Search Documents

By M. L. Holzworth, Philip R. Sperry, Paul A. Beck

INTRODUCTION THE basic work of Z. Jeffries1,2,3 has long ago established the main features of grain growth in the presence of a dispersed second phase. Working with sintered specimens of initially fine grained tungsten, to which various amounts of thoria have been added, Jeffries found that grain growth was inhabited, that is, practically prevented, up to a certain annealing temperature. When this temperature, which increased with the thoria content, was exceeded, extremely large grains developed abruptly from the fine grained matrix. Such a "coarsening temperature" was later found by Gross mann13,14 in certain types of steel, while Bain showed" that in other steels grain growth was gradual, without inhibition and abrupt coarsening. Later work16,17,18,19,21 demonstrated the connection between coarsening and aluminum additions. The viewpoint that the direct cause of inhibition and coarsening in aluminum killed steels is a fine dispersion of aluminum oxide21 appears to be held quite generally, although some doubts have been voiced even very recently.20 In steels with Ti additions the titanium carbide phase is considered responsible for the inhibition effects found.20 The coarsening temperature increases, with the titanium content. That coarsening may occur, as a result of certain heat treatments, even in low carbon rimmed sheet steel, was shown by Samuels,22 He also detected coarsening in a steel ingot of similar composition, after giving it the same heat treatment as that used by him for the sheet material, In this instance the identity of the inhibiting phase has not been determined, However, Tangerding found 23 that even the few small carbide particles, which occur in carbonyl iron, have a very marked inhibitive effect. As a result of an oxidizing anneal at 850°C, large grains begin to form at the surface of the carbonyl iron specimen, and gradually grow inward as the subsurface oxidation of the carbide particles progresses and eliminates the obstruction, The carbide particles can be removed also by annealing in hydrogen, with similar results. But if the oxidizing anneal of 10 hr at 850°C in air, is followed by annealing in hydrogen for 75 hr at the same temperature, grain growth is more spectacular; usually the whole specimen is transformed into a single crystal (approx. 1,5 cm X 5 cm). The reversed procedure, that is, hydrogen annealing followed by oxidizing annealing leads to smaller grains. Tangerding arrived at the logical conclusion that there must have been in his specimens some additional obstruction to grain growth resulting from a minor impurity, other than carbon. It seems likely that this obstruction was caused by an oxide formed during the oxidizing anneal and gradually reduced during the subsequent hydrogen-annealing. Other instances of grain growth inhibition of varying severity, associated with a dispersed second phase, have been described by several authors. Notable examples: lead with 0.06 pct Cu or Ni,24 cartridge brass with 0.12 pct Cr,25 or with up to 0.15

Jan 1, 1948

The oxidation of sulphide minerals in aqueous suspension is discussed from several viewpoints. Limitations of our present knowledge are pointed out, and several points where further information would be of special interest are mentioned.Firstly, some properties of minerals and their effect on oxidation are discussed. Properties of different species, such as crystal structure, lattice bonding, and "metallic" properties are mentioned, and then the effect of variation within a given species is discussed. The effect of physical factors, especially particle size, is also considered. Other variables discussed include the importance of solution composition, and its effect on the nature and rate of reaction, and the use of various oxidising agents. Some factors concerned with the whole system, such as temperature, pulp density and stirring rate are then considered.Finally, the nature of various oxidation products is discussed with reference to the kinetics of reaction and the nature of the rate limiting step. It is suggested that more attention should be paid to electrochemical explanations of the reaction mechanism.INTRODUCTIONKnowledge of the factors governing the rate of oxidation of sulphide minerals in aqueous suspension is a prerequisite for the effective control of many ore treatment operations. Rapid oxidation of sulphides is usually desired during the leaching of sulphide ores and concentrates, but in the cyanidation of gold ores, or in the leaching of uranium ores, any oxidation of sulphides may be regarded as an undesirable side reaction. Knowledge of many of the factors involved is also of interest in connection with the oxidation of sulphides in flotation circuits and in natural ore forming processes.Systems for which some reasonably quantitative data have been published are listed in Table 1. Qualitative...

