Search Documents

By J. F. Wilson

An experimental investigation has been made of gas-driven slug displacements in a system of high gas saturation to evaluate the process for use in a California reservoir. Fluid compositions, temperature, pressure and core permeability duplicated reservoir conditions as closely as possible. The temperature was above the critical of the slug materials. The slug composition required for 100 per cent oil recovery in the linear flow systems was found to agree with that determined from equilibrium phase studies. A qualitative theory for the slug displacement of two-phase systems is proposed and found to be in general agreement with the observed flow behavior. The theory predicts that the length of the reservoir fluid-slug transition Zone will increase with increased initial gas saturation and decrease with increased oil swelling accompanying the composition change from reservoir oil to the critical composition. The precipitation of small amounts of an asphaltic phase during the formation of the transition zone had no adverse effects on the flow behavior of otherwise miscible systems. INTRODUCTION Despite the large number of recent publications relating to oil recovery by miscible displacement, little information is available concerning the behavior of crude oil-natural gas systems at conditions likely to be encountered in field application. The laboratory data reported here were obtained during an investigation of the possibility of using a gas-driven LPG slug in a partially depleted California reservoir. Seven gas-driven slug displacements employing slugs of different compositions and sizes were made in 26- to 27-ft long sandstone cores. The equilibrium phase behavior of the systems was also determined. The features of primary interest in this study are the following. 1. Data were obtained on the displacement of reservoir fluids at reservoir conditions. 2. A high gas saturation existed in the long cores at the start of the displacements. 3. The temperature of the studies was above the critical of the slug materials. 4. A comparison between the flow behavior and equilibrium phase behavior, as illustrated by a pseudo-ternary phase diagram, is afforded for a system of considerable complexity. THEORY Phase Behavior The use of the pseudo-ternary phase diagram to illustrate the phase behavior in miscible displacements has been discussed by Clark, Schultz and Shearin. Sie-vert, Dew and Conley and Arnold, Stone and Luffel' have presented both phase equilibrium and flow data for true ternary systems. For the true ternary, the application of the theory is straight-forward; for a reservoir system represented as a ternary, the theory undoubtedly gives a qualitatively correct picture. One purpose of this investigation was to see if the pseudo-ternary phase diagram could be used to predict with reasonable accuracy the conditions necessary for miscible displacements with actual reservoir systems. MiscIBLE Displacement of Two-Phase System A large number of papers "I3 have treated the miscible displacement of a single-phase fluid from both an experimental and a theoretical viewpoint. However, the normal field application of the process will be in a partially depleted reservoir. Often the state of the system will be such that the mobility of the gas phase is greater

By R. P. Beyer

As part of its thermodynamic investigations of mineral compounds, the Bureau of Mines has written an algorithm based on Newton's method for solving for the characteristic Debye temperature of a compound, from heat capacity and temperature data. A listing of a FORTRAN IV program based on this algorithm, for calculating Debye temperatures given heat capacities or for calculating heat capacities given Debye temperatures, is available from the author upon request.

Jan 1, 1981

By Youze Xu

The effect of oxalic acid, acetic acid, citric acid and EDTA on extraction of Cr (?) in soils contaminated by chromium- containing slag was investigated using a batch of incubation experiment. The results show that the pH value decreases more obvious with the increase of the amount of organic acid. The amount of Cr (?) extracted increases with increasing the amount of organic acid. When the ratio of organic acids to total Cr was 5:1, citric acid revealed the highest extraction effectiveness, followed by EDTA, oxalic acid and acetic acid, respectively. The amounts of Cr(?) extracted by citric acid, EDTA, oxalic acid and acetic acid increased by 439%, 244%, 215% and 162%.

Jan 1, 2009

By J. B. Boniwell

The INPUT electromagnetic prospecting system was originally developed by Dr. A. R. Barringer in an effort to increase the sensitivity and penetration of airborne EM methods. Although brought to an operational state some several years ago, it is only through relatively re-cent modifications and testing that some of the potential of the system has been fully realised. This is brought into perspective by some recent results over known ore deposits and geologic environments.

