Search Documents

The Rate Variable Batch Test (RVBT) - A Research Method of Characterising Ore Floatability

Sep 13, 2010

By K. D’Elia, L. D. Ogrel, O. A. Malyshev, T. I. Yushina, I. M. Petrov

"The purpose of this research is to develop enhancements in the mineral processing by flotation methods of nonferrous ores. Currently, 180-190 million tons of ore are processed by flotation in Russia. The annual processing volume of copper-nickel and copper-zinc ores exceeds 20 million tons. In the total volume of processed ores by flotation, non-ferrous ores account for roughly 35% and ores of precious metals for another 15%. The total demand of flotation reagents in Russia in 2016 was estimated at 170,000 tons. Sulfur-based collectors used in the flotation of non-ferrous sulfide ores (typically, xanthates) do not always offer sufficiently high recovery of valuable components.It has been found that reagents like DMIPEC and DK-80 improve the recovery of metals into concentrates. To identify the reasons of that higher recovery, quantum chemical calculations of the mechanism and interaction forces of DMIPEC with non-ferrous sulfides were undertaken by determining the stabilization energy of the resulting chemical complexes. It has been shown that, in the interaction of DMIPEC and DK-80 with the surfaces of sulfide minerals, ethylene and acetylene bonds act as the reaction centers, and the formation of molecular p-complexes is the result of metal-cation interactions with the surface and the flotation reagents.In the flotation of non-ferrous ores, DMIPEC and DK-80 act as selective supplementary collectors with foaming properties, and at a flow rate of 3-35 g/ton, they reduce the flotation time, and increase copper recovery by up to 3.5%, zinc recovery by up to 12%, gold recovery by up to 8-10%, allowing to increase the recovery of valuable components by 1.5-12.0%, basically this kind of reagents nearly double the flotation rate, improve the grade of the concentrate, improve the stability of the flotation process parameters, and reduce the environmental impact of flotation plants."

Jan 1, 2018

By P. Zhang

Previous studies have shown that separation of clay minerals from non-clay minerals is the key to economic recovery of the phosphate from the waste phosphatic clays (slime) which represent about 20- 300/0 of the phosphate mined. Small hydrocyclones of different sizes (4" and 6") were tested for sizing the slime at +10 microns in order to remove most of the clay minerals. The effect of design variables and operating parameters were evaluated. Multi-stage cycloning and the effect of dispersant were also investigated. Chemical and mineralogical analyses of different size fractions of both the underflow and overflow samples indicated satisfactorily separation efficiency.

Jan 1, 1998

By H. Wotruba, K. Neubert

Dual-energy X-ray transmission (DE-XRT) imaging is known from safety luggage inspections at airports. The use of DE-XRT technology for sorting applications in the primary raw materials industry has been the subject of numerous investigations. Beside other metal ores, X-ray transmission sorting is already used for the preconcentration of tungsten ore, gold ore and coal. The applicability of DE-XRT sorting is limited to ore types where differences in metal concentrations are measurable, based on an interpretation of X-ray images. Metal contents in particles occur in large varieties in terms of concentration, grain sizes, spatial distribution and mineralogy and therefore influence the X-ray absorption. As a result, each ore has to be tested individually for its suitability for DE-XRT sorting. The objective of current research at the Department of Mineral Processing (AMR) at RWTH Aachen University is to assess parameters influencing the detectability of rare earth oxides. Two approaches were followed: (1) Practical test work, based on artificial ore samples of defined compositions and (2) Computer-based simulation of absorption features of identical particle compositions. In total, more than 300 artificial samples of various compositions and metal grades were produced and X-ray images from DE-XRT sorting were analyzed. Results from the DE-XRT sensor were put into correlation with metal grades and particle sizes, to analyze influences and limits on the detectability of rare earth oxides. In addition, a new approach was tested in which the X-ray absorption of particles of various compositions was determined based on a Monte Carlo (MCNP) simulation. During the simulation, similar compositions, as used for the artificial samples, were tested and the X-ray absorption behavior during DE-XRT sorting was determined. A comparison of results from both approaches is used to assess the applicability of the MCNP-simulation for the prediction of the X-ray attenuation behavior during DE-XRT sorting.