Jan 1, 1961

By R. Q. Shotts, H. J. Hager, A. C. Richardson, G. D. Coe

"INTRODUCTION In the State of Alabama few mines produce coal clean enough to be marketed directly without being washed. This is particularly true where the coal is to be used for the production of metallurgical coke. In washing plants where single-compartment jigs alone are used to treat a large range of sizes, it has been found that the washed coal finer than 1/4-inch contains a large proportion of free impurities and is much higher in ash content than are the coarser sizes. To reduce the ash content of this fine material with jigs usually entails a greet reduction in capacity and a loss of coarse coal in the refuse. This investigation, conducted by the Southern Experiment Station of the United States Bureau of Mines in cooperation with the University of Alabama and the Alabama By-Products Corporation, was undertaken to determine whether the fine washed coal from jigs could be economically re-treated on coal washing tables.COALS TESTEDThrough,the cooperation of the Alabama By-Products Corporation, samples of fine-sized washed coal were obtained from their washeries at Bradford and Gamma.The Bradford mine, on the Black Creek bed, yields a low-ash, medium-volatile coal with fairly good coking properties. This coal is blended with coal from the Mary Lee bed for coking purposes and compensates for the high ash content of the latter. The Black Creek bed is about 30 inches thick and seam analyses show an ash content of from 2.0 to 4.0 per cent. In the Bradford mine the undercut is about 6 inches high, so that a large proportion of fines is produced."

Apr 1, 1932

By Harald F. Solberg

A preliminary study of the performance of a 4-inch Krebs cyclone at near rope conditions and different feed slurry temperatures was completed. Results suggest that temperature influences the x50c size which, in turn, did not depend upon spigot diameter. The bypass correction to a reduced efficiency equation incorporating the concept of a critical size xo was a function of fractional water recovery to underflow and may depend on feed size and feed percent solids. Further experimentation is required to develop an accurate model at near rope conditions.

Jan 1, 1981

By N. Niemuth

Strong demand for copper in developing nations such as China and India, plus the additional demand for industrial minerals to supply the Arizona construction market, brought about a record-setting year for the state?s mining industry. The value of Arizona?s copper production set a new high of $5.5 billion and pushed the total value of mineral production to $7.58 billion. This was also a record. As it has for many years, Arizona ranked first in nonfuel mineral production in the U.S. In addition to leading the nation in copper, Arizona ranked in the top five in molybdenum, sand and gravel, gemstones, perlite, silver, zeolites and pumice. Generally strong and rising prices, especially toward year?s end, fostered a bullish atmosphere that encouraged significant levels of acquisition and exploration. This activity has spread beyond the normal commodities to include some, such as manganese and fluorspar, that have not been mined in Arizona for decades.

Jan 1, 2008

By V. Mathebula

Paper written on project work carried out in partial fulfilment of B. Tech (Mining Engineering) degree The purpose of this study is to establish whether to mine the Bottom of Pit (BOP)/TOB 4 reserve before the commencement of the Block Cave or whether this should be disregarded and the reserve be extracted at the end of the life of the Cave. The primary goal of this report is to investigate and propose a practical mining method to safely extract the reserve given the set constraints. This report quantifies the additional revenue the TOB 4 will contribute to Finsch?s overall NPV thus enhancing Finsch?s business case and strategically enhancing the SBP. Several underground mining options have been investigated. The proposed mining method includes the installation of a series of extraction tunnels below the TOB 4 reserve from 53 level, with a slot access tunnel system. Ground will be loaded by LHDs from the draw points and tipped into 50-ton dump trucks at a transfer point, from there the ground will be transported to 53 level No. 1groundpass where it will join the existing ground-handling system. Primary development is scheduled to begin October 2002 and last for a period of approximately 7 months until early April 2003.The production is broken into 4 phases. Phase 1 is scheduled to begin mid-April 2003. The final production phase will be completed by November 2005. The production scheduling has been designed in order to remain ahead of the Block 4 undercut in order to ensure stability and safety. Due cognisance was taken of the health and safety of all employees concerned during the design of the mining and ground-handling processes for the Bottom of Pit. As far as is reasonably practicable, the BOP was designed and will be constructed and equipped to provide conditions for the safe operation of machinery and a healthy working environment for people underground. Relevant requirements of the Mine Health and Safety Act regulations pertaining to mining operations have been identified and adhered to during all phases of the design process.