Jan 1, 1967

By J Webb

"It is vitally important in projects where the cut-off grade is low that there is no contamination during the sampling and sample preparation process, both in the ore and the waste zones. Failure to identify contamination could have devastating financial consequences for a project. The use of a variety of blank types is essential for ensuring that contamination is identified and eliminated at every stage of the sampling and sample preparation process. This paper examines an instance where an effective assay quality assurance and quality control (QA/QC) program was able to identify and eliminate a source of significant multi-element contamination in the prefeasibility stages of an open pit project. This examination includes the: evidence for contamination findings of the investigation process of resolving the problem and correcting the data evidence for both addition of metal and dilution through contamination potential impact on the project had this issue not been dealt with. It was through the use of a combination of blank types that the QA/QC process at Mount Isa Mines (MIM) identified a contamination issue at the first crushing phase of sample preparation. Identification of the contamination allowed MIM to stop assaying activities and work with the laboratory to correct the problem. The sampling program could then be continued with no further doubts about the sample preparation process. Contaminated samples were resampled from retained core. With the continuous monitoring provided by the blanks program, it was possible to ensure that only clean results went into the resource modelling data set. CITATION:Webb, J, 2014. When nothing is what you need – the importance of using blanks at all stages of sample preparation, in Proceedings Sampling 2014 , pp 49–54 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

By Valentine Chanturiya, Irina Khabarova, Maria Ryazantseva, Igor Bunin

"XPS investigations of the influence of HPEMP - treatment duration on the surface composition for natural chalcopyrite and sphalerite are described. HPEMP is a video pulse with a nanosecond front lasting between 5 and 10 ns. The electrical field component can reach 30 kV, whereas pulses repetition frequency is 100 Hz. In general, the formation of metal-deficient surfaces, polysulphides or elemental sulphur and oxides/hydroxides, were determined during the treatment for both sulphides as well as the essential differences of the way of mineral surface transformation during the treatment. The chalcopyrite surface shows the formation of elemental sulphur under the HPEMP treatment at 103 pulses while appearance of unstable sulphite species was detected at the chalcopyrite surface within 5 seconds (0.5•103 pulses) under the same treatment conditions. The results indicate that the quantity of adsorbed water (at.%) is changed considerably during the HPEM - treatment depending on treatment duration for both minerals. The concentration of water onto the chalcopyrite surface decreased during 30 seconds (3•103 pulses) of the HPEMP - treatment and it rose after the treatment at 5•103 pulses. The inverse dependency was obtained for sphalerite surface. Single mineral flotation tests have shown the significant increasing of the minerals recovery."

Jan 1, 2014

By Saskia Duyvesteyn

For many applications in hydrometallurgy and water treatment it would be advantageous to use ion-exchange resins in stirred reactors. However, attrition of the resin may lead to significant losses of both resin and metal values and prevent water quality goals from being reached. We have studied the recovery of fine resin particles by froth flotation, using the model copper - Dow XFS4195 chelating resin system. As the functional group on the resin is a bis-picolylamine, the resin should be amenable to flotation by anionic collectors, such as sodium dodecylsulfate and sodium dodecylsulfonate. The kinetics of copper loading from dilute aqueous solutions in an agitated vessel were studied as a function of copper concentration, pH and resin bead size. The flotation of unloaded resin was investigated for different types of collector, collector concentration, conditioning time, and resin bead size. Potential applications are discussed.

