Search Documents

By W. G. Pariseau

Introduction Caverns of 50 m in linear dimension at depths below 2300 m with a life of more than 25 years are proposed for the next generation of water-filled neutrino detectors. Little precedent exists for excavations in such an extreme environment, although some guidance is available from mining experience at great depths, for example, in South Africa, in Canada and at the former Homestake Mine in the U.S.A. Unlike mining for ore, there are choices available in the construction of such caverns that may mean the difference between success and failure. These choices should be informed by rock engineering principles. Recently proposed guidelines for orientation of brick-shaped caverns where the long dimension is a small multiple of the short dimension indicate that the most favorable orientation is with the long and short dimensions parallel to major and minor preexcavation principal stresses (Pariseau, 2005). Numerical analyses at reduced strength indicate some yielding at cavern walls should be expected but that an equilibrium state is quite possible and is aided by arching the back into a spherical dome when the cavern is an empty cylinder (Tesarik and others, 2002). The same indications of stability occur with brick-shaped caverns. However, the most dangerous situation occurs during the excavation sequence to final cavern dimensions. There are any number of excavation sequences that lead to the same final cavern shape, so there is an opportunity to partially optimize the sequence with construction guidelines that minimize peak stress concentrations during construction. This contribution discusses three practical excavation sequences that lead to the same brick-shaped cavern in the strong, massive Yates formation at the Homestake Mine where considerable rock mechanics data has accumulated through the years(e.g., Pariseau, 1985, Pariseau and others, 1995) and where actual mining on the 8000 Level indicates a strong possibility of successful investment in the next generation of large, deep neutrino detectors. The main results are: (1) a favorable brick-shape is one with dimensions in the same proportion as the preexcavation principal stresses (compressionpositive), and (2) favorable orientation of the most extreme but temporary shape of excavation is also best for the construction sequence. Analysis results from a mix of Homestake Mine data and possible excavation geometry illustrate the advantages of these guidelines.

Jan 1, 2006

By Louis A. Panek

Tests of mine-roof models in a centrifuge show that the suspension effect due to bolting a horizontally bedded mine roof with frictionless surfaces of contact between beds depends principally on the number of bolted beds and their relative flexural rigidities, provided that sufficient bolt tension is exerted to prevent strata separations at the bolt locations. Strata separations tend to occur in the unbolted roof mainly because the beds have unequal thicknesses. "Suspension effect" refers to the transfer of part of the weight of weaker or thinner beds to the flexurally more rigid beds by roof bolts or by any other means. The factors investigated were number of beds in the bolted unit, bed thickness, modulus of elasticity of beds, length of bolts, spacing of bolts across and along the opening, bolt load, and intensity of roof load. The general principles of behavior of the bolted roof beds are explained by an approximate theory. Model test data are used to validate the theory and to obtain an expression for the "suspension efficiency". As the suspension effect actually observed in the models is smaller than that predicted by the approximate theory, the suspension efficiency in general is less than unity. Mathematical expressions are obtained for (1) the change in roof bending stress due to the suspension effect, which is needed for design of a roof-bolting system, (2) the change of roof deflection due to the suspension effect, which may be useful for evaluating the effectiveness of a roof-bolting system, and (3) the bolt load or pre-load that is required to achieve the desired reinforcing effect.

Jan 1, 1962

By R. T. Stain

Integrity testing of deep foundations is now common practice in Europe, indeed in the City of London such testing is a contractural requirement on every site. This paper is in two parts: Part 1 describes the most commonly used test methods and their applications. Part 2 presents a case history where both of the above techniques were used.

Jan 1, 1987

By Steve Kral

For the past several years, copper producers have faced a tough business climate. Nagging low prices forced many them to reduce their production and make other drastic cutbacks just to breakeven. And sometimes even that did not work. But, like other downturns in the industry, this latest dismal copper market allowed technology to make further inroads into mining and processing operations. Now that the copper market appears to be making a turn for the better, those years spent investing in technology by equipment manufacturers and forward-thinking mining companies should begin paying off.

Jan 1, 2004

By Takashi Saito

Since early 1970?s skirt suction foundations (skirted foundation / bucket foundation) have been used as support for large fixed substructures or anchors for floating structures in offshore hydrocarbon development projects. In recent years skirt suction foundations are recognized as one of the solutions in foundations applicable to bridge substructures installed in waters, because skirt foundations have a wide variety of functions such as control of settlement during service life, less impact to environments during operation at installation site. This paper introduces general features of skirt suction foundations, and then discusses design practice of them for the application to bridge substructures, with reference to experiments in both laboratory and field.