Jan 1, 2004

By G. Zhan, P. Mousset-Jones, G. Danko, J. J. K. Daemen, C. Mezei

Paper presented at the conference Risk assessment in the extractive industries, held in Exeter, 23-24 March 1994, and first published London: IMM, 1994, preprint volume. 18pp., 12 refs. (Originally entitled: Tunnel roof diagnosis using a robotic sensor test bed.) An integral roof diagnosis method is proposed to assist in assessment of risk regarding the stability of an excavation. A Robotic Sensor Test Bed (RSTB) is being developed for the characterisation of roof stability. The sensor test bed consists of a sonic/ultrasonic wave response sensor, a laser surface profiler and a surface temperature sensor. These sensors are mounted on an articulated robot manipulator for performing remote-controlled or fully automated diagnoses. A number of laboratory and field sonic/ultrasonic tests were conducted. A high-energy ultrasonic transducer and an impact device were used to resonate rock slabs. The fracture depths of the slabs were found to be inversely related to the measured resonance frequencies. The agreement between identified and actual dimensions was acceptable. Field tests also showed that loose rock on the surface can be clearly distinguished from solid formation by comparing their wave responses. The robotic laser profiler part of the RSTB was used to measure surface geometry. Different scanning methods are being developed to achieve the fastest and most precise measurements and to provide pertinent information about rock joints and major fractures

