Search Documents

By J. R. Cahoon, W. V. Youdelis

FOR the diffusion of copper in silver-rich alloys, there have been only two previous investigations, that of Seith and Peretti in 1936, and that of Sawatzky and Jaumot2 in 1957. Seith and Peretti obtained a value of 24.8 keal per g-atom for the activation energy of diffusion whereas Sawatzky and Jaumot obtained a value of 46.1 keal per g-atom. Admittedly, Seith and Peretti used relatively high concentrations of 2 at. pet Cu and polycrystalline diffusion couples, while Sawatzky and Jaumot investigated tracer diffusion in single crystals of silver. The difference in the results, however, seems too large to attribute solely to solute concentration, as a change of over 20 keal per g-atom in the activation energy suggests a change in the mechanism of diffusion. Therefore, in the present investigation the diffusion coefficient for copper in polycrystalline Ag-2 at, pet Cu alloy is re-established using conventional sandwich-type diffusion couples and electron-probe microanalyses, and the results are compared with those of the previous studies. The diffusion couples were prepared from high-purity silver (99.999 pet) and high-purity copper (99.999 pet). The silver disks, 1/4 in. long and 4 in. in diam, were machined from an ingot which had been solidified in a dynamic vacuum of 10-3 mm of Hg to eliminate oxygen absorption which otherwise would result in copper oxide precipitation in the weld zone. The alloy disks of similar dimensions were machined from an alloy ingot (nominal composition 2 at. pet Cu) which had been unidirectionally solidified to obtain a predictable solute concentration,3 and homogenized for 1 week at 800°C. Sandwich diffusion couples were made by pressure welding an alloy disk between two silver disks in an induction heating coil. The couples were diffusion-annealed at temperatures of 800°, 756°, 699°, and 630°C in tube furnaces in which the temperature was controlled to better than ± l°C. The diffusion couples were examined metallographically for weld defects, and couples showing even minute defects at the weld interfaces were rejected. Concentration penetration curves were established using an A.R.L. Microprobe analyzer. CuKO radiation was counted and converted to concentration using 0.5 and 1.0 wt pet Cu chemically analyzed standards. Initially, four continuous profiles were obtained, and averaged to obtain the final diffusion curve. The initial analysis was performed commercially and the welds were not located with respect to the profile. Therefore, the results were rechecked by the authors using the Mellon Institute A.R.L. probe. In the latter case, concentrations were obtained at 10-µ steps for four different traverses, and then averaged to obtain

Jan 1, 1968

Boiler-Room Economy "Establishing and Maintaining Boiler-room Economy" is the title of a paper presented before the Ohio Society of Mechanical Electrical and Steam Engineers by Geo. H. Gibson, of which the following is an excerpt: Boiler-room economy depends less upon equipment than upon operation, i.e., it depends largely upon the condition in which the apparatus is maintained and how it is used. A given boiler may operate this week with an efficiency of 78 per cent., and next week with an efficiency of 65 per cent., while using the same fuel and developing the same rating. If there are variations ii; character of fuel and in load and other factors, the falling-off may be even greater, possibly to less than 60 per cent. The steam produced may cost twice as much per 1,000 lb. at one time as at another. Most steam plant managers know from their own experience that these statements are not exaggerated. It does not take much of a plant to run up a coal bill of $5,000 per year, many "spend $10,000 for coal, and fuel bills of $50,000, $100,000, or $200,000 per annum are not uncommon. As it call be shown in the majority of these plants that 10 per cent. of this amount may be saved, and in large numbers of them 25 per cent., while in some the expenditure can be cut in half, there is no disputing that we have here a subject worthy of attention. In the production of steam the greatest variable is the human factor. Before we can pass judgment, however, we must first have standards. This implies accurate quantitative knowledge of fuel consumption and steam production. We must measure the output and know how much the steam costs per thousand pounds, and how many pounds of steam are obtained from a pound of coal. We can then begin to analyze the problem, and find where and how methods and conditions can be improved, and how much. Many favor buying coal on a B. t. u. basis. This is advisable where the amount purchased warrants the considerable expense involved in systematically gathering samples that: are. truly representative and in having analyses made, of every carload. Coal analyses, combined with. an honest endeavor on the part of the miner to ship good coal, should insure the receipt of the heat units paid for. , It often happens, however, that the coal which is cheapest on a B.t.u. basis is not the cheapest or most suitable for producing steam, because of peculiarities of the plant in which it is to be burned, or conversely, the fuel which furnishes cheap B.t.u. may require special methods or equipment for its economic utilization.