Jan 1, 2016

By P. K. Frempong, S. D. Butt

"A case study for the application of a novel geostatistical technique for resource estimation of a narrow steeply dipping, gold-silver mineralized quartz vein deposit is presented. The technique is novel in two respects. First, mineral grades are kriged directly rather via the accumulation method more often applied to vein deposits and, second, a modified 2D ordinary kriging algorithm is used that allows the calculation of a single grade and variance for irregular shaped blocks of varying sizes. The objective of this investigation was to evaluate the suitability of this novel geostatistical technique for resource estimation of the Poura mine deposit and, if appropriate, to lay a firm foundation for future geostatistical work at the mine.The reserve estimation concentrated on the remnant ore blocks and pillars in both underground and surface workings. The data, which was collected in 2D coordinates with grade and vein thickness values, was first analyzed statistically and used to compute experimental semi-variograms. Appropriate semivariogram models were fitted and various aspects of the estimation technique were evaluated using cross-validation error analysis, with acceptable results. A block kriging computer program called Krige2D was developed to implement the modified 2D kriging algorithm and calculations. Production data were not available to evaluate the computed block resources, but they were compared with a previous resource data determined using an arithmetic approach. The geostatistical technique estimated slightly higher grades but lower overall tonnages as compared to the earlier arithmetic estimates."

Jan 1, 2004

A case study for the application of a novel geostatistical technique for resource estimation of a narrow steeply dipping, gold-silver mineralized quartz vein deposit is presented. The technique is novel in two respects. First, mineral grades are kriged directly rather via the accumulation method more often applied to vein deposits and, second, a modified 2D ordinary kriging algorithm is used that allows the calculation of a single grade and variance for irregular shaped blocks of varying sizes. The objective of this investigation was to evaluate the suitability of this novel geostatistical technique for resource estimation of the Poura mine deposit and, if appropriate, to lay a firm foundation for future geostatistical work at the mine. The reserve estimation concentrated on the remnant ore blocks and pillars in both underground and surface workings. The data, which was collected in 2D coordinates with grade and vein thickness values, was first analyzed statistically and used to compute experimental semi-variograms. Appropriate semi- variogram models were fitted and various aspects of the estimation technique were evaluated using cross-validation error analysis, with acceptable results. A block kriging computer program called Krige2D was developed to implement the modified 2D kriging algorithm and calculations. Production data were not available to evaluate the computed block resources, but they were compared with a previous resource data determined using an arithmetic approach. The geostatistical technique estimated slightly higher grades but lower overall tonnages as compared to the earlier arithmetic estimates.

Feb 1, 2004

By Takahiro Kubo, Katsunori Yamaguchi, Hidehiro Sekimoto

Equilibrium relation between B2O3 slag, RExOy-B2O3 (RE = rare earths) slag and Fe-C alloy formed by melting treatment of neodymium magnet and B2O3 was investigated. When neodymium magnet was melted together with B2O3 and Fe-C alloy in carbon crucible, 3 liquid phases of B2O3 slag, RExOy-B2O3 slag and molten Fe-C alloy formed and clearly separated by the difference of the specific gravities. In the case that excess amount of Cu was also introduced in that system, molten Cu phase additionally formed. Almost all amount of RE were concentrated in RExOy-B2O3 slag. The concentration of RE in RExOy-B2O3 slag increased with the decrease of the melting temperature. While chromium, phosphorous, nickel, cobalt, and copper were concentrated in molten Fe-C alloy, silicon and aluminum were distributed in B2O3 slag and RE2O3-B2O3 slag.