Jan 1, 2013

By Brad R. Blair

This paper will review impacts on longwall design and ground stability assessment due to advances in mine automation and sensing technology. Several new approaches to the prediction and monitoring of longwall panel and gateroad stability have recently become mature, and are ready for application in problematic ground control situations. These methods are revealing significant detail regarding deformation and failure mechanics of critical underground structures. Examples of how these technologies have worked successfully will be given, and applications for the use of these tools for cost-effective engineering design and monitoring will be suggested.

Jan 1, 1996

By M. T. Erickson, C. A. Rowland

Ball mills 5.5 m (18 ft) in diameter and larger tend to use energy delivered to the mill less efficiently than smaller diameter mills, particularly when the large mills carry 40% by volume ball charges. This paper will explore factors used in scaling up ball mills, showing where the advantages of one factor can possibly be negated by another factor. The paper will propose possible operating limits and areas for further study to establish selection and design limits.

Jan 1, 1985

By R. A. Triglavcanin

Delivering dilution water and mixing this water with incoming feed slurry, addition of flocculant, maximising flocculant-slurry interaction to build aggregate size, unabsorbed flocculant percentage, volume average of solids volume fraction, momentum dissipation ratio, dilution recycle ratio, volume average shear, maximum shear rate at exit, aggregate size on exit, uniform discharge profile and more ? all of these need to occur in the right order and in the right proportions within the thickener feedwell, the secret to thickener performance.

May 1, 2009

By Osvaldo A. Bascur

Standards and technology for bringing information to the desktop have greatly evolved in recent years. The benefits to be realized depend on how these new tools are embraced at the performer level. A key operating challenge is to ensure cooperative effort is geared towards the most efficient achievement of identified operating and corporate objectives. Presentation, application and database layers are emerging in successful client/server applications, the three-tier architecture.

Jan 1, 1996

By Harry Teicher

The subject of Specialty Silica Products could encompass a broad range of materials, some of which would be familiar to members of the Society of Mining Engineers. With the concurrence of your chairman, I have chosen to limit my remarks to synthetic materials, not including such siliceous materials as diatomaceous earth, asbestos, quartz and clays. For purposes of discussion, I have classified Specialty Silica Products into two groups -- powders and liquids -- which I will discuss in that order and which are categorized in Figure 1. The synthetic silica powders are amorphous to x-rays and are manufactured by various processes resulting in products of a wide range of physical and chemical properties, as well as functional performance and applications. Applications or functional properties are generally dependent upon such physical properties as micron-sized particles exhibiting large surface areas per unit weight and low apparent bulk density. Their presence in various systems modify surface properties. As summarized in Figure 2, they act as viscosity modifiers, flow conditioning agents, anti-slip agents, anti-blocking agents, flatting agents in surface coatings, reinforcing agents in polymers such as silicone rubber and numerous other applications. Although the various types of silicas exhibit various levels of functional performance in these end uses, they are not usually equally effective as direct replacements and I will briefly discuss the various types of materials.

Jan 1, 1974

By Victor E. Kral

"SUMMARYA preliminary examination of the Buena Vista iron deposit was made in June 1942 by Paul E. Pesonen, mining engineer of the Bureau of Mines. Subsequent examinations were made by D. W. Butner, of the Bureau, in March 1943, and by the author in July 1944, who recommended exploration by diamond drilling, trenching, and sampling. Work on the project was done during the period March 28 to May 26, 1945.Property holdings, comprising 16 claims known as the Buena Vista group, are situated in sec. 4, T. 24 N., R. 34 E., Mount Diablo base and meridian, north Churchill County, about 37 miles east of Lovelock, Nev.Three diamond-drill holes totaling 575 feet were drilled; 45 small pits and ten trenches, totaling 435 linear feet, were excavated, and 84 channel samples totaling 862 feet were obtained under supervision of the Bureau.Purpose of the project was to determine the possible downward extension of the mineralized sections exposed in the outcrops and to determine grade of the ore.Bureau work was confined to one claim only - the Iron Mountain."

Jun 1, 1947

By R Yang, M Lownds

This paper reports studies showing the effects of delay scatter on the peak particle velocity (PPV) of blast vibration using a multiple seed wave (MSW) vibration model developed in recent years. The case studies also show the advantage of accurate delay timing on frequency control of blast vibration. The site parameters used in one of the studies are from a case in which the MSW model has been tested and confirmed to yield accurate predictions. This study uses an open pit blast design and a tunnel design in which blast vibrations using electronic detonators are compared with those from pyrotechnic detonators. Mean peak particle velocity (PPV) and the 97.5% upper bound PPV are compared. It is found that both these values increase significantly with the increase of the coefficient of variation of the site parameter. Using an open pit blast design, the modeling shows that electronic initiation shifts vibration energy to the expected frequency for a selected point of interest. However, for the same design of nominal initiation timing pyrotechnic detonators fail to shift vibration to the expected frequency due to its large scatter of timing.

