Search Documents

T. R. HARRISON, Washington, D. C. (written discussion). *-Mr. Kowalke shows that a high resistance millivoltmeter is subject to smaller errors, due to change in resistance of the thermocouple to which it is attached, than is a low-resistance instrument. He uses as examples instruments having resistances of 30 and 2 ohms, respectively. At the Bureau of Standards, resistances above 300 ohms would be considered high and 30 ohms rather low. In the tests on calorized-iron thermocouples, a difference between the first and third calibrations of the couples serves to show changes due to the intermediate heat treatment and only under certain conditions would changes in calibrations due to changes in the wire be detected by ,a recalibration after 1 1/2 in. had been cut from the hot-junction end of the couple and the ends rewelded. The calibration of a couple depends only on the thermoelectric prop-erties of that part of the couple which lies within the region of non-uniform temperature, i.e., the temperature gradient; hence, so long as the temperature gradient falls along wires of similar thermoelectric properties no change in the electromotive force is produced by altering the metals of those parts of the circuit that are at uniform temperature. Usually at the cold-junction end of the circuit, copper leads, brass binding posts, manganin resistance coils, and various other materials form part of the circuit, but so long as all are at a uniform temperature (or if for each junction between unlike metals there is a similar opposing junction at the same temperature) no resultant thermoelectromotive force will be produced thereby. Likewise, if a length of several inches at the hot-junction end of the couple is at uniform temperature, it matters not if this section is unlike other parts of the couple, so long as there is good metallic connection and no source of e.m.f. other than thermoelectric is present. Cutting off part of the hot end of the couple within such a region of uni-form temperature would not alter the e.m.f. of the couple.

Jan 12, 1919

By J. V. G. Middleton

The paper gives a comprehensive review of the design considerations which determined the choice of the milling plant, a description of the plant and comment on the operating experience to date. Operating experience will include inter alia a description of the mill liners installed with subsequent changes due to wear patterns, the mill inlet sealing arrangement, steel ball addition, mill outlet sump design, cyclone feed pump liner wear patterns and comment on the efficiency of the linear screens for wood chip and tramp removal. Finally a view on future trends in South African milling practice with respect to type and size of plant.

Jan 1, 1989

By S. McTavish

Since mechanically suitable grinding mills were available in 1908, mill operators have been searching for the best material and design with which to line the mills. These liner systems had to fulfill several criteria. First and foremost they had to last long enough in an operating mill to protect the mill structure from the abrasive wear of the ore and the grinding media. In addition they had to be able to efficiently transfer the energy from the mill to the mill charge in order to facilitate the grinding process. The liners also had to be easily attached to the mill when new and removed from the mill when worn out. The first liners used were generally made of cast white iron, Hadfield manganese, unalloyed high carbon steel and composites of steel and concrete or cemented in flint blocks or natural stone. 1

Jan 1, 1989

By S. B. Patton

A comprehensive approach to the development and organization of an expert system that is designed to assist electricians in diagnosing electrical faults m mining machinery is discussed. The system includes diagnostic, reference, and tutorial programs. The diagnostic portion of the system is based on a causal-reasoning approach which is used to establish a hierarchy of symptoms and the subsequent production rules for identifying component-level failures m the motor-control circuit of a shuttle car. With this approach, conclusions are developed directly from knowledge of the circuit and its behavior (in both working and failure modes) based on first principles, rather than the heuristics of a domain expert. The symptoms and their hierarchical structure an: formulated by creating "what-if" scenarios and performing a qualitative circuit analysis for each fault Techniques for incorporating interactive graphical displays of the circuit schematic into the diagnostic portion of the system are also presented. Supportive computer programs that provide' reference material and tutorials on the circuit are also described.