Jan 1, 2014

The deposit was discovered during systematic reconstruction of the geological history of glacial overburden, which averages 6 m in thickness over 80% of Sweden, by geochemical sampling and searching for small grains of eroded bedrock. The gold is mainly concentrated in and around high-grade quartz veins within a broad shear zone, though the correlation coefficient between quartz and gold in samples is not significant. Production from two pits, now connected, in the Central and Eastern orebodies has increased steadily from 1 238 kg Au in 1989 to 2 120 kg in 1994, the highest in Europe. The mine has adapted and improved its mining methods to achieve significant productivity increases and cost reductions. Most of the improvements have been achieved through a better understanding of the controls on mineralisation and of the implications of those controls for selective mining. Geostatistics has played an important role in the quantification of grade variability and gold occurrence. Better blasting and loading techniques have improved selectivity, grade control has been enhanced by a grade-control drilling programme, and significant improvements in mineral processing have been made

Dec 1, 1995

By Brian Heer, David Young, Randall Essex

The Manapouri Power Station is New Zealand’s largest hydroelectric facility located on the South Island of New Zealand. Constructed in the 1960’s, it includes a 700 MW under-ground power station and a 9.8 km (6.1 mile), 9.2 m (30 ft) diameter tailrace tunnel. The output of the power station is currently limited due to excessive head losses in the tailrace tunnel. To remedy this situation, the Electricity Corporation of New Zealand (ECNZ) retained Woodward-Clyde to design a second tailrace tunnel and appurtenant facilities and prepare Contract Documents for construction. The Project will involve the construction of a 9.8 km(6.1 miles), 10 m (33 ft) diameter, TBM-mined tunnel, hydraulic control structures at the upstream and downstream ends of the tunnel, an underground dewatering shaft and station, and tailrace channel improvements. This paper summarizes the key design and construction issues addressed during the planning and design phases, outlines the risk management provisions incorporated in the Contract, and overviews the Interactive Tender Process (ITP)that was implemented during the pre-tendering and tendering periods.

Jan 1, 1997

By O. Schumacher

Guidelines for publication of information defining the amount and grade of resource material available in a deposit are well established in Australasia?s JORC Guidelines, Canada?s National Instrument 43-101 and similar documents in South Africa, Peru, Chile and elsewhere (Table 1). These guidelines provide standards to apply regarding the geologic and geostatistical basis for describing the level of confidence to be assumed for an estimate of the amount and grade of material. All of them provide for a strict distinction between material that has been demonstrated to be economically mineable and that which has not, and all of them provide terms such as ?resource? or ?exploration information? to be applied to data regarding material that has not been demonstrated to be economically mineable. It is not until an economic study has been completed that we are allowed to apply the powerful terms ?reserves? and ?ore? to our deposit material. Indeed, the application of these eye-catching labels immediately tells the reader that an economic study has been completed by a qualified person, and that the results of the study were positive. While extensive guidelines are established for describing the level of confidence in published geologic data, and the nature of the economic study that should be accomplished before using the terms ?reserves? or ?ore?, surprisingly little guidance is provided regarding the process to use, and the level of detail to attain, for estimating capital and operating costs for the study. The intent of this paper is to lay the groundwork for development of suitable guidelines for the cost estimating process. While the codes do not provide specific instructions for the cost estimate, they do provide numerous hints and clues to help determine the level of detail expected and the type of procedure to apply in preparing the estimate. This paper will first review the various codes to gain an insight into the thinking of the drafters of the codes regarding their unstated expectations for the cost estimating process. Based on this review, a series of guidelines are proposed for this purpose.