Dec 1, 1994

By Robert K. Steunenberg, Irving Johnson, James B. Knighton

The activity coefficient of plutonium in liquid magnesium, over the temperature range 650° to 800°C, was obtained from measurements of the distribution of plutoninm between a 50 mole pct MgC12-30 mole pct NaCl-20 mole pct KC1 molten-salt mixture and liquid Zn-Mg alloys. For dilute solutions (0.08 at. pct Pu) the activity coefficient of plutonium was found to vary from 10.1 at 650°C to 12.2 at 800°C. The activity coefficients of plutonium in dilute liquid solutions of plutonium in uranium, silver, lanthanum. cerium, and calcium were estimated to be. The distribution data indicate a value of about 0.1 at 800°C for the activity coefficient of PuCl3 dissolved in the above ternary salt mixture. LIQUID magnesium and several liquid alloys of magnesium with metals such as zinc and cadmium have been shown to be useful solvents in pyrochemical processes for the recovery of uranium and plutonium from discharged nuclear fuels,' and for the separation of transuranium elements.' The present study was undertaken to determine the activity coefficient of plutonium in liquid Pu-Mg alloys in support of process-development work. The activity coefficient of plutonium in liquid magnesium was determined from experimental data on the distribution of plutonium between a liquid ternary MgC12-NaC1-KC1 salt mixture and various liquid Zn-Mg alloys. The distribution data were used to calculate the ratio of the activity coefficients of plutonium in liquid zinc and in liquid magnesium. The activity coefficient of plutonium in liquid magnesium was then computed from the known activity coefficient of plutonium in liquid zinc. It was not necessary to know the thermodynamic properties of the molten-salt system explicitly. The major features of the Pu-Mg system have been reported by Schonfeld.3 At the temperatures of interest in the present study, i.e., above about 600°C, the phase diagram indicates the existence of a wide liquid-miscibility gap, with the plutonium-rich liquid containing about 8 at. pct Mg and the magnesium-rich liquid containing about 10 at. pct Pu at the intersection with the solidus regions. Additional data on the compositions of the two equilibrium liquid phases obtained in this laboratory4 have defined the miscibility gap up to the consolute temperature (at about 1040°C). EXPERIMENTAL PROCEDURE AND RESULTS Materials. The 50 mole pct MgC12-30 mole pct NaC1-20 mole pct KC1 salt mixture was prepared by melting the required proportions of reagent-grade NaCl and KC1 with anhydrous MgC12. The molten salt was then purified by contacting it with liquid Cd-30 wt pct Mg alloy (at 450°C) to reduce oxidizing impurities, followed by filtration through a stainless-steel frit (pore size, 65 µ) to remove solid MgO formed during the reduction. The purity specifications of the zinc, magnesium, and plutonium were 99.999, 99.8, and 99.85 pct, respectively. Apparatus. The liquid salt and metal were contained in a tantalum crucible inside a graphite secondary vessel. The crucible assembly was located inside a resistance-heated stainless-steel furnace tube. The furnace tube was closed by means of a stainless-steel cover, which was attached by bolts, with a neoprene O-ring serving as a gas-tight seal. The top of the furnace tube was water-cooled to protect the O-ring. The furnace-tube cover was provided with a tantalum thermowell, a tantalum stirrer, and a port through which sampling tubes could be inserted and materials could be added to the melt without admitting air to the furnace tube. Vacuum and an argon atmosphere were available through a side-arm on the furnace tube. The furnace temperature was regulated by a proportional controller that was actuated by a chromel-alumel thermocouple between the furnace tube and the heating elements of the furnace. The melt temperature was measured by means of a chromel-alumel thermocouple in the tantalum thermowell. The accuracy of temperature measurement was ±3°C. The salt and metal phases were intermixed by a motor-driven tantalum paddle positioned at the liquid interface. The tantalum crucible was provided with four baffles to increase the turbulence. The sampling tubes consisted of 1/4-in.-OD tantalum tubing that terminated in a tantalum frit (Kawecki Chemical Co.; average pore size, 30 µ). Procedure. The zinc, magnesium, plutonium, and salt were charged to the tantalum crucible; then the system was evacuated and filled with argon. The melt was brought to the desired temperature, and agitated for 1 to 2 hr. After allowing the salt and metal to separate, both phases were sampled. Filtered samples were obtained by immersing the end of the sampling tube in the liquid and increasing the argon pressure sufficiently to force the liquid salt or metal through the frit into the tantalum tube. The sample was then partially withdrawn into the cooler portion of the furnace tube and permitted to solidify before being removed. The temperature sequence for sampling at each magnesium concentration was 800°, 700°, 600°, 650°, and 750°C. The composition of the liquid-metal phase was varied by incremental additions of magnesium in a series of experiments at low magnesium

Jan 1, 1967

By T. F. Tomb

on' January 6, ,1992, the Mine Safety and Health Administration (MSHA) issued an Advanced Notice of Proposed Rule Making (ANPRM) for diesel particulate (DP). The ANPRM identified five areas where the Agency was seeking additional information to assist in the rule making process. These areas were exposure 'limits, risk assessment, consideration of other information, sampling and monitoring methods, and feasibility. The period for submitting information relative to the ANPRM closed July 10, 1992. Prior to issuance of the ANPRM, the agency was involved in conducting studies to evaluate sampling and control technologies and to gather information with respect to occupational exposures to diesel particulate in underground mining operations employing diesel-powered equipment. Since issuance of the notice, additional studies have been conducted to provide supplementary information in these specific areas. Results of these additional studies indicate that average DP levels in coal mines not using aftertreatment range from 0.9 to 2.1 mg/m3. Aftertreatment devices can reduce these levels by approximately 50 to 90 percent. Studies conducted in metal and nonmetal mines showed average DP levels ranging from 0.3 to 1.6 mg/m3.