Jan 1, 1989

By E. C. IBBOTSON

THIS process was reported upon by the Canadian Commission in 1904, and much detailed information was also given in a paper by Chief Engineer V. Engelhardt.1 Believing that some of the latest particulars of the process will be of interest, I submit the following data. At Gysinge in Sweden during the year ending May 31, 1906, from a fixed furnace giving 1 ton (2,240 lb.) of steel per tap, there were produced 950 tons of tool-steel and special steel ingots. . In carbon and iron tool-steels all the usual tempers were made. The bulk of this steel was made from charges composed of about 80 per cent of Swedish white pig-iron and 20 per cent. of steel-scrap. The percentage of carbon was regulated by the addition of briquettes. Other charges were made from Swedish white iron and steel-scrap. The average time taken per charge, for the year, when adding briquettes, was 7* hr., and the electric energy consumed was 1,128 units (kilowatt-hours) per ton. The average time per charge for white-iron and scrap charges was 5.5 hr., and the electric energy consumed was 886 units per ton. These consumptions include all time and energy lost from various causes, such as bad water-supply, ice, etc. It is quite ordinary practice to complete the charges with briquettes in 6.5 hr., and without briquettes in 5 hr., as shown by the following typical charges White pig-iron, 1,457; steel-scrap, 439; briquettes, 220; ferrosilicon (50 per cent. of silicon), 17 ; ferromanganese (80 per cent. of manganese), 15 lb. ; and aluminum, 1 oz.=

Nov 1, 1906

In the Philippines, where distances are spoken of in terms off fight time, the Sipalay copper mines are two flight hours southeast of Manila on the island of Negros. After landing at the airport in Bacolod, it is then 170 km (106 milers) by surface transportation to Marinduque Mining and Industrial Corp.'s expanding copper operation. While copper deposits were discovered in the area in 1936-and one mine, the Binulig, began operations soon after-it wasn't until 1956 that stripping at Sipalay and construction of a 4000-t/d (4400-stpd) mill began. The mill went into operation in May 1957, and the first shipment of copper concentrate was made three months later.

Jan 8, 1978

By P. R. Swann, J. G. Parr

Quenched structures were studied in alloys containing up to 12.5 pct cobalt. The subsequent decomposition of a 10 pct cobalt retained-ß phase alloy was investigated using metallographic and X-ray diffraction methods. Hardness measurements also were made during the decomposition process. Precipitation of Ti2Co is by nucleation and growth; and an activation energy of 50,000 cal per mole was determined. The values of the coefficient ß suggest that the precipitate is pearlitic at temperatures between 450 and 475°C, and spheroidal between 500 and 525°C. THIS paper describes part of a series of invesligations into phase transformations in binary alloys of titanium with transition elements. The general approach is similar to that taken in work on titanium-iron and titanium-nickel alloys.' Previous investigators'' have established the titanium-rich end of the titanium-cobalt phase diagram, reproduced in Fig. 1. Orrell and Fontana' showed that alloys containing more than about 6 pct" cobalt quenched from the ß range, produced 100 pcl retained-p phase. The isothermal decomposition of alloys containing between 0.8 pct Co and 15.5 pct CO was investigated by the same workers in the temperature range 650 to 1000°C. They reported that these alloys transformed into a or Ti,Co depending on the cobalt content, but no quantitative data were given. In the work to be described a series of alloys containing 0.8 pct Co to 12.5 pct Co was examined in the quenched condition. The 10 pct Co alloy (the lowest cobalt content to retain 100 pct ß on quenching) was selected for further work on the tempering kinetics of the ß decomposition. Experimental Procedure Since our own melting equipment was not installed at the outset of this work, the Physical Metallurgy Division of the Department of Mines and Technical Surveys (Ottawa, Canada) prepared the alloys. These were made of Japanese sponge, (which when melted had a value of 103 DPH, using a 1-kg load), and electrolytically prepared cobalt. The al- loys, made up to contain 0.8, 1.6, 3.3, 5.8, 8.3, 10.0 and 12.5 pct Co, were homogenized by swaging into rods at 900°C. Filings were taken from the rods, and any iron chips from the file were separated magnetically. Size fractions of both plus and minus 200 mesh (about 75p) were shown by their constitution, after annealing just below the eutectoid temperature, to contain the same cobalt content. Consequently, it was permissible to use the —200-mesh fraction, knowing it to be representative of the rod composition. Quenching in argon was carried out in a newly designed furnace, whose features include (1) an Inconel furnace tube, (2) a positive pressure of argon maintained at all times in the furnace—even when a sample is removed or inserted. The furnace is shown in Fig. 2 and is described in the Appendix. The tempering processes were carried out on powder samples sealed in evacuated quartz capsules. Since the highest tempering temperature was 525OC, no protection against reaction with the quartz was necessary. (Tests were made on filings of iodide titanium and showed no hardness increase after equivalent heat-treatments.) A thermocouple was attached to the capsule, which was heated to the

