid mercury upon nickel.' Scheil and Schessl determined the rate of penetration of liquid bismuth into the grain boundaries of hot rolled copper rod? At constant temperature, penetration rate was found to be independent of the depth penetrated, the rate in- creasing with increasing temperature corresponding to an activation energy of 20,000 cal per g-atom for the process. It was suggested that at lower temperatures the liquid travelled mainly along lines of three grain intersections while at temperatures greater than 1000°C essentially all grain boundary surfaces were covered. Recently, in a study of copper bicrystals having a common [loo] axis it was found that at 649°C bismuth penetrated 22, 25, and 63 deg boundaries while it did not penetrate 2, 12, 15, and 72 deg boundaries.' Elbaum reported that liquid gallium penetrates aluminum grain boundaries to a depth of 0.6 cm after 11 hr at 27°c.8 Assuming that the rate controlling step in the process was diffusion down the liquid film to the specimen surface, a diffusion coefficient of 10-5 cm2 per sec was calculated. This paper reports a study of the penetration of bismuth-nickel liquids into the grain boundaries of a nickel alloy, containing 0.25 pct Si and 0.22 pct Mn as principal alloying elements. The phase diagram

Jan 1, 1962

By George S. Koch

A statistical analysis of silver assay data from rotary-drill-hole cut-tings and diamond-drill-hole cores from the Round Mountain prospect, Custer County, Colo., demonstrates several useful methods for estimating grades and tonnages of ore from the drilling of wide-spaced holes in disseminated deposits of precious metals. A new method of are appraisal is introduced which estimates grade and tonnage of are by calculating convex hulls (smallest convex polygons) for sample points with assay values above specified cutoff grades. Analyses of variance compare the consistency of data from rotary-and diamond-drill holes, from rotary-drill holes sampled at 2-and 4-foot intervals, from two methods of sample preparation, and from atomic-absorption and fire assaying. Evidently, data from the two types of drill holes, from holes sampled at the two intervals, and from different methods of preparation are in agreement. Atomic-absorption silver values are consistently lower than fire-assay silver values.

Jan 1, 1971

By AIME AIME

OUT of the fabulous iron ranges of Michigan?s Upper Peninsula since Pearl Harbor have come go to the steel mills to become tanks, guns, ships, and other weapons for a United Nations' victory. But the contributions to the war effort, as far as Michigan's iron country is concerned, do not stop there. The same men who mine iron ore deep inside the earth also are "mining" on top of the ground, gleaning a harvest of scrap iron and steel that is writing a big chapter in the War Production Board's salvage program. At virtually every mine over an area of a hundred square miles, everyone from the top mine official and straw boss to the man in the dippings is scrap conscious. They know the importance of the ore they mine but they are equally familiar with the importance of iron and steel scrap in war production. The successful job they are doing in salvage is a tribute to the entire Upper Michigan mining industry and to the man who marshaled them into action-John M. Bush, chief of the land department for the Cleveland- Cliffs Iron Co. at Negaunee, and for ten years an A.I.M.E. member. Also, this job should be an inspiration to 611 mining. metallurgical, and petroleum communities as to the latent possibilities of organized scrap recovery.

Jan 1, 1943

By George J. Young

(Cleveland Meeting, October, 1912.) I. GENERAL. THE recurrence of mine-fires in Nevada during the past decade is not only a matter of interest, but also one of considerable concern to engineers and mine-managers. The more important fires may he enumerated as follows: Forman Shaft fire., Gold Hill, April 21, 1903 ; shaft-house, machinery, and shaft, destroyed; loss estimated at $50,000.; Cause Unknown. Union Shaft fire, Virginia City, July 14, 1904; shaft-house, machinery, and shaft in part destroyed; loss estimated it $100,000; cause of fire stated as the careless throwing of a match in the rope-house. Sutro Tunnel fire, Virginia City, Jan. 27, 1909 ; 700 ft. of tunnel-timbering destroyed, and direct damage of $10,000; cause ' probably electric wires." Belcher Shaft fire, Gold Hill, Aug. 9, 1910; shaft-house destroyed, machinery ruined, and upper part of shaft damaged; damage, $25,000; no cause given. Belmont Mine fire, Tonopah, Feb. 23, 1911; fire started in winze ; 17 men killed. Giroux Mine fire, Kimberly, Aug. 23, 1911 ; fire originated iii shaft-station from unknown cause; 7 men killed, and $34,¬521 damage caused. (NOTE 1.-On June 11, 1912, some time after the present paper was written, a fire broke out in the pump-room on the 2475 station of the Ward shaft, Virginia City. This fire was caused by the short-circuiting and exploding of the starting-switch on No. 5 pump. The oil in the switch was scattered about and set fire to the timbers and laming of the pump-room. The pump-roan in charge notified the surface, and the * Professor of Mining and Metallurgy, Mackay School of Mines.