Jan 1, 1994

By Fengnian Shi

In the current energy-sensitive world, sustainable development in the mineral industry will require new, better and more efficient processes. Novel comminution methods, which offer the prospect of achieving the required outcomes of size reduction and mineral liberation at lower energy consumption, are continually being sought. In the past five years, extensive research using high voltage pulse electrical comminution technology has been carried out at the Julius Kruttschnitt Mineral Research Centre (JKMRC), in collaboration with selFrag AG. The major outcome of this research is the development of the concept of pre-weakening ore particles by electrical comminution procedures to reduce the energy consumption in the downstream grinding circuit. The research has also verified the preferential liberation of valuable minerals by electrical comminution. Given the advantages, several potential applications of electrical comminution in the mineral industry are proposed, including AG/SAG mill feed pre-weakening, pebble treatment, ball mill feed pre-weakening, early recovery of the liberated valuable minerals, crack/micro crack generation for improved leaching, and smelter slag treatment. For the mineral industry to utilize electrical comminution, two emerging issues identified from the research need to be address. They are the energy consumption by electrical comminution in the locked cycle treatment and the facilities scale up necessary to move this technology from the laboratory to the plant. Keywords: high voltage pulses, electrical comminution, energy efficiency, mineral liberation

Sep 1, 2012

This paper summarizes the results from a project aimed at adapting scroll centrifuges for application to the dewatering of flotation concentrates. The main impetus for the project was to reduce the high cost and footprint size of the technology currently used to dewater fine coal. The technical challenge was to enhance solids capture by incorporating a laser-cut screen into the design of the basket. The project has shown that a pilot-scale scroll centrifuge can be used to dewater froth concentrate. A number of different basket designs were tested, the best results being achieved with a basket comprising a laser-cut screen of aperture 70 µm. The best result on a sample of untreated flotation concentrate, which was taken from the open trough flotation cells at a coal preparation plant (CPP) in NSW was a solids recovery of 82 wt% at a product moisture of 24.3wt%. By comparison the best product achieved with a conventional wedge wire basket was a similar moisture content but solids recovery was only 64 wt%. This could only be achieved after the feed had been artificially thickened. Conditioning of the centrifuge feed with polymer flocculants led to an increase in recovery up to 88 wt% with a moisture content of ca 25 wt%. It is thought that optimizing additive selection and conditioning parameters, as well as screen aperture and open area, could improve performance still further. The results were obtained using centrifuging conditions (centrifugal force, feed solids, feed rate) in the pilot-scale machine which should be possible to translate into conventional designs of commercial scale machines, without downgrading solids throughputs. However only with full-scale trials will it be possible to establish this assertion with certainty.

Jan 1, 2001

By M. R. Bitarafan

Mining method selection is the first and most important problem in mine design. In this selection some of the parameters such as geological and geotechnical properties, economic parameters and geographical factors are involved. The mining engineer must balance the input parameters and select the method that appears to be the most suitable; mining method selection is both an art and a science. Distinguishing all parameters that have an effect in mining method selection and in the determination of weighting factors of any parameter is a difficult task in an ordinary environment. This paper attempts to determine important parameters that impact on the mining method selection and demonstrates the calculation of the weighting factors for each selected parameter. This study has been directed to the research of a methodology for the selection of an optimal mining method. Different fuzzy methods are presented as an innovative tool for criteria aggregation in mining decision problems. Two methods of fuzzy multiple criteria decision making are used for selecting the optimal method with which to mine anomaly No. 3 of the Gol-Gohar iron mine. This paper finally presents a comparison of the selection methodologies and further discusses the most appropriate method investigated.

Jan 1, 2004

By B. J. Vorster

AngloGold South Africa region currently consists of twelve gold plants. These plants use a combined total of $20 million of cyanide per annum. Of this, the major portion (60%) is consumed at two Ergo dump retreatment plants. Historically the primary motivation for cyanide control at Ergo has been one of leach/cost optimization. However, more recently, with the increased public awareness of cyanide in the environment, a secondary but increasingly important motivation for control has been to ensure that only the minimum amount of cyanide is added to the process whilst not compromising leach performance. Following a brief overview of the Ergo process, the methodology in determining the amount of cyanide to be added is described. The paper then traces the developments in cyanide control from very basic manual systems to the current automated control system. In line with the increasingly sophisticated control systems, developments also took place in regards to the method of cyanide analysis. The development of these analysers is also discussed. Whilst cyanide is one of the major drivers, if not the major driver of gold dissolution, it cannot be viewed in isolation particularly with respect to the relationship between cyanide and oxygen as ascertained from the Elsner?s well-known equation. Consequently, in order to control cyanide addition, knowledge of the relative cyanide/oxygen profiles is necessary. Various means investigated at Ergo for pulp oxygenation have therefore been included for the sake of completeness. Finally a comparison is made of the control achieved from the current system compared to the original manual system. The knowledge and experience gained at Ergo is now being used to draw up guidelines for the installation and optimization work at the other AngloGold plants. The net effect of this will be reduced cyanide consumption for the region, which also, apart from the obvious economic benefit, translates into a reduced environ-mental risk.