Jan 1, 1959

By Mark L. Blanford, Roger M. Zimmerman

INTRODUCTION Volcanic tuffs on and adjacent to the Nevada Test Site (NTS) are being considered by the Department of Energy (DOE) for the possible geo- logic disposal of high-level radioactive wastes. The Nevada Nuclear Waste Storage Investigations (NNWSI) project was established in 1977 to evaluate such disposal. Sandia National Laboratories (SNL), one of the participants in the NNWSI project, has as one of its responsibilities the development of a rock mechanics program for the Nevada site. SNL conducted three small-diameter heater experiments in welded and nonwelded tuffs in G-Tunnel on the NTS, to investigate the thermal (heat transfer) and hydrothermal (thermal- induced water migration) behavior as part of the rock mechanics program. These two aspects were investigated to increase knowledge about the behavior of tuff so that predictive capabilities are available for use by repository designers, waste-package designers, and performance analysts. Also, knowledge of the behavior of the tuff is invaluable for planning and designing future in situ experiments at Yucca Mountain, the candidate site for the repository. The evaluations of these three experiments is the subject of this paper. Designers, analysts, and experimenters are seeking a better understanding of the behavior of tuffs under the influence of thermal loads expected from radioactive-waste storage, because of two physical features peculiar to tuffs. First, tuffs are inherently porous because of the manner in which they are deposited (Smith, 1960). Tuffs utilized in G-Tunnel testing have porosities ranging from 15 to 46%, which cover the ranges of expected porosities in the target horizon at Yucca Mountain. It has been established that the G-Tunnel tuffs have similar bulk, thermal, and mechanical material properties to those at Yucca Mountain (Zimmerman et al., 1984), thus, G-Tunnel testing can be used to evaluate the effects of porosity on the thermal and mechanical behavior. The second feature is that tuffs above the water table contain pore water that influences the thermal properties of the rock; displacement of the water must be accounted for in repository designs and analyses. For example, G-Tunnel tuffs, located some 600 m above the static water level, have saturations in excess of 60%. Similar percentages are expected at the target horizon in Yucca Mountain (Zimmerman et al., 1984). The presence of and the removal of the pore water affects the thermal behavior of the tuffs, and these three experiments were designed first to determine the phenomenological behavior and then assess influences on predictive capabilities. The focus in this paper is to present the results and evaluations of the experiments as they apply to improving predictive capabilities. The thermal aspects are emphasized by comparing the measured temperatures (in and around heater emplacement holes) with calculations of predicted temperatures using numerical models, so that the effects of significant parameters can be evaluated and integrated into future predictive models. Observation of the hydrothermal aspects is needed to assess the effects of loss of pore water and subsequent migrations on the temperature fields during the heating, and also to define the expected environment in the vicinity of the outer metallic surface around the waste. The metallic boundary can be either the outer shell of the waste package system, which is the main engineered barrier for waste containment, or the borehole liner. A final decision has not been made as yet about the necessity for lining boreholes; thus, the emphasis is on predicting the characteristics of the environment around the outer metallic surface. Two aspects that limit the scope of this paper are (1) the experiments were performed at a smaller than canister scale for the purpose of

Jan 1, 1986

By John C. Machisak

INJURY experience and employment data at all metal mines in the United States and Alaska are presented in this Information Circular for the calendar year 1958. This publication covers the metal mining industries, and contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. These operations report injury and employment information annually to the Bureau of Mines on a voluntary basis. The Bureau is authorized to make requests for such data, and the information submitted contributes immeasurably to the promotion of safety in the metal mining industry. Every effort has been made to make the annual canvass as complete as possible. This publication contains, along with production and development workers, the office employees at the mine location. The metal mines identified in this publication are classified according to the mineral ores mined; that is, copper, iron, lead-zinc, gold-silver lode, gold placer, and miscellaneous metals.

