Search Documents

By Ronald M. Tipton

Freeze and thaw deterioration is a serious problem In con¬crete pavements. The main cause of distress Is thought to be the pore structure of coarse aggregate. In an attempt to characterize deleterious pores, the Iowa Pore Index test and the Expected Durability Factor, as Calculated from the mer¬cury intrusion porosimeter, were devised. This study Included freeze-thaw and sodium and magnesium sulfate soundness testing of sixteen carbonate aggregate samples. In addition, the Iowa Pore Index and the Expected Durability factor were determined for each of the samples. All of the Above mentioned physicochemical parameters were examined using bivriate correlation analysis with the In¬tent to evaluate the effectiveness of the Iowa Pore Index and Expected Durability factor for predicting the frost dur¬ability of an aggregate. The results from the bivariate correlation analysis showed no significant correlation, between the Iowa Pore In¬dex And- Expected Durability factor with the other physico¬chemical parameters investigated. Rust interesting is that the Iowa Pore index predicted that All of the tested samples would resist freeze-thaw failure, whereas the Expected Durability factor predicted that -ash sample would he non-durable.

Jan 1, 1987

By The Staff

"IntroductionThe published information concerning treatment of uranium ores has been very limited as far as Canadian ores are concerned. Such information has dealt mainly with refining processes for concentrates or rich ores, designed to recover radium rather than uranium; these methods could not be economically applied to low-grade ores.The purpose of this paper is to describe treatment possibilities for some of the .ores that have been treated at the Mines Branch, and .to show how the character of these ores influences methods and results.What is a Uranium Ore?Prospecting for uranium has been extremely active during the past two years and a great many occurrences of radioactive minerals have been recorded. Such prospecting has been based to a large extent on the use of the Geiger counter in the fie1d. This equipment is an invaluable aid when the results are properly interpreted.Most definitely, indications of high radioactivity do not always prove the presence of a valuable orebody. First we have to determine:(1) Is the radioactivity due to uranium or to thorium. There is no immediate market for thorium.(2) Can the uranium in the ore be economically recovered.Chemical analysis is the most exact method of determining uranium content, but a fair estimate of the uranium, and also of the thorium, content can be made from the difference in gamma and beta activity. The Mines Branch guards against misinterpretation by determining both beta and gamma activities and, if more than a minor amount of thorium is indicated, then a Chemical analysis is made."

Jan 1, 1950

By Raymond E. Healy

Mercurian e1ectrum (Au-Ag-Hg alloy) is the principal Au-bearing phase in the massive sulphide ores at Trout Lake, Manitoba. The average composition of this phase (in wt %) is 49.2 % Ag. 38.7 % Au and 11.0 % Hg, with ranges of 17.34 to 76.47 % Ag, 1.62 to 79.86 % Au and 1.29 to 30.87 % Hg. Compositional variation reflects solid solution in the a-phase of the Ag-Au-Hg system. Backscatter electron imagery reveals systematic zoning and suggests a general crystallization sequence from metamorphic pore fluids of progressively Ag-rich compositions. Investigation of the occurrence of gold in mill products demonstrates that mercurian electrum accounts for over 90 % of the Au in Trout Lake ore. I Invisible" gold in pyrite (x = 0.72 ppm Au) and arsenopyrite (x 30.2 ppm Au) is confirmed by SIMS analyses, and accounts for 7-10 % of the Au in the ore, and 35 % of the Au lost to the tailings. The remaining 65 % of the Au lost to the tailings consists principally of mercurian electrum locked with pyrite. No significant losses of mercurian electrum in the size range amenable to flotation and/or regrinding is indicated.

Jan 1, 1989

By Y. M. Ha, T. D. Nguyen, D. T. Nguyen, H. K. Choi

Conventionally, cement deep mixing (CDM) columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern may be inefficient in cases of spread footings or shallow foundations. This paper first briefly introduces principles of an improved CDM method that can create head-enlarged CDM (termed PF) columns. A simple analysis approach was introduced to obtain optimal shape of PF columns that results in minimum settlement. The effectiveness of this improved method over the conventional CDM method was then illustrated by settlement analysis for an actual footing in a case study using two recommended analytical methods in the literature. Analysis results from the case indicated that by using the same amount of soil-cement mixed volumes, settlement from a footing on PF columns can reduce up to 10 % compared with that from the same footing on CDM columns. In addition, a material quantity comparison for the case indicated that to have the same settlement values the volume of each PF column can be reduced of around 10% compared with that of the CDM column. INTRODUCTION The cement deep mixing (CDM) method is one of the most popular methods in ground improvement works. Details on the method such as construction procedures, necessary equipment and recommendations are described in many references or manuals (e.g. Bruce et al. 2013, BS EN 2015, Kitazume and Terashi 2013). Conventionally, CDM columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern is found inefficient in cases of spread footings or shallow foundations as the upper soil layers are naturally weaker than the deeper ones but are subjected to larger amount of induced stress from the superstructures.