Jan 2, 1916

By R. S. French, W. R. Hibbard

FOR tensile deformation, if the stress value is defined by the ratio of the load to the actual area, and the strain value by the natural logarithm of the ratio of the immediate length to the original gauge length of the sample, the resulting data when plotted with logarithmic coordinates result in a linear relation extending from the initial plastic yielding through the maximum load and in some cases, such as for copper and brass, to fracture'.'. The normal form of the curve, therefore, is a parabola, satisfying the following equation: S = Kem [1] where S and e represent true stress and strain, K is a constant, and m is a coefficient evaluating the slope of the curve and designated therefore as the strain hardening coefficient. Hollomon² has reported that this coefficient is a function of the yield strength as effected by grain size in alpha brass, and the carbon content and heat treatment of steel. In the case of steel, the value of the proportionality constant is a function of the carbon content. It was further shown in that paper2 and also by Low and Prater -hat, if the power relation between stress and strain remains valid, the strain hardening coefficient m, is equal to the strain at the maximum or necking load. Thus, an added significant feature is that this coefficient may serve as an index of the capacity for deformation prior to localized necking and subsequent fracture, e.g. drawability. The constant K may be defined as the strength of the material at unit strain. Together the K constant and the m coefficient describe an alloy's physical properties as far as strength and ductility are concerned for a particular yield strength and, in the case of steel, a particular carbon content. The work of Lacy and Gensamer4 gives data on alloy ferrites from which very close estimates of the strength of ternary and higher iron alloys have been made. It was the purpose of this investigation to develop similar data for commercial copper base alpha solid solution alloys. Preparation of Specimens Commercial binary alloys of copper with aluminum, beryllium, cadmium, nickel, silicon, tin and zinc were investigated. In addition, laboratory castings were made of a 1 pct silicon alloy and a 2 pct aluminum alloy to complete these particular series. Two types of copper were used, oxygen free OFHC and tough pitch FC. The analyses of these alloys are shown in table I. Standard ASTM sheet tensile specimens were used to determine the usual physical properties of each alloy and to obtain stress data at strains from 0.0005 to 0.01. Small (1/4 in. x 3 in. x tk.) samples

Jan 1, 1951

By W. R. Ernst

A method for the removal of nickel and vanadium contaminants from spent HDS catalysts involves pretreating the catalyst with H2S followed by the extraction of the metals with an acidic solution of ferric ion. The ferric ion solution alone removes significant amounts of active ingredients cobalt and molybdenum; however, after pretreating the catalyst with H2S, the extraction becomes more selective for the removal of Ni and V.

Jan 1, 1986

By Ellis S. Hertzog

The relatively large amount of phosphorous occurring in many iron ores limits their usefulness aid sometimes renders them valueless under present conditions of nip-iron manufacture. A practical method for removing the phosphorus would be valuable to the iron and steel industry. Gravity concentration has been of little value as far as the removal of phosphorous is concerned, because the compounds of this element are, as a rule, disseminated very finely. Removal of the phosphorous by leaching is not a new idea and has been the subject of some investigation,3,4/ out for data :lave been published. W.R. Crane published analyse of various ore bodies in the Birmingham ham district. The hard or unleached ores a .re much higher in phosphorous than the Soft, leached ores along the outcrops. This fact indicates that as mild a leaching agent as water removes phosphorus effectively if enough time is allowed for it to react. As the forms in which phosphorous occurs in the iron ores are important in the consideration of any leaching operation, much time was expended in devising a method for determining them. According to Professor McVey, University of Alabama, the phosphorous-bearing minerals in the red iron ores of Alabama have not been positively identified by any microscopic methods.

