Search Documents

By C. Maree

Paper written on project work carried out in partial fulfilment of B. Eng (Chem. Eng.) This paper describes the development and use of a process simulator to optimize gypsum recovery at Afmine, a small plant near Yzerfontein on the South African West Coast. The simulator consisted of models of the major plant equipment, viz. hydrocyclones, surge bins, settling tanks, a primary sieve and a dewatering screen. Experimental data suggested that the equipment could be modelled satisfactorily from data published in the open literature. Simulation studies have indicated that gypsum losses on the plant could be reduced substantially by means of some relatively minor modifications to the plant layout. Moreover, sensitivity analyses of the plant have indicated that optimization of the settling tanks should receive priority over the other process units.

Jan 1, 2005

By Damon P. Vandermaat

Coupon testing allows for the rapid understanding of a material?s likely behavior in service conditions, allowing engineers and operators to make informed decisions about the likely service-life of parts when subjected to field conditions. Bend testing has been identified as the best approach for exploring rock bolt susceptibility to stress corrosion cracking (SCC) in underground mining. The bend test specimens used were 2?3 mm thick slivers of steel, cut from the outer edge of a rock bolt. For the specimens, 1350 grade steel was chosen due to its wide use in the industry. The jigs themselves are small assemblies made of stainless steel that are capable of imparting a bending load on the specimens. The jigs were installed at a coal mine located in the Western Coals West of Sydney, Australia, in such a way as to expose the test specimen to water dripping from the mine roof. It is expected that this approach will yield results pointing to the likely SCC mechanisms affecting the service life of rock bolts, as well as demonstrate the jigs? usefulness as an early warning system for SCC. Furthermore, the coupon tests will be correlated against the results of large-scale laboratory tests.

Jan 1, 2012

By H. Kotzé

Ticor SA began with a detailed feasibility study in 1995. The Hillendale mine (situated between Richards Bay and Empangeni) and mineral separation plant were approved in 2000. The smelter, just outside Empangeni, consists of two 36 MW DC arc furnaces that were commissioned in 2003. Experiences gained during the initial commissioning of the furnaces proved valuable in later commissioning work, as shown by the increase in ramp-up rates. The capacity of the plant is 250 kt/a TiO2slag and 145 kt/a of pig iron.

Jan 1, 2006

By B. A. Ridolfi, S. M. Alvarez

The Moon Creek Reclamation Project provides a case study in the development of creative cleanup solutions for an abandoned lead and zinc mine and mill site located in northern Idaho. Innovative design features include construction of a 88,000cubic yard combined waste containment facility on soft in-situ tailings, water-balance cap, limestone gravel drains, a geocell mattress for stability, and a below-grade scour protection berm. The stream, including a wetlands buffer, will be relocated within an existing road alignment and rehabilitated to provide trout habitat. These elements allow for the integration of reclamation and stabilization measures into an effective site design.

Jan 1, 1999

By G. J. Feng

Based on detailed theoretical analysis of coarse floatation and three-phase froth, a laboratory system which contains a new type of froth floatation equipment is established. Through water experiment, the relationship among floatation dynamics parameters of the equipment is studied and the best work parameters are educed too. Based on all of above, Slurry test is carried out in a copper concentration plant. Granule between 0.28~0.45mm can be reclaimed successfully. The slurry test proves that to separate coarse minerals in froth floatation equipment is a kind of effective method, it is well worth to make a further study.