Feb 27, 2013

"A coordinated, integrated research effort aimed at studying the scientific, engineering and medical aspects of the respirable dust problem is underway in the areas of dust generation, dust dispersion and dilution, dust characterization, interaction of dust and lungs, and relationship of seam characteristics to dust generation and mobility. (FIGURE 24) The Center's research program explores these concerns with the objective of refining existing strategies and developing new respirable dust control techniques that are consistent with the dust-lung interaction processes that lead to mine worker disability. The fundamental aspects of this work are applicable to the control of respirable dust problems in both hard rock mines and coal mines and to other dusts such as diesel-generated.Research projects in the Generic Mineral Technology Center for Respirable Dust have effected several improved methods for the preparation and characterization of the dusts needed by these projects. Superior procedures for generating ""standard"" dust samples have been developed and are in regular use in the laboratory. Questions raised during the course of some projects regarding ""stale"" versus ""fresh"" dust have led to the development of sampling techniques where the dust is directly collected in a surfactant. MSHA and CANMET have requested and received information on Center generated software. An equipment manufacturer, TSI, Inc., requesting input on modifying the inlet of an aerosol sampler has been assisted as a result of research that was conducted at the University of Minnesota.The objectives, scope and progress of all the research projects in the Center, in the form of abstracts and reports, have been detailed in Volume 1 of this series. Research papers written by the principle investigators and resulting from the findings of projects (FIGURE 25) and which are funded by U.S. Bureau of Mines grant number G1135142 have been published in Volumes 3 through 6 and Volume 8 of this series. Volume 2 relates the cooperation and interaction of the U.S. Bureau of Mines and the Generic Mineral Technology Center for Respirable Dust in research on the problem of respirable dust in the mineral industries."

Aug 31, 1989

By David M. Davidson

Seven intrusive phases have been mapped to date in the 1 b.y. Red Bluff Granite Complex (RBGC) near El Paso, Texas. This batholith is 20 km2 in area and intrudes older supracrustal units as well as a trachyte ignimbrite cap. Two early microgranite sills are spatially separated 6 km from a porphyritic, three-phase "ring complex" by a tin-bearing, biotite granite which cores the RBGC. These units are intruded, in turn, by a riebeckite granite which locally exhibits lineated and pegmatitic textures as well as exceptionally high light REE and Zr values (800 ppm La; 3,000 ppm Zr). The riebeckite granite is exposed in three separate occurrences within the Franklin Mountains. REE values in the RBGC are depleted in HREE and show distinct negative Eu anomalies. Typical La/Yb ratios are 5:1-2:1 with Eu values ranging from 10-80 ppm. The mineral source of the high REE values in the riebeckite granite has not yet been specifically identified, but is believed to be zircon.

Jan 1, 1988

By Mark Koelling

This paper presents a case history of a ground improvement program conducted in a soft soil environment and seismically active region in the northwest corner of Washington State near the Canadian border. The program was performed over several years, and provided adequate soil bearing conditions for the construction of several structures. Completed development includes separate construction of four adjacent structures, each with unique total and differential settlement requirements and built at approximate two year intervals. Site soils consist of 45 feet of loose saturated sand and silt overlying 70 feet of very soft to stiff (N60 = 0 to 7) normally consolidated clay. Adding to the complexity of the site is the owner?s requirement that all existing structures remain open and in service during construction of each subsequent structure. The paper presents the site geotechnical information and the foundation design issues. Details of a combination of ground improvement methods is presented, including stone columns, wick drains, a preload surcharge, and staged construction to provide soil support for shallow foundation construction of all structures at this site. The soil test results and settlement observations are presented along with QA/QC measures. Lastly, a brief method sustainability comment will be made.

Jan 1, 2010

By F. J. Sotillo

Mineral processing requires good classification of particles to attain an adequate separation of minerals. This is of utmost importance in the case of sulfide minerals. An ideal classification is obtained when particles are separated at a given mesh, which is fixed according to the characteristics of each sulfide ore. Under these ideal conditions, particles coarser than the mesh of separation are recovered in the underflow, whereas particles finer than the mesh of separation are recovered in the overflow. This paper presents the results of pilot plant tests that were performed on Ag-Pb-Zn and on Ag-Au Peruvian sulfide ores using a Density Separator, and the comparison of these results with those obtained using hydrocyclones, under similar operating conditions. The results show that the ratio of circulating load is reduced by 50% by using a Density Separator with respect to that obtained by using hydrocyclones. Moreover, the effect of the improvement in the separation efficiency obtained by using the Density Separator on the kinetics of flotation is also shown. Silver recovery of the Ag-Pb-Zn ore increased by 18% whereas gold grade in the concentrate of the Ag-Au ore is doubled.