Jan 1, 2001

By Maria das Graças da Silva-Valenzuela, Mathilde Julienne Gisele Champeau Ferreira, Simeão Lopes Ferreira, Francisco Rolando Valenzuela-Díaz

The use of clays to formulate powder coating can improve physical properties, besides a final product with more sustainable characteristics due to the elimination of some additives, which may be substituted for the clay. We investigate the use of a modified smectite clay to formulate powder coating based on polyester resin. Four compositions of incorporated claywere evaluated (0, 4, 7, and 10wt%). Powder coating were prepared in a twin-screw extruder at 105 °C, and characterized by XRD, FTIR and SEM. Tests of flexibility, adhesion and impact strength in accordance to ASTM standards were performed. Diffractograms of the samples showed the characteristic peak of the modified smectite in d(001) * 37°(2h), indicating exfoliation of the clay. Micrographs by SEM showed the presence of lamellar structure for the clay-based powder coating.Mechanical assays were found for all analyzed coatings, indicating that sample containing 7% of clay presents the best performance.

Mar 1, 2018

By F. C. Gennari, D. M. Pasquevich

With the gradual exhaustion of natural rutile, there has been extensive research into its synthesising from lower-grade titanium minerals. The removal of Fe from pseudobrookite (Fe2TiO5) by chlorination was studied, using both isothermal and non-isothermal thermogravimetric measurements. Correlation of the results obtained from element distribution maps, scanning electron microscopy, energy-dispersive X-ray analysis and phases detected by X-ray diffraction in the chlorinated samples showed clearly two associated processes. First, the pseudobrookite particles reacted with chlorine and iron was removed selectively as FeCl3(g), leaving a solid residue rich in the TiO2 phases anatile and rutile, separated from an inner layer of unreacted pseudobrookite by a distinct interphase boundary. Second, chlorine allowed TiCl4(g) to form in the reaction bed, where it removed iron from the Fe2O3 crystals as FeCl3(g) and substituted Ti through a pseudomorphic reaction

Jun 21, 1905

By Charles Frey

TIE fundamental principle of resistance thermometry lies in the determination of temperatures by the measurement of an electrical conductor subjected to various temperatures and the translation of the resultant changes, in ohms, into temperature equivalents. Such resistance measurements can be made with maximum precision by the use of a standard Wheatstone bridge and a reflecting galvanometer of high sensitivity. Under such conditions, results are obtainable that may be accurate within 0.1 or even 0.01 per cent., and the "idiosyncrasies" of heated electrical conductors can be studied with advantage and profit, even if the latter is not of a financial nature. The chief requisites for producing a serviceable -commercial instrument may be enumerated as follows: First, there must be a resistor or "bulb" that can stand the maximum temperature without deterioration and which has a pronounced temperature coefficient. Second, there should be constructed an "even" bridge, having two fixed arms of equal values, in ohms. Third, a rheostat, the maximum resistance of which will be equal to the total change in the resistance of the bulb, between temperature extremes, is required. Fourth, there must be a sensitive galvanometer which is aperiodic, or nearly so. Finally, there should be a fairly steady source of direct current. The general scheme of this type of apparatus, in its simplest form, can be readily understood by reference to Fig. 1. Resistors A and B are constructed of manganin, therlo, or some other resistance wire having a negligible temperature coefficient. The sensitive D'Arsonval galvanometer G has its zero in the center. R is a rheostat and X is a resistor or bulb made of insulated platinum wire, or else of nickel, copper, or some alloy, according to requirements. K is a battery, but a direct-current service line is often used instead, with sufficient ballast in series to properly reduce the current.