Jan 1, 1962

By W. N. Roberts

Hadfielcl steel has been studied by transmission electron microscopy to determine the microsl.rtic-ture of the cold-worked material, which has been a subject of controversy for many years. The presence of fcc deformation twins in specimens deformed in tension, by hamnzering, and by explosive -shock loading at room temperature lzas been established by electron diffraction. No evidence of a mar tensite was detected in any of the speciwens. Small amounts of E martensite were idenLified in the hamnleved specimens. DESPITE numerous researches on Hadfield steel since its discovery in 1882, there is still disagreement on the nature of transformations in the cold-worked material. Collette el al.,' using X-ray and electron diffraction, have found evidence for stacking faults, E martensite, and a martensite in Hadfield steel deformed in tension at room temperature. Nishiyama and Simizu,' using electron microscopy, have found stacking faults and E martensite in hammered Hadfield steel. White and Honeycombe have concluded from X-ray diffraction that Hadfield steel remains fully austenitic even after severe cold work at -196 Previous work by the author, indicating the presence of a, martensite in deformed Hadfield steel, was in error due to a faulty interpretation of the electron-diffraction patterns. Various workers,5'7 over the years, have speculated on the presence of deformation twins in Hadfield steel, largely from such circumstantial evidence as the persistence of slip bands with repeated polishing and etching, the presence of serrations in the stress-strain curve, and the absence of evidence of a martensite by X-ray measurements. The advent of electron-transmission microscopy and se- lected-area diffraction has made possible the positive identification of fine deformation twinning. PROCEDURE For tensile tests, standard ASTM specimens of 2-in. gage length, ground from 0.12-in. Hadfield steel sheet, were solution-treated at 1050°C for 30 min in a salt bath, to avoid decarburization, and water-quenched. The grain size was about 0.01 sq mm. Chemical analysis of the steel after heat

Jan 1, 1964

By G. H. Thomas, M. C. O’Riordan, S. Rae

INTRODUCTION The British mining industry comprises 228 nationalised coal mines producing some 113 million tonnes of deep mined coal and employing 242,600 persons of whom 185,200 work below ground. There are in addition 174 small privately-owned coal mines employing 1500 persons underground and producing 1.5 million tones of coal. In the non-coal sector there are 108 privately-owned mines producing some 20 different minerals, including tin, wolfram, fluorspar, potash, rock salt, china clay, ball clay and fireclay. There are currently 4,100 persons employed in these mines of whom 2,346 are employed below ground. One mine producing potash employs 870 persons of whom 465 are underground workers. Since 1975 all matters relating to the health and safety of persons at work and of the general public who are exposed to industrial hazards have come within the purview of the Health and Safety Executive (HSE). The Mines and Quarries Inspectorate (MQI) is a constituent part of that organisation and enforces legislation applicable to all mines and quarries. The National Radiological Protection Board (NRPB) is a statutory and independent body that was established in 1970 to advance knowledge and provide information and advice about radiological protection. The NRPB has an agency agreement with HSE to provide advice and services relating to radiological protection, including protection against exposure to radon decay products in mines. There are as yet no statutory requirements controlling exposure to this source of radiation in Britain. Investigations for the presence of radon in British coal mines were begun in the mid 195Os. The concentrations found were of low order, typically around 2 pCi/l (Duggan et al., 1968). This was not surprising since big coal mines are well ventilated to control methane and airborne dust and it is now generally accepted that radon and its decay products do not constitute a health hazard in British coal mines. At one or two small mines where igneous intrusions were in close proximity to the coal workings, slightly higher readings were recorded. The MQI then commissioned NRPB to make investigations at metalliferous mines and in these much higher readings were detected. It was later agreed that the NRPB should undertake a survey of all non-coal mines in Britain to establish the extent of the problem. This survey was conducted mainly in 1973, (Strong et al.,1975) and follow-up surveys at various mines have since been conducted by the MQI. These investigations revealed that radon readings could be high in mines producing tin, haematite and fluorspar. Some small mines working other minerals in the same localities also showed high readings. More recently owners have been making environmental measurements at mines where there was some cause for concern. LEGISLATION AND RADIATION STANDARDS As a result of the survey work for MQI the Board in 1975 recommended an occupational limit of 4 WLM in a year from radon decay products together with a programme of radiological supervision (Strong et al., 1975). The MQI accepted the recommendation and advised employers and employees that the 4 WLM limit should be adopted. The limit corresponds to a concentration of 0.3 WL, equivalent to 30 pCi/l of radon-222 in equilibrium with the decay products, and was in accordance with an earlier recommendation by the International Commission on Radiological Protection (ICRP, 1959). ICRP recommendations are usually endorsed in Britain. It was recognised that some years would probably be required to achieve general compliance, and this is proving to be the case. Some confusion has been caused in Britain by the conflict between successive Euratom Directives on this and other standards of safety. As relative newcomers to the Community, we were not affected by earlier Directives, but the situation is different now. In 1959, the Commission of the European Communities provisionally recommended a maximum permissible concentration for radon-222 and daughters of 3 x 10-7 µCi/cm3, which corresponds to 300 pCi/l (CEC, 1959). The number was affirmed in 1962 (CEC, 1962) and reaffirmed in 1966 (CEC, 1966) but without any specification of the state of equilibrium. In 1976, the CEC again recommended 300 pCi/l, but on this occasion, the daughters were assumed to be present in the same quantities as in unfiltered air (CEC, 1976): this implies 40 WLM a year in poorly-ventilated mines. The formula is repeated in the latest version of the Directive (CEC, 1980), but the value is now said to be an interim one because it might not ensure compliance with the appropriate dose limit. ICRP (1955) recommended 300 pCi/l in equilibrium with the decay products in 1955 and reduced this value to 30 pCi/l for unfiltered air in 1959 (ICRP, 1959), endorsed it for equilibrium conditions in 1976 (ICRP, 1976), and held to it until 1980: these values imply respectively 40 and 4 WLM a year. The recent recommendation of the ICRP (1980) that the annual limit of intake for the decay products should be 0.02 J in a year corresponds to 5 WLM, but there is a rider that reduction should be made for exposure to gamma rays and long-lived airborne radioactivity. An allowance of 20% is suggested for uranium mines, implying 4 WLM a year for the decay products. The