Jan 1, 2011

The Australian Mineral Industry's growth in the last two decades is directly related to the skill and experience of its consultants in mining, metallurgy, geology, finance, management, marketing, and engineering. The role of mining consultants needs to be re-examined, so that the quality of the service they deliver will continue to be adequate for the 1990's. One means of this evaluation is by examining Case Studies in the strategies and difficulties of developing contract and entrepreneurial research.

Jan 1, 1986

By Silvando Vieira dos Santos

O emprego de trabalho mecânico em ligas metálicas associado a aplicações de tratamentos térmicos estão entre os principais métodos para se conseguir alcançar aumento de resistência mecânica e manutenção de boa ductilidade. Este estudo busca avaliar a correlação entre deformação a frio, tratamento térmico, microestrutura e propriedades mecânicas da liga Ti35Nb2,5Sn. Para isso realizou-se laminação a frio empregando níveis de redução equivalentes a 70%, 80% e 90%. Em seguida, as amostras foram analisadas por meio das técnicas de microscopia ótica, difração de raios X e microdureza Vickers. Na sequência, tratamentos térmicos de envelhecimento foram aplicados em diferentes tempos para cada nível de deformação e os mesmos parâmetros foram avaliados. Observou-se significativo aumento de dureza após etapa de envelhecimento e as análises por metalografia e difração de raios X evidenciaram a presença de fases metaestáveis na matriz beta..

Oct 30, 2017

By F. Ajersch, M. Rigaud, M. Jallouli

"Le gonflement des boulettes d'hématite à été étudié à l'aide d'une méthode de mesure standard ISO ainsi qu'à l'aide d 'une méthode de mesure dilatométrique.La première méthode a servi à l'étude des boulettes haute silice (5% SiO2) dont l'indice de basicité (IB = CaO + MgO -i- SiO2 + Al2O3) a été ajustée soit à l'aide d'une addition de dolomie, soit à l'aide d'une addition de pierre à chaux, soit à l'aide d'une addition de ces deux composes. L'indice de basicité variait de 0.05 à 0.12. Les résultats de gonfle ment obtenus à 1000?C dans une atmosphère de 40 CO - 60 N2 ont permis de montrer qu’indépendamment de l'indice de basicité c'est la dolomie qui contribue le plus à diminuer le gonflement par rapport à la pierre à chaux. L'utilisation de l'indice de basicité comme critère de sélection des boulettes est discutée.La méthode dilatométrique a servi à l'étude du gonfle ment de deux types de boulettes préparées à partir de deux concentrés de fer et dont la teneur en silice a été fixée à 2.5% et 0 5%. Ces deux types de boulettes ont reçues les mêmes additions de liant en quantité et en nature. La détermination en continue du gonflement, à 950?C dans 40 CO - 60 N2, a permis d'une part de mieux cerner le niveau de réduction auquel correspond le maximum de gonflement et d'autre part de montrer que l’allure des courbes de gonflement est étroitement liée à la nature du liant. Une augmentation de la teneur en silice des concentres contribue à diminuer le gonflement des boulettes.Des essais de réduction de gonflement non isothermes ont été réalisés à des montées de température à 10 et 20?C/min. Les résultats indiquent que le gonflement déterminé dans les conditions non iso thermes est inferieur à celui obtenu lors des essais isothermes. On discute alors de la validité des essais standards de gonflement qui sont utilisés pour prédire le comportement des boulettes lors de leur réduction dans un haut fourneau."

Jan 1, 1983

By Guangqing Zhang

The paper presents results of a systematic study of synthesis of titanium oxycarbide and its chlorination. Titanium oxycarbide was produced by carbothermal reduction of titania in hydrogen, argon and helium. Formation of titanium oxycarbide started at 1200°C in all gases. The reduction was the fastest in hydrogen. Formation of titanium oxycarbide in hydrogen was close to completion in 120 min at 1300°C, 60 min at 1400°C and less than 30 min at 1500°C. Reduction in argon and helium progressed at a similar rate and reached 90-95% after 300 min at 1400-1500°C. The chlorination of titanium oxycarbide was ignited at 150-200°C. Chlorine partial pressure and gas flow rate strongly affected the chlorination rate. Chlorination of titanium oxycarbide produced with carbon to titania molar ratio 2.5 at 235-400°C was close to 100% in 30 min.