Jan 1, 2014

By T. S. Lovering

The use of geothermal energy is expanding very rapidly. This type of energy has proven commercially profitable for generation of electricity, for space heating, process heating, auxiliary heating of water in conventional steam power plants and for recovery of chemicals contained in natural hot water and steam. Two types of geothermal energy sources are recognized: 1) hot springs in regions of nearly normal heat flow that tap a deep reservoir through which water moves slowly to a hot springs conduit and then rapidly to the surface; 2) hyperthermal areas in which the water is heated by a relatively concentrated heat source related to volcanicity. If there is a geologic trap that provides a geologic analog to a steam boiler, as at Larderello, Italy, the hyperthermal area will have a convecting system that develops superheated water at relatively shallow depth and may provide natural steam in large quantities. If a hyperthermal area is to be productive for a long time, the underflow into the reservoir should be slow enough to allow the heat source and convective system to heat the underflow to the working temperature, and the production rate must not exceed this rate of underflow. A model based on a typical aquifer suggests that the rate of movement of water through the reservoir be such that a few years are spent in transit between isotherms that are spaced about 2°F apart. The possibility of finding blind geothermal areas is illustrated by discussion of the techniques developed in evaluating the subsurface temperatures in the East Tintic district of Utah where a map of isotherms at water level (2000 to 2000 ft below the surface) shows that a hyperthermal area may exist a short distance southeast of the mining district. Very nearly all of the energy that man currently uses comes ultimately from the sun's radiation. This includes water power, fuels such as wood, peat, coal and petroleum, the wind and all our animal power. In the paper summarizing a conference on solar energyl6 the average amount of solar energy received daily on the earth is taken at about 1 cal per m2 per min or slightly less than 2 pcal per cm2 per sec; this is almost exactly the amount of energy on the average that the earth liberates in regions of normal geothermal gradient due to its own internal heating. In many places, however, the energy released is many times the average and in some of these hyperthermal areas, geothermal steam is used for generation of electricity, and hot springs are used for heating buildings and private dwellings, process heating, auxiliary heating of water in conventional steam power plants, and chemicals may be recoverable from both hot water and steam. The use of hot springs waters for heating houses goes back hundreds of years but until recently was confined to a few dwellings close to the hot springs. In Korea, some houses had hot spring water channeled through conduits in the floor centuries ago and thus the Koreans can be credited with pioneer development of radiant heating. In Iceland at present nearly a third of the population uses natural thermal water for domestic heating." The Reykjavik system pipes hot spring water at about 94°C throughout the city and has devised insulated double pipes that allow the water to be piped for some 25 km with a drop of only 1°C for every 5 km. The actual cost to the Icelandic consumer is only one-third the cost of heating by imported coal and yet the industry is one of the most profitable in Iceland. The most profitable use of geothermal energy has been its conversion into electricity which can be transmitted economically much greater distances than hot water. The largest installation at the present time is that at Larderello, Italy, where the Count of Larderello began to experiment in the production of electricity from geothermal steam 60 years ago — in 1904. He installed his first steam turbine, with a capacity of only 250 kw, in 1912 as the result of a local quarrel with the power company which furnished the current required in the Larderello chemical industry - an industry that then dated back nearly a century. As experience was gained in drilling deep holes to tap geothermal steam and in converting it to electric power, the capacity of the installation of Larderello gradually increased, but was all destroyed by the Germans during their retreat from Italy in the closing

Jan 1, 1965

By Frik Badenhorst, René Roux, Peter Terbrugge

This paper presents a case study where economics dictated an aggressive slope angle and where an appropriate slope management programme allowed successful completion of mining to 190m below surface. The Navachab Gold Mine is located in Namibia and is one of the few gold mines in that country. Mining by open pit methods commenced in 1990 with economics dictating an aggressive slope design to minimise waste stripping and make the mine viable. With steep slope angles in the design, and a steeply dipping footwall geology, it was necessary to introduce a comprehensive slope management programme. This required good mining practice in limit blast techniques with pre-splits and trims, and good housekeeping to effect a safe and economical operation. The slope management programme in addition required in pit mapping and logging procedures, regular survey monitoring evolving to a robotic Geomos system, as well as slope instrumentation to monitor stability. Two relatively large scale failures occurred at the mine, the second of which impacted on the east wall access ramp, while the first was confined to an operating stack. The paper describes the design and slope management techniques developed for the east wall.

Jan 1, 2006

By L O. Filippov, C H. Veloso de Melo, A Correa De Araujo

Froth flotation of iron ores is one of the most widely used methods to upgrade iron ore into high-grade concentrates. In recent years, reverse cationic flotation of iron ores has been specifically the subject of several studies. Since quartz is the most common gangue mineral in iron ores, understanding the behaviour of this mineral was the main target of the majority of such studies. However, with the depletion of mineral deposits considered rich and easy to process, it has become more common to find iron ores with complex gangue minerals, which are composed not only of quartz but by a variety of silicates. The mineralogical composition of the ore is an important factor for determining reagents and mineral processing parameters. The mineralogical suite of an ore also presents a paramount role for operational optimisation of any given flotation process. Some studies were performed with different types of amphiboles and other Fe-bearing silicates, for example, but the influence of the mineralogical nature of these silicates in reverse cationic flotation has not been fully explored and will be discussed here. Changes in the traditionally used reagent scheme for reverse cationic flotation, generally including alkaline pH values, polysaccharides as depressant (mainly starches) and primary ether amines and diamines, are expected when dealing with iron ores with complex silicate gangue composition.CITATION:Veloso de Melo, C H, Correa de Araujo, A and Filippov, L O, 2017. Reverse cationic flotation of iron ores with complex silicate gangue minerals, in Proceedings Iron Ore 2017, pp 241–244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By P L. McCarthy