Jan 1, 2019

By Xiyu Gao, Yi Yang, Mark I. Pownceby, Shuiping Zhong, Miao Chen

In the present study, X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray absorption near edge structure (XANES) spectroscopy, and Raman spectroscopy were used to investigate the effect of chloride ions on chalcopyrite bioleaching and chemical leaching at 25 °C. The leaching results show that the addition of chloride ions suppressed the dissolution of chalcopyrite in both chemical and bacterial leaching. In chemical leaching, the solution redox potential in the experiment without Cl− stayed in a range more suitable for chalcopyrite dissolution compared with experiments with Cl− . In bioleaching, the bacteria activity was suppressed by Cl− leading to low dissolution rates of Cu. Surface morphology and chemical speciation studies confirmed the formation of potassium jarosite on the surface of the chalcopyrite leach residues. In addition, S K-edge XANES indicated the formation of trace amount of elemental sulfur and covellite on the mineral surfaces.

By Trevor Saldanha, Nawshad Haque, Will Sikora

This study reported life cycle assessment (LCA) of six copper mines in Australia, Papua New Guinea and Portugal. Inventory data was sourced from published papers, sustainability reports by mining companies, independent technical reports and previous CSIRO studies. Sima Pro software and various databases were used to evaluate life cycle based environmental impacts. The impact indicators were: global warming potential (GWP), acidification potential, water footprint, ecotoxicity potential, ozone depletion potential and human toxicity potential (carcinogenic and non-carcinogenic), abiotic resource depletion potential (minerals and fossil fuels), particulate matter and ionizing radiation. Generally, open pit mines were found to have a GWP of approximately 1.0 t CO2-eq/t Cu concentrate while underground mines had approximately 1.3 to 1.8 t CO2-eq/t Cu concentrate. Environmental impacts varied between mines considerably due to several factors, most notably: ore grade, mining method, flowsheets and ore mineralogy. Energy consumption and sources were significant contributors to most impact categories.

Mar 1, 2018

By Li Chongyang, Liu Baolan, Jia Xiaolin, Li Suping

An Al/Al2O3 gradient coating applied on a heat-resistant stainless steel was prepared through a slurry process by using aluminum and ?-Al2O3 powders as the transition filler material, alpha alumina as the surface coating material, aluminum dihydrogen phosphate as the binder, and sodium molybdate as the corrosion inhibitor. The effects of heat treatment temperature, adhesive/filler ratio and ?-Al2O3 content on the bonding strength, microhardness and thermal shock resistance were investigated. The crystal phase and microstructure were characterized by XRD and SEM. The results indicated that the composition of the coating changed continuously from surface to coating-substrate interface. The coating could offer high bonding strength and good thermal shock resistance when heat treated at 700°C.

Jan 1, 2010

By James D. Navratil

Advances in hydrometallurgy require the introduction of new separation and purification processes, but they can be complex, costly and energy intensive. Chromatographic processes have low energy requirements and possess very high separation efficiencies. However, they have not yet made the great industrial impact that might be expected from their benefits. The large-scale and difficult separation of rare earths would greatly benefit from an improved continuous chromatographic operational device. Truly continuous, multicomponent chromatographic separations may be achieved by means of the continuous annular chromatograph. Work has been Initiated at The University of New South Wales involving the improvement and development of such equipment for the separation and purification of rare earths.