Jan 1, 1995

By Philip Drinker

IN THE mining and metallurgical industries, numerous problems arise requiring determinations of solid and of liquid particles suspended in air. Frequently, these problems are of local interest and involve purely economic or operating difficulties; on the other hand, toxic effects from the inhalation or the ingestion of substances suspended in air may be a matter of concern. For checking up process improvements or for determining ventilation efficiencies in problems of this general nature, various methods have been proposed. Although simpler methods are often satisfactory, precipitation combines several desirable features that other methods lack. This paper is, therefore, devoted to a discussion of portable alternating-current precipitators applicable to the quantitative determination and microscopy of dusts, fumes, and smokes in air. Small particles suspended in gases, such as air, are referred to in the literature as aerosols or suspensoids. Of these terms, suspensoids appears to be preferable as being more nearly in keeping with words in everyday use. In problems involving air pollution by small, particles-by suspensoids-it is convenient to distinguish three broad classes based on the size, the degree of dispersion, and the method by which the particles become suspended in the air. Dusts.-Particles or aggregates of particles, 150 to 1 micron in diameter, that are thrown into the air by mechanical agencies are termed dusts. Examples are silica, talc, cement, organic dusts such as hard rubber, starch, and cocoa; flocculated fume and smoke products. Fumes.-Particles, 0.2 to 1 micron in diameter, formed from chemical or physicochemical reactions are known as fumes. Examples are ammonium chloride, lead and mercury, zinc and magnesium oxides, fogs, and acid mists.

Jan 3, 1925

By F. Mucciardi

While flash smelting and converting are capturing a greater share of the market, injection through circular injectors will remain with us for the foreseeable future. The use of top lances for injection is a key feature in several processes (e.g. Mitsubishi, Ausmelt). Tuyeres, on the other hand, are incorporated into a number of processes (e.g. Noranda, Peirce-Smith). To date no lances or tuyeres are cooled by an external source. The reagent provides the bulk of the cooling. With limited cooling, it is normal to have substantial wear on the nozzles - especially in the case of lances. To overcome the issue of wear, a new patented injector (lance or tuyere) has been developed by Noranda and McGill University. This novel unit is based on heat pipe technology. It can operate for an extended period of time without wearing. Enhanced lance/tuyere life is achieved by operating the injector at a low enough temperature that promotes the formation of a thin frozen layer on the outer body of the unit. The vaporizing and condensing substance within the unit acts to cool' the high heat flux portions and dissipate the heat to areas of low heat flux outside the vessel. A fairly large number of tests have been conducted with a prototype unit. The tests have shown that the heat pipe lance is a viable unit. In this paper is detailed a test which illustrates how the lance functions when pure oxygen is injected into copper matte. In addition, the findings from a basic study of a heat pipe in high heat flux environments are also presented.

Jan 1, 1999

By Langtry E. Lynd

Ilmenite concentrates prepared from beach and dune sands of Florida, India, Australia, and other localities deviate to varying degrees from the theoretical composition of pure ilmenite, and generally contain more Ti02 than the formula FeTiO3 would indicate, and some Fe203. This variation in composition is due to different amounts of altered ilmenite in the concentrates.(l) The alteration has been shown to take place by oxidation and leaching of the iron in ilmenite, to yield residual products consisting of amorphous or very finely crystalline titanium dioxide and ferric oxide, Other studies (2) have stressed that ilmenite may alter first to an amorphous titanium-iron oxide, or to an amorphous mixture of titanium and iron oxides, with later alteration to crystalline titanium dioxide. There has been some speculation as to whether alteration of ilmenite is usually caused by weathering or by hydrothermal processes,(3, 4, 5) Three main methods of approach were used to study the mechanism and rate of ilmenite weathering, (1) Etch tests were used to learn the relationship between crystallographic orientation and the rate of chemical attack on ilmenite. (2) Altered ilmenites in New Jersey sands were compared with ilmenite in rocks of the area from which the sands were probably derived, (3) Experiments were carried out to determine at what rate, and by what agents, originally fresh ilmenite could be altered in the laboratory under simulated weathering conditions.