To design and operate a successful mine the technical specialists must agree on what is ore, what is not ore, and how quickly the orebody is to be mined and processed. These seemingly simple questions defy easy analysis and can push mining engineers, geologists, metallurgists and others to the limit of their capabilities. The questions are rarely addressed adequately in feasibility studies or in operational planning. To optimise the mine and processing plant requires proper determination of cut-off grades or values, prediction of feed variability on an hourly, daily or longer basis, right-sizing the mining rate for optimum product quality, understanding the cost of capital and the expectations of investors, and many other considerations that involve geology, geotechnical engineering, mining, metallurgy, environmental effects and economics. This paper addresses the key matters that should be considered as inputs to the practical issues of metallurgical plant design and operation.CITATION:McCarthy, P L, 2015. Integrated mining and metallurgical planning and operation, in Proceedings MetPlant 2015, pp 35–45 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Cary Hirner, David Stacey, William A. Rochford

Design considerations and construction techniques were implemented to address groundwater infiltration from a confined aquifer during the excavation and lining of the Cady Marsh Flood Relief Tunnel. This 3-m finished diameter, 2-km long tunnel was successfully completed cost-effectively in an urban setting near East Chicago, Indiana. The soft ground was mined using a conventional tunnel boring machine with hydraulically actuated flood doors and supported with steel ribs and timber lagging. The tunnel was lined with cast-in-place concrete. Dewatering was implemented in settlement prone, boulder-laden ground in residential neighborhoods during construction to depressurize and partially dewater the aquifer at the tunnel horizon. This paper describes the design decisions and construction methods utilized to mitigate and limit infiltration into the tunnel during construction and operation, as well as manage ground settlement.

Jan 1, 2007

By R. L. Amelunxen

"In January 1983, Gibraltar Mines Ltd. started an exploratory program on Column Flotation with hopes of improving performance of the Molybdenum Cleaning circuit. The encouraging results led to a column test trial in the Bulk Copper Cleaner circuit where the test unit has per¬formed well. A program was undertaken to understand the mechanics of column operation. A year and a half later, Gibraltar is considering the replacement of existing Bulk Copper and Moly Cleaning flotation cells with a fully computer con¬trolled Column Flotation circuit.BRIEF SUMMARY OF TESTWORKInitial testwork was done with a home made 20 inch diameter x 31 foot high column, equipped with a doppler flow-meter at the tail line and automatic level conrol. This loop maintained constant level in the column by throttling the tail valve. This column was placed in a variety of locations around the Moly circuit as shown on Figure 1 a, b. Test re¬sults indicated that the column could achieve much higher grades than the conventional cells, but recovery wise, the performance was low. Spillages from overloaded pump boxes were a common frustration during this time.Column control strategy was reviewed; and, in light of information received from McGill University, changed to conform with the methods that had been employed by D. Wheeler, of the Column Co. of Canada4 and Gaspe Copper Mines3.The column was tested replacing a portion of the bank, figure lc. The results obtained were more or less equal to the circuit. However, as we had Nitrogen gas connected to the column and not the regular cells, the column was kept in service. With the use of Nitrogen in the column, the usual copper depressant, Sodium Cyanide could be replaced with Sodium Hydrosulphide, hence lower operating cost.As time went on, a 10 inch diameter column was added in series to re-treat the concentrate of the 20 inch diameter column with hopes that the copper content would decrease from 0.6% down to 0.3% in order to save on subsequent leach¬ing costs. So far, results indicate there has been some im-provement, hut we are not achieving 0.3% copper. (See figure 1d)."