Jan 1, 1981

By Dae Jin Ha

Sticking phenomenon occurring during hot rolling of two STS 430JlL ferritic stainless steels was analyzed by hot-rolling simulation tests. The sticking started from the initial nucleation stage in which the rolled materials were stuck onto the roll specimen surface, proceeded to the growth stage in which stuck fragments grew further, and reached the saturation stage. The modified 430JlL steel had a smaller number of sticking nucleation sites and slower growth rate than the conventional 430JlL steel because of higher high temperature hardness, thereby leading to less serious sticking. When the simulation test was conducted at 1070 °c, Cr oxides were formed on the surface of the rolled materials, and thus the sticking was drastically reduced because of the increased surface hardness of the rolled materials. In order to prevent the sticking, high-temperature properties of the rolled materials should be enhanced when rolled at 900°C or 1000 °C, and rolling conditions and alloying compositions, under which the oxide formation was promoted, were more important than high-temperature properties when rolled at higher temperatures than 1000 oC.

Jan 1, 2008

By Robert P. Harrison, Marie-Christine Patoinel, Kristian E. Waters

This paper describes a collaboration between McGill University and Hatch Ltd. to expose undergraduate students to real-world industrial projects. As part of the final-year design course, the students receive a detailed lecture on Scale-Up of New Technologies', including seven case studies drawn from over fifty years of full-scale industrial projects. The students are taught the basic concepts of scale-up, including the limits of pure theory and the need for empiricism. Insights from real scale-up failures and successes are fictionalized as Projects A, B, C, etc. The students are then asked to identify the guiding principles that can be distilled from these case studies.

Jan 1, 2011

By Jian Ye

Recycling of aluminum scrap, such as Used Beverage Container (UBC) scrap is steadily increasing. In secondary remelting of such scrap, it is a common practice to use protective molten salt cover. An appropriate salt protects metal from oxidation, promotes coalescence of the suspended metal droplets, and separates clean metal from the oxide contamination. The molten salt also reacts with metal. This causes metal loss and change of resulting metal composition. In this paper, role of molten salt fluxes in melting of UBC scrap is discussed, and selection criteria for molten salt are provided.

Jan 1, 1995

By cheng Peng-fei, TANG Hai-yan, guo Xiao-chen, LI Jing-she, Liang Yong-cang, Zhao Baojun

The origin and evolution of non-metallic inclusions for Al-killed casing steel during EAF-LFVD- CC process were studied by industrial tracer experiments. The formations of Al2O3 and MgO·Al2O3 micro- and macro-inclusions from ladle slag were analyzed by theoretical calculations. The results show that micro-inclusions were formed during deoxidation and temperature decreasing in the process of casting, most of the macro-inclusions come from entrapped ladle and mold slags. In addition, most of the Al2O3 formed were modified into 12CaO·7Al2O3 and 3CaO·Al2O3 inclusions which are liquid at steelmaking temperature. MnS cannot be fully modified to CaS and it was only wrapped outside the alumina or calcium aluminate in the form of (Ca,Mn)S with the amount of Ca-Si wire fed during the test.