Jan 1, 1959

By John J. Sammarco, Edward F. Fries

This report (Independent Functional Safety Assessment 4.0) is the fifth in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 5, 2003

By Michael Clar

Total suspended solids (TSS), generally referred to simply as sediment, is one of the four major parameters of water pollution associated with surface mining activities. The other three para¬meters are iron, manganese and pH. Currently the Environmental Protection Agency (EPA) is in the process of developing and implement¬ing effluent limitations for these pollutants pursuant to section 301 of the Federal Water Pollution Control Act Amendments of 1972, 33 USC 1811.1 To date, effluent guidelines for existing point sources have been published, and guidelines for new sources are forthcoming. The effluent limits which have already been developed for TSS have been subjected to some controversy.1 Some industry spokesmen have indicated that they may be unable to meet these effluent limitation guidelines for TSS. The industry claims that in certain areas the suggested limit is unattainable since high suspended solid loads already exist in streams due to numerous and various sources of nonpoint pollution which include agriculture, silviculture and urban construction for which no TSS effluent limits have been set. An opposite viewpoint asserts that the TSS limitations are too lenient since permit data from the Regions (U.S. EPA Regions) indicates present compliance for several companies under more stringent TSS limits. The experience at the Centralia mine in Washington is one example.2

Jan 1, 1977

By Robert M. Mann

The Ag/S specific ion electrode has been evaluated for analysis of both free and total cyanide. Metal cyanide solutions were prepared from reagent grade compounds and by stoichiometric fixture of the metal with a potassium cyanide solution. Solutions containing Cu+1, Ni+2, Fe+2, Fe+3 and Zn+2 complexes were analyzed prior to and following EDTA pre treatment. This effort provides an understanding of the effect of each metal cyanide complex on the SIE analysis of free and "total" cyanide.

Jan 1, 1981

By M. Soderstrom

In a solvent extraction (SX) plant, stage efficiency calculations are used to determine mixer efficiency. With modern extractants and mixing equipment, it is generally taken for granted that stage efficiencies will be above 95%, but this is not always the case. Dependant on mixer/solution conditions, stage efficiencies can occasionally be low, therefore leading to higher reagent usage. Proper methods to identify when stage efficiency performance is below expectations, and ways to identify if it is an equipment or chemical issue are valuable tools for a plant metallurgist. With these tools and skills an on-site metallurgist can more quickly return their SX plant to proper operation. This paper will discuss methods for analyzing stage efficiency, evaluating factors that may affect stage efficiency, and evaluating the impact of stage efficiency on the overall operation.

Jan 1, 2010

By Richard H. Oitto

With increased interest and urgency for coal mine safety and the passage of the Federal Coal Mine Health 'and Safety Act, the Bureau's research effort in roof control has been greatly expanded. One new project, the subject of this paper, concerns improving conventional roof bolting and has been involved with the effects of different variables on the performance of roof bolt expansion anchors. These include types of expansion anchor, rock type at the anchorage horizon, borehole roughness, rate of torquing a roof bolt to set the anchor, installed tension, bolt length, and relative humidity fluctuations. For this work, two types of experiments were carried out. One was concerned with tension loss in bolt-anchor assemblies and simulated anchor performance in a static roof. The other dealt with anchor slippage as tension was increased and simulated anchor performance in an active roof. Trials were made in the laboratory under controlled conditions so that factors suspected of affecting expansion anchor performance could be selectively studied. Because of the natural variability in rock and the fact that most expansion anchor components are essentially rough castings or forgings, the experiments were designed to permit using analysis of variance techniques for analyzing data. Thus, in this paper, "significant" means statistically significant.

Jan 1, 1972

By Matthew Kowalczyk, Steve Bloomer, Peter Kowalczyk

"Mineral deposits found near seafloor hydrothermal venting are of great economic interest. Valuable metals such as gold, copper, zinc, and other polymetallic sulfides are found in appreciable grades in seafloor massive sulfide (SMS) deposits associated with these vents. For mapping these deposits, electromagnetic prospecting is one geophysical method that is very useful because copper/gold rich deposits are highly conductive.Ocean Floor Geophysics (OFG) in 2008 developed the first EM system to successfully map the limits of conductive mineralization in a survey at the Solwara 1 deposit (Kowalczyk, 2008). Since then, towed coincident loop time domain systems have been developed by Waseda University (Nakayama and Saito, 2016) and have successfully detected known mineralization buried at 30m depth. Using a deep tow controlled source electromagnetic (CSEM) array, very clear anomalies have been measured (Murton, 2017) over known mineralization at the TAG field on the mid-Atlantic ridge.In 2014 and 2015, OFG partnered with Fukada Salvage and Marine Co. Ltd. and the Scripps Institution of Oceanography to map methane hydrate deposits off the coast of Japan using a towed controlled source electromagnetic (CSEM) system developed by Scripps. These hydrate deposits are resistive targets, and the Scripps system successfully mapped subsurface electrical resistivity distributions to depths of several 100 metres below the seafloor. OFG is attempting to extend the Scripps CSEM technology to map subsurface conductive SMS deposits to a similar range of depths below the seafloor."