Jan 1, 1985

The coalmining industry in most countries has, at various times, suddenly been confronted with a decrease in demand for coal. Readjustments made to reduce productive capacity to match the reduced demand for coal have often resulted in hardship to mineworkers, loss of capital investment to mineowners and loss of coal reserves. The consequences of the methods of readjustment adopted in the past have contributed to the low esteem in which coalmining has come to be regarded by a large section of the gel).eral public in many countries.Four sections of the coalmining industry, representing different periods of time, different countries, and different methods of industrial organisation have been examined:Great Britain and the U.S.A. during the inter war years, the post war European Coal and Steel Community, and post war Great Britain under the National Coal Board. An assessment has been made of the methods adopted in each case to reduce productive capacity to match a reduced demand for coal. Finally the fundamentals of the problem-as it affects the coalmining industry of any country-are considered, and possible solutions put forward.During the 1950's, surplus productive capacity was a problem in many coalmining countries, including Australia and New Zealand. As a rule no techniques are developed beforehand to solve problems introduced by a sudden decrease in demand for coal. The situation is usually tackled by a series of short term decisions based on expediency, which often in the long run only aggravate the problem.

Jan 1, 1961

"The link between ore texture and mineral liberation has previously been established at a microscopic scale. To construct ore texture models that can be used in mining applications requires this relationship to be retained at a significantly larger scale. This is initially dealt with by finding a basic set of microtextures that form the elements of the ore textures at the next larger mesoscopic scale, simulating these mesotextures at a fine scale, then changing the support of the mesotexture simulations to generate the expected mining block/stope mesotexture distributions. Thus, a mutually exclusive and exhaustive set of spatially locatable mesotextures can be used to fully characterize the metallurgical properties of in situ material.A method that generates expected distributions of mesotextures for any mining block size or shape is proposed, and includes: (1) characterizing the spatial correlation of the set of mesotextures with a single covariance function; (2) generating multiple simulations of mesotextures at a fine scale; and (3) using the simulations at a fine scale to generate the expected mining block/stope mesotexture distributions. A case study, using the George Fisher sediment-hosted base metal deposit in Queensland Queensland, Australia, is developed to demonstrate the proposed methodology as well as show the inadequacy of off-the-shelf approaches.Mining-scale texture models can be used to improve the in situ discrimination of ore from waste by exploiting the joint spatial variability of grades and textures to quantify the expected metal recovery of in situ material, then calculate local marginal cut-off grades. An artificial case study is presented to demonstrate the changes in ore/waste selection when considering ore texture models compared to constant metal recoveries."

Jan 1, 2005

By H. R. Hammond

The situation of The Consolidated Mining and Smelting Company of Canada Limited, or Cominco, may be somewhat unique in that the Company is not only a manufacturer of ammonium nitrate, but as a mining company is a major user of its own product. This situation has resulted in highly successful application of ammonium nitrate-oil explosives. Several noteworthy techniques have been developed and others have been improved. Use of this material in the mining industry has led ammonium nitrate producers to adopt the term nitro-carbo-nitrate or INN for ammonium nitrate-oil blends. A small blending plant at Cominco's largest mining property, the Sullivan Mine, at Kimberley, B.C., is producing more than 80% of all the explosive used at the Sullivan, and is supplying two other Cominco mines. Application has required intensive research to determine the best forms of ammonium nitrate for use in small holes drilled for development and long-hole stoping. It has led not only to experiments to determine the best blending oil, but also to development of loading techniques to the point where NCN is being moved through loading tubes over 700 feet. It has required research into mining practices such as hole arrangement and blasting of development cuts. It has resulted in the development of a special product for secondary breaking. All this has been accompanied by the recognition of the importance of insuring safe practices at every stage.

Jan 1, 1963

By R. Pixler

Arch Mineral Corporation and Rocky Mountain Energy's Medicine Bow Mine in Wyoming presented an interesting challenge to the concept of mining a multiple-seam, dipping coal in the Hanna Basin. The 3362 and 2962 pits at MBCC were designed in a multiple seam coal consisting of 4 (and in some areas 5) bands of coal; these coal beds are all in the Ferris formation. The area was subject to some localized faulting and a major fault caused a physical restraint that we mined up against in our final cut. Using a 1570 dragline as the principal stripping machine, the concept of developing a bench for stripping the lower seams from the low-wall side of the pit was initiated. The results of this method of stripping were very satisfying for this pit through the completion of pit life and prompted us to use it in other areas at MBCC and at our other operations. Mining a dipping coal presents a small twist to conventional "flat" coal stripping. The spoil has a tendency to continually try to slide into the pit and the increased overburden on each cut as you mine down the dip creates spoil problems unless adequate design provisions are made prior to stripping.