Oct 1, 1912

By R. F. Holub, E. Franco, T. B. Borak, K. J. Schiager

INTRODUCTION According to a recent analysis by Schiager et al.(1981), inhalation of radon daughters continues to contribute the largest risk from exposure to radioactive materials in underground uranium mines. The American National Standards Institute (1973) has published a concensus standard for radiation protection in uranium mines. According to this standard, a monitoring system for radon daughters must be capable of measuring the annual accumulated exposure in working level months within an uncertainty interval of 50% at the 95% confidence level. To satisfy this criterion, uranium mining companies in the USA have adopted a procedure consisting of single or periodic measurements of the air concentration of radon daughters. All of the measurement methods sample a known volume of air through a filter. After a specified delay interval, the filter is analyzed for radioactivity. The exposure rate from total airborne potential alpha energy in units of working level (WL) is estimated from the measured activity on the filter. For control purposes, this measurement establishes whether or not a work area is safe for occupancy by miners. For routine dosimetry, the concentration estimated from the grab sample is assigned to the appropriate work area. It is then assumed that the concentration of radon progeny is equal to the average of the two measurements at the beginning and end of the specified interval. Meanwhile, the work locations and exposure times of each miner are recorded on the daily time card and verified by the shift supervisor. Most cards provide space for 15-minute time intervals. The exposure in working-level hours (WL-hr) for each shift is obtained by summing the time spent in a given location multiplied by the exposure rate (WL) assigned to that location.The exposure of an individual miner to radon progeny is summarized on a weekly basis and commonly reviewed each month. These values are then accumulated in units of working level- months (WLM) during the calendar year. EVALUATION TECHNIQUE AND RESULTS The evaluation of grab sampling methods for monitoring exposure to radon progeny is presented in two sections. The first section examines each method individually according to accuracy, precision, and uncertainties attributed to human errors. The second section includes an analysis of procedures which are common to all measurement methods. The ultimate goal is to determine whether a specific measurement method, or grab sampling in general, can fulfill the criterion that the annual accumulated exposure of each miner be known to within ± 50% at the 95% confidence level. In addition it is essential that the above criterion be satisfied at an acceptable cost to the mining company. The results of each testing procedure are presented in terms of the contribution of the relative uncertainty in the estimates of cumulative WLM. Each of these are then combined to form a figure of merit for the complete monitoring system. The method of combining statistical uncertainties and interpretation of the results is subject to some debate. However, since all of the tested parameters enter into the final computation of WLM multiplicatively, we have used the commonly accepted procedure of combining the squares of the relative uncertainties. We have also assumed that each of the uncertainties is derived from independent random variables and the covariance of any two variables is zero. A description of each grab sampling measuring method is given in Table 1. Also included is the equation used to compute WL from the measured quantities. Accuracy (U A) Our definition of accuracy is based on the uncertainty inherent in any method which attempts to estimate potential alpha energy without unambiguously determining the concentration of the three unknown radioisotopes, RaA, RaB and RaC. (For simplicity, the RaC and RaC' nuclides are referred to in combination as RaC.) The inherent uncertainty strongly depends on the mixture of these three components at the time of measurement.

Jan 1, 1981

By Patiño E

Bioleaching is an established technology for the pre-treatment of refractory gold ores and concentrates and the leaching of whole ore copper heaps. In many cases, it offers economic, environmental and technical advantages over pressure oxidation and roasting. However for bioleaching to compete successfully with others pre-treatment processes it needs to be optimized with regard to the parameters that affect the bioleaching reactions and the growth of the microorganism involved. In this sense, this paper focus on the thermodynamic approach applied in bioleaching through of the definition of the growth system and it is thermodynamics analysis, the effect of heat production and energy dissipation on growth and thermodynamic analysis of growth kinetics and the effect of nonstandard conditions.