Jan 1, 2017

By J. Petersen, H. Naderi, M. H. Nikzad, M. Karimi

In this research, the thermodynamic study of sodium persulfate (Na2S2O8) solution in the presence and absence of H2SO4 and Fe3(SO4)3 was done. Eh-pH and equilibrium distribution diagrams were constructed using Outotec HSC Chemistry Software and the main stable ionic species were determined. Also, the mean activity coefficient and Pitzer model coefficients were evaluated. Effects of system composition, sodium persulfate concentration and temperature were investigated. According to the results, HS2O7 -, HS2O8 -, S5O3 2-, S4O3 2-, S3O3 2-, HS- and NaSO4 - are the main stable species in these three systems. Increasing of sodium persulfate concentration resulted in disappearing of SO4 2- and the appearance of NaSO4 -. The main effect of increasing the temperature from 25 to 75oC, is changing the stability regions of HS2O7 -, NaSO4 -, SO4 2- and S2-. From equilibrium studies, it was concluded that at 25 and 50oC, increasing the persulfate concentration results in a 55-60% decrease for HS2O7 - and an 20- 30% increase for HS2O8 -. At 75oC, HS2O8 - becomes the main species and its percentage decreases with increasing the persulfate concentration. Keywords: Thermodynamic, sodium persulfate, activity coefficient

Jan 1, 2020

By Ulf Svensson, Donald E. Zipperian

This paper reviews commercial installations of FLOTAIRE Column Flotation Machines for metallic, nonmetallic, and coal flotation. Second generation FLOTAIRE Column Flotation Machines employ dual aeration systems to provide a mixture of air bubble sizes. Operating data presented in this paper shows that optimum grade and recovery relationship for each rougher, cleaner, and scavenger application are obtained by adjusting the ratio and volume of aspirator air bubbles and micro diffuser air bubbles.

Jan 1, 1988

By F. P. A. Robinson, J. W. Fourie

Austenitic stainless steels are welded using low-heat inputs. However, owing to differences in the physical metallurgy of austenitic stainless steels and duplex stainless steels, low-heat inputs should be avoided for duplex stainless steels. This paper highlights the differences in solidification mode and transformation characteristics of these two types of alloys. Recent work on the effect of heat input on the properties of weldments of duplex stainless steels is reviewed.

Jan 1, 1990

By A. E. J. Gallagher

This report summarizes the results of flotation studies conducted by the Federal Bureau of Mines on samples of extremely fine-grained lead-zinc sulfide ores. Samples from five ore deposits in the Pine Creek area, Coeur d'Alene district, Idaho, and one deposit in the Metaline district, Washington, were studied at the Albany Metallurgy Research Center to determine the recovery of sulfide lead and zinc by flotation. During the investigation it was found that flotation could be effectively applied to the selective recovery of exceedingly fine-grained lead and zinc sulfide minerals. Separation of galena and sphalerite was obtained on pulps ground through 1,600-mesh, in which most of the particles were smaller than 5 microns. Selectivity and recovery of minerals in this fine size range were enhanced by use of a chemical dye, diphenylthiocarbazone, as a galena promoter. Although unsuccessful on one ore, application of the dye in treatment of two other very fine-grained ores yielded lead concentrates containing over 62 percent Pb at recoveries in excess of 85 percent. More than 55 percent of the lead in these concentrates occurred as particles smaller than 2 microns.

Jan 1, 1961