Jan 1, 1986

By W. E. D. Jr. Stokes

THE application of aviation to mining and petroleum operations, on the basis of economy and attainment, has become a demonstrated fact. According to Dominion Government records, 30. Canadian companies engaged in air transportation with northland mining camps, carried 13,000 tons of freight in 1935, and in 1936 carried 16,000 tons. In addition, many mining companies used planes to transport prospectors with canoes, outboard motors, gasoline drums and supplies to remote locations, and one company maintained a plane to take radium-bearing ore from its mine on Great Bear Lake nearly 1000 miles south to the rail-way at Waterways, Alberta. Heavy pieces of mining machinery weighing 2 tons are being carried by Ford trimotor planes over the Andes, at an altitude of not less than 15,000 feet. At Bulolo, New Guinea, 17,500 tons of disassembled gold-dredging equipment has been flown over inaccessible terrain, while supplies and building materials for a, community of 1000 whites have been transported by airplane. A 3 1/2-ton shaft was carried on one notable trip, while at another time an automobile, 2 tons of rice and a large safe went over the mountains in one plane. Fig. 1 shows an electric generator that was carried by plane to Bulolo.

Jan 1, 1937

By R. J. C. MacDonald

"The first recorded discovery of placer gold in Canada was on the Chaudiere River in Quebec's eastern townships in 1832 and the first major production came from placer deposits in British Columbia in 1858 (Verity 1974). Placer deposits were the major source of gold until the late 1890's, although lode deposits were found in Nova Scotia in 1862. In 1896 the Klondike Gold Rush commenced with the discovery of gold by Henderson and Carmack in the Yukon. The peak was reached in 1900 when over one million ounces of gold valued at approximately $22.3 million were recovered. With the exhaustion of the easily accessible deposits, more capital intensive operations were necessary such as those initiated in 1906 by the Yukon Gold Corporation. This giant dredging operation continued to produce until 1966. Today only a few small operations remain.The development of Canadian lode gold mining began in earnest around 1900 when the railroads were opening up the interior and western part of the country. At this time many discoveries occurred, particularly where mineral outcroppings were near surface. Tremendous impetus for exploration and the reopening of former producers followed the elimination of the gold standard by Great Britain around 1931, and more importantly the United States in 1933, with subsequent stabilization of the price of gold at $35 per ounce in 1934. Prior to this the price of gold was basically unchanged since 1717, approximately, $20 per ounce (Verity, 1974; Green, 1973).The depression of the 1930s adversely affected most industries, however for the gold producers it was a very profitable time. Prices of materials and equipment declined and labour was cheap and plentiful. Interest in gold mining was further stimulated in 1936 when a three year tax exemption was declared for all new metal mines. In 1938 a decline in the value of the Canadian dollar relative to the U.S. dollar benefitted the industry. The second world war provided yet again further incentive for gold production and in 1941 Canadian gold production reached a high of approximately 5.4 million ounces. This figure was not surpassed until 1991 when approximately 5.6 million ounces were produced (Natural Resources Canada, 1996 )."

Jan 1, 1998

By Wolfgang G. Brunner

The closing of the gap in the European waterway- net is one of the big and challenging traffic projects following the German reunification. The water canals in the North German plain connect the Rhine river, the border between Germany and France, with the Oder, the German border river to Poland. As early as in the 30's of the 19th century the planning and construction of a ship- lift and a canal bridge started, in order to close this last big gap in the system between the Mittelland Canal and the Elbe- Havel Canal near Magdeburg. This main waterway connects the West of Germany, known for its coal mines and steel mills, with the capital Berlin, and from there it goes on into Poland. The building activities started in 1934 but came to a complete stop in 1942 because of the war. The communist government in East Germany was not interested in continuing this huge project, including the ship lock Rothensee, the canal bridge crossing the river Elbe, the former border river between West and East Germany, and the lock Hohenwarthe due to lack of political backing along with low construction capacity. Now this important project is in progress and this report describes the special foundation techniques used on the great ship lock Hohenwarthe. Hohenwarthe is a double- bay ship lock of considerable scale, which is notable for recirculating water rather than letting it flow. It includes 44 800 m2 ( 481 720 sq. ft) of up to 55 m ( 180 ft) deep cut- off walls, ground water control, 1248 bored piles with a depth of 22 m ( 72 ft ) serving as foundation and 28 000 m ( 91 864 ft) of soil densification with vibroflotation equipment for ground improvement. In the year 2003 the project shall be completed and all ships can travel from the West to the East through Germany without expensive and time- consuming detours through other canals and locks.