Jan 1, 1935

By Ellis S. Hertzog

[The relatively large amount of phosphorous occurring in many iron ores limits their usefulness mid sometimes renders them valueless under present conditions of pig-iron manufacture. A practical method for removing the phosphorus would be valuable to the iron and steel industry. Gravity concentration has been of little value as far as the removal it of phosphorous is concerned, because the compounds of this element are, as a rule, disseminated very finely. Removal of the phosphorous by leaching is not a new idea and has been the subject of some investigation,3,4/ but few data have been published. W. R. Crane published analyses of various ore bodies in the Birmingham district. The hard or unleached ores are much higher or in phosphorus than the soft, leached ores along the outcrops. Tips fact indicates that as mild a leaching agent as water removes phosphorus effectively if enough time is allowed for it to react.]

Jan 1, 1935

By E. S. Rowland, J. Welchner, R. H Marshall

This paper presents results on an extension into the realm of high-carbon steels of some work recently published1 on the effects of time at temperature, quenching temperature and prior structure on the hardenability of one 0.20 and four 0.40 per cent carbon alloy steels. It was shown at that time that unless the conditions of time, temperature and prior structure are substantially the same in performing the hardenability test as in conducting hardening of parts in production, the correlation of hardenability information with the hardness and properties of production parts is often not of satisfactory accuracy. The general effects of these variables on the austenitic grain size, distribution of excess carbides and critical cooling rate have been known for many years and one or more have been investigated by Shepherd,2,3 Davenport and Bain,4 Digges,5,6 Digges and Jordan,' Post and associates8 and Roberts and Mehl,9 to mention only a few. There has been no systematic investigation, however, into the quantitative variations produced on the hardenability of commercial high-carbon steels by changes in these factors of time, temperature and prior structure. Procedure A plain carbon hypereutectoid steel, S.A.E. 52100 and Graph-Mo, a molybdenum-bearing high-carbon steel containing some graphite, were chosen for this investigation. The chemical analyses of these electric-furnace steels are given in Table I. The procedure used was exactly that reported previously,' hence the details will not be repeated here. Normalized (165o°F.) and spheroidized prior structures were utilized on all steels with hot-rolled and quenched (I600°F. oil) prior conditions added for the plain carbon steel. The end-quench test developed by Jominy10 was sclected for use in this investigation and, with the noted exceptions, the American Society for Testing Materials standard procedure was followed. The effect of time at temperature was examined at intervals of o, 10 and 40 min. and 4 hr., and a few 16-hr. tests were run. Salt-bath heating of the specimens was employed to control and minimize the

Jan 1, 1944

By James R. Dunn

The nature of water and clay in carbonate rocks is currently being investigated at Rensselaer Polytechnic Institute by various thermal and sorption techniques. Two basic concepts 'led to the present research. (1) To explain the expansion and contraction on wetting and drying of some unsound argillaceous carbonate rocks, it was postulated that the pore space around each clay particle is such that when water is sorbed by the clay, force is exerted against the pore walls. (2) The clays in expansive rocks are rejected from the growing dolomite crystals during their growth, and form a more or less connected network, thereby becoming "wettable," or available to water. New quantitative cold differential-thermal-analysis (electrocalorimetric) equipment was designed and constructed to check the "limited space" and "wettable clay" concepts and to determine the thermal nature of the transition of water to ice in rocks. This DTA equipment can detect the release of heat in freezing of less than 0.001 per cent water in a rock. Twenty-three rock cores (nine sound and fourteen unsound) and 4 procelain cylinders for standards were studied. In the nine sound rocks and in all the procelain cylinders, the rapid freezing of from 50 to 100 per cent of the water was readily detectable after 7 to 10° C of supercooling. No further freezing could be detected to -20° C. However, in eleven of the fourteen unsound rocks, no freezing was detected to as low as -40° C; in the other three, less than 50 per cent of the water froze. As a check of the DTA measurements, adsorption isotherms were determined for all materials. Calculations of theoretical freezing points for sorbed water again demonstrated that the least sound rocks had the most nonfreezable water. "Frost" sensitivity in these carbonate rocks is, therefore, probably not the result of the force of expansion of water to ice. The disruptive force is believed to result from expansion of sorbed, ordered water on clay surfaces. The relationship between the unfilled rock pores after 24-hour water saturation and the water sorbed at 85 per cent humidity at 30° C (i.e., the theoretical nonfreezable water delineates the sound and unsound carbonate rocks.