Sep 12, 2005

By Alban Lynch, Benigno Aquino, Hakan Dündar, Alexander Kalugin, Marco Delgado, Alberto Palomino, Ali Türkistanli

Dynamic separators are efficient dry classifiers because new designs during the last 50 years have reduced the by-pass and improved the partition curve. By contrast cyclones have been used as classifiers in wet grinding circuits for 50 years but without serious change and the early problems which were caused by high and variable by-pass, and different mineral specific gravities, still exist. High frequency screens are now used for wet separation and the operating characteristics of closed grinding circuits using cyclones or screens are discussed. Data come from circuits at the Condestable, Cerro Lindo, El Brocal and Catalina Huanca mines in Peru, the Eczacibasi mine in Turkey, and the Apatit mine in central Kola Peninsula in Russia. All classifier data are described by their partition curves and all mill data by their breakage rates. With cyclones the by-pass, d50, and sharpness of the partition curve change as operating conditions change but with high frequency screens the values vary little because the by-pass is low, the sharpness is high, and d50 depends on the aperture size. Data from all plants indicate that lower by-pass and sharper separation improve breakage rates and throughputs. An initial model of the screen is proposed.

Jan 1, 2014

By M. R. Tek, K. H. Coats, D. L. Katz

In natural gas storage operations, seasonal pressure fluctuations in the gas reservoir cause the water from the surrounding aquifer to flow into and out of the gas sand. The theory of unsteady-state liquid flow through porous media developed by Van Everdingen and Hurst' has been applied to predict the water movement into and out of the gar bubble for .several .postulated pressure cycles. Those cycles with as many pound-days above the original aquifer pressure as pound-days below, may cause the gas reservoir to slowly grow or shrink rather than hold to a constant volume. Applications to an actual field case study give the predicted gas reservoir monthly pressures and volumes as compared with the observed monthly pressures and volumes. INTRODUCTION A large number of natural gas storage reservoirs are bounded by or adjacent to large water-saturated formations called aquifers. The presence of these aquifers is usually evidenced by the production of water from wells delineating the gas-hearing sands. Some gas storage reservoirs in use today have been purposely developed on aquifers. Cyclic pressure variations in a gas storage reservoir cause water influx and efflux from the surrounding aquifer. This, in turn, results in a varying gas reservoir volume. The prediction of the effect of this aquifer fluid movement on the size and size variation of the gas reservoir can provide information valuable in the study of several reservoir engineering problems. The economics of gas storage operations are directly influenced by the influx of aquifer fluid into the reservoir since a shrinking storage reservoir requires increasing pressures for the storage of the same quantity of gas. Material balance and reserve or recovery calculations also obviously require knowledge of reservoir volume. Various other reservoir engineering calculations such as interpretation of well interference data, evaluation of physical characteristics of porous media, water coning, gas injection and pressure maintenance studies are typical problems where variations of volume due to edge or bottom-water encroachment becomes important. The solution of equations describing influx and efflux of water in the gas sand, application to gas storage reservoir behavior and interpretation of results are the main objectives of this paper. While this work was directed toward gas storage reservoirs, it applies equally well to repressuring of partially depleted oil reservoirs with an active water drive. MATHEMATICAL ANALYSIS As just mentioned, the cyclic pressure variations in an aquifer-surrounded gas storage reservoir cause water movement and varying gas reservoir volume. Prediction of this volume variation from the reservoir pressure cycles or the injection-production schedule requires adoption of a flow model, certain assumptions concerning reservoir and fluid properties, and formulation and solution of the governing differential equation. The flow model used in this study is a gas bubble located on a very large aquifer (Fig. la). Gas bubble radius and aquifer sand thickness are denoted by rr and h, respectively. Fig. lb shows the horizontal, radial two-dimensional porous reservoir attended by the unsteady, compressible motion of the aquifer liquid. Volume variation of the gas bubble is determined from aquifer water flow across the cylindrical boundary, r = r0

By Shiou-Chuan Sun

The froth flotation of coal, differing greatly from that of most minerals1-5, is not improved but rather impaired by temperatures higher than room temperature6-10 This phenomenon has long taunted us for an explanation. Gayle and Associates 8,9 reported the lack of relationship between their contact angle measurements and their flotation of American coals under various temperatures. Bailey and Whelan6 stated that the viscosity of flotation reagents, offering some clue for their flotation of British coals at low temperatures, could not be put forward as an explanation either in whole or in part for the effect of temperatures on coal-flotation. In this paper, a froth hypothesis is proposed to explain the flotation behavior of coals under various pulp temperatures. Test work involved the flotation of coals and the frothing of reagents.