Jan 1, 1998

By Morris Cohen, Robert C. Ruhl

The phases in Fe-C alloys over a wide composition range have been studied after splal quenching from the liquid state. Binary alloys containing 0 to 5.1 wt pel C as /cell as a large number of ternary Fe-C-Si alloys with 2.5 to 5.0 wt pct C and 0.3 to 5.1 wt pct Si were attlong those sludied. Olher Fe-C-X alloys, zcilh X being Co, Cr, ,Wn, Ni, and Ru , were also inrestigated after splat quenching. At high carbon contents, a new hcp phase (designaled 6 phase, but different from e carbide) is retained upon splat quenching. The .fraction of this phase varies up lo 97 pcl for a Fe-4.K-1.9% alloy. The composition of the E phase ranges from about 3.8 10 4.8 wt pet C, and the corresponding laltice parameters increase linearly ulith carbon content, while the c/a ratio remains essentially conslc~nl. The E phrtse appears to he a solulion of carbon in E iron, the latler being nornially found only at high pressures. It is deduced that the unit cell of the E phase corresponds to the formula Fe12C3, and llzal il is relaled to tlie ordered slruclures 0.f 6 iron carbide and c iron nilride. The E phase is compared and contrasted to the olher known carbides and nitrides of iron and nickel. An exlrapolaTion of the atomic volume 1,s carhon conlent of /he E pllase lzcts giz.en a neu7 estitnale jor /he alomic volume of E iron, 11.30 cu A, a1 atmospheric pressure and temperature. Other alomic volume relalionships lead to /he co~zpositioti Fe2.iC tor E iron carbide, /he unit cell fortr~ula being -Fe2rClo The E phase undergoes a lulo-slage decomposition upon healing, .forrning firsl rnarlensile plus E carhide, a/ler 1 hr at 140" lo 200°C, slid then ferr ite Plus cementile, after 1 lir a1 330" to 460°C. A1 carbo,l contents between 1.5 and 3.0 LC/ pcl, (he predo.wirzar/t plzase alley quenching is fcc austenite. The retained carbon content of this phase increases with itlcreasing silicon in certain concentration ranges, reaching a maximum of 2.37 wt pct C itz a Fe-2.6C-4.OSi alloy. This is the highest carbon conten1 reLaitled in austenite to date. These high-carbon aus-tenites can be partially tm?zsforttled lo tnartensile hy severe deformation in the temperature range of — 190 to -50°C. TECHNIQUES for splat quenching from the liquid state have been utilized in numerous recent investigations to produce metastable phases in a variety of alloy systems. Among the several ways of splat quenching, the shock-tube method appears to yield the highest cooling rates1-3, 7, 8 and was adopted here. Estimated cooling rates attained in the present experiments ranged from 10' to 10 80Cper sec.' As a part of a research program on interstitial al- loy phases, the Fe-C system was selected for splat-quenching studies. It was hoped that splat quenching would allow high metastable supersaturations of carbon to be retained in solution. Also of considerable interest were the conditions governing the occurrence of the various intermediate phases upon solidification. The alloys investigated included both binary Fe-C compositions as well as six ternary Fe-C-X alloy systems. The known phases in the Fe-C system are summarized in Table I.* Only the ferrite and graphite are ent investigation.14 and is described in detail herein Table II summarizes corresponding data on Fe-N phases, which are also of interest here because of their similarity to the Fe-C phases. EXPERIMENTAL PROCEDURES Alloys were prepared by melting the elements. 99.9 pct purity, in an inert gas nonconsumable electrode arc furnace. The buttons. weighing about 5 g. were remelted twice. were then fragmented. and their interior surfaces were examined for uniformity: if any doubt existed. they were remelted again. Chemical analyses were performed on all the alloys. the accuracy being about k0.05 wt pct. At high temperatures, carbon-containing alloys react with alumina crucibles as follows: If the atmosphere in the splat-quenching furnace does not contain sufficient carbon monoxide the alloy can be depleted of carbon and contaminated with aluminum. Calculations and experimental observations showed that 50 to 100 torr CO partial pressure effectively blocked the above reaction in all the alloys investigated. The splat-quenching equipment in Figs. 1 and 2 provides for evacuation and back-filling with CO-Ar mixtures. The furnace is capable of operation up to 1650°C. and the gettering action of the graphite heating element reduces the oxygen partial pressure in the furnace atmosphere to below 10-5 torr, thus preventing oxidation of the specimens.