Jan 1, 1966

By R. H. Marshall, J. Welchner, E. S. Rowland

This paper presents results on an extension into the realm of high-carbon steels of some work recently published1 on the effects of time at temperature, quenching temperature and prior structure on the hardenability of one 0.20 and four 0.40 per cent carbon alloy steels. It was shown at that time that unless the conditions of time, temperature and prior structure are substantially the same in performing the hardenability test as in conducting hardening of parts in production, the correlation of hardenability information with the hardness and properties of production parts is often not of satisfactory accuracy. The general effects of these variables on the austenitic grain size, distribution of excess carbides and critical cooling rate have been known for many years and one or more have been investigated by Shepherd,2,3 Davenport and Bain,4 Digges,5,6 Digges and Jordan,' Post and associates8 and Roberts and Mehl,9 to mention only a few. There has been no systematic investigation, however, into the quantitative variations produced on the hardenability of commercial high-carbon steels by changes in these factors of time, temperature and prior structure. Procedure A plain carbon hypereutectoid steel, S.A.E. 52100 and Graph-Mo, a molybdenum-bearing high-carbon steel containing some graphite, were chosen for this investigation. The chemical analyses of these electric-furnace steels are given in Table I. The procedure used was exactly that reported previously,' hence the details will not be repeated here. Normalized (165o°F.) and spheroidized prior structures were utilized on all steels with hot-rolled and quenched (I600°F. oil) prior conditions added for the plain carbon steel. The end-quench test developed by Jominy10 was sclected for use in this investigation and, with the noted exceptions, the American Society for Testing Materials standard procedure was followed. The effect of time at temperature was examined at intervals of o, 10 and 40 min. and 4 hr., and a few 16-hr. tests were run. Salt-bath heating of the specimens was employed to control and minimize the

Jan 1, 1944

This paper reviews the history of refractory materials, highlights the development of refractory technology over the years, draws attention to the technology behind these materials, and comments on future developments in this field. By walking the path with refractory materials, from their initial uses in BC times, to the composite materials that are used nowadays, and the nanotechnology developments that are currently taking place in this field, the reader will come to agree that refractory materials are indeed very ?cool?! Keywords: refractory materials; bricks; monolithic materials.

Jan 1, 2008

By Avi Nanda, Robert Brandt, Alex Piatkiewicz, David M. Jones

In 2010 the United States Environmental Protection Agency (UESPA) revised the National Ambient Air Quality Standards (NAAQS) by lowering the permissible value to a 1-hour average SO2 concentration of 75 ppb. In 2012, the USEPA designated the Miami area as non-attaining for the new SO2 NAAQS. A number of options were studied to assist in bringing the Miami smelter into attainment with the new standard. The chosen solution included: Installation of a large tertiary hooding system over the converter aisle; Hooding of the anode vessels and treatment of the anode gas in a baghouse; Installation of a large 2,325,212 Nm3/hr caustic scrubber to treat the captured converter fugitives and anode off-gases; Installation of a secondary ESP for the tapping fugitive off-gas treatment system; and the continuous scrubbing of all acid plant tail stack gases. The modifications have reduced smelter SO2 emissions by 85%, achieving a world class SO2 stack emissions rate of 0.45 kg of SO2/tonne Cu. INTRODUCTION The Freeport McMoRan Miami smelter has been previously described in literature (Steinborn, Pasca, Sallee, Binegar, Bhappu). For the sake of brevity a brief description is given here. The Miami smelter is located 129 km east of Phoenix, Arizona near the town of Miami, Arizona. The smelter was established in 1915 and has undergone a number of process upgrades and modernizations over the years. The present smelter consists of an Isasmelt furnace, an electric settling furnace, four Hoboken converters, two anode refining vessels & one casting wheel; and one double contact sulfuric acid plant. Concentrates are railed & trucked to Miami from four Freeport McMoRan mines located in Arizona & New Mexico. The wet concentrates, typically containing 10% H2O with a Cu/S ratio of 0.85, are smelted in an Isasmelt furnace to a matte grade of 58%. The entire output from the Isasmelt is laundered into an Elkem electric furnace (originally installed in 1972 as the primary smelting furnace) for separation into matte and slag. Slag containing 0.85% Cu is skimmed from the electric furnace and discarded. Molten matte, containing 60% Cu, is tapped from the electric furnace and processed in one of four Hoboken converters to produce blister copper. Two anode refining vessels further refine the blister copper before the final product is cast on a single, 30 mold, casting wheel. All of the anodes produced at Miami are shipped to the Freeport McMoRan electrolytic refinery in El Paso Texas for refining into cathode copper. Smelter off-gases from the Isasmelt, electric furnace and Hoboken converters are combined and treated in a double contact acid plant to produce sulfuric acid. Acid produced at Miami is internally consumed at Freeport McMoRan mines in the region.