Jan 1, 1966

By P. C. O. Chukabarah

Many aerodynamic and thermodynamic properties, such as temperature, pressure, velocity and density vary widely, and in random spatial and temporal manner for a given underground mine environment. Such variabilities are seldom evaluated statistically, even though the relevant theories and principles for such an approach are both available and feasible. The main purpose of this paper was to introduce the new methodology of applying aerostatistics to the analysis of multiple fan system in mine aerology and/or ventilation. Pertinent data were obtained from a small multilevel coal mine. Results proved and confirmed that aerostatistical methodologies are computationally more efficient, grounded in solid engineering statistical theories, and can be used to analyze networked parameters in mine environmental engineering.

Jan 1, 1994

By W. Everett Smith

Factors that have influenced mineralization in the Valley and Ridge and Piedmont provinces in Alabama are not clearly understood. Lithology and structure are recognizable factors in the Valley and Ridge province, where barite, lead, and zinc sulfides occur in structurally complex areas of Cambrian and Ordiovician carbonate rocks. Metal mineralization in the Piedmont province indicates a complex relationship with factors such as favorable host rock, proximity to intrusive or high-grade metamorphic rocks, several metamorphic events and separate or related structural events. Lineaments, as used herein, refer to naturally occurring linear features consisting of topographic, vegetative or soil tonal alignments that are at least partially continuous for distances greater than a mile (Lattman, 1958). Lineaments in Alabama were first recognized by J. G. Newton in 1970, using Apollo 9 series photographs. Subsequent studies delineated the features (Powell and others, 1970) and suggested relationships to structural and hydrologic factors. More recent work has explored relationships to mineralization, environmental geology and the tectonic framework of the Appalachians (Drahovzal and Copeland, 1970; Drahovzal and Neathery, in press). The lineaments recognizable on Apollo 9 photography probably represent fractures, some of which may reflect geofractures that bound major basement blocks. The lineaments defined in Alabama range from about 4 miles to nearly 200 miles in length. Most of the lineaments are straight, but some are arcuate; some appear to terminate at the intersections with other lineaments but most cross each other with no offset. Some lineaments pass through areas of structural disruption such as terminations, offsets and changes in structural style, but others show no such relationships. Most of the lineaments appear to cross topographic features with little or no obvious disruption. Orientation analyses of the lineaments divide them into three directional groupings

Jan 1, 1972

At Appin colliery, geological structural analyses and investigations of roof conditions suggest roof failure may be attributed to vectorial stresses acting on underground openings, and inducing movement along inherent discontinuities in the surrounding rocks. Certain complex joint and fracture patterns tend to exhibit the effect of this movement resulting often in local deterioration in natural support.The following conclusions are drawn.1. Roof failure is related to the inherent nature of the roof rocks, the presence of mechanical discontinuities, and the vectorial stresses imposed upon it.2. Roof failure is not necessarily related to the statistically most prominent jointing.3. Colliery development approximately parallel to the direction of the statistically most prominent jointing sometimes results in favourable roof conditions.4. The maximum principal stress is the resultant of those vectorial stresses acting upon a mine opening and may be inferred from roof adjustments to those stresses after mining.5. Statistical analyses of jointing in the mine workings can provide clues to the tectonic force or forces which have been regionally or locally influential.6. There is a probable relationship between mining induced fracturing, jointing, and micro-fractures in quartz grains, within the sediments of the mine roof.