Jan 1, 1970

By J. D. Embury, R. M. Fisher, A. S. Keh

An investigation of the defect structure and properties following large strain deformation has been carried out using transmission electron microscopy and mechanical testing for a range of ferrous materials and for copper. It is shown that, for a variety of ferrous materials, a cellular substructure is developed during the initial stages of working and on further deformation the dimensions of this substructure are reduced. Quantitative measurements of the flow stress and the scale of the substructure indicate that the strength of heavily worked materials is largely determined by the spacing of cell walls. These cell walls act as dislocation barriers in a manner analogous to grain boundaries. FCC materials do not harden as extensively as bcc after cold working and the present observations on copper indicate that the dimensions of the substructure in fcc materials are not markedly reduced on deformation. The differences between the fcc and bcc structures produced by large plastic strains are ascribed to differences in the extent of dynamic recovery. It is tentatively proposed that the greater stability of substructural barriers in bcc structures results from strong interstitial Pinning effects. It is proposed that for large plastic strains the work-hardening process may be considered in terms of the reduction of substructural-barrier spacing during the working process. This pvovides a simplified hut useful analysis of the strain hardening occurring during mechanical processes. THE mechanisms of strain-hardening processes have occupied the attention of numerous investigators over the past three decades and a multitude of theories have emerged in this field. The majority of previous work has been concerned with the development of a description of the plastic behavior of single crystals in terms of dislocation theory.'" In contrast, scant attention has been given to the strengthening mechanisms operative during mechanical working processes such as rolling and drawing. The large plastic strains involved in these processes make it difficult to correlate the observations with any elementary dislocation theory. Further, as Bullen and coworkers3 have opined, for large plastic strains both hardening and recovery occur simultaneously and thus it is extremely difficult to estimate the effect of plastic strain on the ambient internal stress field. It is probable that for large plas- tic strains any theoretical estimate of the internal stress field must be made in terms of complex dislocation groups. Although some valuable theoretical work has been done toward calculating the elastic properties of dislocation groups4 any detailed self-consistent model for large plastic strain is as yet impossible. With these limitations in view it is still of value to examine the mechanical properties of highly strained materials as a function of their substructure. This relationship is explored in the present communication for a variety of materials subjected to rolling, drawing, or swaging. The primary object of this investigation has been to establish the validity and the limitations of the substructural strengthening mechanism proposed by Embury and eisher' for drawn pearlitic wire and by Meieran and Thomas for drawn tungsten wire. No attempt has been made to delineate the basic interaction mechanism which occurs between a slip dislocation and the substructure and the authors believe that a great deal more experimental evidence must be compiled before these fundamental aspects can be explored. Also, no specific attention has been given to the detailed formation of substructure during working. Experimental Details. A variety of materials were used in this investigation, the compositions and heat treatment of which are tabulated in Table I. The commercially pure iron is referred to throughout this report as Ferrovac E. The mechanical working processes were all performed at room temperature. The wire drawing was performed on a manual drawing bench. Reductions of between 10 and 20 pct in area per pass were used in both swaging and drawing. The experimental parameter used to evaluate the mechanical properties of the materials was the 0.2 pct proof stress. This was determined for wire samples using an Instron tensile machine at a crosshead speed of 0.02 in. per min. The techniques for preparation of samples for transmission electron microscopy have been described previo~sl~.~ Specimens from wire samples were prepared from longitudinal sections and in some cases from transverse sections. To evaluate the substructural characteristics of rolled materials, thin foil samples were prepared of both the face and edge sections. Results. One of the more familiar ways of expressing work hardening in mechanical working is by the flow stress as a function of reduction in cross-sectional area. Fig. 1 shows such a plot for Ferrovac E eutectoid carbon steel and for copper. The curve for Ferrovac E is characterized by an initial stage of rapid work hardening and a final stage of rapid work hardening separated by an intermediate stage with a low rate of work hardening. This behavior is typical of many ferrous materials and the drawn pearlite wire previously investigated by Embury and Fisher is a more pronounced example. Copper shows an initial