Jan 1, 1990

By Jonguk Kim

Texture and geochemical composition of hydrogenous ferromanganese crust from relatively adjacent three seamounts (OSM2 at 157°35'E, 13°55'N, Lomilik at 161°37'E, 11°42'N and Lemkein at 165°05'E, 9°18'N) near the Marshall Islands in the western Pacific (Figure 1) were investigated in order to elucidate their growth history. These seamounts, located in different latitudes, are along a line that is parallel with the direction of Pacific plate movement. Thick crusts commonly have three or four distinct layers (Figure 2): (1) layer 1, uppermost layer, is black, dense, and has a botryoidal, columnar, or laminated texture; (2) layer 2, overlain by layer 1, is Fe-stained, porous to vuggy and filled with sediment; (3) layer 3, phosphatized layer, is black, massive, dense, and impregnated by CFA, (4) layer 4 shows parallel to undulatory laminated texture and cut by CFA-filled veins. Layer 1 and 2, unphosphatized young layer, are observed in crust samples collected from all seamounts. However, lower part of the crust shows different textures in different seamounts. Both layer 3 and 4 are found in thick crust from OSM2 but layer 4 is absent in crust samples from Lemkein and Lomilik. All the uppermost layers (layer 1) from three seamounts have similar textural and geochemical characteristics. Layer 2 is overlain by layer 1, is porous, partly Fe-stained, and sediment-infilled. In previous studies, layers 1 and 2 have grown in different oceanic environment. Textural and geochemical properties show that layer 1 has grown under relatively higher bottom water activity and lower productive environment than layer 2. Carbonate and detrital materials in layer 1 are not abundant compared to layer 2. Layer 2 can be assumed to have grown under equatorial high productivity zone (EHPZ) while layer 1 has started to grow when the seamount left from the EHPZ.

Jan 1, 2003

By A. O. Bartell

Do you know that valuable clues to the geology and mineralization of a district can be found in a handful of sand from a stream bed draining the area? This handful of sand has a story to tell to those who have a little patience. The handful of sand may contain tiny specks of valuable minerals (gold, scheelite, cinnabar, chromite, tourmaline-to mention a few), that will lure you upstream with the hope of uncovering a new deposit. More practically, this handful of sand can indicate the type of rocks that are exposed by the drainage system. Any mineral that has a specific gravity of 3.5 or higher can be separated from soil by panning. Garnet and pyrite, for example, can indicate an outcrop of metamorphic rock. In one district where the writer prospected, small boat-shaped orthorhombic crystals of topaz always indicated the presence of andesite outcrops.

Jan 1, 1948

By Weijie Wei, Jinwang Zhang, Shengli Yang

In longwall top-coal caving (LTCC) mining with an inclined seam, the recovery rate is low and equipment stability is poor due to the unbalanced top-coal drawing process. To address these problems, this paper proposes the dynamic group caving method (DGCM), whose basic premise is that when the drawn volume of top coal from a support reaches about half, the next support begins drawing top coal, and the drawing process between the two supports is half done. Using particle flow code (PFC), the caving mechanism of top coal under DGCM was investigated. The results are of significance to realize high efficiency and precise caving in LTCC mining with an inclined seam.

By S. J. Schatzel, V. Gangrade

A ventilation research study was conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) and a cooperating longwall trona mine in the Green River basin of Wyoming in the United States. The objective of the study was to evaluate the movement of longwall face air and exchanges between the face and worked-out areas to document the presence or absence of face airflow pathways between these locations. Tracer gas experiments using sulfur hexafluoride (SF6  ) were conducted to describe air movement on the face and in the mined portion of the active panel. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of gases emitted from the face and caved gob.

By Thomas Barczak

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear ?abutment? moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

Jan 1, 2007

By A. B. Hooker

[Permissible electric cap lamps represent a workable balance between the amount of light needed and the various limiting conditions, such as the weight the miner can carry conveniently, cost of the lamp, including upkeep, and adequacy or practicability of the lamp as regards safety, mechanical strength, and general performance. Other things being equal, the coot desirable lamp is one that gives the greatest amount of useful light. Conversely, with a given amount of light the most desirable lamp is one that its the most efficient respecting weight, cost, and performance.]

Jan 1, 1935

By Vern Miller

The Bureau of Mines developed a detector for controlling sorting devices to separate the copper-bearing fragments from the barren portion of Michigan native copper and western porphyry copper ores. A successful sorter could be used to preconcentrate the ore and eliminate costly hoisting or hauling of waste. An induction balance unit was developed and used in sorting tests on crushed sized -1+1/2-inch (-2.5+1.3-cm) ores from the Kingston (0.9 pct CU) and Centennial (1.6 pct Cu) mines of Upper Michigan. Concentrates of 4.0 pct and 7.5 pct Cu, respectively, were obtained at recoveries of 85 and 80 pct of the copper in the feed. Eighty percent of the sorted ore was rejected as tailing. Sorting larger fragments improved the separation efficiency. Tests on -4+2-inch (-10+5-cm) sized Kingston (1.6 pct Cu) and Centennial (2.1 pct Cu) ore samples yielded concentrates of 4.3 and 4.5 pct Cu, respectively, with corresponding recoveries of 92 and 91 pct. About 60 pct of the sorted ore was discarded as tailing. Porphyry copper sulfide ores also responded to electronic sorting but at a lower separation efficiency. Sorting response was affected by the degree of segregation.