Jan 1, 2000

By Jos. J. Walsh

Ventilation within a coal mine is essential to the welfare of those employed therein, from the standpoint of health, safety, and efficiency. While the saving of life and the preserving of health are the chief reasons for ventilation, efficiency and production are increased. In spite of the fact that we speak of air as having a certain composition, the proportions of oxygen, nitrogen, and carbon dioxide are not fixed, but vary between small limits. The different elements are not chemically united, they are merely mixed and each is free and can be separated with little energy. For this reason air in the mine workings is seldom found in a pure state. Factors that necessitate ventilation in coal mines are those that change the composition of pure air. Contamination of mine air results from the burning of oil-fed flames, the use of explosives, the oxidation of coal, and the liberation of gases by the coal. The extent to which these factors exist governs the size and general plan of the ventilating applianccs required. An efficient ventilating system is one that will furnish air at the working faces in sufficient volume to dilute and render harmless noxious gases and at the same time maintain an oxygen content closely approaching that of pure air. In a well-ventilated mine, the oxygen seldom falls more than 0.5 per cent. below normal. The carbon-dioxide content of the air in the average coal mine will vary from 0.1 to about 0.8 per cent., which amounts are not harmful. Three per cent. of carbon dioxide in air doubles the frequency and the depth of breathing; it is plainly noticeable and if breathed continuously for several hours its effect would probably be harmful. Slight reductions in the oxygen content of the air, such as occur in well-ventilated mines, have no debilitating effect on the worker. A person not exerting himself would fail to observe any unusual physical effect in an atmosphere: containing 17 per cent. of oxygen. This condition, however, or even a condition showing an oxygen content below 20 per cent., would indicate poor ventilation and that the elements which tend to reduce the efficiency of the worker are present, namely water vapor and a high wet-bulb temperature.

Jan 1, 1923

By Jos. J. Walsh

Ventilation within a coal mine is essential to the welfare of those employed therein, from the standpoint of health, safety, and efficiency. While the saving of life and the preserving of health are the chief reasons for ventilation, efficiency and production are increased. In spite of the fact that we speak of air as having a certain composition, the proportions of oxygen, nitrogen, and carbon dioxide are not fixed, but vary between small limits. The different elements are not chemically united, they are merely mixed and each is free and can be separated with little energy. For this reason air in the mine workings is seldom found in a pure state. Factors that necessitate ventilation in coal mines are those that change the composition of pure air. Contamination of mine air results from the burning of oil-fed flames, the use of explosives, the oxidation of coal, and the liberation of gases by the coal. The extent to which these factors exist governs the size and general plan of the ventilating applianccs required. An efficient ventilating system is one that will furnish air at the working faces in sufficient volume to dilute and render harmless noxious gases and at the same time maintain an oxygen content closely approaching that of pure air. In a well-ventilated mine, the oxygen seldom falls more than 0.5 per cent. below normal. The carbon-dioxide content of the air in the average coal mine will vary from 0.1 to about 0.8 per cent., which amounts are not harmful. Three per cent. of carbon dioxide in air doubles the frequency and the depth of breathing; it is plainly noticeable and if breathed continuously for several hours its effect would probably be harmful. Slight reductions in the oxygen content of the air, such as occur in well-ventilated mines, have no debilitating effect on the worker. A person not exerting himself would fail to observe any unusual physical effect in an atmosphere: containing 17 per cent. of oxygen. This condition, however, or even a condition showing an oxygen content below 20 per cent., would indicate poor ventilation and that the elements which tend to reduce the efficiency of the worker are present, namely water vapor and a high wet-bulb temperature.

Jan 1, 1923