Jan 1, 1967

By C. A. Stickels

A heat of electrolytic iron, to whzch alunzinutn and nitrogen had been added, was hot-rolled, cold-rolled 90 pct, and recrystallized at temperatures from 500" to 700°C. Primary recrystallization textures appear to arise from competitive growth of two types of nuclei: 1) those having orientations belonging to the "usual" primary recrystallization texture found in riming steel, and 2) those with the {111} (110) ovientation. Development of a (111}(1 10) component in the primary recrystallization texture occurs only over a certain interval of isothermal recrystallizatzon temperatures when the material is supersaturated with respect to the precipitation of AlN. Lowering the degree of supersaturation depresses the temperature interval in which a (111)(110) component occurs. An elongated, 'pancake-shaped" recrystallized pain structure and a marked delay in the start of recrystallization were found in all specimens which were supersaturated with respect to A1N precipitation after cold work, regardless of their recrystallization texture. ONE of the consequences of killing low-carbon steel with aluminum is a significant change in recrystallization behavior. About 15 years ago, Solter and eatttiel showed that this behavior was largely controlled by aluminum and nitrogen in the steel. If complete precipitation of A1N was prevented before cold rolling, an increased "recrystallization temperature" was observed in subsequent. annealing, and the recrystal-lized grains were not equiaxed. Leslie et a1.2 studied this phenomenon in some detail and clearly demonstrated the relationship between A1N precipitation, recrystallization kinetics, and the development of "pancake-shaped" grains. It has also been known for some time that aluminum-killed steels, processed to produce elongated "pancake" grains, develop a (11 I}( 110) primary recrystallization texture. This texture has not been found in iron or low-carbon rimming steel as a primary texture4j5 but has been observed following grain growth in electrolytic iron.5 The present work was undertaken to study in more detail the effect of A1N supersaturation on recrystallization textures in iron. LITERATURE REVIEW The deformation texture in heavily rolled iron has been studied in detail by Bennewitz.~ The texture consists primarily of a partial fiber texture about a (110) axis in the rolling direction, designated here as fiber texture A. It includes the range of orienta- tions (111)[110] - (001)[ 110] - (11l)[110]. A weak secondary texture also is present.6 This is a duplex partial fiber texture about two (110) fiber axes located 60 deg from the rolling direction and 30 deg from the sheet normal. The range of this texture, designated here as fiber texture B, about the [101} fiber axis is (112)[110] - near (545)[252] - (211:1[011] *The range given here follows Bennewit~.~ A few pole figures from re-crystallized material indicate a broader range than this.' However, the components which are strongest in the recrystallization texture are in this range.'________________________________________________________ Primary recrystallization textures in unkilled steels can be accounted for by growth of members of fiber texture B present in the deformed metal.5 However, while members of fiber texture B dominate the primary texture, other orientations survive primary recrystallization as well. In particular, some {111}(110) members of fiber texture A must also grow during primary recrystallization, because a well-defined {1ll)( 110) texture develops during subsequent grain growth at 700°C.5 The unusual recrystallization behavior of deformed supersaturated solid solutions has been attributed to: 1) retention of the solute in solution,' 2) formation of coherent, preprecipitation solute clusters prior to and during re~r~stallization,~ and 3) formation of a precipitate prior to and concurrent with recrystallization.'~-'~ When aluminum is supersaturated with iron, the difference in grain boundary mobility between general high-angle boundaries and certain special coincidence site boundaries is apparently eliminated.' In aluminum-killed steels, precipitation of A1N can take place at ordinary subcritical recrystallization temperatures. The rate of precipitation increases with increasing aluminum or nitrogen contents.2'13 There is some doubt, however, as to whether true precipitates form during the time at temperature needed to complete recrystallization. Leslie ef a1.2 found that precipitation in one steel was complete after about 100 min at 700GC, or after about 1000 min at 650GC, as measured by chemical analysis for AlN. Aoki et a1.,13 using internal friction for dissolved nitrogen, showed that a large fraction of the dissolved nitrogen was removed from solution within a few minutes annealing time at temperatures from 400" to 800°C. However , the rate of formation of AlN, as detected bv chemical analvsis. was much slower than the apparent rate of nitrogen removal. Hasebe,'~~ using carbon extraction replicas, has identified A1N precipitates by electron diffraction in a 0.2 C steel, solution-treated at 1300°C and annealed 2 hr at 700°C. Borchers and kim,I6 also using a replication technique, observed precipitates after annealing treatments as short as 2 min at 640°C. However, Leslie et a1.' state that no A1N precipitate can be seen while recrystallization is being inhibited in aluminum-killed steel.