Jan 8, 1919

By Bruce Hern

The last 10 years have seen a dramatic increase in the requirements for product coal quality control. This has led to electric utility sulfur scrubbing, metallurgical blast furnace optimization and coal producer blend and yield optimization. To achieve this improved level of control, coal producers are designing facilities that emphasize new technology. New facilities will be designed and existing facilities will be retrofitted with state-of-the-art technology to meet quality control standards that are dictated by the market. The first step in designing for process control requires the identification of those parameters to be controlled and the upsets that can cause variances in the final shipped product quality. The most common parameters that require control are the surface moisture (%), ash (%), pyritic sulfur (%) and gross calorific value (Btu). Total moisture is that moisture that exists on the surface of the particle and is inherent in the particle itself. For the purposes of control, the total moisture is monitored, while surface moisture is controlled. Ash is the inorganic residue remaining after all other constituents are burned away at 75O°C( 1382°F)(ASTM, 1992). Sulfur is the amount of total sulfur that exists either as pyrite (FeS2), inorganic sulfate (FeS04), or organic sulfates (C4H4S) (Leonard, 1979). Currently, pyrite is controlled and total sulfur is monitored. The gross calorific value is the amount of heat produced when a unit quantity of coal is ignited under specified conditions. In this case, a l-g (0.03-oz.) sample of coal is ignited in an isoperibol waterbath and the temperature rise of the water bath is observed. The moisture and ash-free (MAF) Btu is relatively constant for a given seam, resulting in the whole calorific value being a function of the moisture and ash levels (Leonard, 1979).

Jan 1, 1994

By George Hufford

An investigation is made into the applicability of queueing theory to simulating the operation of a large open pit copper mine in the southwestern United States. Actual data from a working mine was used to construct curves for truck loading time, haulage and return time, and dumping times. Known results of investigations of queueing models (Koenigsberg - 1958, Gordon and Newell - 1967, Cabera and Maher - 1973) were used to simulate the actual operation. These did not give acceptable results so commonly used probability distributions were fitted to the actual data. A large computer program known as Q-GERT was used with the various parameters obtained from fitting the curves. Kolmogorov- Smirnov tests were run that showed that this was not satisfactory either. Finally, Q-GERT was used with the actual data from the mine. An appropriate correction factor is then found to apply to the exponential probability distributions tested previously and satisfactory results are obtained.

Jan 1, 1981

By S. A. Sayed, M. N. M. Ahmed, M. A. Doheim

The performance of a 12.7 cm hydrocyclone was investigated by considering the effect of design variables (diameters of the vortex finder and apex) and operating variables (pressure drop and solids content of the feed) at a medium feed solids concentration of mixed minerals. Cut-size was found to be the most important parameter in hydrocyclone design and operation. The effect of feed pressure in reducing hydrocyclone cut-size is less pronounced at medium feed solids concentration with a mixed mineral feed. The choice of vortex finder diameter and apex diameter becomes more sensitive at medium feed solids concentrations. The effect of feed solids concentration in increasing the cut-size becomes less marked at higher concentrations. Predictions of an empirical model were found to be in good agreement with experimental data. Comparison of results obtained from the model with those predicted by theoretically derived models showed the latter to be more promising, with the turbulent two-phase model giving closer agreement with the experimental data

Apr 1, 1995

This paper describes a mobile laboratory developed specifically for nickel prospecting, and which was designed to be operated by sub-professional staff in remote areas independently of established laboratories. An atomic absorption spectrophotometric procedure was used to determine nickel, cobalt, lead, zinc, and copper ID latentIc and sulphIde samples, with a detection limit better than 25 µg/g for all elements. The procedure was applicable to both soil and drill samples and the accuracy of the procedure, which was ±5 per cent relative at the 1,000 µg/g level was sufficient for the preliminary assessment of mineralized samples and the control of drilling operations. The analytical procedure and the means taken to ensure the necessary reproductibility and accuracy are described. One operator can carry out 400 elemental determinations per 8-hr day at an approximate cdst of 6 cents per elemental determination. The results are returned within a single day, a factor which can contribute materially to the efficiency of drilling operations.

Jan 1, 1970