Jan 1, 1976

By I. Iwasaki

The presence of calcium ion in iron ore pulps causes heterocoagulation of montmrillonite on hematite leading to indiscriminate dispersion. Two methods were investigated to control the adverse effect of montmorillonite: chemical method using such complexing agents as EDTA and sodium tripolyphosphate, and mechanical method involving ultrasonic treatment. Their roles in controlling the adverse effect were investigated by zeta potential measurements, starch adsorption tests, and flocculation and selective flocculation tests.

Jan 1, 1986

By S. D. Bearden

Color enhances expression and communication in all physical objects experienced in life. Pigments provide color and in some applications have a specific additional function. Natural iron oxides are widely distributed throughout the world but only a few deposits are sufficiently pure and possess acceptable color and brightness properties to merit their processing into pigment form. Ochre, the common name for goethite ore, is the best and most under used material in the buff colored pigment market. The geological occurrence of ochre in the basal Shady Formation of the Cartersville Mining District (Georgia) is described. Exploration, processing, and product applications of New Riverside Ochre Company, Inc. are discussed. An overview of the worldwide pigment market is presented with emphasis placed upon the North American activity in iron oxide production and application. The purpose of this paper is to increase the awareness of ochre and its potential market in the colored iron oxide pigment industry, encourage research on the origin of ochre deposits, and stimulate interest in new applications of this unique substance.

Feb 27, 2013

By Ernest Y. Baafi

The technique of linear kriging as a grade estimation method of mining blocks is reasonably established in the mining industry. Because of the nonbias condition imposed in kriging which requires that the kriging weights (?i) add up to one, negative weights are sometimes used in kriging. The use of negative weights is not justifiable from the practical standpoint. Also, negative block grades can be obtained in some extreme situations which makes no practical sense. To guarantee non-negative weights an additional constraint is required in the kriging system of equations. Unfortunately, the nonnegative weight constraint results in a set of non- linear system of equations. In this paper, a derivation of the resulting set of nonlinear equations is presented and a numerical algorithm is developed for the solution of the equations. Because the algorithm developed does not remove negative weights arbitrarily, optimal nonnegative weights are always guaranteed. Results obtained using the developed algorithm were compared with those using the standard linear kriging, in terms of computer time and the estimation results. Both the computer time and the kriging variance were found to be higher with nonnegative constraint, as expected. However, some systematic pattern was observed in the kriged values (i.e., over or under estimation) with or without the nonnegative constraint. The study also demonstrated when one should generally expect negative kriging weights in practice, and what practical impact the negative weights can have on the kriging estimates.

Jan 1, 1984

By H. J. Booss

THERE is a considerable lack of data on thermody-namic properties of hard-metal alloys. Only two papers 1,2 give mean values of specific heat in an unknown temperature range; more recently the author3 gave more detailed information on the mean specific heat in the temperature range from 20" to -190° C.. EXPERIMENTAL 1) Method—Experimental procedure followed a method suggested by Oelsen and coworkers.4 It requires samples of some 100 g of weight. The time of measurement is prolonged (30 min) but one run allows the measurement of a lot of positions on the heat-content curve. Results4 were found to be in good agreement with "best values" given by kelley,5 Kubaschewsky and Evans,6 etal.

Jan 1, 1960

By Gary E. Sherman

This report presents a Bureau of Mines study on the cost of mine permitting and compliance with environmental regulations in Alaska. It discusses permitting requirements and procedures for placer and lode mines. Placer miners must comply with recently established (1988) water quality regulations and effluent treatment requirements. To estimate the impact differing treatment options (no recycle, 100% recycling, and flocculation) have on a placer mine's rate of return, three models (1,500, 1,000, and 500 yd3/d) were simulated. Rates of return for these models show a marked decrease as effluent treatment is increased. The incremental increase in operating cost from one treatment option to the next is relatively small; however the opportunity cost of lost production if' significant and accounts for the decreasing rate of return with increased effluent treatment. Lode mines face greater costs for permitting and compliance than similarly sized placer mines as a result of the impact of the operation. Direct permitting costs for lode mines range from 2 to 6% of total project cost, with 4% the most common figure cited by industry. Total costs for permitting and compliance are approximately double those for permitting. Indirect costs associated with compliance include mitigation, monitoring, and reclamation.

Jan 1, 1991