Jan 1, 2019

The area between Merrygoen and Digilah is located on a structural high that separates the Sydney Basin from the Great Artesian Basin, and hence the stratigraphic succession of younger rocks overlying the basement is relatively thin. The stratigraphy is briefly described and it is shown that fluvial sedimentation prevailed from Upper Permian through to Middle Jurassic times. Flint clays occur in the Permian, Triassic and Jurassic but only those in the Jurassic appear to have commercial value at present. The chemical, mineralogical, and physical properties of the flint clays are discussed.

Jan 1, 1973

By John F. Kearney

After World War II Canada?s fledgling iron ore mining industry developed along the ill-defined Quebec / Labrador border near what became the town of Knob Lake and later renamed Schefferville. For about twenty-five years from 1954 to 1982 Schefferville was the epicenter of Canadian iron ore mining and the foundation of the Iron Ore Company of Canada. In about 1982 it all stopped, shut down, the miners moved away leaving behind a mining camp and a ghost town that have sat idle and almost deserted for the past twenty five years. The story looks set to change with new plans to re-establish the former mining operations in the historic mining camp. This paper outlines the proposal to reactivate the direct shipping iron ore operations in the Schefferville mining camp, and specifically the properties in Labrador owned or optioned by Labrador Iron Mines Limited (?LIM?), a wholly owned subsidiary of London Stock Exchange listed Anglesey Mining plc. The Schefferville mining camp is located about 1,000 km northeast of Montreal. There are no roads connecting the area to southern Labrador or to Quebec. Access to the area is by rail from Sept Iles to Schefferville, or by air from Montreal and Sept Iles.

May 1, 2007

By R. G. Reddy

Nickel solubilities in spent pickling solutions (i.e. HF-HNO3-H2O solutions ) were measured as a function of HF and HNO3 acid concentrations. The chemical analysis of the industrial pickling solutions and sludges were made. The stable phases observed in the sludges are FeF3?3H2O, and ( FeCr ) F3?3H2O. Pure Ni, and stainless steel type 316 were used in this study. The results showed that the solubility of Ni increased with increase in concentrations of HF in pickling solution at a fixed concentration of HNO3: An excellent agreement between the experimental solubility data and the theoretical data was obtained. X-ray diffraction analysis showed that the solid solubility product formed is mainly NiF2?4H2O compound.

Jan 1, 1992

By P. G. Hallof

Only recently has the term Induced Polarization found its way into geophysical literature. Schlumberger first mentioned the possible use of the induced polarization effect in one of his early papers. Later, induced polarization was the subject of several university theses, such as Seigel's at the University of Toronto and Bliel's at the Michigan School of Technology. In addition, a group at the New Mexico School of Mining and Technobgy has done work on induced polarization. There is very little to be found in print on the subject of induced polarization. Several papers have been presented at meetings, the 1958 AIME and SEG* conventions, for instance, on laboratory measurements of the effect and theoretical considerations useful in the interpretation of field results. This paper is the first attempt to present actual field results which show the usefulness of induced polarization as a prospecting technique. There are several phenomena that can cause polarization when electrical current is passed through the ground. In a paper presented at the 1958 SEG* meetings Professor T. R. Madden of M. I. T. demonstrated that only two of these gave rise to appreciable effects. The first is a result of the membrane and diffusion effects in a sandstone that contains appre- ciable amounts of clay minerals. The unbonded charges associated with the clay mineral forma material that passes positive and negative ions with different mobilities. When current is passed through such a system for some period of time, polarization results. The second phenomenon, which gives rise to very much larger polarization effects, is the one used in the new prospecting technique. These effects are a result of the blocking action or polarization of metallic or electronic conductors in a medium of ionic solution conduction. This electrochemical polarization, called "the over-voltage effect" by electro-chemists, occurs whenever electrical current is passed through a volume of rock which contains metallic minerals such as base metal sulphides. This polarization at metallic interfaces in ionic solutions depends upon the chemical energies necessary to allow the ions to continue the flow of current by giving up or receiving an electron from the metallic surfaces. The energy stored in this reaction isanalogous to that stored when a condenser is charged. If a d. c. current flowing through such a system is interrupted, the polarization can be detected as a small, decaying current that flows after the applied current is discontinued. The decaying potential measured is a result of the current flow caused by charges returning to their equilibrium positions from the positions they assumed under the applied potential field. Because of the polarization, there is an excess of change at each metallic interface. There is an alternate method of measurement of the induced polarization effect. The electrical