Jan 1, 1967

By Beatrice Lukens, David Schlain, John D. Prater

"The electrolytic manganese process4/ developed by the Bureau of Mines involves the electrolysis of a solution of manganese sulfate and ammonium sulfate in a diaphragm-type cell. Metallic manganese is deposited on the cathodes, and sulfuric acid is produced at the anodes. The spent electrolyte contains, in addition to the sulfuric acid, approximately 40 percent of the manganese sulfate and most of the ammonium sulfate originally present in the feed solution. This spent solution is used to leach fresh ore that has previously been subjected to a reducing roast. The resulting leach liquor is purified and returned to the cell.Manganese of very high purity is produced by the electrolytic process. The properties of this metal are so different from those of the best grade of manganese that can be made by any other commercially feasible process that it is virtually a new material. Electrolytic manganese has been used in the preparation of new high-manganese alloys with valuable properties.3/ and further developments are to be expected. The electrolytic manganese process not only results in a product of superior qualities, but is applicable to large tonnages of domestic ores that are unsuitable for direct use in producing ferromanganese.The future industrial use of electrolytic manganese is of course, related to its cost. Decreases in the cost of production will lead to wider use of the metal; conversely, increases in the volume of production made possible by greater demand will bring further .decreases in cost."

May 1, 1946

Study on Rational Process Flow Sheet for Beneficiating Low-Grade Cu, Mo, Bi, S, W Polymetallic Ore

Sep 13, 2010

The Martha deposit is an economic giant epithermal gold deposit, with mined and unmined resources of more than 218 000 kg (7 Moz) Au. The Au-Ag, base metal sulphide-bearing quartz lodes in the Martha deposit form an extensive braided pattern within hydrothermally altered andesite wall rock. There are five main quartz lodes: 1.      Martha, 2.      Welcome, 3.      Edward, 4.      Empire, and 5.      Royal.   Information from historic mine plans and reports has been used to determine the depth distribution of economic ore within the Martha deposit. Economic ore (average of 10 g/t Au) in the Martha underground mine was at a maximum width and strike length between a vertical depth of 160 and 350 m. Below this depth the quartz-sulphide lodes continue, but the grade declined to sub-economic grades (< 4g/t Au) at about 575 m depth and economic ore shoots were localised, mainly on the hangingwall side of the lodes. Samples from exploration drill holes indicate that this decrease is associated with a depth zonation from electrum-bearing Zn-Pb-Cu-Ag sulphide ore (average 10 g/t Au) to sub-economic (< 2 g/t Au) electrum-poor Zn-Pb sulphide mineralisation.

Jan 1, 2006