Jan 1, 2009

By D. Nag, J. Fernando

Hazelwood Power Mine is one of the largest open pit brown coal mines in Australia. The removal of overburden is the first step in coal winning operation. The primary aim of construction of overburden dump is to provide an effective stable working surface for stacker. The paper discusses site investigation techniques used to determine dump soil properties, stability analysis method using GALENA and GWEDGEM, results of stability analysis. The paper concludes with recommendation for a safe dumping strategy for level 2 stacker dumping.

Jan 1, 2003

By C. F. Weinaug, R. W. Farley, J. F. Wolfe

A rapid, accurate method for predicting the dew points of gas condensate systems and their subsequent normal and retrograde phase behavior with pressure decline has been developed. The method predicts dewpoint pressure, volume percent liquid, condensate content of produced gas, and the liquid and gas compositions at pressures below the dewpoint pressure. Use of a modified form of the BWR equation of state, which was established by regression calculations on experimental data from several gas condensates, provides depletion behavior predictions that are significantly improved over predictions using K-values based on convergence pressures and Standing's correlation for density. INTRODUCTION Prediction of complex hydrocarbon-mixture thermodynamics is fundamental to reservoir and gas process engineering. In particular, accurate descriptions of phase behavior are needed to plan production operations for gas-condensate reservoirs. Although analysis of reservoir behavior during producing and cycling operations can be made for simple reservoir models, extensions of these studies to more complex reservoir systems are still difficult, both with regard to numerical techniques and the phase behavior of the fluids. This report presents a mathematical method for handling the complex phase relationships encountered in retrograde condensates; it represents an advance in reservoir behavior technology in that it will aid the development of closed-form mathematical representations of total production systems. A typical phase diagram for a complex hydrocarbon mixture is shown in Fig. 1. When the reservoir temperature T, is higher than the critical temperature Tc, and lower than the critical-condensation temperature Tct' the mixture is a gas condensate. Decreasing the pressure on a condensate while maintaining nearly constant temperature will result in two phases forming at the dew point. Further decrease in pressure will cause additional liquids to be formed. This phenomenon is called retrograde condensation. As pressure continues to decrease, normal phase behavior regions are encountered (liquid vaporizes as the pressure decreases) until the low-pressure dew point is encountered. When a gas-condensate reservoir is produced, gas is withdrawn and the volume of fluids in the reservoir remains nearly constant as the pressure declines. Heavier components tend to accumulate in the liquid phase as a result of retrograde condensation, while lighter components tend to concentrate in the vapor phase. Thus, as the gas is produced the composition of the gas and the condensate

Jan 1, 1970

By M. G. Papasotiriou

For our company, S&B Industrial Minerals S.A., restoration of areas which were mined and the effort for bringing up again a balance of nature is an important priority over the last 3 decades. The successful qualitative results of restoration works have delivered to nature over 1.700.000 m2 of surface after mining activity. Our fundamental method in order to achieve the best results for restoration of mined areas is the use of local plants (bush or tree type). Grass and herbs are installed by using the method of hydroseeding. Small trees and bushes are produced and they grow up at our fully owned Milos nursery and they are installed during winter when weather conditions are suitable. During the initial stages of restoration activities a great amount of surfaces, adequately shaped, are delivered by the mining department covered with top soil. These surfaces are suitable not only for the local nature community but also for a combination between natural and agricultural environment. The above fact was a great chance to create small horizontal agricultural cultivations as pilots inside the restored areas. At the beginning the agricultural items that could potentially be installed in these pilot areas were studied and examined analytically. The following agricultural items were finally qualified to be furthermore researched: 1) Vineyard (Vitis vinifera ) 2) Prickly pear (Opuntia ficus indica) 3) Jojoba (Simmonsia chinensis) 4) Olive tree (Olea europea)

Jan 1, 2007

By Carrol A. Quam

DURING the first years of operation of the titanium and iron mine of the National Lead Co. at Tahawus, New York, efforts to increase production were hampered by the increased load put on the facilities for sharpening churn-drill bits. The ore and rock are extremely hard and abrasive and it was necessary to sharpen and harden a large number of bits per day to keep the churn drills supplied. Efforts to increase the capacity of the bit shop by a two-shift operation were not wholly successful in that it was hard to train men to do a satisfactory job of sharpening and tempering the bits. The number of bits that were improperly tempered increased, thus boosting the daily requirements for bits at the drills and increasing the load on the bit-sharpening facilities.

Jan 1, 1949