Jan 1, 1961

By John C. McDonald

This report is a continuation of an earlier one with a similar titlell to which the reader is referred for such details of procedure as do not appear here. A brief summary will be given of the objects and methods of the research at this time. It was pointed out in the previous paper that properties of magnesium alloys, as reported by different workers, often differ. This was thought to be due to differences in the preparation of the specimens tested. The ideal way to compare alloys would be to prepare each of them in so many ways that reasonable assurance would exist that the best properties of each alloy had been developed. The alloys would then be compared on the basis of these properties. The treatment actually given the alloys of these studies is necessarily a compromise with completeness. Nevertheless, enough treatments have been given so that a considerable degree of assurance exists that the properties obtained are representative of the alloy as such, and not merely of the manner in which it was worked and heat-treated. Procedure The alloys were cast in the form of cylindrical ingots, which were extruded into bar before being rolled. Some of the ingots were made in 2-in. diameter molds whereas all of the alloys of the previous paper were cast in 4.in. molds. For the larger ingots, the extruded bar was 2 by 0.140 in.; lor the 2-in. ingots, it was I by 0.100 in. Preliminary work indicated that strip rolled from both sizes of the bars would have substantially the same properties. The bar was rolled at some temperature in the range 400' to 800°F., for a total reduction of 50 per cent. The temperature and reduction per pass were so selected that no cold cracking occurred, but were such as to leave the metal in a semihard condition. The hot-rolled metal was annealed at several temperatures in the range 400' to 800°F.; it was also cold-rolled, and given solution and aging treatments. Two standard test bars corresponding to each treatment were pulled in tension, and the average was obtained. Twelve treatments, in all, were given each alloy. The properties of the annealed specimen having the highest percentage of elongation were selected to represent the alloy in the annealed condition. The properties of the cold-rolled specimen having the highest yield strength were selected to represent the alloy in the cold-rolled condition. These properties were then plotted against percentage composition by analysis. Smooth curves were drawn among the points, thus graphically averaging the results over the entire range studied. The percentage of elongation in the cold-rolled state was not plotted, since it was always low, and varied in an irregular manner with composition. Alloys Studied Magnesium-calcium Alloys.—Fig. I presents the results on the alloys of the rnag-

Jan 1, 1941

By John C. McDonald

This report is a continuation of an earlier one with a similar titlell to which the reader is referred for such details of procedure as do not appear here. A brief summary will be given of the objects and methods of the research at this time. It was pointed out in the previous paper that properties of magnesium alloys, as reported by different workers, often differ. This was thought to be due to differences in the preparation of the specimens tested. The ideal way to compare alloys would be to prepare each of them in so many ways that reasonable assurance would exist that the best properties of each alloy had been developed. The alloys would then be compared on the basis of these properties. The treatment actually given the alloys of these studies is necessarily a compromise with completeness. Nevertheless, enough treatments have been given so that a considerable degree of assurance exists that the properties obtained are representative of the alloy as such, and not merely of the manner in which it was worked and heat-treated. Procedure The alloys were cast in the form of cylindrical ingots, which were extruded into bar before being rolled. Some of the ingots were made in 2-in. diameter molds whereas all of the alloys of the previous paper were cast in 4.in. molds. For the larger ingots, the extruded bar was 2 by 0.140 in.; lor the 2-in. ingots, it was I by 0.100 in. Preliminary work indicated that strip rolled from both sizes of the bars would have substantially the same properties. The bar was rolled at some temperature in the range 400' to 800°F., for a total reduction of 50 per cent. The temperature and reduction per pass were so selected that no cold cracking occurred, but were such as to leave the metal in a semihard condition. The hot-rolled metal was annealed at several temperatures in the range 400' to 800°F.; it was also cold-rolled, and given solution and aging treatments. Two standard test bars corresponding to each treatment were pulled in tension, and the average was obtained. Twelve treatments, in all, were given each alloy. The properties of the annealed specimen having the highest percentage of elongation were selected to represent the alloy in the annealed condition. The properties of the cold-rolled specimen having the highest yield strength were selected to represent the alloy in the cold-rolled condition. These properties were then plotted against percentage composition by analysis. Smooth curves were drawn among the points, thus graphically averaging the results over the entire range studied. The percentage of elongation in the cold-rolled state was not plotted, since it was always low, and varied in an irregular manner with composition. Alloys Studied Magnesium-calcium Alloys.—Fig. I presents the results on the alloys of the rnag-