Jan 1, 1970

By Pierre Lacoste-Bouchet, Ian Orford, Mike Cooper

"The Brunswick Mine ore requires fine grinding to achieve liberation of minerals. With 25mm slugs as the grinding media in the ball mill, there was a limitation of a P80 of 25 microns on the CuPb regrind circuit. Results from pilot plant testing showed that the separation efficiency could be increased through fine grinding with a P80 of 15 microns.Options considered were the capital expenditure for new fine grinding equipment such as a vertimill or the use of the present ball mill equipment with smaller media. The Wheelabrator Allevard Enterprise (WAE) millpebs product was chosen because it was a smaller media with a distribution of steel pellets between 5 to 12 mm.With millpebs the grinding product was reduced in size from a P80 of 25 microns to a P80 of less than 19 microns. The power draw to achieve the finer grind was 13% lower while the media consumption was 57% higher.The millpebs grinding media was also tested on the zinc regrind mill. The purpose of the trial was to understand what the media consumption and power draw would be with the charge lowered to achieve an equivalent grind as obtained with the slugs. The media consumption was approximately the same and the power draw was reduced by 30%.INTRODUCTIONThe Brunswick Mine ore is a complex Pb-Zn-Cu-Ag sulphide ore with the grain size of the minerals varying from submicron blebs to particles up to several mm in size. The ore is ground progressively finer in stages. The first step of grinding occurs in the SAG mill circuit. The product sizing 80% passing 95 microns is fed to the CuPb prefloat stage (Cormier et al 2002). The tails from the prefloat is then further ground to a P80 of 35 microns for the CuPb rougher flotation. The final liberation for the CuPb circuit takes place in the CuPb regrind circuit. The regrinding mill further liberates the cleaner scavenger concentrate, second cleaner tails and third cleaner tails. The reasoning for the progressive grinding is to achieve fine grinding without having galena over ground due to its high specific gravity that preferentially sends it to the cyclone underflow."

Jan 1, 2006

Remediation of Mine Seepage at Batu Hijau

Sep 13, 2010

By George A. Lawrence, J. C. McHardy

"Field operating experience with an improved flotation mechanism for handling various flotation applications is covered in this paper. Some aspects of designing flotation machines are also presented. Operating data from extensive testing of commercial size equipment under actual plant operating conditions in the following applications is detailed:1. Copper Flotation2. Fine Coal Flotation3. Base Metal Sulfide FlotationDesign features, design improvements, modifications tested, and overall performance data are reviewed. Some mecl1anical performance data as well as metallurgical performance results are presented. Some comparisons with conventional flotation equipment are reported in this paper.Flotation sizing theories are reviewed and an actual equipment selection ex2.mple is presented. Scale-up criteria used for developing large cells are briefly covered.The paper concludes with a brief review of anticipated future flotation equipment design needs. IntroductionThe mining/milling industry is faced with increasing pressure to cut costs while maintaining product quality and indeed, in some instances, expanding production. For copper, nickel, iron, molybdenum, lead and zinc sulphides, coal, phosphate and some other minerals;, flotation remains the primary method of concentration and recovery of the valuable mineral away from the gangue. Cost reduction in flotation can be broadly focused on two areas:1. Flotation Chemicals2. Flotation Equipment"

Jan 1, 1985

By R Tweedie

'The politics of mining in New Zealand' is a topic I chose myself because of its importance in the future of the New Zealand mining industry. There are many people in the industry who are cynical about politics, cynical about politicians and definitely cynical and often critical of political decisions. In fact, many industry people say they don't want to get involved in politics, they just want to get on with the business of exploration or mining. The point of my address is that politics is important and the industry cannot afford not to participate in the political process.

Jan 1, 1991

By A. Lashgari, V. Kecojevic

This paper presents research on the environmental impact of digging and loading equipment used in surface coal mining. Environmental impact was assessed through the measurement of equipment exhaust and dust emissions, and sound level. In this study, exhaust emission refers to carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxides (NOx), sulfur oxides (SOx) and volatile organic compounds (VOCs). Dust generation refers to fine particles (PM2.5), inhalable particles (PM10) and total suspended particulate matter (TSP). Sound level refers to the sound pressure level at different distances from the equipment. Modeling of the environmental impact of digging and loading equipment was conducted using the Microsoft Visual Studio.NET software package. This research was a part of a broader project involving the development of a software system for the selection of productive, cost-efficient and ecofriendly mining systems, sponsored by the Appalachian Research Initiatives for Environmental Sciences (ARIES). This research may assist mining professionals in quantifying the environmental impact of digging and loading equipment, and developing strategies for reducing the overall impact of such equipment in surface mining.

Jan 1, 2013

By L. Lafrenière

A trend in mining exploration is to increase the number of geophysical parameters collected and interpreted for geological features in a given area. Airborne technology now allows us to simultaneously combine electromagnetic, gravity, aeromagnetic and radiometric surveys. We report the results of a multiparameter survey conducted in the area of Kamiskotia, Ontario. This area is located near and on the West side of the multi-metalliferous Kidd Creek deposit. Various metallic occurrences are reported in the studied area. Integrating multiple parameters in the interpretation produces a more detailed pseudogeological map than what has already been published. 3D interpretation has been undertaken using some of these parameters and suggests that future work is required in 3D earth model solutions in order to fully use all parameters.

Aug 1, 2013