Jan 1, 2016

By Sheng-ping He, Ya-bing Zhang, Qian Wang, Kun-peng Xu

A mass of Al2O3 tends to form during the continuous casting process of high manganese high aluminum steel, and the properties of mould flux and the quality of slab are seriously affected. The dissolution rate of Al2O3 into the CaO–SiO2–MgO–Al2O3–F−−Na2O−Li2O−BaO−B2O3 slag system has been investigated at 1573 K by employing rotating cylinder method. This paper focuses on the effect of Na2O, Li2O, B2O3, F−, Al2O3 contents and (CaO+BaO)/(Al2O3+SiO2) ratio on the dissolution rate. Experimental results show that the dissolution rate increases with increasing Na2O, Li2O, B2O3 contents and decreasing Al2O3 content, among which Li2O has the greatest effect on increasing dissolution rate; the dissolution rate increases with increasing F− content in slag A-1, but decreases with that in slag A-2; the dissolution rate increases with (CaO+BaO)/(Al2O3+SiO2) ratio within the range from 0.91 to 1.31. The dissolution rate of Al2O3 into molten flux is mainly affected by the viscosity of the molten flux and the thermodynamic driving force.

Mar 1, 2018

By Mike Johnson, Greg Andrews, Niels Verbaan, Ernesto Bourricaudy, David Dreisinger

Search Minerals has developed a Direct Extraction Process for recovery of rare earths from the Foxtrot and Deep Fox deposits in Labrador Canada. The process includes crushing, acid treatment, water leaching, impurity removal, precipitation of an intermediate rare earth product and finally re fining of the intermediate product to produce a high purity mixed rare earth oxide (*99% total rare each oxides). The Direct Extraction Process has been validated in an extensive demonstration pilot plant program at SGS Minerals. A total of 3 tonnes of material was processed to produce final mixed rare earth product. The results of the demonstration pilot plant program are reported.

Mar 1, 2018

By A Winchester, D Grant

The massive 1100 Orebody in Mount IsaÆs X41 Copper Mine has been extracted over the last 40 years form north to south utilising sublevel open stoping methods.De velopment has continually stepped ahead of production to provide access to new primary stoping blocks. The remaining secondary pillars contain stopes with one, two or three fill mass exposures and were constrained by access requirements and stope extraction turnaround time.The remaining southern mining areas consist of large 40 m wide by 300 to 400 m long east-west transverse pillars that have been left to provide access for ventilation and service requirements. Three large transverse cross-cuts or transverse pillars û 4180 x/c, 4010 x/c and the Panel pillar now remain. The 4180 x/c was the last major transverse pillar to be successfully broken.This transverse pillar is being extracted in a retreating sequence, creating 3SLOS stopes due to the surrounding backfilled stopes.In recent years the extraction of the first, and most critical, stopes in the transverse pillars have resulted in large changes to the induced stress field. This paper describes the extraction of the 1.1 million tonne stope P418 in the 4180 x/c pillar.T echnical challenges that were faced and how they were overcome to allow for the successful extraction of the stope are described.Critical to the success of the P418 stope extraction were the rehabilitation methodology used; extraction strategy modifications to address deteriorating ground; mass firings with multiple directional changes; managing the exposure of backfill of variable strengths; and geotechnical monitoring prior to, during and after extraction.

Jan 1, 2005

By Charlie Vaught, Bill Wiehagen, Lynn Rethi, Pamela Kidd, Lisa Steiner, Ted Scharf, Henry Cole, Kathleen Kowalski

The most hazardous work environments share one feature in common: constant change. Many different, but constantly changing hazards are found in agriculture, construction, mining, and transport. This dynamic feature of work-place hazards varies by: (1) degree of control, (2) predictability, (3) visibility, (4) movement, and (5) degree of speed and force. In some cases the actions of the dynamic hazards are required for production to take place, and in many cases,

By G P. Bates

The rationale for the design of the Emergency Egress (escape andentrapment) strategy for one underground metal mine has beenpreviously described (Brake, 1999). Two of the key conclusionsfor this mine, which is equipped with 30 minute oxygen-generating self-contained self-rescuers (SCSR), were the need to ensure no person is ever more than 750 m from an emergency refuge station (ERS) and that it could take up to eight hours to rescue workers from undergroundå. These conclusions were based on a number of considerations including the non-availability of a credible, æpersonalÆ entrapment procedure at the workplace, the duration of self-contained self-rescuers when used for travel, the need for rapid æclearingÆ of mine personnel to effectively and safely target mine search and rescue resources and the maximum time to either put a fire out, or to rescue affected personnel. As there is no Australian standard for refuge stationsç (or for self-rescuers), this paper follows with guidelines for the location and specification of both fixed (permanent) and relocatable Emergency Refuge Stations (ERSs) that may be applicable to other underground Australian metal mines.

Jan 1, 1999