Jan 1, 1941

By P. W. Barton, A. A. Johnson, E. J. Hughes

THE only systematic work on the effect of carbon on the recovery and recrystallization kinetics of iron so far reported in the literature is that of Venturello et al.1 These workers found that doping high-purity iron so that it contained up to 86 ppm C caused a marked retardation of recovery but had little or no effect on the recrystallization kinetics. Such evidence for an effect as was obtained was inconclusive. In the course of a study of electron-beam zone-refined iron the authors have recently examined the effect of added carbon on the recrystallization kinetics of this material. The amount of carbon added was about 50 pct more than was used by Venturello et 01. and definite evidence was obtained that carbon at this level retards recrystallization. The starting material was taken from a batch of 0.2-in.-diameter Johnson-Matthey spectroscopically pure iron rods which had been further purified by being given three passes at 4 in. hr-1 in a standard MRC electron-beam zone-refining unit. The purity of this material. which was used in two other investigations of the properties of high-purity iron,2,3 was established by an extensive series of analyses. Four laboratories, the National Research Corp., Newton, Mass., the Naval Research Laboratory, Washington, D.C.. the Battelle Memorial Institute, Columbus, Ohio, and the National Physical Laboratory. Teddington. Middlesex, England. carried out analyses for carbon. oxygen. and nitrogen. and in addition a complete mass-spectrograph analysis was carried out at Battelle. In all, twelve analyses were carried out for carbon, seventeen for oxygen and twelve for nitrogen. The amounts of these elements found to be present were 10 * 7, 8 i 5, and 0.9 i 0.1 ppm, respectively. The limits given are rms deviations. Two results, one of 46 ppm of oxygen and another of 31 ppm of nitrogen, were rejected as anomalous. The mass-spectrograph analysis revealed the major impurity to be 25 ppm of tungsten. All of the other elements detected were present in amounts less than 0.5 ppm. Some of the rods were doped with carbon by being immersed in a suspension of carbon in oil, heated in a vacuum at 400°C, and then zone-leveled to make the distribution of carbon uniform. Carbon analyses carried out on three of the doped rods gave a mean value of 130 ± 45 ppm. Some of the doped and undoped rods were deformed 58 pct by swaging and cut into specimens 1/2 in. in length. Isothermal recrystallization experiments were then carried out on them at 575", 600°, 615", 630°, and 650°C, the volume fraction of each specimen recrystallized being measured by a point-counting method described by Hilliard and Cahn.4 The results for the two types of specimens are shown separately in Figs. 1 and 2. In Fig. 3 the pairs of recrystallization curves for each temper-

Jan 1, 1965

• In 1949 the United States imported 7,400,000 tons of iron ore; Chile, Sweden and Canada, in that order of importance, supplied over 80 pct of this amount. U. S. imports have increased from 3 pct of the total supply in 1940 to 8 pct in 1949. • Mica has been successfully synthesized by scientists of the National Bureau of Standards. quartz, magnesite and bauxite, plus a fluorosilicate compound to act as a crystallizing agent, are heated to 2500°F in a platinum-lined crucible and as the furnace cools mica crystals grow. The key to parallel growth to make sheets is in precision control of temperature. • Inland Steel Co. of Chicago has taken an option to lease from Steep Rock Iron Mines, Ltd., of Canada -- a large undeveloped acreage in the vicinity of Steed Rock Lake, Ontario -- for the purpose of exploring and developing a new iron ore mine. The exploration program is expected to begin at an early date. •A 20-yr test conducted by the U. S. Bureau of Mines with the cooperation of Cleveland-Cliffs indicated that chemically treated timbers last from 2 to 3-1/2 times as long as untreated ones set in the same passageway. Of the three reagents used, zinc chloride gave the best result -- 13.3 yr as compared to 3.8 yr for untreated timber. •Senator Pat McCarran charged that President Truman used a "shotgun approach" to the taxation problem when he accused the mining industry of enjoying excessive depletion exemptions when actually mining taxes should be lowered. He introduced to the Senate a report of the National Advisory Council -recommending a decrease * The country's first graduate program of research and instruction in conservation of natural resources will begin at Yale in September. The Conservation Foundation is supplying $20,000 a year to finance the program. •Felix E. Wormser urged that adequate tariff protection should be provided to offset effects of devaluation on the domestic mining industry in an address before the Colorado Mining Association. He advocates tariffs rather than subsidy legislation, such as S. 2105, for the protection of the lead-zinc miners because the latter would promote inefficiency and "impair our priceless free market." •"It may be startling to realize that for the world's white population the per capita requirements for minerals have multiplied 30 times in 30 yr, or that more minerals have been mined in the last 40 yr than in all prior history." -- Evan Just, in "Mineral Depletion and Metal Supply." •The National City Bank in its monthly letter states that both management and the unions concede that there are too many miners trying to make a living out of the industry for its present market. •On Feb. 3 it was reported that 6000 Anaconda employes in Chile quit jobs in sympathy with striking telephone and electric workers. The government has ordered them back to work on penalty of discharge. It appears that the walkout will not be prolonged in view of the government stand.

Jan 3, 1950

By J. W. Borough

THE electrical conductivity of pure copper is markedly decreased by small amounts of impurity in solution. The magnitude of this effect has been very carefully determined by numerous investigators who studied a wide variety of impurity elements. Much of this work is summarized in an excellent review by Pawlek and Reichel.' The case of zinc impurity in copper is an exception to the above in that there has been no well-documented study of the effect using high-purity starting materials. The values for the effect of zinc on conductivity, which are usually taken from unpublished work by Skowronki, indicate that zinc in low concentration has no effect whatever in lowering the conductivity of pure copper. This effect, if true, is unusual since it is generally known that even in lowest concentration, impurities exert an effect on conductivity which is proportional to the amount dissolved. It is more reasonable to suspect that in the original work on the effect of zinc some of the zinc was oxidized out of solution during specimen preparation. The following experi- and calculated d-spacings based on the unit cell dimensions of Baenziger et al. Since the single crystal studies of Baenziger et al. were limited to (hk0) and (hk 1) data, it was not possible to Compare all the intensities of the powder and single crystal patterns. However, the strongest reflections of both studies, the (321) reflection, agree very well when the appropriate multiplicity factor is used. Good agreement was also found in a number of other reflections of lesser intensity. Despite the precautions taken in annealing the U6Fe powder, an appreciable amount of UO, was detected in the powder pattern after heat treatment. The powder pattern reported by Groganoand Clews is given in Table I. Except for the 3.15A line, which is the strongest line of UO,, their pattern, as far as it goes, compares favoEably with the data from this study. Gordon and Kaufmann have reported a diffraction powder pattern purported to be U, Fe but it bears very little resemblance to the patterns of Table I. ments were carried out to redetermine the effect of zinc on conductivity using high-purity starting materials and processing conditions capable of producing oxygen-free alloys. Materials used in the experiment were ASR 99.999 pct Cu and Cumingo 99.999 pct Zn. Four 1 lb melts were prepared with identical procedure in argon atmosphere with crucibles made from Speer No. 580 graphite. The compositions were 0.0, 0.1, 0.3 and 1.0 pct Zn. Standard No. 14 wire (0.064 in. diam) was made from these melts as follows. The 1 pct Zn sample was first reduced 94 pct by cold swaging with five annealing treatments of 800o for 10 min in hydrogen between swagings, and then reduced 94 pct to the

Jan 1, 1962